Bel A477-0100-06 1 tap leading edge control low voltage delay module Datasheet

defining a degree of excellence
1 TAP LEADING EDGE CONTROL
LOW VOLTAGE DELAY MODULES
Cat 35 -R0
.60 + .02
.375
.350
.60 + .02
8 Out
bel
(DC )
(P/N)
.285 Max
.80 Max
Vcc 14
In 1
Gnd 7
4
Coplanarity + .002
.030
.012
.008
100o
90o
Part Numbers
S477-0010-06
S477-0020-06
S477-0030-06
S477-0040-06
S477-0050-06
A477-0010-06
A477-0020-06
A477-0030-06
A477-0040-06
A477-0050-06
S477-0060-06
S477-0070-06
S477-0080-06
S477-0090-06
A477-0060-06
A477-0070-06
A477-0080-06
A477-0090-06
10
20
30
40
50
60
70
80
90
ns
ns
ns
ns
ns
ns
ns
ns
ns
S477-0100-06 A477-0100-06 100 ns
S477-0125-06 A477-0125-06 125 ns
S477-0150-06 A477-0150-06 150 ns
S477-0200-06 A477-0200-06 200 ns
Rise
Time
Tolerance
+
+
+
+
+
2.0
2.0
2.0
2.0
2.5
ns
ns
ns
ns
ns
3
3
3
3
3
ns
ns
ns
ns
ns
+ 3.0 ns
+ 3.5 ns
+ 4.0 ns
+ 4.5 ns
+ 5.0 ns
+ 6.3 ns
+ 7.5 ns
+ 10.0 ns
3
3
3
3
ns
ns
ns
ns
3 ns
3 ns
3 ns
3 ns
Input to Output + 2 ns or 5% , Whichever is Greater
Delays measured @ 50% levels on Leading Edge only
wth no loads on Output
Rise and Fall Times measured from 10% to 90% levels
Drive Capabilities
-
Infra Red
200 C
Temp.
100o C
0
2
4
6
Time in Minutes
Pulse Voltage
Rise Time
Pulse Width
Pulse Period
Supply Current
Supply Voltage
3.0 Volts
3.0 ns (10%-90%)
1.2 x Total Delay
4 x Pulse Width
25 ma Typical
5.0 Volts
Electrical Characteristics
Min.
3.0
2.4
Max.
3.6
Units
V
V
V
ma
ma
ma
V
V
V
ua
ua
ma
ma
C
%
%
Vcc
Vih
Vil
Iik
Ioh
Iol
Voh
Vol
Vik
Iih
Iil
Icch
Iccl
Ta
PW
d
Supply Voltage
Logic 1 Input Voltage
Logic 0 Input Voltage
Input Clamp Current
Logic 1 Output Current
Logic 0 Output Current
Logic 1 Output Voltage
Logic 0 Output voltage
Input Clamp Voltage
Logic 1 Input Current
Logic 0 Input Current
Logic 1 Supply Current
Logic 0 Supply Current
Operating Free Air Temperature
Min. Input Pulse Width of Total Delay
Maximum Duty Cycle
Tc
Temp. Coeff. of Total Delay (TD) 100 + (25000/TD) PPM/OC
0.8
-20
20
-20
2.9
0o
40
0.1
-0.5
1
-1
10
30
70o
50
Notes
Transfer molded for better reliability
Compatible with TTL & DTL circuits
Terminals: Electro-Tin plate phosphor bronze
Performance warranty is limited to specified parameters listed
SMD - Tape & Reel available:
32mm Wide x 16mm Pitch, 500 pieces per 13" reel
225o C Max Temp.
> 185o C
for 90 Seconds Max
o
Ein
Trin
PW
PP
Iccl
Vcc
10 LSTTL Loads Max.
10 LSTTL Loads Max.
Recommended Temperature Profile
300o C
.015 Min
.045
.018
.12 Min
Test Conditions @ 25oC
Tolerances
Nh Logic 1 Fanout
Nl Logic 0 Fanout
.20 Max
.23 Max
.012
.008
Time
Delay
.285 Max
o
.018
Thru-Hole
(DC)
(P/N)
.80 Max
.015
.004
.22 Max
SMD
bel
.325
*
8
Other Delays and Tolerances Available
Consult Sales
Specifications subject to change without notice.
Corporate Office
Bel Fuse Inc.
198 Van Vorst Street, Jersey City, NJ 07302-4496
Tel: 201-432-0463
Fax: 201-432-9542
E-Mail: [email protected]
Internet: http://www.belfuse.com
Far East Office
Bel Fuse Ltd.
8F/8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel: 852-2328-5515
Fax: 852-2352-3706
European Office
Bel Fuse Europe Ltd.
Preston Technology Management Centre
Marsh Lane, Preston PR1 8UD
Lancashire, U.K.
Tel: 44-1772-556601
Fax: 44-1772-888366
23
Similar pages