Kingbright APHBM2012LCGKSYKC Wide viewing angle Datasheet

2.0x1.25mm SMD CHIP LED LAMP
Part Number: APHBM2012LCGKSYKC
Green
Super Bright Yellow
Features
Descriptions
z 2.0mmx1.25mm SMD LED, 0.45mm max. thickness.
z The Green source color devices are made with AlGaInP
on GaAs substrate Light Emitting Diode.
z Bi -color, low power consumption.
z The Super Bright Yellow device is made with AlGaInP
z Wide viewing angle.
(on GaAs substrate) light emitting diode chip.
z Ideal for backlight and indicator.
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z Low current IF=2mA operating.
z RoHS compliant.
Package Dimensions
GREEN
GREEN
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAO4525
REV NO: V.1B
DATE: AUG/01/2015
PAGE: 1 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015149
Selection Guide
Part No.
Emitting Color (Material)
APHBM2012LCGKSYKC
Iv (mcd) [2]
@ 2mA
Lens Type
Green (AlGaInP)
Water Clear
Super Bright Yellow (AlGaInP)
Min.
Typ.
1.2
2
6
10
Viewing
Angle [1]
2θ1/2
120°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Min.
Symbol
Parameter
Emitting Color
λpeak
Peak Wavelength
Green
Super Bright Yellow
λD [1]
Dominant Wavelength
Δλ1/2
Units
Test Conditions
574
590
nm
IF=2mA
Green
Super Bright Yellow
570
590
nm
IF=2mA
Spectral Line Half-width
Green
Super Bright Yellow
20
20
nm
IF=2mA
C
Capacitance
Green
Super Bright Yellow
15
20
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Green
Super Bright Yellow
2.1
2.1
V
IF=2mA
IR
Reverse Current
Green
Super Bright Yellow
10
10
uA
VR = 5V
1.5
1.5
Typ.
Max.
1.9
1.85
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Green
Super Bright Yellow
Units
Power dissipation
63
63
mW
DC Forward Current
30
30
mA
Peak Forward Current [1]
150
175
mA
Reverse Voltage
5
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
V
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAO4525
REV NO: V.1B
DATE: AUG/01/2015
PAGE: 2 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015149
APHBM2012LCGKSYKC
Green
SPEC NO: DSAO4525
REV NO: V.1B
DATE: AUG/01/2015
PAGE: 3 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015149
Super Bright Yellow
SPEC NO: DSAO4525
REV NO: V.1B
DATE: AUG/01/2015
PAGE: 4 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015149
APHBM2012LCGKSYKC
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAO4525
REV NO: V.1B
DATE: AUG/01/2015
PAGE: 5 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015149
PACKING & LABEL SPECIFICATIONS
APHBM2012LCGKSYKC
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAO4525
REV NO: V.1B
DATE: AUG/01/2015
PAGE: 6 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015149
Similar pages