NSC DS36C280TN Slew rate controlled cmos eia-rs-485 transceiver Datasheet

DS36C280
Slew Rate Controlled CMOS EIA-RS-485 Transceiver
General Description
Features
The DS36C280 is a low power differential bus/line transceiver designed to meet the requirements of RS-485 Standard for multipoint data transmission. In addition, it is compatible with TIA/EIA-422-B.
The slew rate control feature allows the user to set the driver
rise and fall times by using an external resistor. Controlled
edge rates can reduce switching EMI.
n 100% RS-485 compliant
— Guaranteed RS-485 device interoperation
n Low power CMOS design: ICC 500 µA max
n Adjustable slew rate control
— Minimizes EMI affects
n Built-in power up/down glitch-free circuitry
— Permits live transceiver insertion/displacement
n DIP and SOIC packages available
n Industrial temperature range: −40˚C to +85˚C
n On-board thermal shutdown circuitry
— Prevents damage to the device in the event of
excessive power dissipation
n Wide common mode range: −7V to +12V
n Receiver open input fail-safe (Note 1)
n 1⁄4 unit load (DS36C280): ≥128 nodes
n 1⁄2 unit load (DS36C280T): ≥64 nodes
n ESD (human body model): ≥2 kV
The CMOS design offers significant power savings over its
bipolar and ALS counterparts without sacrificing ruggedness
against ESD damage. The device is ideal for use in battery
powered or power conscious applications. ICC is specified at
500 µA maximum.
The driver and receiver outputs feature TRI-STATE ® capability. The driver outputs operate over the entire common mode
range of −7V to +12V. Bus contention or fault situations are
handled by a thermal shutdown circuit, which forces the
driver outputs into the high impedance state.
The receiver incorporates a fail safe circuit which guarantees
a high output state when the inputs are left open (Note 1) .
Connection and Logic Diagram
Truth Table
DRIVER SECTION
DE/RE*
DI
DO/RI
H
H
H
DO*/RI*
L
H
L
L
H
L
X
Z
Z
RECEIVER SECTION
DS012052-1
Order Number DS36C280TM, DS36C280TN
DS36C280M and DS36C280N
See NS Package Number M08A or N08E
DE/RE*
RI-RI*
RO
L
≥+0.2V
H
L
≤−0.2V
L
H
X
Z
L
OPEN (Note 1)
H
Note 1: Non-terminated, Open Inputs only
TRI-STATE ® is a registered trademark of National Semiconductor Corporation.
© 1999 National Semiconductor Corporation
DS012052
www.national.com
DS36C280 Slew Rate Controlled CMOS EIA-RS-485 Transceiver
July 1998
Absolute Maximum Ratings (Note 2)
Storage Temperature Range
Lead Temperature
(Soldering 4 sec.)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
−65˚C to +150˚C
+260˚C
Recommended Operating
Conditions
Supply Voltage (VCC)
+12V
Input Voltage (DE/RE*, & DI)
−0.5V to (VCC +0.5V)
Common Mode (VCM)
± 15V
Driver Output/Receiver Input
± 14V
Input Voltage (DO/RI, DO*/RI*)
Receiver Output Voltage
−0.5V to (VCC +0.5V)
Maximum Package Power Dissipation @ +25˚C
M Package 1190 mV, derate
9.5 mW/˚C above +25˚C
N Package 794 mV, derate
6.0 mW/˚C above +25˚C
Min
+4.75
Supply Voltage (VCC)
Bus Voltage
−7
Operating Free Air Temperature (TA)
DS36C280T
−40
DS36C280
0
Typ
+5.0
Max
+5.25
+12
Units
V
V
+25
+25
+85
+70
˚C
˚C
Electrical Characteristics (Notes 3, 4)
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified
Symbol
Parameter
Conditions
Reference
Min
Typ
Max
Units
1.5
5.0
V
0
5.0
V
0
5.0
V
DIFFERENTIAL DRIVER CHARACTERISTICS
VOD1
Differential Output Voltage
IO = 0 mA (No Load)
VOD0
Output Voltage
IO = 0 mA
VOD0*
Output Voltage
(Output to GND)
VOD2
Differential Output Voltage
(Termination Load)
RL = 50Ω
(422)
RL = 27Ω
(485)
Balance of VOD2
RL = 27Ω or 50Ω
∆VOD2
(422)
(485)
(Note 5)
|VOD2 − VOD2*|
VOD3
VOC
∆VOC
IOSD
Figure 1
2.0
2.8
1.5
2.3
5.0
V
V
−0.2
0.1
+0.2
V
1.5
2.0
5.0
V
0
3.0
V
0
3.0
V
−0.2
+0.2
V
(422, 485)
Figure 2
Differential Output Voltage
(Full Load)
VTEST = −7V to +12V
R1 = 54Ω, R2 = 375Ω
Driver Common Mode
Output Voltage
RL = 27Ω
(485)
RL = 50Ω
(422)
Balance of VOC
RL = 27Ω or
Figure 1
(Note 5)
|VOC − VOC*|
RL = 50Ω
Driver Output Short-Circuit
Current
VO = +12V
(485) Figure 4
200
+250
mA
VO = −7V
(485)
−190
−250
mA
+0.035
+0.2
V
(422, 485)
RECEIVER CHARACTERISTICS
VTH
VTL
Differential Input High
Threshold Voltage
−7V ≤ VCM ≤ +12V
VO = VOH, IO = −0.4 mA
Differential Input Low
Threshold Voltage
−7V ≤ VCM ≤ +12V
(Note 6)
(422, 485)
VO = VOL, IO = 0.4 mA
−0.2 −0.035
V
VHST
Hysteresis
VCM = 0V
70
mV
RIN
Input Resistance
−7V ≤ VCM ≤ +12V
DS36C280T
24
68
kΩ
RIN
Input Resistance
−7V ≤ VCM ≤ +12V
DS36C280
48
68
IIN
Line Input Current
(Note 8)
Other Input = 0V
VIN = +12V
0
0.19
0.25
mA
VIN = −7V
0
−0.1
−0.2
mA
VIN = +12V
0
0.19
0.5
mA
VIN = −7V
0
−0.1
−0.4
mA
DS36C280
DE = VIL, RE* = VIL
VCC = 4.75 to 5.25
DS36C280T
or 0V
IING
Line Input Current
Glitch (Note 8)
Other Input = 0V
DS36C280
DE = VIL, RE* = VIL
VCC = +3.0V
DS36C280T
or 0V TA = 25˚C
IB
Input Balance Test
RS = 500Ω
VOH
High Level Output Voltage
IOH = −4 mA, VID = +0.2V
VOL
Low Level Output Voltage
IOL = +4 mA, VID = −0.2V
www.national.com
VIN = +12V
0
0.19
0.25
mA
VIN = −7V
0
−0.1
−0.2
mA
VIN = +12V
0
0.19
0.5
mA
VIN = −7V
0
−0.1
−0.4
mA
± 400
mV
3.5
4.6
(422) (Note 10)
2
kΩ
RO
Figure 11
0.3
V
0.5
V
Electrical Characteristics (Notes 3, 4)
(Continued)
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified
Symbol
Parameter
Conditions
Reference
Min
Typ
RO
7
35
Max
Units
RECEIVER CHARACTERISTICS
IOSR
Short Circuit Current
VO = GND
IOZR
TRI-STATE Leakage
Current
VO = 0.4V to 2.4V
85
mA
±1
µA
V
DEVICE CHARACTERISTICS
VIH
High Level Input Voltage
2.0
VCC
VIL
Low Level Input Voltage
GND
0.8
V
IIH
High Level Input Current
2
µA
IIL
Low Level Input Current
−2
µA
DE/RE*,
DI
VIH = VCC
VCC = 5.0V
VIL = 0V
VCC = +3.0V
SR = 0V
ICCR
ICCD
Power Supply Current
(No Load)
−2
µA
−1
mA
200
500
µA
200
500
µA
SR
Driver OFF, Receiver ON
VCC
Driver ON, Receiver OFF
Switching Characteristics (Notes 4, 9, 11)
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified
Symbol
Parameter
Conditions
Reference
Min
Typ
Max
Units
RL = 54Ω, CL = 100 pF
Figures 5, 6
10
399
1000
ns
DRIVER CHARACTERISTICS
tPHLD
Differential Propagation
Delay High to Low
tPLHD
Differential Propagation
Delay Low to High
10
400
1000
ns
tSKD
Differential Skew
0
1
10
ns
|tPHLD − tPLHD|
tr
Rise Time
tf
Fall Time
tr
Rise Time
tf
Fall Time
tr
Rise Time
tf
Fall Time
tPHZ
Disable Time High to Z
tPLZ
Disable Time Low to Z
tPZH
Enable Time Z to High
tPZL
Enable Time Z to Low
SR = Open
2870
SR = 100 kΩ
ns
3070
ns
1590
ns
1640
SR = Short
100
100
CL = 15 pF
CL = 100 pF
337
ns
1000
ns
348
1000
ns
Figures 7, 8
1100
2000
ns
Figures 9, 10
500
800
ns
Figures 7, 8
300
500
ns
Figures 9, 10
300
500
ns
30
210
400
ns
30
190
400
ns
RECEIVER CHARACTERISTICS
tPHL
Propagation Delay
High to Low
tPLH
Propagation Delay
Low to High
tSK
Skew, |tPHL − tPLH|
tPLZ
Output Disable Time
CL = 15 pF
Figures 12, 13
0
CL = 15 pF
tPHZ
tPZL
Figures 14, 15, 16
Output Enable Time
tPZH
20
50
ns
50
150
ns
55
150
ns
40
150
ns
45
150
ns
Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD1 and VOD2.
Note 4: All typicals are given for: VCC = +5.0V, TA = + 25˚C.
Note 5: Delta |VOD2| and Delta |VOC| are changes in magnitude of VOD2 and VOC, respectively, that occur when input changes state.
3
www.national.com
Switching Characteristics (Notes 4, 9, 11)
(Continued)
Note 6: Threshold parameter limits specified as an algebraic value rather than by magnitude.
Note 7: Hysteresis defined as VHST = VTH − VTL.
Note 8: IIN includes the receiver input current and driver TRI-STATE leakage current.
Note 9: CL includes probe and jig capacitance.
Note 10: For complete details of test, see RS-485.
Note 11: SR = GND for all Switching Characteristics unless otherwise specified.
Parameter Measurement Information
DS012052-2
FIGURE 1. Driver VOD2 and VOC
DS012052-5
FIGURE 5. Driver Differential
Propagation Delay Test Circuit
DS012052-18
FIGURE 2. Driver VOD3
DS012052-3
FIGURE 3. Driver VOH and VOL
DS012052-6
FIGURE 6. Driver Differential Propagation Delays
and Differential Rise and Fall Times
DS012052-4
Vtest = −7V to +12V
FIGURE 4. Driver IOSD
DS012052-7
FIGURE 7. TRI-STATE Test Circuit (tPZH , tPHZ)
www.national.com
4
Parameter Measurement
Information (Continued)
DS012052-10
FIGURE 10. TRI-STATE Waveforms (tPZL, tPLZ)
DS012052-8
FIGURE 8. TRI-STATE Waveforms (tPZH, tPHZ)
DS012052-11
FIGURE 11. Receiver VOH and VOL
DS012052-9
FIGURE 9. TRI-STATE Test Circuit (tPZL, tPLZ)
DS012052-12
FIGURE 12. Receiver Differential
Propagation Delay Test Circuit
DS012052-13
FIGURE 13. Receiver Differential Propagation Delay Waveforms
DS012052-14
FIGURE 14. Receiver TRI-STATE Test Circuit
5
www.national.com
Parameter Measurement Information
(Continued)
DS012052-15
FIGURE 15. Receiver Enable and Disable Waveforms (tPLZ, tPZL)
DS012052-16
FIGURE 16. Receiver Enable and Disable Waveforms (tPHZ, tPZH)
Typical Application Information
DS012052-17
FIGURE 17. Typical Pin Connection
TABLE 1. Device Pin Descriptions
Pin
#
Name
Description
1
RO
Receiver Output: When DE/RE* (Receiver Enable) is LOW, the receiver is enabled (ON), if DO/RI ≥
DO*/RI* by 200 mV, RO will be HIGH. If DO/RI ≤ DO*/RI* by 200 mV, RO will be LOW. Additionally RO
will be HIGH for OPEN (Non-terminated) inputs.
2
SR
Slew Rate Control: A resistor connected to Ground controls the Driver Output rising and falling edge
rates.
3
DE/RE*
Combined Driver and Receiver Output Enable: When signal is LOW the receiver output is enabled and
the driver outputs are in TRI-STATE (OFF). When signaI is HlGH, the receiver output is in TRI-STATE
(OFF) and the driver outputs are enabled.
4
DI
Driver Input: When DE/RE* is HlGH, the driver is enabled, if DI is LOW, then DO/RI will be LOW and
DO*/RI* will be HIGH. If DI is HIGH, then DO/RI is HIGH and DO*/RI* is LOW.
www.national.com
6
Typical Application Information
(Continued)
TABLE 1. Device Pin Descriptions (Continued)
Pin
#
Name
Description
5
GND
6
DO/RI
Ground Connection
Driver Output/Receiver Input, 485 Bus Pin.
7
DO*/RI*
Driver Output/Receiver Input, 485 Bus Pin.
8
VCC
Positive Power Supply Connection: Recommended operating range for VCC is +4.75V to +5.25V.
DS36C280 has a slew rate control for EMI conscious applications. Refer to the sleep mode and slew rate control portion of the application information section in the corresponding datasheet for more information on these features.
Unit Load
A unit load for a RS-485 receiver is defined by the input current versus the input voltage curve. The gray shaded region
is the defined operating range from −7V to +12V. The top
border extending from −3V at 0 mA to +12V at +1 mA is defined as one unit load. Likewise, the bottom border extending
from +5V at 0 mA to −7V at −0.8 mA is also defined as one
unit load (see Figure 18 ). A RS-485 driver is capable of driving up to 32 unit loads. This allows upto 32 nodes on a single
bus. Although sufficient for many applications, it is sometime
desirable to have even more nodes. For example an aircraft
that has 32 rows with 4 seats per row could benefit from having 128 nodes on one bus. This would allow signals to be
transferred to and from each individual seat to 1 main station. Usually there is one or two less seats in the last row of
the aircraft near the restrooms and food storage area. This
frees the node for the main station.
The DS36C278, the DS36C279, and the DS36C280 all have
1⁄2 unit load and 1⁄4 unit load (UL) options available. These
devices will allow upto 64 nodes or 128 nodes guaranteed
over temperature depending upon which option is selected.
The 1⁄2 UL option is available in industrial temperature and
the 1⁄4 UL is available in commercial temperature.
First, for a 1⁄2 UL device the top and bottom borders shown in
Figure 18 are scaled. Both 0 mA reference points at +5V and
−3V stay the same. The other reference points are +12V at
+0.5 mA for the top border and −7V at −0.4 mA for the bottom border (see Figure 18 ). Second, for a 1⁄4 UL device the
top and bottom borders shown in Figure 18 are scaled also.
Again, both 0 mA reference points at +5V and −3V stay the
same. The other reference points are +12V at +0.25 mA for
the top border and −7V at −0.2 mA for the bottom border
(see Figure 18 ).
The advantage of the 1⁄2 UL and 1⁄4 UL devices is the increased number of nodes on one bus. In a single master
multi-slave type of application were the number of slaves exceeds 32, the DS36C278/279/280 may save in the cost of
extra devices like repeaters, extra media like cable, and/or
extra components like resistors.
The DS36C279 and DS36C280 have addition feature which
offer more advantages. The DS36C279 has an automatic
sleep mode function for power conscious applications. The
DS012052-19
FIGURE 18. Input Current vs Input Voltage
Operating Range
Slew Rate Control
The DS36C280 features an adjustable slew rate control.
This feature allows more control over EMl levels than tradition fixed edge rate devices. The slew rate control may be
adjusted with or without any external components. The
DS36C280 offers both low power (ICC 500 µA max) and low
EMI for an RS-485 interface.
The slew rate control is located at pin two of the device and
only controls the driver output edges. The slew rate control
pin (SR) may be left open or shorted to ground, with or without a resistor. When the SR pin is shorted to ground without
a resistor, the driver output edges will transition typically
350 ns. When the SR pin is left open, the driver output edges
will transition typically 3 µs. When the SR pin is shorted to
ground with a resistor, the driver output edges will transition
between 350 ns and 3 µs depending on the resistor value.
Refer to the slew rate versus resistor value curve in this
datasheet for determining resistor values and expected typical slew rate value. Please note, when slowing the edge
rates of the device (see Figure 19 ) will decrease the maximum data rate also.
7
www.national.com
Slew Rate Control
(Continued)
Differential Rise/Fall Time
vs Slew Rate Resistor
DS012052-20
FIGURE 19. Slew Rate Resistor
vs Rise/Fall Time
www.national.com
8
Physical Dimensions
inches (millimeters) unless otherwise noted
8-Lead (0.150" Wide) Molded Small Outline Package, JEDEC
Order Number DS36C280TM
NS Package Number M08A
8-Lead (0.300" Wide) Molded Dual-In-Line Package
Order Number DS36C280TN
NS Package Number N08E
9
www.national.com
DS36C280 Slew Rate Controlled CMOS EIA-RS-485 Transceiver
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component is any component of a life support
1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into
sonably expected to cause the failure of the life support
the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness.
ure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages