Anpec APL5320-20QF Ultra-low-noise, high psrr, low-dropout, 300ma linear regulator Datasheet

APL5320
Ultra-Low-Noise, High PSRR, Low-Dropout, 300mA Linear Regulator
Features
General Description
•
Wide Operating Voltage: 2.5~6V
•
Low Dropout Voltage: 290mV @ 3V/300mA
The APL5320 is a P-channel low dropout linear regulator
which needs only one input voltage from 2.5 to 6V, and
•
Fixed Output Voltages: 1.2~3.7V with Step 100mV,
delivers current up to 300mA to set output voltage. It also
can work with low ESR ceramic capacitors and is ideal for
and 2.85V, 4.75V
using in the battery-powered applications such as notebook computers and cellular phones. Typical dropout volt-
•
Guaranteed 300mA Output Current
•
High PSRR: 70dB
•
Current-Limit Protection
•
Controlled Short-Circuit Current: 50mA
•
Over-Temperature Protection
•
Stable with 1µF Capacitor for Any Load
•
Excellent Load/Line Transient
•
SOT-23-5, TSOT-23-5, SOT-23-3, SC-70-5,
age is only 290mV at 300mA loading.
The APL5320 provides several versions of fixed output
voltages ranging from 1.2 to 3.7V with step 100mV and
2.85V, 4.75V. Current-limit with current foldback and thermal shutdown functions protects the device against current over-loads and over-temperature. The APL5320 is
available in SOT-23-5, TSOT-23-5, SOT-23-3, SC-70-5,
VTDFN1.2x1.6-4, and TDFN 1.6x1.6-6 packages.
VTDFN1.2x1.6-4, and TDFN1.6x1.6-6 Packages
•
Lead Free and Green Devices Available
Pin Configuration
(RoHS Compliant)
Applications
VIN 1
GND 2
SHDN 3
•
Cellular Phones
•
Portable and Battery-Powered Equipments
•
Laptops, Palmtops, Notebook Computers
•
Wireless LANs
•
Portable Information Appliances
•
GPSes
5 VOUT
4 NC
SOT23-5/TSOT-23-5/SC-70-5
(Top View)
GND 1
3 VIN
VOUT 2
SOT-23-3
(Top View)
Simplified Application Circuit
VOUT 1
VIN
VIN
VOUT
VOUT
GND 2
SHDN
GND
4 VIN
3 SHDN
VTDFN1.2x1.6-4
(Top View)
Enable
SHDN 1
NC 2
VIN 3
6 GND
5 NC
4 VOUT
TDFN1.6x1.6-6
(Top View)
= Exposed Pad (connected to ground
plane for better heat dissipation)
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and
advise customers to obtain the latest version of relevant information to verify before placing orders.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
1
www.anpec.com.tw
APL5320
Ordering and Marking Information
APL5320
Package Code
B : SOT-23-5 BT : TSOT-23-5 A : SOT-23-3
S5 : SC-70-5 QB : TDFN1.6x1.6-6 QF: VTDFN1.2x1.6-4
Operating Ambient Temperature Range
I : -40 to 85 oC
Handling Code
TR : Tape & Reel
Voltage Code
12 : 1.2V 36 : 3.6V
Assembly Material
G : Halogen and Lead Free Device
Assembly Material
Handling Code
Temperature Range
Package Code
Voltage Code
Note : ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which
are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for
MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant)and halogen
free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by
weight).
SOT-23-5
Product Name
Marking
Product Name
Marking
Product Name
Marking
Product Name
Marking
APL5320-12B
APL5320-16B
APL5320-20B
APL5320-24B
APL5320-28B
APL5320-32B
APL5320-36B
205X
20AX
20EX
20IX
20MX
20QX
20gX
APL5320-13B
APL5320-17B
APL5320-21B
APL5320-25B
APL5320-29B
APL5320-33B
APL5320-285B
207X
20BX
20FX
20JX
20NX
20RX
20dX
APL5320-14B
APL5320-18B
APL5320-22B
APL5320-26B
APL5320-30B
APL5320-34B
APL5320-37B
208X
20CX
20GX
20KX
20OX
20SX
206X
APL5320-15B
APL5320-19B
APL5320-23B
APL5320-27B
APL5320-31B
APL5320-35B
APL5320-475B
209X
20DX
20HX
20LX
20PX
20TX
204X
Product Name
Marking
Product Name
Marking
Product Name
Marking
Product Name
Marking
APL5320-12BT
APL5320-16BT
APL5320-20BT
APL5320-24BT
APL5320-28BT
APL5320-32BT
APL5320-36BT
205X
20AX
20EX
20IX
20MX
20QX
20gX
APL5320-13BT
APL5320-17BT
APL5320-21BT
APL5320-25BT
APL5320-29BT
APL5320-33BT
APL5320-285BT
207X
20BX
20FX
20JX
20NX
20RX
20dX
APL5320-14BT
APL5320-18BT
APL5320-22BT
APL5320-26BT
APL5320-30BT
APL5320-34BT
APL5320-37BT
208X
20CX
20GX
20KX
20OX
20SX
206X
APL5320-15BT
APL5320-19BT
APL5320-23BT
APL5320-27BT
APL5320-31BT
APL5320-35BT
APL5320-475BT
209X
20DX
20HX
20LX
20PX
20TX
204X
Product Name
Marking
Product Name
Marking
Product Name
Marking
Product Name
Marking
APL5320-12A
APL5320-16A
APL5320-20A
APL5320-24A
APL5320-28A
APL5320-32A
APL5320-36A
205X
20AX
20EX
20IX
20MX
20QX
20gX
APL5320-13A
APL5320-17A
APL5320-21A
APL5320-25A
APL5320-29A
APL5320-33A
APL5320-285A
207X
20BX
20FX
20JX
20NX
20RX
20dX
APL5320-14A
APL5320-18A
APL5320-22A
APL5320-26A
APL5320-30A
APL5320-34A
APL5320-37A
208X
20CX
20GX
20KX
20OX
20SX
206X
APL5320-15A
APL5320-19A
APL5320-23A
APL5320-27A
APL5320-31A
APL5320-35A
APL5320-475A
209X
20DX
20HX
20LX
20PX
20TX
204X
Note: X - Code.
TSOT-23-5
Note: X - Code.
SOT-23-3
Note: X - Code.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
2
www.anpec.com.tw
APL5320
Ordering and Marking Information (Cont.)
TDFN1.6x1.6-6
Product Name
APL5320-12QB
APL5320-16QB
APL5320-20QB
APL5320-24QB
APL5320-28QB
APL5320-32QB
APL5320-36QB
Marking
205
X
20A
X
20E
X
20I
X
20M
X
20Q
X
20g
X
Product Name
APL5320-13QB
APL5320-17QB
APL5320-21QB
APL5320-25QB
APL5320-29QB
APL5320-33QB
APL5320-285QB
Marking
Product Name
207
X
20B
X
20F
X
20J
X
20N
X
20R
X
20d
X
APL5320-14QB
APL5320-18QB
APL5320-22QB
APL5320-26QB
APL5320-30QB
APL5320-34QB
APL5320-37QB
Marking
208
X
20C
X
20G
X
20K
X
20O
X
20S
X
206
X
Product Name
APL5320-15QB
APL5320-19QB
APL5320-23QB
APL5320-27QB
APL5320-31QB
APL5320-35QB
APL5320-475QB
Marking
209
X
20D
X
20H
X
20L
X
20P
X
20T
X
204
X
Note: X - Code.
SC-70-5
Product Name
Marking
Product Name
Marking
Product Name
Marking
Product Name
Marking
APL5320-12S5
205
AP5320-13S5
207
APL5320-14S5
208
APL5320-15S5
209
APL5320-16S5
20A
APL5320-17S5
20B
APL5320-18S5
20C
APL5320-19S5
20D
APL5320-20S5
20E
APL5320-21S5
20F
APL5320-22S5
20G
APL5320-23S5
20H
APL5320-24S5
20I
APL5320-25S5
20J
APL5320-26S5
20K
APL5320-27S5
20L
APL5320-28S5
20M
APL5320-29S5
20N
APL5320-30S5
20O
APL5320-31S5
20P
APL5320-32S5
20Q
APL5320-33S5
20R
APL5320-34S5
20S
APL5320-35S5
20T
APL5320-36S5
20g
APL5320-285S5
20d
APL5320-37S5
206
APL5320-475S5
204
Marking
Product Name
Marking
Product Name
Marking
Product Name
Marking
VTDFN1.2x1.6-4
Product Name
APL5320-12QF
APL5320-16QF
APL5320-20QF
APL5320-24QF
APL5320-28QF
APL5320-32QF
APL5320-36QF
05
X
0A
X
0E
X
0I
X
0M
X
0Q
X
0g
X
APL5320-13QF
APL5320-17QF
APL5320-21QF
APL5320-25QF
APL5320-29QF
APL5320-33QF
APL5320-285QF
07
X
0B
X
0F
X
0J
X
0N
X
0R
X
0d
X
APL5320-14QF
APL5320-18QF
APL5320-22QF
APL5320-26QF
APL5320-30QF
APL5320-34QF
APL5320-37QF
08
X
0C
X
0G
X
0K
X
0O
X
0S
X
06
X
APL5320-15QF
APL5320-19QF
APL5320-23QF
APL5320-27QF
APL5320-31QF
APL5320-35QF
APL5320-475QF
09
X
0D
X
0H
X
0L
X
0P
X
0T
X
04
X
Note : X - Code.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
3
www.anpec.com.tw
APL5320
Absolute Maximum Ratings
Rating
Unit
VIN to GND Voltage
Parameter
-0.3 ~ 6.5
V
VOUT to GND Voltage
-0.3 ~ 6.5
V
SHDN to GND Voltage
-0.3 ~ 6.5
Maximum Junction Temperature
-40 ~ 150
o
-65 ~ 150
o
260
o
Symbol
VIN
VOUT
VSHDN
TJ
TSTG
TSDR
(Note 1)
Storage Temperature
Maximum Lead Soldering Temperature, 10 Seconds
V
C
C
C
Note 1 : Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Thermal Characteristics
Symbol
Parameter
Junction-to-Ambient Resistance in Free Air
Typical Value
Unit
(Note 2)
SOT-23-5
240
TSOT-23-5
250
SOT-23-3
240
SC-70-5
325
TDFN1.6x1.6-6
165
VTDFN1.2x1.6-4
100
θJA
o
C/W
Note 2 : θJA is measured with the component mounted on a high effective thermal conductivity test board in free air.
Recommended Operating Conditions (Note 3)
Symbol
VIN
VSHDN
IOUT
Parameter
Range
Unit
VIN Input Voltage
2.5 ~ 6
V
SHDN Input Voltage
2.5 ~ 6
V
VOUT Output Current
0 ~300
mA
VOUT
Output Voltage
COUT
Output Capacitor
TA
TJ
Fixed Voltage
µF
1~22
Ambient Temperature
Junction Temperature
-40 ~ 85
o
C
-40 ~ 125
o
C
Note 3 : Refer to the typical application circuit.
Electrical Characteristics
Unless otherwise specified, these specifications apply over VIN=VOUT+1V, CIN=COUT=1µF and TA=-40~85 oC. Typical
values are at TA=25oC.
Symbol
Parameter
APL5320
Test Conditions
Unit
Min.
Typ.
Max.
1.9
2.2
2.4
V
UNDER-VOLTAGE LOCKAGE (UVLO) AND SUPPLY CURRENT
VIN UVLO Threshold Voltage
VIN rising, TA=-40~85oC
VIN UVLO Hysteresis
IQ
IQSHDN
Quiescent Current
Shut Down Supply Current
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
-
0.1
-
V
IOUT=0mA, VSHDN=5V
-
40
60
µA
IOUT=300mA VSHDN=5V
-
40
60
µA
VSHDN=0V, VIN= VOUT+1V
-
-
1
µA
4
www.anpec.com.tw
APL5320
Electrical Characteristics (Cont.)
Unless otherwise specified, these specifications apply over VIN=VOUT+1V, CIN=COUT=1µF and TA=-40~85 oC. Typical
values are at TA=25oC.
Symbol
Parameter
APL5320
Test Conditions
Unit
Min.
Typ.
Max.
IOUT=1mA, TA=25 oC
-2
-
2
%
IOUT=1mA to 300mA, TA=-40~85oC
-3
-
3
%
REGLINE Line Regulation
ΔVOUT%/ΔVIN, VOUT+0.3V<VIN<6V,
IOUT=1mA
-
-
0.2
%/V
REGLOAD Load Regulation
ΔVOUT%, VIN= VOUT+1V,
0mA<IOUT<300mA
-
-
0.6
%
VOUT=1.5V, IOUT=300mA
-
0.52
0.68
V
VOUT=2V, IOUT=300mA
-
0.43
0.56
V
VOUT=3V, IOUT=300mA
-
0.29
0.38
V
f=1kHz
-
70
-
dB
f=10kHz
-
63
-
dB
f=100kHz
OUTPUT VOLTAGE
Output Voltage Accuracy
VDROP
Dropout Voltage
OUTPUT VOLTAGE
PSRR
Ripple Rejection
COUT=1µF,
IOUT=50mA
-
35
-
dB
Output Noise
f=10Hz to 100kHz, COUT=10µF, IOUT = 1mA
-
100
-
µVRMS
VOUT Discharge Resistance
VSHDN=0V
-
0.7
-
kΩ
SHUT DOWN
VSHDN
ISHDN
High Threshold Voltage
VIN=2.5 to 6V
1.5
-
-
V
Low Threshold Voltage
VIN=2.5 to 6V
-
-
0.4
V
SHDN Input Current
VSHDN=5V
-
0.2
-
µA
330
450
750
mA
PROTECTIONS
ILIMIT
ISHORT
tSS
TOTP
Current-Limit Threshold
Short-Circuit Current
VOUT =0V
-
50
-
mA
Soft-Start
VOUT rising from 0 to 90%, RLOAD=50Ω
-
60
-
µs
Over-Temperature Threshold
TJ rising
-
160
-
o
-
o
Over-Temperature Hysteresis
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
-
5
40
C
C
www.anpec.com.tw
APL5320
Typical Operating Characteristics
Quiescent Current vs. Temperature
350
42
300
41
Quiescent Current (µA)
Quiescent Current (µA)
Quiescent Current vs. Supply Voltage
250
200
150
100
50
0
APL5320-12,
VIN=VEN=4.2V
40
39
38
37
36
35
0
1
2
3
4
Supply Voltage (V)
5
34
-40 -25
6
PSRR vs. Frequency
0
25
50
75
Temperature (oC)
100
125
Dropout Voltage vs. Output Current
0
400
APL5320-12, VIN=4V,
COUT=1µF, IOUT=50mA
APL5320-30,
COUT=1µF
350
Dropout Voltage (mV)
PSRR (dB)
-20
-40
-60
-80
300
TJ=125oC
250
TJ=25oC
200
150
TJ=-40oC
100
50
-100
100
1k
10k
100k
Frequency (Hz)
0
1M
100
300
200
Output Current (mA)
Output Noise
Current-Limit Threshold vs. Input Voltage
700
200
APL5320-12, IOUT=50mA,
VIN=VEN=4.2V(Battery)
650
100
Current-Limit (mA)
Output Noise (µV)
0
0
-100
600
550
500
450
-200
0
20
40
60
80
400
2.5
100
Time (ms)
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
6
3
3.5
4
4.5
5
Input Voltage (V)
5.5
6
www.anpec.com.tw
APL5320
Typical Operating Characteristics (Cont.)
Current-Limit Threshold vs. Temperature
Quiescent Current vs. Output Current
700
45
Quiescent Current (µA)
Current-Limit (mA)
650
600
550
500
450
400
APL5320-12, COUT=1µF,
VIN=VEN=4.2V
44.5
44
43.5
43
42.5
350
300
-40 -25
0
25
50
75
Temperature (oC)
100
42
125
0
50
100
150
200
250
300
Output Current (mA)
SHDN Pin Threshold Voltage vs.
Supply Voltage
1.5
1.4
SHDN Rising Threshold
EN Pin Threshold (V)
1.3
1.2
1.1
1.0
0.9
SHDN Falling Threshold
0.8
0.7
0.6
0.5
0.4
2.5
3
3.5
4
4.5
5
Supply Voltage (V)
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
5.5
6
7
www.anpec.com.tw
APL5320
Operating Waveforms
The test condition is VIN=4.2V, TA= 25oC unless otherwise specified.
Load Transient Response
Load Transient Response
VOUT
VOUT
1
1
I OUT
IOUT
2
2
VIN =4.2V, VOUT=1.2V, CIN =COUT =1µF,
IOUT =10mA to 300mA to 10mA (Rise/Fall time=1µs)
VIN =4.2V, VOUT=1.2V, CIN =COUT =1µF,
IOUT =10mA to 150mA to 10mA (Rise/Fall time=1µs)
CH1: VOUT, 50mV/Div, DC, Offset=1.2V
CH2: IOUT, 200mA/Div, DC
CH1: VOUT, 50mV/Div, DC, Offset=1.2V
CH2: IOUT, 100mA/Div, DC
TIME: 20µs/Div
TIME: 20µs/Div
Line Transient Response
Load Transient Response
1
VIN
VOUT
1
V OUT
2
IOUT
2
VIN =4.2V, VOUT=1.2V, CIN =COUT =1µF,
IOUT =10mA to 50mA to 10mA (Rise/Fall time=1µs)
VIN =3.8V to 4.8V to 3.8V (Rise/Fall time=4µs),
VOUT=1.2V, CIN =COUT =1µF, IOUT =100mA
CH1: VOUT, 20mV/Div, DC, Offset=1.2V
CH2: IOUT, 50mA/Div, DC
CH1: VIN, 500mV/Div, DC, Offset=3.8V
CH2: VOUT, 20mV/Div, DC, Offset=1.2V
TIME: 20µs/Div
TIME: 20µs/Div
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
8
www.anpec.com.tw
APL5320
Operating Waveforms (Cont.)
The test condition is VIN=4.2V, TA= 25oC unless otherwise specified.
Line Transient Response
Line Transient Response
VIN
VIN
1
1
VOUT
VOUT
2
2
VIN =3.8V to 4.8V to 3.8V (Rise/Fall time=4µs),
VOUT=1.2V, CIN =COUT =1µF, IOUT =50mA
VIN =3.8V to 4.8V to 3.8V (Rise/Fall time=4µs),
VOUT=1.2V, CIN =COUT =1µF, IOUT =10mA
CH1: VIN, 500mV/Div, DC, Offset=3.8V
CH2: VOUT, 20mV/Div, DC, Offset=1.2V
CH1: VIN, 500mV/Div, DC, Offset=3.8V
CH2: VOUT, 20mV/Div, DC, Offset=1.2V
TIME: 20µs/Div
TIME: 20µs/Div
Exiting Shutdown
Entering Shutdown
VSHDN
VSHDN
1
1
V OUT
VOUT
2
2
VIN =4.2V, VOUT=1.2V, CIN =COUT =1µF,
IOUT =10mA
VIN =4.2V, VOUT=1.2V, CIN =COUT =1µF,
IOUT =10mA
CH1: VSHDN, 2V/Div, DC
CH2: VOUT, 500mV/Div, DC
CH1: VSHDN, 2V/Div, DC
CH2: VOUT, 500mV/Div, DC
TIME: 20µs/Div
TIME: 10µs/Div
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
9
www.anpec.com.tw
APL5320
Pin Description
PIN
NO.
SOT-23-5/
TSOT-23-5/ SOT-23-3
SC-70-5
TDFN
1.6x1.6-6
VTDFN
1.2x1.6-4
FUNCTION
NAME
1
3
3
4
VIN
Voltage Supply Input Pin.
2
1
6
2
GND
Ground.
3
-
1
3
SHDN
4
-
2, 5
-
NC
5
2
4
1
VOUT
Shut Down Control Pin. Logic high: enable; logic low: shutdown.
This pin can not be left floating.
NC Pin.
Regulator Output Pin.
Block Diagram
UVLO &
Shutdown
Logic
SHDN
VIN
+
CurrentLimit
Thermal
Shutdown
Foldback
Current-Limit
VOUT
VREF
GND
Typical Application Circuit
APL5320
VIN
VIN
CIN
1µF
VOUT
VOUT
SHDN
GND
COUT
1µF
Enable
Shutdown
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
10
www.anpec.com.tw
APL5320
Function Description
Internal Soft-Start
An internal soft-start function controls rising rate of the
output voltage to limit the surge current at start-up. The
typical soft-start interval is about 60µs.
Thermal Shutdown
A thermal shutdown circuit limits the junction temperature of APL5320. When the junction temperature exceeds
+160oC, a thermal sensor turns off the output PMOS, allowing the device to cool down. The regulator regulates
the output again through initiation of a new soft-start cycle
after the junction temperature cools by 40oC.The thermal
shutdown is designed with a 40oC hysteresis to lower
the average junction temperature during continuous thermal overload conditions, extending lifetime of the device.
For normal operation, device power dissipation should
be externally limited so that junction temperature will not
exceed 125oC.
Current-Limit with Current Foldback
The APL5320 monitors the current via the output PMOS
and limits the maximum current. When the output current
reaches the current-limit threshold, current-limit with current foldback circuit starts to work to prevent load and
APL5320 from damages during overload or short-circuit
conditions. Typical foldback current is about 50mA.
Shutdown Control
The APL5320 has an active-low shutdown function. Forcing SHDN high (>1.5V) enables the VOUT; forcing SHDN
low (<0.4V) disables the VOUT. The SHDN can not be left
floating. If it is not used, connect it to VIN for normal
operation.
Under-Voltage Lock Out (UVLO)
The APL5320 monitors the input voltage to prevent wrong
logic control. The UVLO function initiates a soft-start process after input voltage exceeds its rising UVLO threshold during power on. The UVLO function also shuts off
the output when the input voltage falls below it’s falling
threshold.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
11
www.anpec.com.tw
APL5320
Application Information
Input capacitor
Operation Region and Power Dissipation
The APL5320 requires proper input capacitors to supply
surge current during stepping load transients to prevent
The APL5320 maximum power dissipation depends on
the thermal resistance and temperature difference be-
the input rail from dropping. Because the parasitic inductor from the voltage sources or other bulk capacitors to
tween the die junction and ambient air. The TDFN1.6x1.6-6
package power dissipation PD across the device is:
the VIN limit the slew rate of the surge current, place the
Input capacitors near VIN as close as possible. Input
PD = (TJ - TA) / θJA
where (TJ - TA) is the temperature difference between the
capacitors should be larger than 1µF and a minimum
ceramic capacitor of 1µF is necessary.
junction and ambient air. θJA is the thermal resistance
between Junction and ambient air. Assuming the TA=25oC
Output Capacitor
and maximum TJ=160oC (typical thermal limit threshold),
the maximum power dissipation is calculated as:
The APL5320 needs a proper output capacitor to maintain circuit stability and improve transient response over-
PD(max)=(160-25)/165=0.81(W)
For normal operation, do not exceed the maximum junc-
temperature and current. In order to insure the circuit
stability, the proper output capacitor value should be larger
tion temperature rating of TJ=125oC. The calculated power
dissipation should be less than:
than 1µF. With X5R and X7R dielectrics, 1µF is sufficient
at all operating temperatures. Large output capacitor
PD=(125-25)/165=0.6(W)
The GND provides an electrical connection to the ground
value can reduce noise and improve load-transient response and PSRR, Figure 1 shows the curves of allow-
and channels heat away. Connect the GND to the ground
by using a large pad or a ground plane.
able ESR range as the function of load current for various
output capacitor values.
Layout Consideration
Figure 2 illustrates the layout. Below is a checklist for
Region of Stable COUT ESR vs. Output Current
your layout:
1. Please place the input capacitors close to the VIN.
Region of Stable COUT ESR (Ω)
10
APL5320-12
VIN=VEN=4.2V
CIN=COUT=1µF/X7R
2. Ceramic capacitors for load must be placed near the
load as close as possible.
1
3. To place APL5320 and output capacitors near the load
is good for performance.
Unstable Range
0.1
4. Large current paths, the bold lines in figure 2, must
have wide tracks.
Stable Range
VIN
VIN
ON
SHDN VOUT
GND
0.01
Simulation Verify
0.001
0
50
100
150
200
250
VOUT
OFF
300
Output Current (mA)
Figure2. Large Current Paths Shown as Bold Lines
Figure1. Stable COUT ESR Range
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
12
www.anpec.com.tw
APL5320
Application Information(Cont.)
Recommended Minimum Footprint
1.30
0.95
1.17
1.27
2.54
2.06
1.90
0.65
0.5
0.3
Unit: mm
Unit: mm
SOT-23-5/TSOT-23-5
SC-70-5
Thermal Via
Φ0.30mm
Thermal Via
Φ0.30mm
0.6
2.0
0.45
1.0
0.5
0.8
0.45
1.6
0.7
2.1
0.25
0.35
0.6
Unit: mm
Unit:mm
VTDFN1.2x1.6-4
TDFN1.6x1.6-6
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
13
www.anpec.com.tw
APL5320
Package Information
SOT-23-5
D
e
E
E1
SEE
VIEW A
b
c
0.25
A
L
0
GAUGE PLANE
SEATING PLANE
A1
A2
e1
VIEW A
S
Y
M
B
O
L
SOT-23-5
INCHES
MILLIMETERS
MIN.
MIN.
MAX.
A
MAX.
1.45
0.057
A1
0.00
0.15
0.000
A2
0.90
1.30
0.035
0.051
b
0.30
0.50
0.012
0.020
c
0.08
0.22
0.003
0.009
D
2.70
3.10
0.106
0.122
0.118
0.071
E
2.60
3.00
0.102
E1
1.40
1.80
0.055
e
0.95 BSC
0.037 BSC
e1
1.90 BSC
0.075 BSC
L
0.30
0.60
0
0°
8°
0.012
0°
0.006
0.024
8°
Note : 1. Follow JEDEC TO-178 AA.
2. Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
14
www.anpec.com.tw
APL5320
Package Information
TSOT-23-5
D
e
E
E1
SEE VIEW A
c
b
0.25
A
GAUGE PLANE
SEATING PLANE
A1
A2
e1
L
VIEW A
S
Y
M
B
O
L
TSOT-23-5
MILLIMETERS
INCHES
MIN.
MAX.
MIN.
MAX.
A
0.70
1.00
0.028
0.039
A1
0.01
0.10
0.000
0.004
A2
0.70
0.90
0.028
0.035
b
0.30
0.50
0.012
0.020
c
0.08
0.22
0.003
0.009
D
2.70
3.10
0.106
0.122
E
2.60
3.00
0.102
0.118
E1
1.40
1.80
0.055
e
0.95 BSC
e1
0.071
0.037 BSC
1.90BSC
0.075 BSC
L
0.30
0.60
0
0°
8°
0.012
0°
0.024
8°
Note : 1. Followed from JEDEC TO-178 AA.
2. Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per
side.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
15
www.anpec.com.tw
APL5320
Package Information
SC-70-5
D
e
E
E1
SEE VIEW A
c
b
0.15
A
GAUGE PLANE
SEATING PLANE
A1
A2
e1
L
VIEW A
S
Y
M
B
O
L
SC-70-5
INCHES
MILLIMETERS
MIN.
MAX.
MIN.
MAX.
A
0.80
1.10
0.031
0.043
A1
0.00
0.10
0.000
0.004
A2
0.80
1.00
0.031
0.040
b
0.15
0.30
0.006
0.012
c
0.08
0.25
0.003
0.010
D
1.90
2.20
0.075
0.087
E
2.00
2.40
0.079
0.095
E1
1.15
1.35
0.045
0.053
e
e1
L
0
0.026 BSC
0.65 BSC
1.30 BSC
0.15
0o
0.051 BSC
0.006
0.45
8o
0o
0.018
8o
Note : 1. Followed from JEDEC MO-223 AB.
2. Dimension D and E1 do not include mold flash, protrusions or gate burrs.
Mold flash, protrusion or gate burrs shall not exceed 6 mil per side.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
16
www.anpec.com.tw
APL5320
Package Information
SOT-23-3
D
e
E
E1
SEE
VIEW A
c
b
0.25
A
L
GAUGE PLANE
SEATING PLANE
0
A1
A2
e1
VIEW A
S
Y
M
B
O
L
SOT-23-3
INCHES
MILLIMETERS
MIN.
MIN.
MAX.
A
MAX.
1.45
0.057
A1
0.00
0.15
0.000
A2
0.90
1.30
0.035
0.051
b
0.30
0.50
0.012
0.020
c
0.08
0.22
0.003
0.009
D
2.70
3.10
0.106
0.122
E
2.60
3.00
0.102
0.118
E1
1.40
1.80
0.055
0.071
e
0.95 BSC
e1
1.90 BSC
0.006
0.037 BSC
0.075 BSC
L
0.30
0.60
0
0°
8°
0.012
0°
0.024
8°
Note : Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
17
www.anpec.com.tw
APL5320
Package Information
TDFN1.6x1.6-6
D
E
A
b
Pin 1
A1
D2
E2
A3
L
K
Pin 1 Corner
e
S
Y
M
B
O
L
MIN.
MAX.
MIN.
MAX.
A
0.70
0.80
0.028
0.031
A1
0.00
0.05
0.000
0.002
0.20
0.30
0.008
0.012
D
1.55
1.65
0.061
0.065
D2
0.95
1.05
0.037
0.041
TDFN1.6x1.6-6
MILLIMETERS
A3
b
INCHES
0.20 REF
0.008 REF
E
1.55
1.65
0.061
0.065
E2
0.55
0.65
0.022
0.026
e
0.50 BSC
0.020 BSC
K
0.20
-
0.008
-
L
0.19
0.29
0.007
0.011
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
18
www.anpec.com.tw
APL5320
Package Information
VTDFN1.2x1.6-4
A
E2
e
b
E
D
Pin 1 Cirner
D2
S
Y
M
B
O
L
K
L
VTDFN1.2x1.6-4
MILLIMETERS
INCHES
MIN.
MAX.
MIN.
MAX.
A
0.50
0.60
0.020
0.024
b
0.25
0.35
0.010
0.014
D
1.55
1.65
0.061
0.065
D2
0.65
0.75
0.026
0.030
E
1.15
1.25
0.045
0.049
E2
0.95
1.05
0.037
0.041
0.30
0.004
e
0.60 BSC
L
0.10
K
0.20
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
0.024 BSC
0.012
0.008
19
www.anpec.com.tw
APL5320
Carrier Tape & Reel Dimensions
P0
P2
P1
A
B0
W
F
E1
OD0
K0
A0
A
OD1 B
B
T
SECTION A-A
SECTION B-B
H
A
d
T1
Application
SOT-23-5
Application
TSOT-23-5
Application
SOT-23-3
A
H
T1
C
d
D
W
E1
F
178.0±2.00
50 MIN.
8.4+2.00
-0.00
13.0+0.50
-0.20
1.5 MIN.
20.2 MIN.
8.0±0.30
1.75±0.10
3.5±0.05
P0
P1
P2
D0
D1
T
A0
B0
K0
2.0±0.05
1.5+0.10
-0.00
1.0 MIN.
0.6+0.00
-0.40
3.20±0.20
3.10±0.20
1.50±0.20
4.0±0.10
4.0±0.10
A
H
T1
C
d
D
W
E1
F
178.0±2.00
50 MIN.
8.4+2.00
-0.00
13.0+0.50
-0.20
1.5 MIN.
20.2 MIN.
8.0±0.30
1.75±0.10
3.5±0.05
P0
P1
P2
D0
D1
T
A0
B0
K0
2.0±0.05
1.5+0.10
-0.00
1.0 MIN.
0.6+0.00
-0.40
3.20±0.20
3.10±0.20
1.50±0.20
4.0±0.10
4.0±0.10
A
H
T1
C
d
D
W
E1
F
178.0±2.00
50 MIN.
8.4+2.00
-0.00
13.0+0.50
-0.20
1.5 MIN.
20.2 MIN.
8.0±0.30
1.75±0.10
3.5±0.05
P0
P1
P2
D0
D1
T
A0
B0
K0
2.0±0.05
1.5+0.10
-0.00
1.0 MIN.
0.6+0.00
-0.40
3.20±0.20
3.10±0.20
1.50±0.20
4.0±0.10
4.0±0.10
(mm)
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
20
www.anpec.com.tw
APL5320
Carrier Tape & Reel Dimensions (Cont.)
Application
A
H
178.0±
2.00
50 MIN.
P0
P1
SC-70-5
T1
C
8.4+2.00 13.0+0.50
-0.00
-0.20
d
D
W
E1
F
1.5 MIN.
20.2 MIN.
8.0±0.30
1.75±0.10
3.50±0.05
P2
D0
D1
T
A0
B0
K0
2.0±0.05
1.5+0.10
-0.00
1.00 MIN.
0.6+0.00
-0.40
2.40±0.20
2.40±0.20
1.20±0.20
4.0±0.10
4.0±0.10
A
H
T1
C
d
D
W
E1
F
178.0±
2.00
50 MIN.
8.4+2.00
-0.00
13.0+0.50
-0.20
1.5 MIN.
20.2 MIN.
8.0±0.30
1.75±0.10
3.5±0.05
P0
P1
P2
D0
D1
T
A0
B0
K0
2.0±0.05
1.5+0.10
-0.00
1.5 MIN.
0.6+0.00
-0.40
1.70±0.20
1.70±0.20
0.90±0.20
Application
TDFN1.6x1.6-6
4.0±0.10
4.0±0.10
A
H
T1
C
d
D
W
E1
F
178.0±
2.00
50 MIN.
8.4+2.00
-0.00
13.0+0.50
-0.20
1.5 MIN.
20.2 MIN.
8.0±0.20
1.75±0.10
3.50±0.05
P0
P1
P2
D0
D1
T
A0
B0
K0
4.0±0.10
4.0±0.10
2.0±0.05
1.5+0.10
-0.00
1.5 MIN.
0.6+0.00
-0.4
1.4 MIN
1.8 MIN
0.75±0.20
Application
VTDFN1.2x1.6-4
(mm)
Devices Per Unit
Package Type
Unit
Quantity
SOT-23-5
Tape & Reel
3000
TSOT-23-5
Tape & Reel
3000
SOT-23-3
Tape & Reel
3000
SC-70-5
Tape & Reel
3000
TDFN1.6x1.6-6
Tape & Reel
3000
VTDFN1.2x1.6-4
Tape & Reel
3000
Taping Direction Information
(T)SOT-23-5
USER DIRECTION OF FEED
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
21
www.anpec.com.tw
APL5320
Taping Direction Information (Cont.)
SOT-23-3
USER DIRECTION OF FEED
SC-70-5
USER DIRECTION OF FEED
TDFN1.6x1.6-6
USER DIRECTION OF FEED
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
22
www.anpec.com.tw
APL5320
Taping Direction Information (Cont.)
VTDFN1.2x1.6-4
USER DIRECTION OF FEED
Classification Profile
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
23
www.anpec.com.tw
APL5320
Classification Reflow Profiles
Profile Feature
Sn-Pb Eutectic Assembly
Pb-Free Assembly
100 °C
150 °C
60-120 seconds
150 °C
200 °C
60-120 seconds
3 °C/second max.
3 °C/second max.
183 °C
60-150 seconds
217 °C
60-150 seconds
See Classification Temp in table 1
See Classification Temp in table 2
Time (tP)** within 5°C of the specified
classification temperature (Tc)
20** seconds
30** seconds
Average ramp-down rate (Tp to Tsmax)
6 °C/second max.
6 °C/second max.
6 minutes max.
8 minutes max.
Preheat & Soak
Temperature min (Tsmin)
Temperature max (Tsmax)
Time (Tsmin to Tsmax) (ts)
Average ramp-up rate
(Tsmax to TP)
Liquidous temperature (TL)
Time at liquidous (tL)
Peak package body Temperature
(Tp)*
Time 25°C to peak temperature
* Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum.
** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum.
Table 1. SnPb Eutectic Process – Classification Temperatures (Tc)
Package
Thickness
<2.5 mm
≥2.5 mm
Volume mm
<350
235 °C
220 °C
3
Volume mm
≥350
220 °C
220 °C
3
Table 2. Pb-free Process – Classification Temperatures (Tc)
Package
Thickness
<1.6 mm
1.6 mm – 2.5 mm
≥2.5 mm
Volume mm
<350
260 °C
260 °C
250 °C
3
Volume mm
350-2000
260 °C
250 °C
245 °C
3
Volume mm
>2000
260 °C
245 °C
245 °C
3
Reliability Test Program
Test item
SOLDERABILITY
HOLT
PCT
TCT
HBM
MM
Latch-Up
Method
JESD-22, B102
JESD-22, A108
JESD-22, A102
JESD-22, A104
MIL-STD-883-3015.7
JESD-22, A115
JESD 78
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
24
Description
5 Sec, 245°C
1000 Hrs, Bias @ Tj=125°C
168 Hrs, 100%RH, 2atm, 121°C
500 Cycles, -65°C~150°C
VHBM≧2KV
VMM≧200V
10ms, 1tr≧100mA
www.anpec.com.tw
APL5320
Customer Service
Anpec Electronics Corp.
Head Office :
No.6, Dusing 1st Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,
Sindian City, Taipei County 23146, Taiwan
Tel : 886-2-2910-3838
Fax : 886-2-2917-3838
Copyright  ANPEC Electronics Corp.
Rev. A.9 - Mar., 2012
25
www.anpec.com.tw
Similar pages