EPCOS B44020J0006B012 Accessories for capacitors with mounting stud on capacitor base Datasheet

B44020
Accessories
KAL0567 B
Accessories
Accessories for capacitors with mounting stud on capacitor base
Capacitor
diameter
Dimensional drawing
Diameter
d (mm)
Ordering code
Insulating plastic shoulder washer “P” similar to DIN 41 331 specifications
for M 8 thread
≤ 40 mm
8,4
B44020B0001B025
12,5
B44020B0002B030
KAL0216-I
for M 12 thread
> 40 mm
KAL0059-P
Insulating washer “N” made of laminated paper
for M 8 / M 12 thread
≤ 40 mm
> 40 mm
8,4
B44020A0001B025
13,0
B44020A0002B025
KAL0066-7
Insulating washer made of Hostalen
d 1 – 0,5 d 2 – 0,5
51,6 mm
51
31
B44020B0006B051
76,9 mm
76
56
B44020B0006B076
KAL0061-1
166 10/02
B44020
Accessories
KAL0567 B
Capacitor
diameter
Dimensional drawing
Ordering code
Plastic cap nut “V”
for M 8 thread
width across flats 13 mm
≤ 40 mm
B44020B0005B008
KAL0067-F
for M 12 thread
width across flats 17 mm
> 40 mm
B44020A0005B012
KAL0068-N
Reinforced nylon cap nut
for M 12 thread
width across flats 19 mm
> 40 mm
B44020J0006B012
for M 8 thread
width across flats 17 mm
≤ 40 mm
B44020J0006B008
KAL0236-X
thread *)
for M 12
width across flats 19 mm
> 40 mm
B44020J0007B012
KAL0285-Q
*) For achieving larger clearances.
167 10/02
B44020
Accessories
KAL0567 B
Mounting instructions
Maximum tightening torques:
Thread
Maximum torque
M8
M12
4
10
Nm
Nm
Non-insulated mounting
with cap nut
KAL0063-H
Insulated mounting
with cap nut
KAL0064-Q
Mounting hole diameter
Insulated mounting with DIN 439 hex nut
d ≤ 76,9 mm
d = 91 mm
KAL0065-Y
Mounting hole diameter
Mounting hole diameter
168 10/02
B44030
Accessories
KAL0567 B
Ring clip mounting
Ring clips are primarily used for upright mounting of screw-terminal and photoflash capacitors. The
clip surfaces are specially treated and corrosion-protected.
dN
Capacitor
Mounting plate
KAL0193-A
A variety of ring clip versions is available for Al electrolytic capacitors. Some versions are supplied
with AM 3 × 10 DIN 84 clamping screws and DIN 934 nuts included. Additional insulation can be
achieved by inserting a 30 mm-wide insulating strip between the capacitor and the ring clip. In such
cases, attention must be paid to any relevant regulations (e. g. VDE, BSA or UL regulations).
dN
h1
h2
Ring clip version
mm
25
19
Ordering code
without
with
insulating strip
B44030A0025B
15
B44030J0025B
KAL0198-G
(insulating strip
length:175mm)
Clamping screws and nuts are
included in delivery package.
30
19
B44030A0030B
15
B44030J0030B
KAL0199-P
Clamping screws and nuts are
included in delivery package.
169 10/02
(insulating strip
length: 200mm)
B44030
Accessories
KAL0567 B
dN
h1
h2
Ring clip version
mm
19
Ordering code
without
with
insulating strip
B44030A0035B
15
B44030J0035B
KAL0201-5
(insulating strip
length: 230mm)
Clamping screws and nuts are
included in delivery package.
35
15
B44030A0036B
10
B44030J0036B
(insulating strip
length: 230mm)
40
19
B44030A0040B
15
B44030J0040B
KAL0200-W
Clamping screws and nuts are
included in delivery package.
170 10/02
(insulating strip
length: 260mm)
B44030
Accessories
KAL0567 B
dN
h1
h2
Ring clip version
mm
19
Ordering code
without
with
insulating strip
B44030A0050B
15
B44030J0050B
KAL0194-I
(insulating strip
length: 325mm)
Clamping screws and nuts are
included in delivery package.
50
22
B44030A0051B
15
B44030J0051B
(insulating strip
length: 325mm)
65
26
B44030A0065B
22
B44030J0065B
KAL0203-L
Clamping screws and nuts are
included in delivery package.
171 10/02
(insulating strip
length: 420mm)
B44030
Accessories
KAL0567 B
dN
h1
h2
Ring clip version
mm
65
29
Ordering code
without
with
insulating strip
B44030A0064B
19
B44030J0064B
(insulating strip
length: 420mm)
75
29
B44030A0075B
19
B44030J0075B
(insulating strip
length: 495mm)
90
29
19
B44030A0090B
B44030J0090B
(insulating strip
length: 585mm)
172 10/02
B44030
Accessories
KAL0567 B
Clamp mounting
Screw-terminal capacitors without threaded stud and with a diameter ≥ 64,3 mm can also be mounted with clamps.
Clamp mounting offers the following advantages:
■ Optimum heat transfer between capacitor base and board due to pressure contact
■ High vibration resistance
■ Electrically insulated material
Dimensional drawing
Section A-B
dN
Capacitor
Fixing part
Untightened
Cylinder screw
DIN912-M6x…
Board
Tubular
rivet 3)
Tightened
Dimensions and ordering codes
Capacitor
diameter dN
d1 ± 0,2
mm
b
mm
Ordering code
B44030A0165B
65 mm
87
104
75 mm
99
116
B44030A0175B
90 mm
112
130
B44030A0190B
Screws are not included in the delivery package.
1) Lenght depends on application.
2) The screws have to be tightened uniformly and crosswise until the fixing part rests flatly on the board.
3) Tubular rivets included in delivery package.
173 10/02
B44030
Accessories
KAL0567 B
Mounting set (clamping rings)
This mounting set offers following advantages:
–
–
–
–
Protects the capacitor against tilt
Fits for different capacitor length
Protects the capacitor terminals from mechanical stress
Electrically insulated clamping material
Dimensional drawing
12
45,5
86
80
10
ø101
ø90
43,5
ø86
ø75
ø83
12
0˚
63.5
57,5
ø5
ø6
ø95,5
105
120
Clamping ring
Dimensions and ordering codes
Mounting base plate
Capacitor
diameter d N
75 mm
ø min.
KAL0499-8
90 mm
174 10/02
∅min
mm
KAL0499-8 84
96,5
Ordering code
B44030A0375B
B44030A0390B
Herausgegeben von EPCOS AG
Unternehmenskommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND
++49 89 636 09, FAX (0 89) 636-2 26 89
(
 EPCOS AG 2002. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet.
Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird.
Diese Broschüre ersetzt die vorige Ausgabe.
Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG
oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen.
Published by EPCOS AG
Corporate Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY
++49 89 636 09, FAX (0 89) 636-2 26 89
(
 EPCOS AG 2002. Reproduction, publication and dissemination of this brochure and the information contained therein without
EPCOS’ prior express consent is prohibited.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics
Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed.
This brochure replaces the previous edition.
For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives.
Due to technical requirements components may contain dangerous substances. For information on the type in question please
also contact one of our Sales Offices.
Similar pages