EPCOS B82720S2301N040 Current-compensated smd ring core double choke Datasheet

Power line chokes
Current-compensated SMD ring core double chokes
250 V AC, 0.3 … 2 A, 1.1 … 22 mH, +40 °C
Series/Type:
B82720S
Date:
July 2012
Data Sheet
EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
Power line chokes
B82720S
Current-compensated ring core double chokes
Rated voltage 250 V AC
Rated current 0.3 ... 2 A
Rated inductance 1.1 ... 22 mH
Construction
■
■
■
■
■
Current-compensated ring core double choke
Ferrite core with epoxy coating (UL 94 V-0)
LCP case (UL 94 V-0)
Silicone potting
Sector winding
Features
■ Approx. 0.7% stray inductance for differential-mode
interference suppression
■ Suitable for reflow soldering
■ Design complies with EN 60938-2 (VDE 0565-2) and UL 1283
■ RoHS-compatible
Applications
■ Suppression of common-mode interferences
■ Compact electronic ballasts in lamps
■ Compact switch-mode power supplies
Terminals
■ Base material CuSn6
■ Layer composition Ni, Sn
■ Hot-dipped
Marking
■ Marking on component:
Manufacturer, ordering code, rated inductance, rated current,
graphic symbol, rated voltage, date of manufacture (YYWWD)
■ Minimum data on reel:
Manufacturer, ordering code, rated inductance,
rated current, quantity, date of packing
Delivery mode and packing unit
■ 24-mm blister tape, wound on 330-mm  reel
■ Packing unit: 250 pcs./reel
Please read Cautions and warnings and
Important notes at the end of this document.
2
07/12
Power line chokes
B82720S
Current-compensated ring core double chokes
Layout recommendation
2.5
Dimensional drawing and pin configuration
5
1
8
1.6
5
4
12
17.6
IND0244-2
_ 0.05 1)
0.4 +0.1
8±0.2
10.5±0.2
14.9±0.3
14.5 max.
0˚... 6˚
2.5
_ 0.05 1)
0.6 +0.1
5±0.1
2.5±0.1
2.5±0.1
2.2±0.2 1)
16.6±0.4
13.3 max.
1
2
8
7
3
4
6
5
0.1
Marking
1) Soldering area
IND0243-T-E
Tolerances to ISO 2768-C unless otherwise noted.
Dimensions in mm.
Taping and packing
Blister tape
Reel
Dimensions in mm
Please read Cautions and warnings and
Important notes at the end of this document.
3
07/12
Power line chokes
B82720S
Current-compensated ring core double chokes
Technical data and measuring conditions
Rated voltage VR
250 V AC (50/60 Hz)
Test voltage Vtest
1500 V AC, 2 s (line/line)
Rated temperature TR
+40 °C
Rated current IR
Referred to 50 Hz and rated temperature
Rated inductance LR
Measured with Agilent 4284A at 10 kHz, 0.1 mA, +20 °C
Inductance is specified per winding.
Inductance tolerance
–30/+50% at +20 °C
Inductance decreaseL/L0
< 10% at DC magnetic bias with IR, +20 °C
Stray inductance Lstray,typ
Measured with Agilent 4284A at 10 kHz, 5 mA, +20 °C,
typical values
DC resistance Rtyp
Measured at +20 °C, typical values, specified per winding
Solderability (lead free)
Sn96.5Ag3.0Cu0.5: +(245 5) °C, (3 0.3) s
Wetting of soldering area 95%
(to IEC 60068-2-58, test Td)
Resistance to soldering heat
+(260 5) °C, (10 1) s (to IEC 60068-2-58, test Td)
Climatic category
40/125/56 (to IEC 60068-1)
Storage conditions (packaged)
–25 °C … +40 °C, 75% RH
Weight
Approx. 2.5 g
Characteristics and ordering codes
IR
LR
Lstray,typ
Rtyp
A
mH
H
m
Ordering code
0.3
22
130
1500
B82720S2301N042
0.3
12
80
1100
B82720S2301N040
0.6
4.4
30
400
B82720S2601N040
1.0
3.0
20
220
B82720S2102N040
1.5
1.6
10
110
B82720S2152N040
2.0
1.1
6
65
B82720S2202N040
Please read Cautions and warnings and
Important notes at the end of this document.
4
07/12
Power line chokes
B82720S
Current-compensated ring core double chokes
Current derating Iop/IR
versus temperature TA
Impedance |Z| versus frequency f
measured with windings in parallel at +20 °C,
typical values
IND0611-S
10 6
Ω
B82720
| Z|
10 5
10 4
S2301N042
S2301N040
S2601N040
S2102N040
S2152N040
S2202N040
10 3
10 2 4
10
10 5
10 6
Hz 10 7
f
5
07/12
Power line chokes
B82720S
Current-compensated ring core double chokes
Recommended reflow soldering profile
Pb-free solder material (based on JEDEC J-STD 020C)
t3
T4
T3
t2
T2
T1
t1
IND0814-F
T1
T2
T3
T4
t1
t2
t3
°C
°C
°C
°C
s
s
s
150
200
217
245
< 110
< 90
< 30 @ T4 –5 °C
Time from +25 °C to T4: max 300 s
Max. numbers of reflow cycles: 3
Please read Cautions and warnings and
Important notes at the end of this document.
6
07/12
Cautions and warnings
Current-compensated ring core double chokes
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there. Derating must be applied
in case the ambient temperature in the application exceeds the rated temperature of the
component.
– Ensure the operation temperature (which is the sum of the ambient temperature and the
temperature rise caused by losses / self-heating) of the component in the application does not
exceed the maximum value specified in the climatic category.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
7
07/12
Important notes
Current-compensated ring core double chokes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
8
07/12
Similar pages