Cadeka CLC1606IST5X 1.3ghz current feedback amplifier Datasheet

Data Sheet
A m p l i fy t h e H u m a n E x p e r i e n c e
Comlinear CLC1606
®
1.3GHz Current Feedback Amplifier
The COMLINEAR CLC1606 is a high-performance, current feedback amplifier with superior bandwith and video specifications. The CLC1606 provides
1.3GHz unity gain bandwidth, ±0.1dB gain flatness to 150MHz, and provides
3,300V/μs slew rate exceeding the requirements of high-definition television
(HDTV) and other multimedia applications. The COMLINEAR CLC1606 highperformance amplifier also provide ample output current to drive multiple
video loads.
The COMLINEAR CLC1606 is designed to operate from ±5V or +5V supplies.
It consumes only 7.5mA of supply current. The combination of high-speed
and excellent video performance make the CLC1606 well suited for use in
many general purpose, high-speed applications including standard definition
and high definition video. Data communications applications benefit from
the CLC1606’s total harmonic distortion of -68dBc at 10MHz and fast settling
time to 0.1%.
Applications
n RGB video line drivers
n High definition video driver
n Video switchers and routers
n ADC buffer
n Active filters
n High-speed instrumentation
n Wide dynamic range IF amp
Typical Application - Driving Dual Video Loads
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
General Description
features
n 1.2GHz -3dB bandwidth at G=2
n 3,300V/μs slew rate
n 0.01%/0.01˚ differential gain/
phase error
n 7.5mA supply current
n 875MHz large signal bandwidth
n 120mA output current (easily drives
three video loads)
n Fully specified at 5V and ±5V supplies
n CLC1606: Pb-free SOT23-5
n CLC1606: Pb-free SOIC-8
Rev 1A
Ordering Information
Part Number
Package
Pb-Free
RoHS Compliant
Operating Temperature Range
Packaging Method
CLC1606IST5X
SOT23-5
Yes
Yes
-40°C to +85°C
Reel
CLC1606ISO8
SOIC-8
Yes
Yes
-40°C to +85°C
Rail
CLC1606ISO8X
SOIC-8
Yes
Yes
-40°C to +85°C
Reel
Moisture sensitivity level for all parts is MSL-1.
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
Data Sheet
SOT23-5 Pin Assignments
SOT23-5 Pin Configuration
1
-V S
2
+IN
3
+
5
+VS
4
-IN
-
SOIC Pin Configuration
Pin Name
1
OUT
Output
2
-VS
Negative supply
3
+IN
Positive input
4
-IN
Negative input
5
+VS
Positive supply
SOIC Pin Assignments
Pin No.
NC
1
8
NC
-IN1
2
7
+VS
+IN1
3
6
OUT
-V S
4
Description
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
OUT
Pin No.
5
NC
Pin Name
Description
1
NC
No connect
2
-IN1
Negative input, channel 1
3
+IN1
Positive input, channel 1
4
-VS
Negative supply
5
NC
No connect
6
OUT
Output
7
+VS
Positive supply
8
NC
No connect
Rev 1A
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
2
Data Sheet
Absolute Maximum Ratings
The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device
should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the
operating conditions noted on the tables and plots.
Supply Voltage
Input Voltage Range
Continuous Output Current
Min
Max
Unit
0
-Vs -0.5V
14
+Vs +0.5V
120
V
V
mA
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Parameter
Reliability Information
Parameter
Junction Temperature
Storage Temperature Range
Lead Temperature (Soldering, 10s)
Package Thermal Resistance
5-Lead SOT23
8-Lead SOIC
Min
Typ
-65
Max
Unit
150
150
260
°C
°C
°C
221
100
°C/W
°C/W
Notes:
Package thermal resistance (qJA), JDEC standard, multi-layer test boards, still air.
ESD Protection
Product
SOT23-5
Human Body Model (HBM)
Charged Device Model (CDM)
2kV
1kV
Recommended Operating Conditions
Min
Operating Temperature Range
Supply Voltage Range
-40
4.5
©2007-2008 CADEKA Microcircuits LLC Typ
Max
Unit
+85
12
°C
V
www.cadeka.com
Rev 1A
Parameter
3
Data Sheet
Electrical Characteristics at +5V
TA = 25°C, Vs = +5V, Rf = 270Ω, RL = 150Ω to VS/2, G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
UGBW
-3dB Bandwidth
1000
MHz
BWSS
-3dB Bandwidth
G = +2, VOUT = 0.5Vpp
900
MHz
BWLS
Large Signal Bandwidth
G = +2, VOUT = 1Vpp
800
MHz
BW0.1dBSS
0.1dB Gain Flatness
G = +2, VOUT = 0.5Vpp
132
MHz
BW0.1dBLS
0.1dB Gain Flatness
G = +2, VOUT = 1Vpp
140
MHz
Time Domain Response
tR, tF
Rise and Fall Time
VOUT = 1V step; (10% to 90%)
0.6
ns
tS
Settling Time to 0.1%
VOUT = 1V step
10
ns
OS
Overshoot
VOUT = 0.2V step
1
%
SR
Slew Rate
1V step
1500
V/µs
Distortion/Noise Response
HD2
2nd Harmonic Distortion
1Vpp, 5MHz
-74
dBc
HD3
3rd Harmonic Distortion
1Vpp, 5MHz
-70
dBc
THD
Total Harmonic Distortion
1Vpp, 5MHz
68
dB
IP3
Third-Order Intercept
1Vpp, 10MHz
36
dBm
DG
Differential Gain
NTSC (3.58MHz), AC-coupled, RL = 150Ω
0.01
%
DP
Differential Phase
NTSC (3.58MHz), AC-coupled, RL = 150Ω
0.01
°
en
Input Voltage Noise
> 1MHz
3
nV/√Hz
ini
Input Current Noise
> 1MHz, Inverting
20
pA/√Hz
> 1MHz, Non-inverting
30
pA/√Hz
0
mV
3.7
µV/°C
DC Performance
VIO
dVIO
Ibn
dIbn
Ibi
dIbi
Input Offset Voltage
Average Drift
Input Bias Current - Non-Inverting
Average Drift
Input Bias Current - Inverting
Average Drift
Power Supply Rejection Ratio
IS
Supply Current
DC
µA
100
nA/°C
±6.0
µA
56
nA/°C
55
dB
6.5
mA
150
kΩ
Input Characteristics
RIN
Input Resistance
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
Non-inverting
Inverting
70
Ω
1.0
pF
±1.5
V
DC
50
dB
0.1
Ω
Output Characteristics
RO
Output Resistance
Closed Loop, DC
VOUT
Output Voltage Swing
RL = 150Ω
IOUT
Output Current
©2007-2008 CADEKA Microcircuits LLC ±1.5
V
±120
mA
www.cadeka.com
4
Rev 1A
PSRR
±3.0
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
G = +1, Rf = 390Ω, VOUT = 0.5Vpp
Data Sheet
Electrical Characteristics at ±5V
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
-3dB Bandwidth
G = +1, Rf = 390Ω, VOUT = 0.5Vpp
1300
MHz
BWSS
-3dB Bandwidth
G = +2, VOUT = 0.5Vpp
1200
MHz
BWLS
Large Signal Bandwidth
G = +2, VOUT = 2Vpp
875
MHz
BW0.1dBSS
0.1dB Gain Flatness
G = +2, VOUT = 0.5Vpp
150
MHz
BW0.1dBLS
0.1dB Gain Flatness
G = +2, VOUT = 2Vpp
150
MHz
Time Domain Response
tR, tF
Rise and Fall Time
VOUT = 2V step; (10% to 90%)
0.5
ns
tS
Settling Time to 0.1%
VOUT = 2V step
13
ns
OS
Overshoot
VOUT = 0.2V step
1
%
SR
Slew Rate
2V step
3300
V/µs
Distortion/Noise Response
HD2
2nd Harmonic Distortion
2Vpp, 5MHz
-71
dBc
HD3
3rd Harmonic Distortion
2Vpp, 5MHz
-71
dBc
THD
Total Harmonic Distortion
2Vpp, 5MHz
-68
dB
IP3
Third-Order Intercept
2Vpp, 10MHz
39
dBm
DG
Differential Gain
NTSC (3.58MHz), AC-coupled, RL = 150Ω
0.01
%
DP
Differential Phase
NTSC (3.58MHz), AC-coupled, RL = 150Ω
0.01
°
en
Input Voltage Noise
> 1MHz
3
nV/√Hz
ini
Input Current Noise - Inverting
> 1MHz, Inverting
20
pA/√Hz
> 1MHz, Non-inverting
30
pA/√Hz
DC Performance
VIO
dVIO
Ibn
dIbn
Ibi
dIbi
Input Offset Voltage(1)
-10
0.5
-45
±3.0
Average Drift
3.7
Input Bias Current - Non-Inverting (1)
Average Drift
-50
Average Drift
IS
Supply Current
µV/°C
DC
40
50
µA
56
nA/°C
50
dB
7.5
(1)
µA
nA/°C
9.5
mA
Input Characteristics
RIN
Input Resistance
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio (1)
Non-inverting
150
Inverting
170
k
1.0
pF
DC
40
kΩ
±4.0
V
50
dB
0.1
Ω
Output Characteristics
RO
Output Resistance
Closed Loop, DC
VOUT
Output Voltage Swing
RL = 150Ω
IOUT
Output Current
(1)
±3.0
±3.7
V
±280
mA
Notes:
1. 100% tested at 25°C
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
5
Rev 1A
Power Supply Rejection Ratio (1)
±7.0
mV
45
100
Input Bias Current - Inverting (1)
PSRR
10
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
UGBW
Data Sheet
Typical Performance Characteristics
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
Non-Inverting Frequency Response
Inverting Frequency Response
0
0
Normalized Gain (dB)
Normalized Gain (dB)
G = -1
G=1
Rf = 499Ω
G=2
-3
G=5
G = 10
-6
G = -2
G = -5
-3
G = -10
-6
VOUT = 0.5Vpp
VOUT = 0.5Vpp
-9
-9
0.1
1
10
100
1000
0.1
1
Frequency (MHz)
100
1000
Frequency Response vs. RL
1
6
5
0
4
Normalized Gain (dB)
CL = 1000pF
Rs = 3.3Ω
-1
Normalized Gain (dB)
10
Frequency (MHz)
Frequency Response vs. CL
CL = 500pF
Rs = 5Ω
-2
-3
CL = 100pF
Rs = 10Ω
-4
CL = 50pF
Rs = 15Ω
-5
-6
3
2
1
0
-1
RL = 100Ω
-2
RL = 50Ω
-3
-4
CL = 20pF
Rs = 20Ω
VOUT = 0.5Vpp
VOUT = 0.5Vpp
-5
-7
RL = 25Ω
-6
0.1
1
10
100
1000
0.1
1
10
100
1000
Rev 1A
Frequency (MHz)
Frequency (MHz)
Frequency Response vs. VOUT
Frequency Response vs. Temperature
3
2
2
1
1
0
Normalized Gain (dB)
Normalized Gain (dB)
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
3
G=1
Rf = 390Ω
3
0
-1
VOUT = 1Vpp
-2
VOUT = 2Vpp
-3
-4
VOUT = 4Vpp
-5
-1
+ 25degC
-2
- 40degC
-3
+ 85degC
-4
-5
VOUT = 0.2Vpp
-6
-6
-7
-7
0.1
1
10
Frequency (MHz)
©2007-2008 CADEKA Microcircuits LLC 100
1000
0.1
1
10
100
1000
10000
Frequency (MHz)
www.cadeka.com
6
Data Sheet
Typical Performance Characteristics
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
Non-Inverting Frequency Response at VS = 5V
2
Inverting Frequency Response at VS = 5V
G = -1
0
G=2
Normalized Gain (dB)
Normalized Gain (dB)
0
-1
-2
-3
G=5
-4
-5
G = 10
-6
G = -2
G = -5
-3
G = -10
-6
-7
VOUT = 0.5Vpp
-8
VOUT = 0.5Vpp
-9
-9
0.1
1
10
100
1000
0.1
1
Frequency (MHz)
100
1000
Frequency Response vs. RL at VS = 5V
1
4
3
0
2
Normalized Gain (dB)
CL = 1000pF
Rs = 3.3Ω
-1
Normalized Gain (dB)
10
Frequency (MHz)
Frequency Response vs. CL at VS = 5V
CL = 500pF
Rs = 5Ω
-2
-3
CL = 100pF
Rs = 10Ω
-4
CL = 50pF
Rs = 15Ω
-5
-6
VOUT = 0.5Vpp
1
0
-1
RL = 100Ω
-2
RL = 50Ω
-3
-4
CL = 20pF
Rs = 20Ω
RL = 25Ω
VOUT = 0.5Vpp
-5
-7
-6
0.1
1
10
100
1000
0.1
1
1
0
0
Normalized Gain (dB)
2
1
-1
VOUT = 1Vpp
VOUT = 2Vpp
-4
VOUT = 3Vpp
-5
1000
Frequency Response vs. Temperature at VS = 5V
2
-3
100
Frequency (MHz)
Frequency Response vs. VOUT at VS = 5V
-2
10
Rev 1A
Frequency (MHz)
Normalized Gain (dB)
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
3
G=1
Rf = 390Ω
1
-1
-2
+ 25degC
-3
- 40degC
-4
-5
-6
+ 85degC
VOUT = 0.2Vpp
-6
-7
-7
0.1
1
10
Frequency (MHz)
©2007-2008 CADEKA Microcircuits LLC 100
1000
0.1
1
10
100
1000
10000
Frequency (MHz)
www.cadeka.com
7
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
Gain Flatness
Gain Flatness at VS = 5V
0.8
0.7
0.6
0.5
1.1
Normalized Gain (dB)
Normalized Gain (dB)
1.3
0.9
0.7
0.5
0.3
0.1
0.4
0.3
0.2
0.1
0
-0.1
-0.2
-0.1
VOUT = 2Vpp
RL = 150Ω
Rf = 270Ω
-0.3
VOUT = 2Vpp
RL = 150Ω
Rf = 270Ω
-0.3
-0.4
-0.5
-0.5
0.1
1
10
100
1000
0.1
1
10
Frequency (MHz)
100
1000
Frequency (MHz)
-3dB Bandwidth vs. VOUT at G=10
-3dB Bandwidth vs. VOUT at G=10, VS = 5V
600
450
-3dB Bandwidth (MHz)
-3dB Bandwidth (MHz)
550
500
450
400
400
350
300
350
G = 10
300
250
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.0
0.5
2.0
2.5
3.0
Input Voltage Noise
2.0
20
VS = ±5.0V
Input Voltage Noise (nV/√Hz)
Output Resistance (Ω)
1.5
VOUT (VPP)
Closed Loop Output Impedance vs. Frequency
1.8
1.0
Rev 1A
VOUT (VPP)
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
10K
100K
1M
Frequency (Hz)
©2007-2008 CADEKA Microcircuits LLC 10M
100M
15
10
5
0
0.0001
0.001
0.01
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
1.7
1.5
0.1
1
10
Frequency (MHz)
www.cadeka.com
8
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
2nd Harmonic Distortion vs. RL
3rd Harmonic Distortion vs. RL
-55
-60
-60
RL = 150Ω
-65
RL = 150Ω
-70
Distortion (dBc)
Distortion (dBc)
-65
-75
-80
-85
RL = 499Ω
-90
-70
-75
-80
RL = 499Ω
-85
-90
-95
-95
VOUT = 2Vpp
-100
VOUT = 2Vpp
-100
0
5
10
15
20
0
5
Frequency (MHz)
2nd Harmonic Distortion vs. VOUT
15
20
3rd Harmonic Distortion vs. VOUT
-60
-60
-65
-65
-75
10MHz
-70
10MHz
-70
Distortion (dBc)
Distortion (dBc)
10
Frequency (MHz)
5MHz
-80
-75
5MHz
-80
-85
1MHz
-85
-90
RL = 150Ω
-90
0.5
0.75
1MHz
RL = 150Ω
-95
1
1.25
1.5
1.75
2
2.25
2.5
0.5
0.75
1
1.25
1.5
1.75
2
2.25
2.5
Rev 1A
Output Amplitude (Vpp)
Output Amplitude (Vpp)
CMRR vs. Frequency
PSRR vs. Frequency
0
0
-10
-20
-20
PSRR (dB)
CMRR (dB)
VS = ±5.0V
-10
-30
-40
-50
-30
-40
-50
-60
-60
10k
100k
1M
Frequency (Hz)
©2007-2008 CADEKA Microcircuits LLC 10M
100M
10K
100K
1M
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
-55
10M
100M
Frequency (Hz)
www.cadeka.com
9
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
Small Signal Pulse Response at VS = 5V
0.125
2.625
0.1
2.6
0.075
2.575
2.55
0.025
2.525
Voltage (V)
0.05
0
-0.025
2.5
2.475
-0.05
2.45
-0.075
2.425
-0.1
2.4
-0.125
2.375
0
20
40
60
80
100
120
140
160
180
200
0
20
40
60
80
Time (ns)
120
140
160
180
200
Large Signal Pulse Response at VS = 5V
3
4
2
3.5
1
3
Voltage (V)
Voltage (V)
Large Signal Pulse Response
0
2.5
-1
2
-2
1.5
-3
1
0
20
40
60
80
100
120
140
160
180
200
0
20
40
60
120
140
160
180
200
Differential Gain & Phase DC Coupled Output
0.06
0.015
0.05
Diff Gain (%) / Diff Phase (°)
0.02
0.01
DG
0
DP
-0.005
-0.01
100
Time (ns)
Differential Gain & Phase AC Coupled Output
0.005
80
Rev 1A
Time (ns)
Diff Gain (%) / Diff Phase (°)
100
Time (ns)
DP
0.04
0.03
0.02
0.01
DG
0
-0.01
RL = 150Ω
AC coupled
-0.015
RL = 150Ω
DC coupled
-0.02
-0.7
-0.5
-0.3
-0.1
0.1
Input Voltage (V)
©2007-2008 CADEKA Microcircuits LLC 0.3
0.5
0.7
-0.7
-0.5
-0.3
-0.1
0.1
0.3
0.5
0.7
Input Voltage (V)
www.cadeka.com
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Voltage (V)
Small Signal Pulse Response
10
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 270Ω, RL = 150Ω, G = 2; unless otherwise noted.
Differential Gain & Phase DC Coupled at VS = ±2.5V
0.05
0.005
0.04
0
Diff Gain (%) / Diff Phase (°)
0.01
DP
-0.005
-0.01
-0.015
DG
-0.02
-0.025
RL = 150Ω
DC coupled
AC
-0.35
0.02
0.01
0
-0.01
DG
-0.02
-0.03
-0.03
DP
0.03
RL = 150Ω
DC coupled
-0.04
-0.25
-0.15
-0.05
0.05
Input Voltage (V)
0.15
0.25
0.35
-0.35
-0.25
-0.15
-0.05
0.05
0.15
0.25
0.35
Input Voltage (V)
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Diff Gain (%) / Diff Phase (°)
Differential Gain & Phase AC Coupled Output at VS = ±2.5V
Rev 1A
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
11
Data Sheet
General Information - Current Feedback
Technology
Advantages of CFB Technology
CFB also alleviates the traditional trade-off between
closed loop gain and usable bandwidth that is seen with
a VFB amplifier. With CFB, the bandwidth is primarily determined by the value of the feedback resistor, Rf. By using optimum feedback resistor values, the bandwidth of a
CFB amplifier remains nearly constant with different gain
configurations.
When designing with CFB amplifiers always abide by these
basic rules:
• Use the recommended feedback resistor value
• Do not use reactive (capacitors, diodes, inductors, etc.)
elements in the direct feedback path
• Avoid stray or parasitic capacitance across feedback resistors
• Follow general high-speed amplifier layout guidelines
VIN
Ierr
x1
Zo*Ierr
VOUT
Rf
RL
Rg
VOUT
VIN
= 1+
Rf
Rg
+
1+
1
Rf
Eq. 1
Zo(jω)
Figure 1. Non-Inverting Gain Configuration with First
Order Transfer Function
©2007-2008 CADEKA Microcircuits LLC VIN
Rg
VOUT
VIN
VOUT
Rf
= −
Rf
Rg
+
1+
1
Rf
RL
Eq. 2
Zo(jω)
Figure 2. Inverting Gain Configuration with First Order
Transfer Function
CFB Technology - Theory of Operation
Figure 1 shows a simple representation of a current feedback amplifier that is configured in the traditional noninverting gain configuration.
Instead of having two high-impedance inputs similar to a
VFB amplifier, the inputs of a CFB amplifier are connected
across a unity gain buffer. This buffer has a high impedance input and a low impedance output. It can source or
sink current (Ierr) as needed to force the non-inverting
input to track the value of Vin. The CFB architecture employs a high gain trans-impedance stage that senses Ierr
and drives the output to a value of (Zo(jω) * Ierr) volts.
With the application of negative feedback, the amplifier
will drive the output to a voltage in a manner which tries
to drive Ierr to zero. In practice, primarily due to limitations on the value of Zo(jω), Ierr remains a small but
finite value.
A closer look at the closed loop transfer function (Eq.1)
shows the effect of the trans-impedance, Zo(jω) on the
gain of the circuit. At low frequencies where Zo(jω) is very
large with respect to Rf, the second term of the equation
approaches unity, allowing Rf and Rg to set the gain. At
higher frequencies, the value of Zo(jω) will roll off, and
the effect of the secondary term will begin to dominate.
The -3dB small signal parameter specifies the frequency
where the value Zo(jω) equals the value of Rf causing the
gain to drop by 0.707 of the value at DC.
For more information regarding current feedback amplifiers, visit www.cadeka.com for detailed application notes,
such as AN-3: The Ins and Outs of Current Feedback Amplifiers.
www.cadeka.com
12
Rev 1A
• Ensure proper precautions have been made for driving
capacitive loads
Ierr
Zo*Ierr
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
The CLC1606 Family of amplifiers utilize current feedback
(CFB) technology to achieve superior performance. The
primary advantage of CFB technology is higher slew rate
performance when compared to voltage feedback (VFB)
architecture. High slew rate contributes directly to better
large signal pulse response, full power bandwidth, and
distortion.
x1
Data Sheet
Application Information
Basic Operation
+Vs
Input
6.8μF
Feedback Resistor Selection
0.1μF
+
Output
-
RL
0.1μF
Rg
Rf
6.8μF
G = 1 + (Rf/Rg)
-Vs
Figure 3. Typical Non-Inverting Gain Circuit
+Vs
R1
Input
0.1μF
+
Rg
6.8μF
Output
-
One of the key design considerations when using a CFB
amplifier is the selection of the feedback resistor, Rf. Rf is
used in conjunction with Rg to set the gain in the traditional non-inverting and inverting circuit configurations.
Refer to figures 3 and 4. As discussed in the Current Feedback Technology section, the value of the feedback resistor has a pronounced effect on the frequency response of
the circuit.
Table 1, provides recommended Rf and associated Rg values for various gain settings. These values produce the
optimum frequency response, maximum bandwidth with
minimum peaking. Adjust these values to optimize performance for a specific application. The typical performance
characteristics section includes plots that illustrate how
the bandwidth is directly affected by the value of Rf at
various gain settings.
RL
0.1μF
Rf
G = - (Rf/Rg)
For optimum input offset
voltage set R1 = Rf || Rg
Rf (Ω)
Rg (Ω)
±0.1dB BW
(MHz)
-3dB BW
(MHz)
1
390
-
136
1300
2
270
270
150
1200
5
270
67.5
115
750
Rev 1A
6.8μF
-Vs
Gain
(V/V
Figure 4. Typical Inverting Gain Circuit
Table 1: Recommended Rf vs. Gain
+Vs
Input
6.8μF
0.1μF
+
Output
0.1μF
6.8μF
-Vs
RL
Rf
G=1
Rf is required for CFB amplifiers
Figure 5. Typical Unity Gain (G=1) Circuit
©2007-2008 CADEKA Microcircuits LLC In general, lowering the value of Rf from the recommended value will extend the bandwidth at the expense
of additional high frequency gain peaking. This will cause
increased overshoot and ringing in the pulse response
characteristics. Reducing Rf too much will eventually
cause oscillatory behavior.
Increasing the value of Rf will lower the bandwidth. Lowering the bandwidth creates a flatter frequency response
and improves 0.1dB bandwidth performance. This is important in applications such as video. Further increase in
Rf will cause premature gain rolloff and adversely affect
gain flatness.
www.cadeka.com
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Figures 3, 4, and 5 illustrate typical circuit configurations for
non-inverting, inverting, and unity gain topologies for dual
supply applications. They show the recommended bypass
capacitor values and overall closed loop gain equations.
CFB amplifiers can be used in unity gain configurations.
Do not use the traditional voltage follower circuit, where
the output is tied directly to the inverting input. With a
CFB amplifier, a feedback resistor of appropriate value
must be used to prevent unstable behavior. Refer to figure 5 and Table 1. Although this seems cumbersome, it
does allow a degree of freedom to adjust the passband
characteristics.
13
Data Sheet
Driving Capacitive Loads
Input
+
Rs
-
Output
CL
Rf
RL
Rg
Overdrive Recovery
An overdrive condition is defined as the point when either
one of the inputs or the output exceed their specified voltage range. Overdrive recovery is the time needed for the
amplifier to return to its normal or linear operating point.
The recovery time varies, based on whether the input or
output is overdriven and by how much the range is exceeded. The CLC1606 Family will typically recover in less
than 10ns from an overdrive condition. Figure 7 shows the
CLC1606 in an overdriven condition.
Figure 6. Addition of RS for Driving
Capacitive Loads
CL (pF)
RS (Ω)
-3dB BW (MHz)
20
20
375
100
10
180
1000
3.3
58
6
VIN = 2Vpp
G=5
1
4
Input Voltage (V)
Input
Output
0.5
2
0
0
-0.5
-2
-1
-4
-1.5
Output Voltage (V)
Table 2 provides the recommended RS for various capacitive loads. The recommended RS values result in <=0.5dB
peaking in the frequency response. The Frequency Response vs. CL plot, on page 5, illustrates the response of
the CLC1606 Family.
1.5
-6
0
20
40
60
80
100
120
140
160
180
200
Time (ns)
Figure 7. Overdrive Recovery
Table 1: Recommended RS vs. CL
Parasitic Capacitance on the Inverting Input
Physical connections between components create unintentional or parasitic resistive, capacitive, and inductive
elements.
Parasitic capacitance at the inverting input can be especially troublesome with high frequency amplifiers. A parasitic capacitance on this node will be in parallel with the
gain setting resistor Rg. At high frequencies, its impedance can begin to raise the system gain by making Rg
appear smaller.
In general, avoid adding any additional parasitic capacitance at this node. In addition, stray capacitance across
the Rf resistor can induce peaking and high frequency
©2007-2008 CADEKA Microcircuits LLC Power dissipation should not be a factor when operating
under the stated 1000 ohm load condition. However, applications with low impedance, DC coupled loads should
be analyzed to ensure that maximum allowed junction
temperature is not exceeded. Guidelines listed below can
be used to verify that the particular application will not
cause the device to operate beyond it’s intended operating range.
Maximum power levels are set by the absolute maximum
junction rating of 150°C. To calculate the junction temperature, the package thermal resistance value ThetaJA
(ӨJA) is used along with the total die power dissipation.
TJunction = TAmbient + (ӨJA × PD)
Where TAmbient is the temperature of the working environment.
www.cadeka.com
14
Rev 1A
For a given load capacitance, adjust RS to optimize the
tradeoff between settling time and bandwidth. In general,
reducing RS will increase bandwidth at the expense of additional overshoot and ringing.
Power Dissipation
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Increased phase delay at the output due to capacitive loading can cause ringing, peaking in the frequency response,
and possible unstable behavior. Use a series resistance,
RS, between the amplifier and the load to help improve
stability and settling performance. Refer to Figure 6.
ringing. Refer to the Layout Considerations section for
additional information regarding high speed layout techniques.
Data Sheet
PD = Psupply - Pload
Psupply = Vsupply × IRMS supply
Vsupply = VS+ - VSPower delivered to a purely resistive load is:
Pload = ((VLOAD)RMS2)/Rloadeff
The effective load resistor (Rloadeff) will need to include
the effect of the feedback network. For instance,
1.5
1
SOIC-8
0.5
SOT23-5
0
-40
-20
0
20
40
60
80
Ambient Temperature (°C)
Figure 8. Maximum Power Derating
Rloadeff in figure 3 would be calculated as:
RL || (Rf + Rg)
These measurements are basic and are relatively easy to
perform with standard lab equipment. For design purposes
however, prior knowledge of actual signal levels and load
impedance is needed to determine the dissipated power.
Here, PD can be found from
PD = PQuiescent + PDynamic - PLoad
Quiescent power can be derived from the specified IS values along with known supply voltage, VSupply. Load power
can be calculated as above with the desired signal amplitudes using:
( ILOAD)RMS = ( VLOAD)RMS / Rloadeff
The dynamic power is focused primarily within the output
stage driving the load. This value can be calculated as:
PDYNAMIC = (VS+ - VLOAD)RMS × ( ILOAD)RMS
In addition, increased airflow across the package can also
help to reduce the effective ӨJA of the package.
In the event the outputs are momentarily shorted to a low
impedance path, internal circuitry and output metallization
are set to limit and handle up to 65mA of output current.
However, extended duration under these conditions may
not guarantee that the maximum junction temperature
(+150°C) is not exceeded.
Layout Considerations
General layout and supply bypassing play major roles in
high frequency performance. CADEKA has evaluation
boards to use as a guide for high frequency layout and as
aid in device testing and characterization. Follow the steps
below as a basis for high frequency layout:
Assuming the load is referenced in the middle of the power
rails or Vsupply/2.
• Include 6.8µF and 0.1µF ceramic capacitors for power
supply decoupling
Figure 8 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 8 and 14 lead
SOIC packages.
• Place the 6.8µF capacitor within 0.75 inches of the power pin
• Place the 0.1µF capacitor within 0.1 inches of the power pin
• Remove the ground plane under and around the part,
especially near the input and output pins to reduce parasitic capacitance
• Minimize all trace lengths to reduce series inductances
Refer to the evaluation board layouts below for more information.
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
15
Rev 1A
(VLOAD)RMS = VPEAK / √2
Better thermal ratings can be achieved by maximizing PC
board metallization at the package pins. However, be careful of stray capacitance on the input pins.
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Supply power is calculated by the standard power equation.
2
Maximum Power Dissipation (W)
In order to determine PD, the power dissipated in the load
needs to be subtracted from the total power delivered by
the supplies.
Data Sheet
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of these devices:
Products
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Evaluation Board #
CEB002
CEB003
CLC1606IST5X
CLC1606ISO8X
Evaluation Board Schematics
Evaluation board schematics and layouts are shown in Figures 9-14. These evaluation boards are built for dual- supply operation. Follow these steps to use the board in a
single-supply application:
1. Short -Vs to ground.
Figure 10. CEB002 Top View
2. Use C3 and C4, if the -VS pin of the amplifier is not
directly connected to the ground plane.
Rev 1A
Figure 11. CEB002 Bottom View
Figure 9. CEB002 Schematic
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
16
Data Sheet
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
Figure 14. CEB003 Bottom View
Figure 12. CEB003 Schematic
Rev 1A
Figure 13. CEB003 Top View
©2007-2008 CADEKA Microcircuits LLC www.cadeka.com
17
Data Sheet
Mechanical Dimensions
SOT23-5 Package
Comlinear CLC1606 1.3GHz Current Feedback Amplifier
SOIC-8 Package
Rev 1A
For additional information regarding our products, please visit CADEKA at: cadeka.com
CADEKA Headquarters Loveland, Colorado
T: 970.663.5452
T: 877.663.5452 (toll free)
CADEKA, the CADEKA logo design, COMLINEAR, the COMLINEAR logo design, and ARCTIC are trademarks or registered trademarks of
CADEKA Microcircuits LLC. All other brand and product names may be trademarks of their respective companies.
CADEKA reserves the right to make changes to any products and services herein at any time without notice. CADEKA does not assume any
responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in
writing by CADEKA; nor does the purchase, lease, or use of a product or service from CADEKA convey a license under any patent rights,
copyrights, trademark rights, or any other of the intellectual property rights of CADEKA or of third parties.
Copyright ©2007-2008 by CADEKA Microcircuits LLC. All rights reserved.
A m p l i fy t h e H u m a n E x p e r i e n c e
Similar pages