Elpida EDE5116AHBG-4A-E 512m bits ddr2 sdram Datasheet

PRELIMINARY DATA SHEET
512M bits DDR2 SDRAM
EDE5108AHBG (64M words × 8 bits)
EDE5116AHBG (32M words × 16 bits)
Features
• Density: 512M bits
• Organization
 16M words × 8 bits × 4 banks (EDE5108AHBG)
 8M words × 16 bits × 4 banks (EDE5116AHBG)
• Package
 60-ball FBGA (EDE5108AHBG)
 84-ball FBGA (EDE5116AHBG)
 Lead-free (RoHS compliant)
• Power supply: VDD, VDDQ = 1.8V ± 0.1V
• Data rate: 800Mbps/667Mbps/533Mbps/400Mbps
(max.)
• 1KB page size (EDE5108AHBG)
 Row address: A0 to A13
 Column address: A0 to A9
• 2KB page size (EDE5116AHBG)
 Row address: A0 to A12
 Column address: A0 to A9
• Four internal banks for concurrent operation
• Interface: SSTL_18
• Burst lengths (BL): 4, 8
• Burst type (BT):
 Sequential (4, 8)
 Interleave (4, 8)
• /CAS Latency (CL): 3, 4, 5, 6
• Precharge: auto precharge option for each burst
access
• Driver strength: normal/weak
• Refresh: auto-refresh, self-refresh
• Double-data-rate architecture; two data transfers per
clock cycle
• The high-speed data transfer is realized by the 4 bits
prefetch pipelined architecture
• Bi-directional differential data strobe (DQS and /DQS)
is transmitted/received with data for capturing data at
the receiver
• DQS is edge-aligned with data for READs; centeraligned with data for WRITEs
• Differential clock inputs (CK and /CK)
• DLL aligns DQ and DQS transitions with CK
transitions
• Commands entered on each positive CK edge; data
and data mask referenced to both edges of DQS
• Data mask (DM) for write data
• Posted /CAS by programmable additive latency for
better command and data bus efficiency
• Off-Chip-Driver Impedance Adjustment and On-DieTermination for better signal quality
• Programmable RDQS, /RDQS output for making × 8
organization compatible to × 4 organization
• /DQS, (/RDQS) can be disabled for single-ended
Data Strobe operation
L
EO
Specifications
t
uc
 Average refresh period
7.8µs at 0°C ≤ TC ≤ +85°C
3.9µs at +85°C < TC ≤ +95°C
• Operating case temperature range
 TC = 0°C to +95°C
od
Pr
• Refresh cycles: 8192 cycles/64ms
Document No. E0933E30 (Ver. 3.0)
Date Published September 2006 (K) Japan
Printed in Japan
URL: http://www.elpida.com
This product became EOL in June, 2010.
Elpida Memory, Inc. 2006
EDE5108AHBG, EDE5116AHBG
Ordering Information
Mask
version
Part number
EDE5108AHBG-8E-E
EDE5108AHBG-8G-E
EDE5108AHBG-6E-E
EDE5108AHBG-5C-E
EDE5108AHBG-4A-E
EDE5116AHBG-8E-E
EDE5116AHBG-8G-E
EDE5116AHBG-6E-E
EDE5116AHBG-5C-E
EDE5116AHBG-4A-E
Organization
(words × bits)
64M × 8
H
Internal
Banks
Speed bin
(CL-tRCD-tRP)
Package
DDR2-800 (5-5-5)
DDR2-800 (6-6-6)
DDR2-667 (5-5-5)
DDR2-533 (4-4-4)
DDR2-400 (3-3-3)
DDR2-800 (5-5-5)
DDR2-800 (6-6-6)
DDR2-667 (5-5-5)
DDR2-533 (4-4-4)
DDR2-400 (3-3-3)
4
32M × 16
60-ball FBGA
84-ball FBGA
EO
Part Number
E D E 51 08 A H BG - 8E - E
Elpida Memory
Type
D: Monolithic Device
L
Product Family
E: DDR2
Environment code
E: Lead Free
(RoHS compliant)
Speed
8E: DDR2-800 (5-5-5)
8G: DDR2-800 (6-6-6)
6E: DDR2-667 (5-5-5)
5C: DDR2-533 (4-4-4)
4A: DDR2-400 (3-3-3)
Density / Bank
51: 512Mb /4-bank
Power Supply, Interface
A: 1.8V, SSTL_18
Package
BG: FBGA
Die Rev.
t
uc
od
Pr
Organization
08: x8
16: x16
Preliminary Data Sheet E0933E30 (Ver. 3.0)
2
EDE5108AHBG, EDE5116AHBG
Pin Configurations
/xxx indicates active low signal.
60-ball FBGA
(×8 organization)
1
2
3
84-ball FBGA
(×16 organization)
7
8
9
A
VDD NU/ /RDQS VSS
1
2
3
VDD
NC
VSS
VSSQ /UDQS VDDQ
DQ14 VSSQ UDM
UDQS VSSQ DQ15
VDDQ
VDDQ
7
8
9
A
VSSQ /DQS VDDQ
B
B
DQ6
VSSQ DM/RDQS
DQS
VSSQ
DQ7
C
C
VDDQ
DQ1 VDDQ
VDDQ
DQ0
VDDQ
D
D
DQ4
VSSQ
DQ3
EO
DQ2
VSSQ
DQ5
VSSDL
CK
VDD
E
VDDL VREF
VSS
BA0
/WE
/RAS
/CK
ODT
BA1
/CAS
/CS
VSS
A3
A1
A2
A0
VDD
A5
A6
A12
VDD
NC
VSS
VSSQ /LDQS VDDQ
DQ6
VSSQ
LDM
LDQS VSSQ
VDDQ
VDD
A9
A11
NC
NC
A8
DQ7
DQ1 VDDQ
VDDQ
DQ0
VDDQ
DQ4
VSSQ
DQ3
DQ2
VSSQ
DQ5
VDDL VREF
VSS
VSSDL
CK
VDD
CKE
/WE
/RAS
/CK
ODT
BA0
BA1
/CAS
/CS
A10
A1
A2
A0
A3
A5
A6
A4
A7
A9
A11
A8
A12
NC
NC
NC
J
A4
L
A7
L
DQ10 VSSQ DQ13
H
J
K
DQ12 VSSQ DQ11
G
H
A10
VDDQ
F
G
NC
DQ8
E
F
CKE
DQ9 VDDQ
K
VSS
L
A13
NC
M
(Top view)
VDD
N
Pr
VSS
P
VSS
R
VDD
Function
A0 to A13
Address inputs
BA0, BA1
Bank select
DQ0 to DQ15
Data input/output
DQS, /DQS
UDQS, /UDQS
LDQS, /LDQS
Differential data strobe
Pin name
Function
ODT
ODT control
VDD
Supply voltage for internal circuit
VSS
Ground for internal circuit
VDDQ
Supply voltage for DQ circuit
od
Pin name
(Top view)
Differential data strobe for read
/CS
Chip select
VSSQ
/RAS, /CAS, /WE
Command input
VDDL
CKE
Clock enable
VSSDL
CK, /CK
Differential clock input
NC*
1
DM
UDM, LDM
Write data mask
NU*
2
VREF
Ground for DQ circuit
uc
RDQS, /RDQS
Input reference voltage
Supply voltage for DLL circuit
Ground for DLL circuit
No connection
Not usable
t
Notes: 1. Not internally connected with die.
2. Don’t use other than reserved functions.
Preliminary Data Sheet E0933E30 (Ver. 3.0)
3
EDE5108AHBG, EDE5116AHBG
CONTENTS
L
EO
Specifications.................................................................................................................................................1
Features.........................................................................................................................................................1
Ordering Information......................................................................................................................................2
Part Number ..................................................................................................................................................2
Pin Configurations .........................................................................................................................................3
Electrical Specifications.................................................................................................................................5
Block Diagram .............................................................................................................................................23
Pin Function.................................................................................................................................................24
Command Operation ...................................................................................................................................26
Simplified State Diagram .............................................................................................................................33
Operation of DDR2 SDRAM ........................................................................................................................34
Package Drawing ........................................................................................................................................71
Recommended Soldering Conditions..........................................................................................................73
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
4
EDE5108AHBG, EDE5116AHBG
Electrical Specifications
• All voltages are referenced to VSS (GND)
• Execute power-up and Initialization sequence before proper device operation is achieved.
Absolute Maximum Ratings
Symbol
Rating
Unit
Notes
Power supply voltage
VDD
−1.0 to +2.3
V
1
Power supply voltage for output
VDDQ
−0.5 to +2.3
V
1
Input voltage
VIN
−0.5 to +2.3
V
1
Output voltage
VOUT
−0.5 to +2.3
V
1
Storage temperature
Tstg
−55 to +100
°C
1, 2
Power dissipation
PD
1.0
W
1
Short circuit output current
IOUT
50
mA
1
EO
Parameter
Notes: 1. Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect reliability.
2. Storage temperature is the case surface temperature on the center/top side of the DRAM.
Caution
L
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Operating Temperature Condition
Operating case temperature
Pr
Parameter
Symbol
Rating
Unit
Notes
TC
0 to +95
°C
1, 2
t
uc
od
Notes: 1. Operating temperature is the case surface temperature on the center/top side of the DRAM.
2. Supporting 0°C to +85°C with full AC and DC specifications.
Supporting 0°C to +85°C and being able to extend to +95°C with doubling auto-refresh commands in
frequency to a 32ms period (tREFI = 3.9µs) and higher temperature Self-Refresh entry via A7 "1" on
EMRS (2).
Preliminary Data Sheet E0933E30 (Ver. 3.0)
5
EDE5108AHBG, EDE5116AHBG
Recommended DC Operating Conditions (SSTL_18)
Parameter
Symbol
min.
typ.
max.
Unit
Notes
Supply voltage
VDD
1.7
1.8
1.9
V
4
Supply voltage for output
VDDQ
1.7
1.8
1.9
V
4
Input reference voltage
VREF
0.49 × VDDQ
0.50 × VDDQ 0.51 × VDDQ
V
1, 2
Termination voltage
VTT
VREF − 0.04
VREF
VREF + 0.04
V
3
DC input logic high
VIH (DC)
VREF + 0.125

VDDQ + 0.3
V
DC input low
VIL (DC)
−0.3

VREF – 0.125
V
AC input logic high
-8E, -8G, -6E
VIH (AC)
VREF + 0.200


V
VIH (AC)
VREF + 0.250


V
VIL (AC)


VREF − 0.200
V
VIL (AC)


VREF − 0.250
V
-5C, -4A
EO
AC input low
-8E, -8G, -6E
-5C, -4A
L
Notes: 1. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically
the value of VREF is expected to be about 0.5 × VDDQ of the transmitting device and VREF are expected
to track variations in VDDQ.
2. Peak to peak AC noise on VREF may not exceed ±2% VREF (DC).
3. VTT of transmitting device must track VREF of receiving device.
4. VDDQ tracks with VDD, VDDL tracks with VDD. AC parameters are measured with VDD, VDDQ and
VDDL tied together.
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
6
EDE5108AHBG, EDE5116AHBG
DC Characteristics 1 (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
Parameter
Symbol
Operating current
(ACT-PRE)
Operating current
(ACT-READ-PRE)
Precharge quiet
standby current
×16
max.
max.
-8E, -8G
-6E
-5C
-4A
75
70
65
60
90
85
80
75
mA
IDD1
-8E, -8G
-6E
-5C
-4A
85
80
75
70
105
100
90
85
mA
IDD2P
-8E, -8G
-6E
-5C
-4A
10
10
10
8
10
10
10
8
IDD2Q
-8E, -8G
-6E
-5C
-4A
28
25
22
20
28
25
22
20
mA
L
Idle standby current
mA
-8E, -8G
-6E
-5C
-4A
35
30
25
20
35
30
25
20
mA
-8E, -8G
-6E
IDD3P-F
-5C
-4A
25
20
20
15
25
20
20
15
mA
-8E, -8G
-6E
IDD3P-S
-5C
-4A
15
15
13
13
15
15
13
13
mA
IDD2N
all banks idle; tCK = tCK (IDD); CKE is L;
Other control and address bus inputs are
STABLE;
Data bus inputs are FLOATING
all banks idle; tCK = tCK (IDD);
CKE is H, /CS is H;
Other control and address bus inputs are
STABLE;
Data bus inputs are FLOATING
all banks idle; tCK = tCK (IDD);
CKE is H, /CS is H;
Other control and address bus inputs are
SWITCHING;
Data bus inputs are SWITCHING
all banks open;
tCK = tCK (IDD);
CKE is L;
Other control and
address bus inputs
are STABLE;
Data bus inputs
are FLOATING
Fast PDN Exit
MRS(12) = 0
Slow PDN Exit
MRS(12) = 1
all banks open;
tCK = tCK (IDD), tRAS = tRAS max.(IDD),
tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Other control and address bus inputs are
SWITCHING;
Data bus inputs are SWITCHING
all banks open, continuous burst reads,
IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD),
tRAS = tRAS max.(IDD), tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data pattern is same as IDD4W
all banks open, continuous burst writes;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD),
tRAS = tRAS max.(IDD), tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
-8E, -8G
-6E
-5C
-4A
50
45
40
35
50
45
40
35
mA
Operating current
(Burst read
operating)
IDD4R
-8E, -8G
-6E
-5C
-4A
135
115
95
75
175
150
125
105
mA
IDD4W
-8E, -8G
-6E
-5C
-4A
140
120
100
80
195
170
130
110
mA
t
IDD3N
uc
Active standby
current
Operating current
(Burst write
operating)
Test condition
one bank; tCK = tCK (IDD), tRC = tRC (IDD),
tRAS = tRAS min.(IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
one bank; IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD), tRC = tRC (IDD),
tRAS = tRAS min.(IDD); tRCD = tRCD (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data pattern is same as IDD4W
od
Pr
Active power-down
standby current
Unit
IDD0
EO
Precharge powerdown standby
current
Grade
×8
Preliminary Data Sheet E0933E30 (Ver. 3.0)
7
EDE5108AHBG, EDE5116AHBG
Parameter
Symbol
Auto-refresh current IDD5
Self-refresh current
IDD7
×16
max.
max.
195
190
185
180
6
-8E, -8G
-6E
-5C
-4A
170
160
150
140
195
190
185
180
6
250
240
230
220
Unit
Test condition
mA
tCK = tCK (IDD);
Refresh command at every tRFC (IDD)
interval;
CKE is H, /CS is H between valid commands;
Other control and address bus inputs are
SWITCHING;
Data bus inputs are SWITCHING
mA
Self Refresh Mode;
CK and /CK at 0V; CKE ≤ 0.2V;
Other control and address bus inputs are
FLOATING;
Data bus inputs are FLOATING
mA
all bank interleaving reads, IOUT = 0mA;
BL = 4, CL = CL(IDD),
AL = tRCD (IDD) −1 × tCK (IDD);
tCK = tCK (IDD), tRC = tRC (IDD),
tRRD = tRRD(IDD), tRCD = 1 × tCK (IDD);
CKE is H, CS is H between valid commands;
Address bus inputs are STABLE during
DESELECTs; Data pattern is same as IDD4W
IDD specifications are tested after the device is properly initialized.
Input slew rate is specified by AC Input Test Condition.
IDD parameters are specified with ODT disabled.
Data bus consists of DQ, DM, DQS, /DQS, RDQS and /RDQS. IDD values must be met with all
combinations of EMRS bits 10 and 11.
5. Definitions for IDD
L is defined as VIN ≤ VIL (AC) (max.)
H is defined as VIN ≥ VIH (AC) (min.)
STABLE is defined as inputs stable at an H or L level
FLOATING is defined as inputs at VREF = VDDQ/2
SWITCHING is defined as:
inputs changing between H and L every other clock cycle (once per two clocks) for address and control
signals, and inputs changing between H and L every other data transfer (once per clock) for DQ signals
not including masks or strobes.
6. Refer to AC Timing for IDD Test Conditions.
L
Notes: 1.
2.
3.
4.
-8E, -8G
-6E
-5C
-4A
IDD6
EO
Operating current
(Bank interleaving)
Grade
×8
od
Pr
AC Timing for IDD Test Conditions
For purposes of IDD testing, the following parameters are to be utilized.
DDR2-800
Parameter
5-5-5
6-6-6
CL (IDD)
5
6
tRCD (IDD)
12.5
15
tRC (IDD)
57.5
60
DDR2-667
DDR2-533
DDR2-400
5-5-5
4-4-4
3-3-3
Unit
5
4
3
tCK
15
15
15
ns
60
60
55
ns
uc
DDR2-800
7.5
7.5
7.5
7.5
tRRD (IDD)-×16
10
10
10
10
tCK (IDD)
2.5
2.5
3
3.75
tRAS (min.)(IDD)
45
45
45
45
40
ns
tRAS (max.)(IDD)
70000
70000
70000
70000
70000
ns
tRP (IDD)
12.5
15
15
15
15
ns
tRFC (IDD)
105
105
105
105
Preliminary Data Sheet E0933E30 (Ver. 3.0)
8
7.5
ns
10
ns
5
ns
105
t
tRRD (IDD)-×8
ns
EDE5108AHBG, EDE5116AHBG
DC Characteristics 2 (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
Parameter
Symbol
Value
Input leakage current
ILI
2
µA
VDD ≥ VIN ≥ VSS
Output leakage current
ILO
5
µA
VDDQ ≥ VOUT ≥ VSS
VTT + 0.603
V
5
VTT − 0.603
V
5
Output timing measurement reference level VOTR
0.5 × VDDQ
V
1
Output minimum sink DC current
IOL
+13.4
mA
3, 4, 5
Output minimum source DC current
IOH
−13.4
mA
2, 4, 5
Minimum required output pull-up under AC
VOH
test load
Maximum required output pull-down under
VOL
AC test load
Notes
The VDDQ of the device under test is referenced.
VDDQ = 1.7V; VOUT = 1.42V.
VDDQ = 1.7V; VOUT = 0.28V.
The DC value of VREF applied to the receiving device is expected to be set to VTT.
After OCD calibration to 18Ω at TC = 25°C, VDD = VDDQ = 1.8V.
EO
Notes: 1.
2.
3.
4.
5.
Unit
DC Characteristics 3 (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
Symbol
min.
max.
Unit
Notes
AC differential input voltage
VID (AC)
0.5
VDDQ + 0.6
V
1, 2
AC differential cross point voltage
VIX (AC)
0.5 × VDDQ − 0.175
0.5 × VDDQ + 0.175
V
2
AC differential cross point voltage
VOX (AC)
0.5 × VDDQ − 0.125
0.5 × VDDQ + 0.125
V
3
L
Parameter
od
Pr
Notes: 1. VID (AC) specifies the input differential voltage |VTR -VCP| required for switching, where VTR is the true
input signal (such as CK, DQS, RDQS) and VCP is the complementary input signal (such as /CK, /DQS,
/RDQS). The minimum value is equal to VIH (AC) − VIL (AC).
2. The typical value of VIX (AC) is expected to be about 0.5 × VDDQ of the transmitting device and VIX (AC)
is expected to track variations in VDDQ. VIX (AC) indicates the voltage at which differential input signals
must cross.
3. The typical value of VOX (AC) is expected to be about 0.5 × VDDQ of the transmitting device and VOX
(AC) is expected to track variations in VDDQ. VOX (AC) indicates the voltage at which differential output
signals must cross.
VDDQ
VTR
Crossing point
VID
VIX or VOX
VCP
t
uc
VSSQ
Differential Signal Levels*1, 2
Preliminary Data Sheet E0933E30 (Ver. 3.0)
9
EDE5108AHBG, EDE5116AHBG
ODT DC Electrical Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
Parameter
Symbol
min
typ
max
Unit
Note
Rtt effective impedance value for EMRS (A6, A2) = 0, 1; 75 Ω
Rtt1 (eff)
60
75
90
Ω
1
Rtt effective impedance value for EMRS (A6, A2) = 1, 0; 150 Ω
Rtt2 (eff)
120
150
180
Ω
1
Rtt effective impedance value for EMRS (A6, A2) = 1, 1; 50 Ω
Rtt3 (eff)
40
50
60
Ω
1
Deviation of VM with respect to VDDQ/2
∆VM
−6

+6
%
1
Note: 1. Test condition for Rtt measurements.
Measurement Definition for Rtt (eff)
Apply VIH (AC) and VIL (AC) to test pin separately, then measure current I(VIH (AC)) and I(VIL (AC)) respectively.
VIH (AC), and VDDQ values defined in SSTL_18.
EO
Rtt(eff) =
VIH(AC) − VIL(AC)
I(VIH(AC)) − I(VIL(AC))
Measurement Definition for ∆VM
Measure voltage (VM) at test pin (midpoint) with no load.
∆VM =
L
2 × VM
VDDQ
− 1 × 100%
OCD Default Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
Parameter
Pull-up and pull-down mismatch
Output slew rate
typ
Pr
Output impedance
min
max
Unit
Notes
23.4
Ω
1
12.6
18
0

4
Ω
1, 2
1.5

5
V/ns
3, 4
t
uc
od
Notes: 1. Impedance measurement condition for output source DC current: VDDQ = 1.7V; VOUT = 1420mV;
(VOUT−VDDQ)/IOH must be less than 23.4Ω for values of VOUT between VDDQ and VDDQ−280mV.
Impedance measurement condition for output sink DC current: VDDQ = 1.7V; VOUT = 280mV;
VOUT/IOL must be less than 23.4Ω for values of VOUT between 0V and 280mV.
2. Mismatch is absolute value between pull up and pull down, both are measured at same temperature and
voltage.
3. Slew rate measured from VIL (AC) to VIH (AC).
4. The absolute value of the slew rate as measured from DC to DC is equal to or greater than the slew rate
as measured from AC to AC. This is guaranteed by design and characterization.
Preliminary Data Sheet E0933E30 (Ver. 3.0)
10
EDE5108AHBG, EDE5116AHBG
Pin Capacitance (TA = 25°C, VDD, VDDQ = 1.8V ± 0.1V)
Parameter
Symbol
Pins
min.
max.
Unit
Notes
CLK input pin capacitance
CCK
CK, /CK
1.0
2.0
pF
1
1.0
1.75
pF
1
CIN
/RAS, /CAS,
/WE, /CS,
CKE, ODT,
Address
1.0
2.0
pF
1
2.5
3.5
pF
2
2.5
4.0
pF
2
Input pin capacitance
-8E, -8G
-6E, -5C, -4A
Input/output pin capacitance
-8E, -8G, -6E
CI/O
-5C, -4A
DQ, DQS, /DQS,
UDQS, /UDQS,
LDQS, /LDQS,
RDQS, /RDQS, DM,
UDM, LDM
L
EO
Notes: 1. Matching within 0.25pF.
2. Matching within 0.50pF.
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
11
EDE5108AHBG, EDE5116AHBG
AC Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V, VSS, VSSQ = 0V) [DDR2-800, 667]
Frequency (Mbps)
Parameter
Symbol
/CAS latency
CL
Active to read or write command delay
tRCD
Precharge command period
tRP
Active to active/auto-refresh command time tRC
tAC
EO
DQ output access time from CK, /CK
-8E, -8G
-6E
800
667
min.
max.
min.
max.
Unit
5 (-8E)
6 (-8G)
12.5 (-8E)
15 (-8G)
12.5 (-8E)
15 (-8G)
57.5(-8E)
60 (-8G)
5 (-8E)
6 (-8G)
5
5
tCK

15

ns

15

ns

60

ns
−400
+400
−450
+450
ps
Notes
tDQSCK
−350
+350
−400
+400
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min.
(tCL, tCH)

min.
(tCL, tCH)

ps
Clock cycle time
tCK
2500
8000
3000
8000
ps
DQ and DM input hold time
tDH (base) 125

175

ps
5
DQ and DM input setup time
tDS (base) 50

100

ps
4
0.6

0.6

tCK
DQ and DM input pulse width for each input tDIPW
0.35

0.35

tCK
Data-out high-impedance time from CK,/CK tHZ

tAC max.

tAC max.
ps
Data-out low-impedance time from CK,/CK
tAC min.
tAC max.
tAC min.
tAC max.
ps
ps
L
DQS output access time from CK, /CK
Control and Address input pulse width for
each input
tIPW
tLZ
Pr

200

240
DQ hold skew factor
tQHS

300

340
tQH
tHP – tQHS 
tHP – tQHS 
ps
DQS latching rising transitions to associated
tDQSS
clock edges
−0.25
+0.25
−0.25
+0.25
tCK
DQS input high pulse width
tDQSH
0.35

0.35

tCK
tDQSL
0.35

0.35

tCK
DQS falling edge to CK setup time
tDSS
0.2

0.2

tCK
DQS falling edge hold time from CK
tDSH
0.2

0.2

tCK
Mode register set command cycle time
tMRD
2

2

tCK
Write postamble
tWPST
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.35

0.35

tCK
Address and control input hold time
tIH (base) 250

275

ps
5
Address and control input setup time
tIS (base) 175

200

ps
4
Read preamble
tRPRE
0.9
1.1
0.9
1.1
tCK
Read postamble
tRPST
0.4
0.6
0.4
0.6
tCK
Active to precharge command
tRAS
45
70000
45
70000
ns
Active to auto precharge delay
tRAP
tRCD min.

tRCD min.

ns
Active bank A to active bank B command
period
(EDE5108AH)
tRRD
7.5

7.5

ns
(EDE5116AH)
tRRD
10

10

ns
DQ/DQS output hold time from DQS
DQS input low pulse width
12
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
ps
uc
od
DQS-DQ skew for DQS and associated DQ
tDQSQ
signals
EDE5108AHBG, EDE5116AHBG
Frequency (Mbps)
Parameter
Symbol
/CAS to /CAS command delay
Write recovery time
-8E, -8G
-6E
800
667
min.
max.
min.
max.
Unit
tCCD
2

2

tCK
tWR
15

15

ns
Auto precharge write recovery + precharge
time
tDAL
(tWR/tCK) +

(tRP/tCK)
Internal write to read command delay
tWTR
7.5

7.5

ns
Internal read to precharge command delay
tRTP
7.5

7.5

ns
(tWR/tCK)+

(tRP/tCK)
tCK
Notes
1
tXSNR
tRFC + 10

tRFC + 10

ns
Exit self-refresh to a read command
tXSRD
200

200

tCK
Exit precharge power-down to any non-read
tXP
command
2

2

tCK
Exit active power-down to read command
tXARD
2

2

tCK
3
tXARDS
8 − AL

7 − AL

tCK
2, 3
tCKE
3

3

tCK
Output impedance test driver delay
tOIT
0
12
0
12
ns
MRS command to ODT update delay
tMOD
0
12
0
12
ns
tRFC
105

105

ns
tREFI

7.8

7.8
µs
tREFI

3.9

3.9
µs
tIS + tCK +
tIH

tIS + tCK +
tIH

ns
EO
Exit self-refresh to a non-read command
Exit active power-down to read command
(slow exit/low power mode)
CKE minimum pulse width (high and low
pulse width)
L
Auto-refresh to active/auto-refresh
command time
Average periodic refresh interval
(0°C ≤ TC ≤ +85°C)
(+85°C < TC ≤ +95°C)
Minimum time clocks remains ON after CKE
tDELAY
asynchronously drops low
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
13
EDE5108AHBG, EDE5116AHBG
AC Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V, VSS, VSSQ = 0V) [DDR2-533, 400]
Frequency (Mbps)
Parameter
Symbol
-5C
-4A
533
400
min.
max.
min.
max.
Unit
CL
4
5
3
5
tCK
Active to read or write command delay
tRCD
15

15

ns
Precharge command period
tRP
15

15

ns
Active to active/auto-refresh command time
tRC
60

55

ns
DQ output access time from CK, /CK
tAC
−500
+500
−600
+600
ps
DQS output access time from CK, /CK
tDQSCK
−450
+450
−500
+500
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min.
(tCL, tCH)

min.
(tCL, tCH)

ps
Clock cycle time
tCK
3750
8000
5000
8000
ps
tDH (base) 225

275

ps
tDH1
(base)
–25

+25

ps
tDS (base) 100

150

ps
tDS1
(base)
–25

+25

ps
tIPW
0.6

0.6

tCK
0.35

EO
/CAS latency
L
DQ and DM input hold time
(differential strobe)
DQ and DM input hold time
(single-ended strobe)
DQ and DM input setup time
(differential strobe)
DQ and DM input setup time
(single-ended strobe)
Control and Address input pulse width for
each input
0.35

tCK
Data-out high-impedance time from CK,/CK tHZ

tAC max.

tAC max.
ps
Data-out low-impedance time from CK,/CK
tLZ
tAC min.
tAC max.
tAC min.
tAC max.
ps
DQS-DQ skew for DQS and associated DQ
signals
tDQSQ

300

350
ps
DQ hold skew factor
tQHS

400

450
ps
tQH
tHP – tQHS 
DQ and DM input pulse width for each input tDIPW
Pr
DQ/DQS output hold time from DQS
tHP – tQHS 
Notes
5
4
ps
−0.25
+0.25
−0.25
+0.25
tCK
DQS input high pulse width
tDQSH
0.35

0.35

tCK
DQS input low pulse width
tDQSL
0.35

0.35

tCK
DQS falling edge to CK setup time
tDSS
0.2

0.2

tCK
od
DQS latching rising transitions to associated
tDQSS
clock edges
tDSH
0.2

0.2

tCK
Mode register set command cycle time
tMRD
2

2

tCK
Write postamble
tWPST
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.35

0.35

tCK
Address and control input hold time
tIH (base) 375

475

ps
5
Address and control input setup time
tIS (base) 250

350

ps
4
uc
DQS falling edge hold time from CK
tRPRE
0.9
1.1
0.9
1.1
tCK
Read postamble
tRPST
0.4
0.6
0.4
0.6
tCK
Active to precharge command
tRAS
45
70000
40
70000
ns
Active to auto precharge delay
tRAP
tRCD min.

tRCD min.

Preliminary Data Sheet E0933E30 (Ver. 3.0)
14
t
Read preamble
ns
EDE5108AHBG, EDE5116AHBG
Frequency (Mbps)
-5C
-4A
533
400
Parameter
Symbol
min.
max.
min.
max.
Unit
Active bank A to active bank B command
period
(EDE5108AH)
tRRD
7.5

7.5

ns
(EDE5116AH)
tRRD
10

10

ns
/CAS to /CAS command delay
tCCD
2

2

tCK
Write recovery time

15

ns
15
tDAL
(tWR/tCK)+

(tRP/tCK)
Internal write to read command delay
tWTR
7.5

10

ns
Internal read to precharge command delay
tRTP
7.5

7.5

ns
Exit self-refresh to a non-read command
tXSNR
tRFC + 10

tRFC + 10

ns
Exit self-refresh to a read command
tXSRD
EO
tWR
Auto precharge write recovery + precharge
time
(tWR/tCK)+

(tRP/tCK)
tCK
Notes
1
200

200

tCK
Exit precharge power-down to any non-read
tXP
command
2

2

tCK
Exit active power-down to read command
tXARD
2

2

tCK
3
tXARDS
6 − AL

6 − AL

tCK
2, 3
tCKE
3

3

tCK
L
Exit active power-down to read command
(slow exit/low power mode)
CKE minimum pulse width (high and low
pulse width)
Output impedance test driver delay
tOIT
0
12
0
12
ns
MRS command to ODT update delay
tMOD
0
12
0
12
ns
105

105

ns

7.8

7.8
µs

3.9

3.9
µs

tIS + tCK +
tIH

ns
Pr
Auto-refresh to active/auto-refresh command
tRFC
time
Average periodic refresh interval
tREFI
(0°C ≤ TC ≤ +85°C)
(+85°C < TC ≤ +95°C)
tREFI
Minimum time clocks remains ON after CKE
tDELAY
asynchronously drops low
For each of the terms above, if not already an integer, round to the next higher integer.
AL: Additive Latency.
MRS A12 bit defines which active power-down exit timing to be applied.
The figures of Input Waveform Timing 1 and 2 are referenced from the input signal crossing at the
VIH(AC) level for a rising signal and VIL(AC) for a falling signal applied to the device under test.
5. The figures of Input Waveform Timing 1 and 2 are referenced from the input signal crossing at the
VIH(DC) level for a rising signal and VIL(DC) for a falling signal applied to the device under test.
od
Notes: 1.
2.
3.
4.
tIS + tCK +
tIH
CK
DQS
/CK
/DQS
tDH
tDS
tIS
tDH
uc
tDS
tIH
tIS
tIH
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VSS
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VSS
t
Input Waveform Timing 1 (tDS, tDH)
Input Waveform Timing 2 (tIS, tIH)
Preliminary Data Sheet E0933E30 (Ver. 3.0)
15
EDE5108AHBG, EDE5116AHBG
ODT AC Electrical Characteristics
Parameter
Symbol
min
max
Unit
ODT turn-on delay
tAOND
2
2
tCK
ODT turn-on
-8E, -8G, -6E
tAON
tAC(min)
tAC(max) + 700
ps
1
1
tAON
tAC(min)
tAC(max) + 1000
ps
ODT turn-on (power-down mode)
tAONPD
tAC(min) + 2000
2tCK + tAC(max) + 1000
ps
ODT turn-off delay
tAOFD
2.5
2.5
tCK
ODT turn-off
tAOF
tAC(min)
tAC(max) + 600
ps
ODT turn-off (power-down mode)
tAOFPD
tAC(min) + 2000
2.5tCK + tAC(max) + 1000
ps
ODT to power-down entry latency
tANPD
3
3
tCK
tAXPD
8
8
tCK
-5C, -4A
EO
ODT power-down exit latency
Notes
2
Notes: 1. ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on.
ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND.
2. ODT turn off time min is when the device starts to turn off ODT resistance.
ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
AC Input Test Conditions
Symbol
Value
Unit
Notes
Input reference voltage
VREF
0.5 × VDDQ
V
1
Input signal maximum peak to peak swing
VSWING(max.)
1.0
V
1
Input signal minimum slew rate
SLEW
1.0
V/ns
2, 3
L
Parameter
Pr
Notes: 1. Input waveform timing is referenced to the input signal crossing through the VREF level applied to the
device under test.
2. The input signal minimum slew rate is to be maintained over the range from VIL(DC) (max.) to VIH(AC)
(min.) for rising edges and the range from VIH(DC) (min.) to VIL(AC) (max.) for falling edges as shown in
the below figure.
3. AC timings are referenced with input waveforms switching from VIL(AC) to VIH(AC) on the positive
transitions and VIH(AC) to VIL(AC) on the negative transitions.
Start of rising edge input timing
Start of falling edge input timing
od
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VSWING(max.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VIH (DC)(min.) − VIL (AC)(max.)
Rising slew =
∆TF
VIH (AC) min. − VIL (DC)(max.)
AC Input Test Signal Wave forms
Measurement point
VTT
RT =25 Ω
Output Load
Preliminary Data Sheet E0933E30 (Ver. 3.0)
16
∆TR
t
DQ
uc
Falling slew =
VSS
∆TR
∆TF
EDE5108AHBG, EDE5116AHBG
Input Slew Rate Derating
For all input signals the total tIS, tDS (setup time) and tIH, tDH (hold time) required is calculated by adding the data
sheet tIS (base), tDS (base) and tIH (base), tDH (base) value to the ∆tIS, ∆tDS and ∆tIH, ∆tDH derating value
respectively.
Example: tDS (total setup time) = tDS (base) + ∆tDS.
EO
Setup (tIS, tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF
(DC) and the first crossing of VIH (AC) min. Setup (tIS, tDS) nominal slew rate for a falling signal is defined as the
slew rate between the last crossing of VREF (DC) and the first crossing of VIL (AC) max. If the actual signal is
always earlier than the nominal slew rate line between shaded ‘VREF (DC) to AC region’, use nominal slew rate for
derating value (See the figure of Slew Rate Definition Nominal).
If the actual signal is later than the nominal slew rate line anywhere between shaded ‘VREF (DC) to AC region’, the
slew rate of a tangent line to the actual signal from the AC level to DC level is used for derating value (see the figure
of Slew Rate Definition Tangent).
L
Hold (tIH, tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of
VIL (DC) max. and the first crossing of VREF (DC). Hold (tIH, tDH) nominal slew rate for a falling signal is defined
as the slew rate between the last crossing of VIH (DC) min. and the first crossing of VREF (DC). If the actual signal
is always later than the nominal slew rate line between shaded ‘DC level to VREF (DC) region’, use nominal slew
rate for derating value (See the figure of Slew Rate Definition Nominal).
If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘DC to VREF (DC) region’,
the slew rate of a tangent line to the actual signal from the DC level to VREF (DC) level is used for derating value
(see the figure of Slew Rate Definition Tangent).
Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached
VIH/IL (AC) at the time of the rising clock transition) a valid input signal is still required to complete the transition and
reach VIH/IL (AC).
Pr
For slew rates in between the values listed in the tables below, the derating values may obtained by linear
interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
[Derating Values of tDS/tDH with Differential DQS (DDR2-400, 533)]
DQS, /DQS differential slew rate
3.0 V/ns
2.0 V/ns
1.8 V/ns
od
4.0 V/ns
1.6 V/ns
1.4 V/ns
1.2 V/ns
1.0 V/ns
0.8 V/ns
∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH Unit
+125 +45
+125 +45
+125 +45












ps
1.5
+83
+21
+83
+21
+83
+21
+95
+33










ps
1.0
0
0
0
0
0
0
+12
+12
+24
+24








ps
0.9


−11
−14
−11
−14
+1
−2
+13
+10
+25
+22






ps
0.8




−25
−31
−13
−19
−1
−7
11
+5
+23
+17




ps
0.7






−31
−42
−19
−30
−7
−18
+5
−6
+17
+6


ps
0.6








−43
−59
−31
−47
0.5










−74
−89
0.4












uc
DQ
slew
rate
(V/ns)
2.0
−19
−35
−7
−23
+5
−11
ps
−62
−77
−50
−65
−38
−53
ps
−127 −140 −115 −128 −103 −116 ps
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
17
EDE5108AHBG, EDE5116AHBG
[Derating Values of tDS/tDH with Differential DQS (DDR2-667, 800)]
DQS, /DQS differential slew rate
4.0 V/ns
3.0 V/ns
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4 V/ns
1.2 V/ns
1.0 V/ns
0.8 V/ns
∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH ∆tDS ∆tDH Unit
2.0
+100 +45
+100 +45
+100 +45












ps
1.5
+67
+21
+67
+21
+67
+21
+79
+33










ps
1.0
0
0
0
0
0
0
+12
+12
+24
+24








ps
0.9


−5
−14
−5
−14
+7
−2
+19
+10
+31
+22






ps
0.8




−13
−31
−1
−19
+11
−7
+23
+5
+35
+17




ps
0.7






−10
−42
+2
−30
+14
−18
+26
−6
+38
+6


ps
0.6



EO
DQ
slew
rate
(V/ns)





−10
−59
+2
−47
+14
−35
+26
−23
+38
−11
ps
0.5










−24
−89
−12
−77
0
−65
+12
−53
ps
0.4












−52
−140 −40
−128 −28
−116 ps
[Derating Values of tDS1/tDH1 with Single-Ended DQS (DDR2-400, 533)]
DQS, /DQS single-ended slew rate
2.0 V/ns
1.5 V/ns
1.0V/ns
0.9V/ns
0.8V/ns
0.7 V/ns
0.6 V/ns
0.5 V/ns
0.4 V/ns
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
Unit
tDS1 tDH1 tDS1 tDH1 tDS1 tDH1 tDS1 tDH1 tDS1 tDH1 tDS1 tDH1 tDS1 tDH1 tDS1 tDH1 tDS1 tDH1
L
+188 +188 +167 +146 +125 +63












ps
1.5
+146 +167 +125 +125 +83
+42
+81
+43










ps
1.0
+63
+125 +42
+83
0
−2
+1
−7
−13








ps
0.9


+31
+69
−11
−14
−13
−13
−18
−27
−29
−45






ps
0.8




−25
−31
−27
−30
−32
−44
−43
−62
−60
−86




ps
0.7






−45
−53
−50
−67
−61
−85
−78
−109 −108 −152 

ps
0.6








−74
−96
−85
−114 −102 −138 −132 −181 −183 −246 ps
0.5










−128 −156 −145 −180 −175 −223 −226 −288 ps
0.4











0

−210 −243 −240 −286 −291 −351 ps
t
uc
od
Pr
DQ
slew
rate
(V/ns)
2.0
Preliminary Data Sheet E0933E30 (Ver. 3.0)
18
EDE5108AHBG, EDE5116AHBG
[Derating Values of tIS/tIH (DDR2-400, DDR2-533)]
CK, /CK Differential Slew Rate
2.0 V/ns
1.0 V/ns
∆tIS
∆tIH
∆tIS
∆tIH
∆tIS
∆tIH
Unit Notes
4.0
+187
+94
+217
+124
+247
+154
ps
3.5
+179
+89
+209
+119
+239
+149
ps
3.0
+167
+83
+197
+113
+227
+143
ps
2.5
+150
+75
+180
+105
+210
+135
ps
2.0
+125
+45
+155
+75
+185
+105
ps
1.5
+83
+21
+113
+51
+143
+81
ps
1.0
0
0
+30
+30
+60
60
ps
0.9
−11
−14
+19
+16
+49
+46
ps
0.8
−25
−31
+5
−1
+35
+29
ps
0.7
−43
−54
−13
−24
+17
+6
ps
0.6
−67
−83
−37
−53
−7
−23
ps
0.5
−110
−125
−80
−95
−50
−65
ps
0.4
−175
−188
−145
−158
−115
−128
ps
0.3
−285
−292
−255
−262
−225
−232
ps
0.25
−350
−375
−320
−345
−290
−315
ps
0.2
−525
−500
−495
−470
−465
−440
ps
0.15
−800
−708
−770
−678
−740
−648
ps
0.1
−1450
−1125
−1420
−1095
−1390
−1065
ps
EO
Command/address
slew rate (V/ns)
1.5 V/ns
L
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
19
EDE5108AHBG, EDE5116AHBG
[Derating Values of tIS/tIH (DDR2-667, DDR2-800)]
CK, /CK Differential Slew Rate
2.0 V/ns
1.0 V/ns
∆tIS
∆tIH
∆tIS
∆tIH
∆tIS
∆tIH
Unit
4.0
+150
+94
+180
+124
+210
+154
ps
3.5
+143
+89
+173
+119
+203
+149
ps
3.0
+133
+83
+163
+113
+193
+143
ps
2.5
+120
+75
+150
+105
+180
+135
ps
2.0
+100
+45
+130
+75
+160
+105
ps
1.5
+67
+21
+97
+51
+127
+81
ps
1.0
0
0
+30
+30
+60
+60
ps
0.9
−5
−14
+25
+16
+55
+46
ps
0.8
−13
−31
+17
−1
+47
+29
ps
0.7
−22
−54
+8
−24
+38
+6
ps
0.6
−34
−83
−4
−53
+26
−23
ps
0.5
−60
−125
−30
−95
0
−65
ps
0.4
−100
−188
−70
−158
−40
−128
ps
0.3
−168
−292
−138
−262
−108
−232
ps
0.25
−200
−375
−170
−345
−140
−315
ps
0.2
−325
−500
−295
−470
−265
−440
ps
0.15
−517
−708
−487
−678
−457
−648
ps
0.1
−1000
−1125
−970
−1095
−940
−1065
ps
EO
Command/address
slew rate (V/ns)
1.5 V/ns
Notes
L
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
20
EDE5108AHBG, EDE5116AHBG
Single-ended DQS
VDDQ
VIH (AC) min.
VIH (DC) min.
VREF (DC)
VIL (DC) max.
VIL (AC) max.
VSS
DQS
Differential DQS, /DQS
CK, /CK
DQS
CK
tDS1
tDH1
tDS1
tDH1
/DQS
/CK
EO
tDS
tIS
tDH
tIH
tDS
tIS
tDH
tIH
VDD
VIH (AC) min.
L
VREF to AC
region
VIH (DC) min.
VIL (DC) max.
VIL (AC) max.
VSS
∆TFS
∆TFH
uc
=
VREF to AC
region
∆TRH ∆TRS
VREF (DC) - VIL (AC) max.
Setup slew rate
=
Falling signal
∆TFS
Hold slew rate
Rising signal
nominal
slew rate
DC to VREF
region
od
Pr
VREF (DC)
DC to VREF
region
nominal
slew rate
VIH (AC) min. - VREF (DC)
Setup slew rate
=
Rising signal
∆TRS
VREF (DC) - VIL (DC) max.
Hold slew rate
Falling signal
∆TRH
Preliminary Data Sheet E0933E30 (Ver. 3.0)
21
VIH (DC) min. - VREF (DC)
∆TFH
t
Slew Rate Definition Nominal
=
EDE5108AHBG, EDE5116AHBG
Single-ended DQS
DQS
VDDQ
VIH (AC) min.
VIH (DC) min.
VREF (DC)
VIL (DC) max.
VIL (AC) max.
VSS
Differential DQS, /DQS
CK, /CK
DQS
CK
tDS1
tDH1
tDS1
tDH1
tDS
tIS
tDH
tIH
/DQS
/CK
EO
tDS
tIS
tDH
tIH
VDD
VIH (AC) min.
VREF to AC
region
L
nominal
line
nominal
line
VIH (DC) min.
VIL (DC) max.
nominal
line
VIL (AC) max.
VSS
∆TFS
∆TRH
VREF to AC
region
∆TRS
∆TFH
uc
tangent line [VREF (DC) - VIL (AC) max.]
Setup slew rate
=
Falling signal
∆TFS
=
DC to VREF
region
od
nominal
line
Hold slew rate
Rising signal
tangent
line
Pr
VREF (DC)
DC to VREF
region
tangent
line
tangent line [VIH (AC) min. - VREF (DC)]
Setup slew rate
=
Rising signal
∆TRS
tangent line [VREF (DC) - VIL (DC) max.]
Hold slew rate
Falling signal
∆TRH
Slew Rate Definition Tangent
=
tangent line [VIH (DC) min. - VREF (DC)]
∆TFH
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
22
EDE5108AHBG, EDE5116AHBG
Clock
generator
Block Diagram
Bank 3
Bank 2
Bank 1
A0 to A13, BA0, BA1
Memory cell array
Bank 0
Control logic
Sense amp.
L
Command decoder
EO
/CS
/RAS
/CAS
/WE
Mode
register
Row
address
buffer
and
refresh
counter
Row decoder
CK
/CK
CKE
Column decoder
Column
address
buffer
and
burst
counter
Data control circuit
Latch circuit
Pr
DLL
CK, /CK
Input & Output buffer
DQS, /DQS
RDQS, /RDQS
ODT
DM
DQ
t
uc
od
Preliminary Data Sheet E0933E30 (Ver. 3.0)
23
EDE5108AHBG, EDE5116AHBG
Pin Function
CK, /CK (input pins)
CK and /CK are differential clock inputs. All address and control input signals are sampled on the crossing of the
positive edge of CK and negative edge of /CK. Output (read) data is referenced to the crossings of CK and /CK
(both directions of crossing).
/CS (input pin)
All commands are masked when /CS is registered high. /CS provides for external rank selection on systems with
multiple ranks. /CS is considered part of the command code.
/RAS, /CAS, /WE (input pins)
/RAS, /CAS and /WE (along with /CS) define the command being entered.
EO
A0 to A13 (input pins)
Provided the row address for Active commands and the column address and Auto Precharge bit for Read/Write
commands to select one location out of the memory array in the respective bank. The address inputs also provide
the op-code during mode register set commands.
[Address Pins Table]
Part number
EDE5116AHBG
Row address
Column address
L
EDE5108AHBG
Address (A0 to A13)
AX0 to AX13
AY0 to AY9
AX0 to AX12
AY0 to AY9
Note
1
Note: 1. A13 pin is NC for × 16 organization.
Pr
A10 (AP) (input pin)
A10 is sampled during a precharge command to determine whether the precharge applies to one bank (A10 = low)
or all banks (A10 = high). If only one bank is to be precharged, the bank is selected by BA0, BA1.
[Bank Select Signal Table]
BA0
L
Bank 1
H
Bank 2
L
Bank 3
H
BA1
L
L
H
uc
Bank 0
od
BA0, BA1 (input pins)
BA0 and BA1 define to which bank an active, read, write or precharge command is being applied. BA0 also
determines if the mode register or extended mode register is to be accessed during a MRS or EMRS (1), EMRS (2)
cycle.
H
Remark: H: VIH. L: VIL.
t
CKE (input pin)
CKE high activates, and CKE low deactivates, internal clock signals and device input buffers and output drivers.
Taking CKE low provides precharge power-down and Self Refresh operation (all banks idle), or active power-down
(row active in any bank). CKE is synchronous for power-down entry and exit, and for self-refresh entry. CKE is
asynchronous for self-refresh exit. CKE must be maintained high throughout read and write accesses. Input buffers,
excluding CK, /CK and CKE are disabled during power-down. Input buffers, excluding CKE, are disabled during selfrefresh.
Preliminary Data Sheet E0933E30 (Ver. 3.0)
24
EDE5108AHBG, EDE5116AHBG
DM, UDM and LDM (input pins)
DM is an input mask signal for write data. Input data is masked when DM is sampled high coincident with that input
data during a Write access. DM is sampled on both edges of DQS. Although DM pins are input only, the DM
loading matches the DQ and DQS loading.
For ×8 configuration, DM function will be disabled when RDQS function is enabled by EMRS.
In × 16 configuration, UDM controls upper byte (DQ8 to DQ15) and LDM controls lower byte (DQ0 to DQ7). In this
datasheet, DM represents UDM and LDM.
DQ (input/output pins)
Bi-directional data bus.
EO
DQS, /DQS UDQS, /UDQS, LDQS, /LDQS (input/output pins)
Output with read data, input with write data for source synchronous operation. Edge-aligned with read data,
centered in write data. Used to capture write data. /DQS can be disabled by EMRS.
In × 16 configuration, UDQS, /UDQS and LDQS, /LDQS control upper byte (DQ8 to DQ15) and lower byte (DQ0 to
DQ7). In this datasheet, DQS represents UDQS and LDQS, /DQS represents /UDQS and /LDQS.
RDQS, /RDQS (output pins)
Differential Data Strobe for READ operation only. DM and RDQS functions are switch able by EMRS. These pins
exist only in ×8 configuration. /RDQS output will be disabled when /DQS is disabled by EMRS.
L
ODT (input pins)
ODT (On Die Termination control) is a registered high signal that enables termination resistance internal to
the DDR2 SDRAM. When enabled, ODT is only applied to each DQ, DQS, /DQS, RDQS, /RDQS, and DM signal for
× 8 configurations. For × 16 configuration, ODT is applied to each DQ, UDQS, /UDQS, LDQS, /LDQS, UDM, and
LDM signal. The ODT pin will be ignored if the Extended Mode Register (EMRS) is programmed to disable ODT.
Any time the EMRS enables the ODT function; ODT may not be driven high until eight clocks after the EMRS has
been enabled.
Pr
VDD, VSS, VDDQ, VSSQ (power supply)
VDD and VSS are power supply pins for internal circuits. VDDQ and VSSQ are power supply pins for the output
buffers.
VDDL and VSSDL (power supply)
VDDL and VSSDL are power supply pins for DLL circuits.
t
uc
od
VREF (Power supply)
SSTL_18 reference voltage: (0.50 ± 0.01) × VDDQ
Preliminary Data Sheet E0933E30 (Ver. 3.0)
25
EDE5108AHBG, EDE5116AHBG
Command Operation
Command Truth Table
The DDR2 SDRAM recognizes the following commands specified by the /CS, /RAS, /CAS, /WE and address pins.
CKE
Function
Previou Current
Symbol s cycle cycle
/CS
/RAS /CAS /WE BA0
BA1
A13 to
A11
A10
Mode register set
MRS
H
H
L
L
L
L
L
L
MRS OPCODE
1
EMRS
H
H
L
L
L
L
H
L
EMRS (1) OPCODE
1
EMRS
H
H
L
L
L
L
L
H
EMRS (2) OPCODE
1
Extended mode
register set (1)
Extended mode
register set (2)
A0 to
A9
Notes
REF
H
H
L
L
L
H
×
×
×
×
×
1
Self-refresh entry
SELF
H
L
L
L
L
H
×
×
×
×
×
1
Self-refresh exit
SELFX L
H
H
×
×
×
×
×
×
×
×
1, 6
L
H
L
H
H
H
×
×
×
×
×
Single bank precharge
PRE
H
H
L
L
H
L
BA
×
L
×
1, 2
Precharge all banks
PALL
H
H
L
L
H
L
×
×
H
×
1
Bank activate
ACT
H
H
L
L
H
H
BA
RA
Write
WRIT
H
H
L
H
L
L
BA
CA
L
CA
1, 2, 3
Write with auto precharge
WRITA H
H
L
H
L
L
BA
CA
H
CA
1, 2, 3
Read
L
EO
Auto-refresh
1, 2
H
H
L
H
L
H
BA
CA
L
CA
1, 2, 3
Read with auto precharge
READA H
H
L
H
L
H
BA
CA
H
CA
1, 2, 3
No operation
NOP
H
×
L
H
H
H
×
×
×
×
×
1
Device deselect
DESL
H
H
Power-down mode entry
PDEN
PDEX
×
×
×
×
×
×
×
×
1
H
L
×
H
×
×
×
×
×
×
×
×
1, 4
H
L
L
H
H
H
×
×
×
×
×
L
H
H
×
×
×
×
×
×
×
×
L
H
L
H
H
H
×
×
×
×
×
Pr
Power-down mode exit
READ
×
1, 4
t
uc
od
Remark: H = VIH. L = VIL. × = VIH or VIL. BA = Bank Address, RA = Row Address, CA = Column Address
Notes: 1. All DDR2 commands are defined by states of /CS, /RAS, /CAS, /WE and CKE at the rising edge of the
clock.
2. Bank select (BA0, BA1), determine which bank is to be operated upon.
3. Burst reads or writes should not be terminated other than specified as ″Reads interrupted by a Read″ in
burst read command [READ] or ″Writes interrupted by a Write″ in burst write command [WRIT].
4. The power-down mode does not perform any refresh operations. The duration of power-down is therefore
limited by the refresh requirements of the device. One clock delay is required for mode entry and exit.
5. The state of ODT does not affect the states described in this table. The ODT function is not available
during self-refresh.
6. Self-refresh exit is asynchronous.
Preliminary Data Sheet E0933E30 (Ver. 3.0)
26
EDE5108AHBG, EDE5116AHBG
CKE Truth Table
CKE
*3
Previous
1
cycle (n-1)*
Current
*1
cycle (n)
Command(n)
/CS, /RAS, /CAS, /WE
Operation (n)
L
L
×
Maintain power-down
11, 13, 15
L
H
DESL or NOP
Power-down exit
4, 8, 11, 13
L
L
×
Maintain self-refresh
11, 15
L
H
DESL or NOP
Self-refresh exit
4, 5, 9
Bank Active
H
L
DESL or NOP
Active power-down entry
4, 8, 10, 11, 13
All banks idle
H
L
DESL or NOP
Precharge power-down entry
4, 8, 10, 11, 13
H
L
SELF
Self-refresh entry
6, 9, 11, 13
H
Refer to the Command Truth Table
Current state*
2
Power-down
Self-refresh
EO
Any state other than
listed above
H
*3
Notes
7
L
Remark: H = VIH. L = VIL. × = Don’t care
Notes: 1. CKE (n) is the logic state of CKE at clock edge n; CKE (n−1) was the state of CKE at the previous clock
edge.
2. Current state is the state of the DDR SDRAM immediately prior to clock edge n.
3. Command (n) is the command registered at clock edge n, and operation (n) is a result of Command (n).
4. All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this
document.
5. On self-refresh exit, [DESL] or [NOP] commands must be issued on every clock edge occurring during the
tXSNR period. Read commands may be issued only after tXSRD (200 clocks) is satisfied.
6. Self-refresh mode can only be entered from the all banks idle state.
7. Must be a legal command as defined in the command truth table.
8. Valid commands for power-down entry and exit are [NOP] and [DESL] only.
9. Valid commands for self-refresh exit are [NOP] and [DESL] only.
10. Power-down and self-refresh can not be entered while read or write operations, (extended) mode register
set operations or precharge operations are in progress. See section Power Down and Self Refresh
Command for a detailed list of restrictions.
11. Minimum CKE high time is 3 clocks; minimum CKE low time is 3 clocks.
12. The state of ODT does not affect the states described in this table. The ODT function is not available
during self-refresh. See section ODT (On Die Termination).
13. The power-down does not perform any refresh operations. The duration of power-down mode is therefore
limited by the refresh requirements outlined in section automatic refresh command.
14. CKE must be maintained high while the SDRAM is in OCD calibration mode.
15. “×” means “don’t care” (including floating around VREF) in self-refresh and power-down. However ODT
must be driven high or low in power-down if the ODT function is enabled (bit A2 or A6 set to “1” in
EMRS(1) ).
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
27
EDE5108AHBG, EDE5116AHBG
Function Truth Table
The following tables show the operations that are performed when each command is issued in each state of the
DDR2 SDRAM.
Current state
/CS
/RAS /CAS /WE
Address
Idle
H
×
×
×
L
H
H
H
L
H
L
L
H
L
L
L
L
H
Operation
Notes
×
DESL
Nop
×
NOP
Nop
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
1
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1
H
H
BA, RA
ACT
Row activating
L
BA
PRE
Nop
L
H
L
A10 (AP)
PALL
Nop
EO
L
Command
L
L
L
H
×
REF
Auto-refresh
2
L
L
L
H
×
SELF
Self refresh
2
L
L
L
L
BA, MRS-OPCODE
MRS
Mode register accessing
2
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
Extended mode register accessing 2
H
×
×
×
×
DESL
Nop
Bank(s) active
H
H
H
×
NOP
Nop
H
L
H
BA, CA, A10 (AP)
READ/READA
Begin Read
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
Begin Write
L
L
L
L
H
H
BA, RA
ACT
ILLEGAL
L
H
L
BA
PRE
Precharge
L
L
H
L
A10 (AP)
PALL
Precharge all banks
L
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
×
×
×
×
DESL
L
H
H
H
×
NOP
L
H
L
H
BA, CA, A10 (AP)
L
H
L
L
L
L
H
H
L
L
H
L
BA
1
ILLEGAL
Continue burst to end -> Row
active
Continue burst to end -> Row
active
od
H
Pr
Read
L
L
READ/READA
Burst interrupt
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1
BA, RA
ACT
ILLEGAL
1
PRE
ILLEGAL
1
L
H
L
A10 (AP)
L
L
H
×
PALL
ILLEGAL
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
uc
L
L
1, 4
ILLEGAL
ILLEGAL
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
28
EDE5108AHBG, EDE5116AHBG
Current state
/CS
/RAS /CAS /WE
Address
Command
Write
H
×
×
×
×
DESL
L
H
H
H
×
NOP
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
Burst interrupt
1, 4
L
L
H
H
BA, RA
ACT
ILLEGAL
1
L
L
H
L
BA
PRE
ILLEGAL
1
Continue burst to end
-> Write recovering
Continue burst to end
-> Write recovering
1
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
BA, EMRS-OPCODE EMRS (1) (2)
ILLEGAL
H
×
×
×
×
DESL
L
H
H
H
×
NOP
Continue burst to end ->
Precharging
Continue burst to end ->
Precharging
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
1
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1
ILLEGAL
1
1
L
L
L
H
H
BA, RA
ACT
L
L
H
L
BA
PRE
ILLEGAL
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
L
L
H
×
×
L
H
H
L
H
L
Pr
Write with auto
Precharge
Note
L
EO
Read with auto
precharge
Operation
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
BA, EMRS-OPCODE EMRS (1) (2)
×
×
DESL
H
×
NOP
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
1
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1
L
L
H
H
BA, RA
ACT
ILLEGAL
1
L
L
H
L
BA
PRE
ILLEGAL
1
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
L
H
×
L
L
L
H
×
SELF
L
L
L
L
BA, MRS-OPCODE
MRS
L
L
L
L
BA, EMRS-OPCODE EMRS (1) (2)
ILLEGAL
od
Continue burst to end
->Write recovering with auto
precharge
Continue burst to end
->Write recovering with auto
precharge
ILLEGAL
uc
REF
ILLEGAL
ILLEGAL
ILLEGAL
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
29
EDE5108AHBG, EDE5116AHBG
/CS
/RAS /CAS /WE
Address
Command
Operation
Precharging
H
×
×
×
×
DESL
Nop -> Enter idle after tRP
L
H
H
H
×
NOP
Nop -> Enter idle after tRP
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
1
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1
L
L
H
H
BA, RA
ACT
ILLEGAL
1
L
L
H
L
BA
PRE
Nop -> Enter idle after tRP
L
L
H
L
A10 (AP)
PALL
Nop -> Enter idle after tRP
L
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
EO
Current state
Row activating
ILLEGAL
Nop -> Enter bank active after
tRCD
Nop -> Enter bank active after
tRCD
H
×
×
×
×
DESL
L
H
H
H
×
NOP
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
1, 5
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1, 5
L
L
H
H
1
BA, RA
ACT
ILLEGAL
L
L
H
L
BA
PRE
ILLEGAL
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
Pr
Write recovering
Note
L
BA, EMRS-OPCODE
×
×
L
H
H
L
H
L
L
H
L
L
L
H
L
L
H
L
BA
ILLEGAL
Nop -> Enter bank active after
tWR
Nop -> Enter bank active after
tWR
×
×
DESL
H
×
NOP
H
BA, CA, A10 (AP)
READ/READA
L
BA, CA, A10 (AP)
WRIT/WRITA
New write
H
BA, RA
ACT
ILLEGAL
1
PRE
ILLEGAL
1
L
H
L
A10 (AP)
L
L
H
×
PALL
ILLEGAL
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
BA, EMRS-OPCODE
EMRS (1) (2)
1, 6
uc
L
L
ILLEGAL
od
H
EMRS (1) (2)
ILLEGAL
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
30
EDE5108AHBG, EDE5116AHBG
Current state
/CS
/RAS /CAS /WE
Address
Command
Operation
Write recovering
with auto
precharge
H
×
×
×
×
DESL
Nop -> Precharging after tWR
L
H
H
H
×
NOP
Nop -> Precharging after tWR
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
1
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
1
L
L
H
H
BA, RA
ACT
ILLEGAL
1
L
L
H
L
BA
PRE
ILLEGAL
1
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
L
H
×
REF
ILLEGAL
EO
Refresh
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
ILLEGAL
H
×
×
×
×
DESL
Nop -> Enter idle after tRFC
L
H
H
H
×
NOP
Nop -> Enter idle after tRFC
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
L
L
H
H
BA, RA
ACT
ILLEGAL
BA
PRE
ILLEGAL
L
L
L
L
H
L
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
ILLEGAL
H
×
×
×
×
DESL
Nop -> Enter idle after tMRD
L
H
H
H
×
NOP
Nop -> Enter idle after tMRD
L
H
L
H
BA, CA, A10 (AP)
READ/READA
ILLEGAL
L
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
L
L
H
H
BA, RA
ACT
ILLEGAL
L
L
H
L
BA
PRE
ILLEGAL
L
H
L
A10 (AP)
L
L
H
×
PALL
ILLEGAL
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
BA, EMRS-OPCODE
EMRS (1) (2)
uc
L
L
od
Pr
Mode register
accessing
Note
ILLEGAL
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
31
EDE5108AHBG, EDE5116AHBG
Current state
/CS
/RAS /CAS /WE
Address
Command
Operation
Extended Mode
H
×
×
×
×
DESL
Nop -> Enter idle after tMRD
register accessing L
H
H
H
×
NOP
Nop -> Enter idle after tMRD
H
L
H
BA, CA, A10 (AP)
READ/READA ILLEGAL
H
L
L
BA, CA, A10 (AP)
WRIT/WRITA
ILLEGAL
L
L
H
H
BA, RA
ACT
ILLEGAL
L
L
H
L
BA
PRE
ILLEGAL
L
L
H
L
A10 (AP)
PALL
ILLEGAL
L
L
L
H
×
REF
ILLEGAL
L
L
L
H
×
SELF
ILLEGAL
L
L
L
L
BA, MRS-OPCODE
MRS
ILLEGAL
L
L
L
L
BA, EMRS-OPCODE
EMRS (1) (2)
ILLEGAL
EO
L
L
H = VIH. L = VIL. × = VIH or VIL
This command may be issued for other banks, depending on the state of the banks.
All banks must be in "IDLE".
All AC timing specs must be met.
Only allowed at the boundary of 4 bits burst. Burst interruptions at other timings are illegal.
Available in case tRCD is satisfied by AL setting.
Available in case tWTR is satisfied.
L
Remark:
Notes: 1.
2.
3.
4.
5.
6.
Note
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
32
EDE5108AHBG, EDE5116AHBG
Simplified State Diagram
INITALIZATION
SEQUENCE
OCD
CALIBRATION
CKE_L
SELF
REFRESH
PRE
MRS
EMRS (1)
EMRS (2)
EMRS (3)
LF
SE
(E)MRS
H
E_
IDLE
CK
REF
ALL BANKS
PRECHARGED
AUTO
REFRESH
EO
CK
_L
E_L
E
CK
CK
E_H
ACT
PRECHARGE
POWER
DOWN
CKE_L
ACTIVATING
CKE_L
_L
L
CKE
ACTIVE
POWER
DOWN
CKE
_H
CKE
_L
Pr
BANK
ACTIVE
RE
AD
IT
WR
RI
W
WRITA
READA
ITA
WR
REA
DA
PRE, PALL
WRITA
READ
od
WRIT
A
READ
AD
WRITE
READ
RE
TA
WRIT
PRE, PALL
PRECHARGE
Preliminary Data Sheet E0933E30 (Ver. 3.0)
33
Automatic sequence
Command sequence
t
Simplified State Diagram
READA
uc
PRE, PALL
EDE5108AHBG, EDE5116AHBG
Operation of DDR2 SDRAM
Read and write accesses to the DDR2 SDRAM are burst oriented; accesses start at a selected location and continue
for the fixed burst length of four or eight in a programmed sequence. Accesses begin with the registration of an
active command, which is then followed by a read or write command. The address bits registered coincident with
the active command is used to select the bank and row to be accessed (BA0, BA1 select the bank; A0 to A13 select
the row). The address bits registered coincident with the read or write command are used to select the starting
column location for the burst access and to determine if the auto precharge command is to be issued.
Prior to normal operation, the DDR2 SDRAM must be initialized. The following sections provide detailed information
covering device initialization; register definition, command descriptions and device operation.
Power On and Initialization
DDR2 SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than
those specified may result in undefined operation.
EO
L
Power-Up and Initialization Sequence
The following sequence is required for power up and initialization.
1
1. Apply power and attempt to maintain CKE below 0.2 × VDDQ and ODT * at a low state (all other inputs may be
undefined.)
 VDD, VDDL and VDDQ are driven from a single power converter output, AND
 VTT is limited to 0.95V max, AND
 VREF tracks VDDQ/2.
or
 Apply VDD before or at the same time as VDDL.
 Apply VDDL before or at the same time as VDDQ.
 Apply VDDQ before or at the same time as VTT and VREF.
at least one of these two sets of conditions must be met.
2. Start clock and maintain stable condition.
3. For the minimum of 200µs after stable power and clock (CK, /CK), then apply [NOP] or [DESL] and take CKE
high.
4. Wait minimum of 400ns then issue precharge all command. [NOP] or [DESL] applied during 400ns period.
5. Issue EMRS (2) command. (To issue EMRS (2) command, provide low to BA0, high to BA1.)
6. Issue EMRS (3) command. (To issue EMRS (3) command, high to BA0 and BA1.)
7. Issue EMRS to enable DLL. (To issue DLL enable command, provide low to A0, high to BA0 and low to BA1 and
A13.)
8. Issue a mode register set command for DLL reset.
(To issue DLL reset command, provide high to A8 and low to BA0, BA1 and A13.)
9. Issue precharge all command.
10. Issue 2 or more auto-refresh commands.
11. Issue a mode register set command with low to A8 to initialize device operation. (i.e. to program operating
parameters without resetting the DLL.)
12. At least 200 clocks after step 8, execute OCD calibration (Off Chip Driver impedance adjustment). If OCD
calibration is not used, EMRS OCD default command (A9 = A8 = A7 = 1) followed by EMRS OCD calibration
mode exit command (A9 = A8 = A7 = 0) must be issued with other operating parameters of EMRS.
13. The DDR2 SDRAM is now ready for normal operation.
Note: 1. To guarantee ODT off, VREF must be valid and a low level must be applied to the ODT pin.
uc
od
Pr
tCH tCL
CK
/CK
tIS
CKE
Command
PALL
NOP
tRP
tMRD
tMRD
DLL enable
MRS
tMRD
PALL
tMRD
REF
REF
tRP
tRFC
DLL reset
MRS
tRFC
EMRS
tMRD
OCD default
200 cycles (min)
Power up and Initialization Sequence
Preliminary Data Sheet E0933E30 (Ver. 3.0)
34
Any
command
EMRS
t
400ns
EMRS
EMRS(3)
EMRS(2)
Follow OCD
Flowchart
tOIT
OCD calibration mode
exit
EDE5108AHBG, EDE5116AHBG
Programming the Mode Register and Extended Mode Registers
For application flexibility, burst length, burst type, /CAS latency, DLL reset function, write recovery time (tWR)
are user defined variables and must be programmed with a mode register set command [MRS]. Additionally, DLL
disable function, driver impedance, additive /CAS latency, ODT (On Die Termination), single-ended strobe, and OCD
(Off-Chip Driver Impedance Adjustment) are also user defined variables and must be programmed with an extended
mode register set command [EMRS]. Contents of the Mode Register (MR) or Extended Mode Registers (EMR (#))
can be altered by reexecuting the MRS and EMRS commands. If the user chooses to modify only a subset of the
MRS or EMRS variables, all variables must be redefined when the MRS or EMRS commands are issued.
MRS, EMRS and Reset DLL do not affect array contents, which means reinitialization including those can be
executed any time after power-up without affecting array contents.
L
EO
DDR2 SDRAM Mode Register Set [MRS]
The mode register stores the data for controlling the various operating modes of DDR2 SDRAM. It controls /CAS
latency, burst length, burst sequence, test mode, DLL reset, tWR and various vendor specific options to make DDR2
SDRAM useful for various applications. The default value of the mode register is not defined, therefore the mode
register must be written after power-up for proper operation. The mode register is written by asserting low on /CS,
/RAS, /CAS, /WE, BA0 and BA1, while controlling the state of address pins A0 to A13.
The DDR2 SDRAM should be in all bank precharge with CKE already high prior to writing into the mode register.
The mode register set command cycle time (tMRD) is required to complete the write operation to the mode register.
The mode register contents can be changed using the same command and clock cycle requirements during normal
operation as long as all banks are in the precharge state. The mode register is divided into various fields depending
on functionality. Burst length is defined by A0 to A2 with options of 4 and 8 bit burst lengths. The burst length
decodes are compatible with DDR SDRAM. Burst address sequence type is defined by A3, /CAS latency is defined
by A4 to A6. The DDR2 doesn’t support half clock latency mode. A7 is used for test mode. A8 is used for DLL reset.
A7 must be set to low for normal MRS operation. Write recovery time tWR is defined by A9 to A11. Refer to the
table for specific codes.
BA1 BA0 A13 A12 A11 A10 A9
A7
A6
A5
A4
MRS mode
Pr
Write recovery for autoprecharge
0*1
0
A8
DLL reset
0
No
1
Yes
0*1 PD
WR
DLL TM
/CAS latency
A3
A2
BT
A1
A0
Address field
Burst length
Mode register
Burst length
A7
Mode
A3
Burst type
0
Normal
0
Sequential
1
1
Test
A2
A1
A0
BL
0
1
0
4
0
1
1
8
Interleave
od
BA1 BA0
A8
/CAS latency
A11
A10
A9
WR
A6
A5
A4
Latency
1
0
EMRS(2)
0
0
0
Reserved
0
0
0
Reserved
1
1
EMRS(3): Reserved
0
0
1
0
0
1
Reserved
0
1
0
0
1
0
Reserved
0
1
1
3
5
1
0
0
4
6
1
0
1
2
3
Active power down exit timing
0
1
1
0
Fast exit (use tXARD timing)
1
0
0
1
Slow exit (use tXARDS timing)
1
0
1
1
1
0
Reserved
1
1
1
Reserved
4
5
uc
A12
DDR2 800
EMRS(1)
DDR2 667
MRS
1
DDR2 533
0
0
DDR2 400
0
1
1
0
Reserved
1
1
1
Reserved
Notes: 1. BA1 and A13 are reserved for future use and must be programmed to 0 when setting the mode register.
2. WR (min.) (Write Recovery for autoprecharge) is determined by tCK (max.) and WR (max.) is determined by tCK (min.).
WR in clock cycles is calculated by dividing tWR (in ns) by tCK (in ns) and rounding up to the next integer
(WR [cycles] = tWR (ns) / tCK (ns)).
The mode register must be programmed to this value. This is also used with tRP to determine tDAL.
Preliminary Data Sheet E0933E30 (Ver. 3.0)
35
t
Mode Register Set (MRS)
EDE5108AHBG, EDE5116AHBG
DDR2 SDRAM Extended Mode Registers Set [EMRS]
EMRS (1) Programming
The extended mode register (1) stores the data for enabling or disabling the DLL, output driver strength, additive
latency, ODT, /DQS disable, OCD program, RDQS enable. The default value of the extended mode register (1) is
not defined, therefore the extended mode register (1) must be written after power-up for proper operation. The
extended mode register (1) is written by asserting low on /CS, /RAS, /CAS, /WE, high on BA0 and low on BA1, while
controlling the states of address pins A0 to A13. The DDR2 SDRAM should be in all banks precharge with CKE
already high prior to writing into the extended mode register (1). The mode register set command cycle time (tMRD)
must be satisfied to complete the write operation to the extended mode register (1). Mode register contents can be
changed using the same command and clock cycle requirements during normal operation as long as all banks are in
the precharge state. A0 is used for DLL enable or disable. A1 is used for enabling a half strength output driver. A3
to A5 determines the additive latency, A7 to A9 are used for OCD control, A10 is used for /DQS disable and A11 is
used for RDQS enable. A2 and A6 are used for ODT setting.
EO
BA1 BA0 A13 A12 A11 A10 A9
0
0*1
1
BA1 BA0
0
0
A6
A5
A4
MRS
1
EMRS(1)
0
EMRS(2)
A3
A2
L
A6
A2
Rtt (nominal )
0
0
ODT Disabled
0
1
75Ω
1
0
150Ω
1
1
50Ω
EMRS(3): Reserved
A1
A0
Address field
Rtt Additive latency Rtt D.I.C DLL
MRS mode
1
1
A7
Qoff RDQS /DQS OCD program
0
1
A8
Extended mode register
A0
DLL enable
0
Enable
1
Disable
Driver impedance adjustment
A8
A7
0
0
0
OCD calibration mode exit
0
0
1
Drive(1)
0
1
0
Drive(0)
A5
A4
A3
Latency
1
0
0
Adjust mode* 2
0
0
0
0
1
1
1
OCD Calibration default* 3
0
0
1
1
0
1
0
2
0
1
1
3
1
0
0
4
1
0
1
Reserved
Additive latency
Qoff
0
Output buffers enabled
1
Output buffers disabled
/DQS enable
0
Enable
1
Disable
od
Pr
A12
A10
Operation
A9
1
1
0
Reserved
1
1
1
Reserved
Driver strength control
Output driver
A11
RDQS enable
0
Disable
1
Enable
A10
impedance control
size
0
Normal
100%
1
Weak
60%
Strobe function matrix
uc
A11
(RDQS enable)
Driver
A1
(/DQS enable) RDQS/DM
/RDQS
DQS
0 (Disable)
0 (Enable)
DM
High-Z
DQS
/DQS
0 (Disable)
1 (Disable)
DM
High-Z
DQS
High-Z
1 (Enable)
0 (Enable)
RDQS
/RDQS
DQS
/DQS
1 (Enable)
1 (Disable)
RDQS
High-Z
DQS
High-Z
EMRS (1)
Preliminary Data Sheet E0933E30 (Ver. 3.0)
36
t
Notes: 1. A13 is reserved for future use, and must be programmed to 0 when setting the extended mode register.
2 When adjust mode is issued, AL from previously set value must be applied.
3. After setting to default, OCD mode needs to be exited by setting A9 to A7 to 000.
Refer to the chapter Off-Chip Driver (OCD)Impedance Adjustment for detailed information.
/DQS
EDE5108AHBG, EDE5116AHBG
DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during power up initialization, and upon
returning to normal operation after having the DLL disabled. The DLL is automatically disabled when entering selfrefresh operation and is automatically re-enabled upon exit of self-refresh operation. Any time the DLL is enabled
(and subsequently reset), 200 clock cycles must occur before a read command can be issued to allow time for the
internal clock to be synchronized with the external clock. Failing to wait for synchronization to occur may result in a
violation of the tAC or tDQSCK parameters.
*1
EO
EMRS (2) Programming
The extended mode register (2) controls refresh related features. The default value of the extended mode
register (2) is not defined, therefore the extended mode register (2) must be written after power-up for proper
operation. The extended mode register (2) is written by asserting low on CS, /RAS, /CAS, /WE, high on BA1 and low
on BA0, while controlling the states of address pins A0 to A13. The DDR2 SDRAM should be in all bank precharge
with CKE already high prior to writing into the extended mode register (2). The mode register set command cycle
time (tMRD) must be satisfied to complete the write operation to the extended mode register (2). Mode register
contents can be changed using the same command and clock cycle requirements during normal operation as long
as all banks are in the precharge state.
BA1 BA0
1
A13
A12
A11
0
A10
A9
A8
0*1
A7
A6
A5
A4
A2
A1
A0
Address field
Extended mode register (2)
0*1
SRF
L
A7
A3
High Temperature
Self-refresh rate
Enable
0
Disable
1
Enable
Pr
Note: 1 The rest bits in EMRS (2) is reserved for future use and all bits in EMRS (2) except A7, BA0 and BA1
must be programmed to 0 when setting the extended mode register (2) during initialization.
EMRS(2)
EMRS (3) Programming: Reserved*1
BA1 BA0
A12
A11
A10
1
A9
A8
0*1
A7
A6
A5
A4
A3
A2
A1
A0
Address Field
od
1
A13
Extended Mode Register(3)
Note : 1. EMRS (3) is reserved for future use and all bits except BA0 and BA1 must be programmed
to 0 when setting the mode register during initialization.
EMRS (3)
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
37
EDE5108AHBG, EDE5116AHBG
Off-Chip Driver (OCD) Impedance Adjustment
DDR2 SDRAM supports driver calibration feature and the OCD Flow Chart is an example of sequence. Every
calibration mode command should be followed by “OCD calibration mode exit” before any other command being
issued. MRS should be set before entering OCD impedance adjustment and ODT (On Die Termination) should be
carefully controlled depending on system environment.
MRS should be set before entering OCD impedance adjustment and ODT should
be carefully controlled depending on system environment
Start
EMRS: OCD calibration mode exit
EMRS: Drive(0)
DQ & DQS high ; /DQS low
DQ & DQS low ; /DQS high
EO
EMRS: Drive(1)
ALL OK
ALL OK
Test
Test
Need calibration
Need calibration
EMRS: OCD calibration mode exit
EMRS: OCD calibration mode exit
L
EMRS :
EMRS :
Enter Adjust Mode
Enter Adjust Mode
Pr
BL=4 code input to all DQs
BL=4 code input to all DQs
Inc, Dec, or NOP
Inc, Dec, or NOP
od
EMRS: OCD calibration mode exit
EMRS: OCD calibration mode exit
EMRS: OCD calibration mode exit
OCD Flow Chart
t
uc
End
Preliminary Data Sheet E0933E30 (Ver. 3.0)
38
EDE5108AHBG, EDE5116AHBG
Extended Mode Register Set for OCD Impedance Adjustment
OCD impedance adjustment can be done using the following EMRS mode. In drive mode all outputs are driven out
by DDR2 SDRAM and drive of RDQS is dependent on EMRS bit enabling RDQS operation. In Drive (1) mode, all
DQ, DQS (and RDQS) signals are driven high and all /DQS signals are driven low. In drive (0) mode, all DQ, DQS
(and RDQS) signals are driven low and all /DQS signals are driven high.
In adjust mode, BL = 4 of operation code data must be used. In case of OCD calibration default, output driver
characteristics follow approximate nominal V/I curve for 18Ω output drivers, but are not guaranteed. If tighter control
is required, which is controlled within 18Ω ± 3Ω driver impedance range, OCD must be used.
[OCD Mode Set Program]
A8
A7
Operation
0
0
0
OCD calibration mode exit
0
0
1
Drive (1) DQ, DQS, (RDQS) high and /DQS low
0
1
0
Drive (0) DQ, DQS, (RDQS) low and /DQS high
1
0
0
Adjust mode
1
1
1
OCD calibration default
EO
A9
L
OCD Impedance Adjustment
To adjust output driver impedance, controllers must issue the ADJUST EMRS command along with a 4bit burst code
to DDR2 SDRAM as in OCD Adjustment Program table. For this operation, burst length has to be set to BL = 4 via
MRS command before activating OCD and controllers must drive this burst code to all DQs at the same time. DT0 in
OCD Adjustment Program table means all DQ bits at bit time 0, DT1 at bit time 1, and so forth. The driver output
impedance is adjusted for all DDR2 SDRAM DQs simultaneously and after OCD calibration, all DQs of a given
DDR2 SDRAM will be adjusted to the same driver strength setting. The maximum step count for adjustment is 16
and when the limit is reached, further increment or decrement code has no effect. The default setting may be any
step within the 16-step range.
[OCD Adjustment Program]
Operation
Pr
4bits burst data inputs to all DQs
DT1
DT2
DT3
Pull-up driver strength
Pull-down driver strength
0
0
0
0
NOP
NOP
0
0
0
1
Increase by 1 step
NOP
0
0
1
0
Decrease by 1 step
NOP
0
1
0
0
NOP
Increase by 1 step
1
0
0
0
0
1
0
1
0
1
1
0
1
0
0
1
1
0
1
0
Other combinations
od
DT0
NOP
Decrease by 1 step
Increase by 1 step
Increase by 1 step
Decrease by 1 step
Increase by 1 step
Increase by 1 step
Decrease by 1 step
Decrease by 1 step
Decrease by 1 step
Reserved
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
39
EDE5108AHBG, EDE5116AHBG
For proper operation of adjust mode, WL = RL − 1 = AL + CL − 1 clocks and tDS/tDH should be met as the Output
Impedance Control Register Set Cycle. For input data pattern for adjustment, DT0 to DT3 is a fixed order and not
affected by MRS addressing mode (i.e. sequential or interleave).
/CK
CK
Command
EMRS
NOP
EMRS
WL
NOP
tWR
DQS, /DQS
tDS tDH
DQ_in
DT0
DT1
DT2
DT3
EO
OCD adjust mode
OCD calibration mode exit
Output Impedance Control Register Set Cycle
Drive Mode
Drive mode, both drive (1) and drive (0), is used for controllers to measure DDR2 SDRAM Driver impedance before
OCD impedance adjustment. In this mode, all outputs are driven out tOIT after “Enter drive mode” command and all
output drivers are turned-off tOIT after “OCD calibration mode exit” command as the ”Output Impedance
Measurement/Verify Cycle”.
CK
Command
L
/CK
NOP
EMRS
Pr
High-Z
DQS, /DQS
EMRS
High-Z
DQs high and /DQS low for drive (1), DQs low and /DQS high for drive (0)
DQs high for drive (1)
DQ
DQs low for drive (0)
Enter drivemode
od
tOIT
tOIT
OCD Calibration mode exit
Output Impedance Measurement/Verify Cycle
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
40
EDE5108AHBG, EDE5116AHBG
ODT (On Die Termination)
On Die Termination (ODT), is a feature that allows a DRAM to turn on/off termination resistance for each DQ, DQS,
/DQS, RDQS, /RDQS, and DM signal via the ODT control pin. The ODT feature is designed to improve signal
integrity of the memory channel by allowing the DRAM controller to independently turn on/off termination resistance
for any or all DRAM devices.
The ODT function is turned off and not supported in self-refresh mode.
VDDQ
VDDQ
VDDQ
sw3
sw2
sw1
Rval3
Rval2
Rval1
EO
DRAM
input
buffer
Input
Pin
Rval1
sw1
Rval2
Rval3
sw2
sw3
VSSQ
VSSQ
VSSQ
L
Switch sw1, sw2 or sw3 is enabled by ODT pin.
Selection between sw1, sw2 or sw3 is determined by Rtt (nominal) in EMRS
Termination included on all DQs, DM, DQS, /DQS, RDQS and /RDQS pins.
Target Rtt (Ω) = (Rval1) / 2, (Rval2) / 2 or (Rval3) / 2
Pr
Functional Representation of ODT
/CK
CK
Command
EMRS
od
tAOFD
ODT
NOP
tIS
tMOD (max.)
tMOD (min.)
Rtt
Old setting
Updating
New Setting
uc
Note: tAOFD must be met before issuing EMRS command. ODT must remain low for the entire duration of tMOD window.
ODT update Delay Timing
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
41
EDE5108AHBG, EDE5116AHBG
/CK
T0
T1
T2
T3
T4
T5
T6
CK
CKE
tAXPD ≤ 6tCK
tIS
tIS
ODT
tAOFD
tAOND
Internal
Term Res.
EO
/CK
Rtt
tAON min.
tAOF min.
tAON max.
tAOF max.
ODT Timing for Active and Standby Mode
T0
T1
T2
T3
T4
T5
T6
CK
CKE
L
tAXPD ≤ 6tCK
tIS
tIS
ODT
tAOFPD max.
tAOFPD min.
Pr
Internal
Term Res.
tAONPD min.
Rtt
tAONPD max.
ODT Timing for Power-Down Mode
t
uc
od
Preliminary Data Sheet E0933E30 (Ver. 3.0)
42
EDE5108AHBG, EDE5116AHBG
T-5
T-4
T-3
T-2
T-1
T0
T1
T2
T3
T4
/CK
CK
tANPD
tIS
CKE
Entering slow exit active power down mode
or precharge power down mode.
tIS
ODT
Active and standby
mode timings to
be applied.
tAOFD
EO
Internal
Term Res.
Rtt
tIS
ODT
Power down
mode timings to
be applied.
tAOFPD(max.)
Internal
Term Res.
Rtt
L
tIS
ODT
tAOND
Active and standby
mode timings to
be applied.
Rtt
Pr
Internal
Term Res.
tIS
ODT
Power down
mode timings to
be applied.
tAONPD(max.)
od
Internal
Term Res.
Rtt
ODT Timing Mode Switch at Entering Power-Down Mode
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
43
EDE5108AHBG, EDE5116AHBG
T0
T1
T4
T5
T6
T7
T8
T9
T10
T11
/CK
CK
tIS
tAXPD
CKE
Exiting from slow active power down mode
or precharge power down mode.
tIS
EO
Active and standby
mode timings to
be applied.
ODT
tAOFD
Internal
Term Res.
Rtt
tIS
ODT
Power down
mode timings to
be applied.
tAOFPD (max.)
L
Internal
Term Res.
Active and standby
mode timings to
be applied.
Rtt
tIS
ODT
tAOND
Pr
Internal
Term Res.
Rtt
tIS
ODT
tAONPD(max.)
Internal
Term Res.
od
Power down
mode timings to
be applied.
Rtt
ODT Timing Mode Switch at Exiting Power-Down Mode
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
44
EDE5108AHBG, EDE5116AHBG
Bank Activate Command [ACT]
The bank activate command is issued by holding /CAS and /WE high with /CS and /RAS low at the rising edge of the
clock. The bank addresses BA0 and BA1, are used to select the desired bank. The row address A0 through A13 is
used to determine which row to activate in the selected bank. The Bank activate command must be applied before
any read or write operation can be executed. Immediately after the bank active command, the DDR2 SDRAM can
accept a read or write command on the following clock cycle. If a R/W command is issued to a bank that has not
satisfied the tRCD (min.) specification, then additive latency must be programmed into the device to delay when the
R/W command is internally issued to the device. The additive latency value must be chosen to assure tRCD (min.)
is satisfied. Additive latencies of 0, 1, 2, 3 and 4 are supported. Once a bank has been activated it must be
precharged before another bank activate command can be applied to the same bank. The bank active and
precharge times are defined as tRAS and tRP, respectively. The minimum time interval between successive bank
activate commands to the same bank is determined by the /RAS cycle time of the device (tRC), which is equal to
tRAS + tRP. The minimum time interval between successive bank activate commands to the different bank is
determined by (tRRD).
EO
/CK
T0
T1
T2
T3
Tn
Tn+1
Tn+2
Tn+3
PRE
ACT
CK
Command
Address
ACT
ROW: 0
Posted
READ
ACT
Posted
READ
PRE
tRCD(min.)
COL: 0
ROW: 1
COL: 1
ROW: 0
L
tCCD
Additive latency (AL)
Bank0 Read begins
tRRD
tRAS
tRP
Bank0
Active
Pr
tRC
Bank1
Active
Bank0
Precharge
Bank1
Precharge
Bank0
Active
Bank Activate Command Cycle (tRCD = 3, AL = 2, tRP = 3, tRRD = 2, tCCD = 2)
t
uc
od
Preliminary Data Sheet E0933E30 (Ver. 3.0)
45
EDE5108AHBG, EDE5116AHBG
Read and Write Access Modes
EO
After a bank has been activated, a read or write cycle can be executed. This is accomplished by setting /RAS high,
/CS and /CAS low at the clock’s rising edge. /WE must also be defined at this time to determine whether the access
cycle is a read operation (/WE high) or a write operation (/WE low).
The DDR2 SDRAM provides a fast column access operation. A single read or write command will initiate a serial
read or write operation on successive clock cycles. The boundary of the burst cycle is strictly restricted to specific
segments of the page length. For example, the 32M bits × 4 I/O × 4 banks chip has a page length of 2048 bits
(defined by CA0 to CA9, CA11). The page length of 2048 is divided into 512 uniquely addressable boundary
segments (4 bits each). A 4 bits burst operation will occur entirely within one of the 512 groups beginning with the
column address supplied to the device during the read or write command (CA0 to CA9, CA11). The second, third
and fourth access will also occur within this group segment, however, the burst order is a function of the starting
address, and the burst sequence.
A new burst access must not interrupt the previous 4-bit burst operation. The minimum /CAS to /CAS delay is
defined by tCCD, and is a minimum of 2 clocks for read or write cycles.
-1
/CK
CK
Command
L
Posted /CAS
Posted /CAS operation is supported to make command and data bus efficient for sustainable bandwidths in DDR2
SDRAM. In this operation, the DDR2 SDRAM allows a /CAS read or write command to be issued immediately after
the /RAS bank activate command (or any time during the /RAS-/CAS-delay time, tRCD, period). The command is
held for the time of the Additive Latency (AL) before it is issued inside the device. The Read Latency (RL) is
controlled by the sum of AL and the /CAS latency (CL). Therefore if a user chooses to issue a R/W command before
the tRCD (min), then AL (greater than 0) must be written into the EMRS. The Write Latency (WL) is always defined
as RL − 1 (read latency −1) where read latency is defined as the sum of additive latency plus /CAS latency (RL = AL
+ CL).
0
1
2
ACT
READ
3
4
NOP
5
6
7
8
9
11
12
11
12
NOP
WRIT
WL = RL – 1 = 4
Pr
AL = 2
DQS, /DQS
10
CL = 3
≥ tRCD
RL = AL + CL = 5
DQ
out0 out1 out2 out3
in0 in1 in2 in3
≥ tRAC
od
Read Followed by a Write to the Same Bank
[AL = 2 and CL = 3, RL = (AL + CL) = 5, WL = (RL - 1) = 4]
-1
0
1
2
3
/CK
CK
ACT
NOP
AL = 0
READ
5
NOP
CL = 3
DQS, /DQS
≥ tRCD
RL = AL + CL = 3
DQ
6
7
WRIT
8
46
NOP
in0 in1 in2 in3
t
Read Followed by a Write to the Same Bank
[AL = 0 and CL = 3, RL = (AL + CL) = 3, WL = (RL - 1) = 2]
Preliminary Data Sheet E0933E30 (Ver. 3.0)
10
WL = RL – 1 = 2
out0 out1 out2 out3
≥ tRAC
9
uc
Command
4
EDE5108AHBG, EDE5116AHBG
Burst Mode Operation
Burst mode operation is used to provide a constant flow of data to memory locations (write cycle), or from memory
locations (read cycle). The parameters that define how the burst mode will operate are burst sequence and burst
length. DDR2 SDRAM supports 4 bits burst and 8bits burst modes only. For 8 bits burst mode, full interleave
address ordering is supported, however, sequential address ordering is nibble based for ease of implementation.
The burst type, either sequential or interleaved, is programmable and defined by the address bit 3 (A3) of the MRS,
which is similar to the DDR-I SDRAM operation. Seamless burst read or write operations are supported.
Unlike DDR-I devices, interruption of a burst read or writes operation is limited to ready by Read or Write by Write at
the boundary of Burst 4. Therefore the burst stop command is not supported on DDR2 SDRAM devices.
[Burst Length and Sequence]
Burst length
Interleave addressing (decimal)
000
0, 1, 2, 3
0, 1, 2, 3
001
1, 2, 3, 0
1, 0, 3, 2
010
2, 3, 0, 1
2, 3, 0, 1
011
3, 0, 1, 2
3, 2, 1, 0
000
0, 1, 2, 3, 4, 5, 6, 7
0, 1, 2, 3, 4, 5, 6, 7
001
1, 2, 3, 0, 5, 6, 7, 4
1, 0, 3, 2, 5, 4, 7, 6
010
2, 3, 0, 1, 6, 7, 4, 5
2, 3, 0, 1, 6, 7, 4, 5
011
3, 0, 1, 2, 7, 4, 5, 6
3, 2, 1, 0, 7, 6, 5, 4
100
4, 5, 6, 7, 0, 1, 2, 3
4, 5, 6, 7, 0, 1, 2, 3
101
5, 6, 7, 4, 1, 2, 3, 0
5, 4, 7, 6, 1, 0, 3, 2
110
6, 7, 4, 5, 2, 3, 0, 1
6, 7, 4, 5, 2, 3, 0, 1
111
7, 4, 5, 6, 3, 0, 1, 2
7, 6, 5, 4, 3, 2, 1, 0
EO
Starting address (A2, A1, A0) Sequential addressing (decimal)
4
8
L
t
uc
od
Pr
Note: Page length is a function of I/O organization and column addressing
16M bits × 8 organization (CA0 to CA9); Page Length = 1024 bits
8M bits × 16 organization (CA0 to CA9); Page Length = 1024 bits
Preliminary Data Sheet E0933E30 (Ver. 3.0)
47
EDE5108AHBG, EDE5116AHBG
Burst Read Command [READ]
The Burst Read command is initiated by having /CS and /CAS low while holding /RAS and /WE high at the rising
edge of the clock. The address inputs determine the starting column address for the burst. The delay from the start
of the command to when the data from the first cell appears on the outputs is equal to the value of the read latency
(RL). The data strobe output (DQS) is driven low 1 clock cycle before valid data (DQ) is driven onto the data bus.
The first bit of the burst is synchronized with the rising edge of the data strobe (DQS). Each subsequent data-out
appears on the DQ pin in phase with the DQS signal in a source synchronous manner.
The RL is equal to an additive latency (AL) plus /CAS latency (CL). The CL is defined by the mode register set
(MRS), similar to the existing SDR and DDR-I SDRAMs. The AL is defined by the extended mode register set
(EMRS).
T0
T1
T2
T3
T4
T5
T6
T7
T8
T7
T8
/CK
CK
EO
Command
READ
NOP
≤ tDQSCK
DQS, /DQS
CL = 3
RL = 3
DQ
out0 out1 out2 out3
L
Burst Read Operation (RL = 3, BL = 4 (AL = 0 and CL = 3))
T0
CK
Command
READ
T1
T2
T3
T4
T5
T6
Pr
/CK
NOP
≤ tDQSCK
CL = 3
RL = 3
DQ
od
DQS, /DQS
out0 out1 out2 out3 out4 out5 out6 out7
Burst Read Operation (RL = 3, BL = 8 (AL = 0 and CL = 3))
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
48
EDE5108AHBG, EDE5116AHBG
T0
T1
T2
T3
T4
T5
T6
T7
T8
/CK
CK
Command
Posted
READ
NOP
≤ tDQSCK
DQS, /DQS
AL = 2
CL = 3
RL = 5
out0 out1 out2 out3
DQ
EO
Burst Read Operation (RL = 5, BL = 4 (AL = 2, CL = 3))
T0
T1
T3
T4
T5
T6
T7
T8
T9
/CK
CK
Command
Posted
READ
NOP
Posted
WRIT
NOP
NOP
tRTW (Read to Write = 4 clocks)
L
DQS, /DQS
RL = 5
WL = RL - 1 = 4
out0 out1 out2 out3
DQ
in0
in2
in1
in3
Pr
Burst Read Followed by Burst Write (RL = 5, WL = RL-1 = 4, BL = 4)
The minimum time from the burst read command to the burst write command is defined by a read-to-write-turnaround-time, which is 4 clocks.
T0
T1
T2
T3
CK
Command
Posted
READ
NOP
A
Posted
READ
AL = 2
T5
T6
T7
T8
NOP
B
DQS, /DQS
T4
od
/CK
uc
CL = 3
RL = 5
out
A0
DQ
out
A1
out
A2
out
A3
out
B0
out
B1
out
B2
Seamless Burst Read Operation (RL = 5, AL = 2, and CL = 3)
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
49
EDE5108AHBG, EDE5116AHBG
Enabling a read command at every other clock supports the seamless burst read operation. This operation is
allowed regardless of same or different banks as long as the banks are activated.
T0
T1
T2
READ
NOP
READ
T3
T4
T5
T6
T7
T8
T9
T10
T11
CK
/CK
Command
A
NOP
B
DQS, /DQS
RL = 4
out
A0
EO
DQ
out
A1
out
A2
out
A3
out
B0
out out
B1 B2
out
B3
out
B4
out
B5
out
B6
out
B7
Burst interrupt is only
allowed at this timing.
Burst Read Interrupt by Read
L
Notes: 1. Read burst interrupt function is only allowed on burst of 8. burst interrupt of 4 is prohibited.
2. Read burst of 8 can only be interrupted by another read command. Read burst interruption by write
command or precharge command is prohibited.
3. Read burst interrupt must occur exactly two clocks after previous read command. any other read burst
interrupt timings are prohibited.
4. Read burst interruption is allowed to any bank inside DRAM.
5. Read burst with auto precharge enabled is not allowed to interrupt.
6. Read burst interruption is allowed by another read with auto precharge command.
7. All command timings are referenced to burst length set in the mode register. They are not referenced to
actual burst. For example, minimum read to precharge timing is AL + BL/2 where BL is the burst length
set in the mode register and not the actual burst (which is shorter because of interrupt).
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
50
EDE5108AHBG, EDE5116AHBG
Burst Write Command [WRIT]
The Burst Write command is initiated by having /CS, /CAS and /WE low while holding /RAS high at the rising edge of
the clock. The address inputs determine the starting column address. Write latency (WL) is defined by a read
latency (RL) minus one and is equal to (AL + CL −1). A data strobe signal (DQS) should be driven low (preamble)
one clock prior to the WL. The first data bit of the burst cycle must be applied to the DQ pins at the first rising edge
of the DQS following the preamble. The tDQSS specification must be satisfied for write cycles. The subsequent
burst bit data are issued on successive edges of the DQS until the burst length of 4 is completed. When the burst
has finished, any additional data supplied to the DQ pins will be ignored. The DQ Signal is ignored after the burst
write operation is complete. The time from the completion of the burst write to bank precharge is the write recovery
time (tWR).
T0
T1
T2
T3
T4
T5
T6
T7
T9
/CK
CK
EO
Command
WRIT
NOP
PRE
NOP
ACT
≤ tDQSS
DQS, /DQS
≥tWR
WL = RL –1 = 2
in0
DQ
in1
in2
≥tRP
in3
L
Completion of
the burst write
Burst Write Operation (RL = 3, WL = 2, BL = 4 tWR = 2 (AL=0, CL=3))
Pr
T0
T1
T2
/CK
CK
Command
WRIT
T3
T4
T6
T7
T8
PRE
NOP
DQS, /DQS
od
≤ tDQSS
≥tWR
WL = RL –1 = 2
DQ
T5
in0
in1
in2
in3
in4
in5
in6
T9
NOP
T11
ACT
≥tRP
in7
uc
Completion of
the burst write
Burst Write Operation (RL = 3, WL = 2, BL = 8 (AL=0, CL=3))
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
51
EDE5108AHBG, EDE5116AHBG
T0
T1
T2
T3
T4
T5
T6
T7
T9
/CK
CK
Posted
WRIT
Command
PRE
NOP
≤ tDQSS
DQS, /DQS
≥tWR
WL = RL −1 = 4
in0
DQ
in1
in2
in3
EO
Completion of
the burst write
Burst Write Operation (RL = 5, WL = 4, BL = 4 tWR = 3 (AL=2, CL=3))
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
/CK
CK
DQS, /DQS
Posted
READ
NOP
L
Command
Write to Read = CL - 1 + BL/2 + tWTR (2) = 6
NOP
CL = 3
AL = 2
WL = RL –1 = 4
RL = 5
>tWTR
=
Pr
in0
DQ
in1
in2
in3
out0
out1
Burst Write Followed by Burst Read (RL = 5, BL = 4, WL = 4, tWTR = 2 (AL=2, CL=3))
The minimum number of clock from the burst write command to the burst read command is CL - 1 + BL/2 + a write
to-read-turn-around-time (tWTR). This tWTR is not a write recovery time (tWR) but the time required to transfer the
4bit write data from the input buffer into sense amplifiers in the array.
T1
T2
CK
Command
Posted
WRIT
A
NOP
Posted
WRIT
B
od
T0
/CK
T3
T4
T5
T6
T7
T8
NOP
WL = RL − 1 = 4
in
A0
DQ
in
A1
in
A2
uc
DQS, /DQS
in
A3
in
B0
in
B1
in
B2
in
B3
Seamless Burst Write Operation (RL = 5, WL = 4, BL = 4)
t
Enabling a write command every other clock supports the seamless burst write operation. This operation is allowed
regardless of same or different banks as long as the banks are activated.
Preliminary Data Sheet E0933E30 (Ver. 3.0)
52
EDE5108AHBG, EDE5116AHBG
T0
T1
T2
WRIT
NOP
WRIT
T3
T4
T5
T6
T7
T8
T9
T10
T11
CK
/CK
Command
A
NOP
B
DQS, /DQS
WL = 3
in in in in
A0 A1 A2 A3
DQ
in
B0
in in in in in in
B1 B2 B3 B4 B5 B6
in
B7
EO
Burst interrupt is only
allowed at this timing.
Write Interrupt by Write (WL = 3, BL = 8)
L
Notes :1. Write burst interrupt function is only allowed on burst of 8. Burst interrupt of 4 is prohibited.
2. Write burst of 8 can only be interrupted by another write command. Write burst interruption by read
command or precharge command is prohibited.
3. Write burst interrupt must occur exactly two clocks after previous write command. Any other write burst
interrupt timings are prohibited.
4. Write burst interruption is allowed to any bank inside DRAM.
5. Write burst with auto precharge enabled is not allowed to interrupt.
6. Write burst interruption is allowed by another write with auto precharge command.
7. All command timings are referenced to burst length set in the mode register. They are not referenced to
actual burst. For example, minimum write to precharge timing is WL+BL/2+tWR where tWR starts with
the rising clock after the un-interrupted burst end and not from the end of actual burst end.
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
53
EDE5108AHBG, EDE5116AHBG
Write Data Mask
One write data mask (DM) pin for each 8 data bits (DQ) will be supported on DDR2 SDRAMs, Consistent with the
implementation on DDR-I SDRAMs. It has identical timings on write operations as the data bits, and though used in
a uni-directional manner, is internally loaded identically to data bits to insure matched system timing. DM is not used
during read cycles.
T1
T2
T3
T4
in
in
T5
Tn
DQS
/DQS
DQ
in
in
in
in
in
in
in
EO
DM
Write mask latency = 0
Data Mask Timing
[tDQSS(min.)]
L
/CK
CK
Command
tWR
WRIT
NOP
WL
tDQSS
DQS, /DQS
DM
Pr
DQ
in0
in2 in3
WL
[tDQSS(max.)]
DQ
DM
od
DQS, /DQS
tDQSS
in0
in2 in3
Data Mask Function, WL = 3, AL = 0 shown
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
54
EDE5108AHBG, EDE5116AHBG
Precharge Command [PRE]
The precharge command is used to precharge or close a bank that has been activated. The precharge command is
triggered when /CS, /RAS and /WE are low and /CAS is high at the rising edge of the clock. The precharge
command can be used to precharge each bank independently or all banks simultaneously. Three address bits A10,
BA0 and BA1 are used to define which bank to precharge when the command is issued.
[Bank Selection for Precharge by Address Bits]
BA0
BA1
Precharged Bank(s)
L
L
L
Bank 0 only
L
H
L
Bank 1 only
L
L
H
Bank 2 only
L
H
H
Bank 3 only
H
×
×
All banks 0 to 3
EO
A10
Remark: H: VIH, L: VIL, ×: VIH or VIL
Burst Read Operation Followed by Precharge
Minimum read to precharge command spacing to the same bank = AL + BL/2 clocks
For the earliest possible precharge, the precharge command may be issued on the rising edge that is
“Additive latency (AL) + BL/2 clocks” after a Read command. A new bank active (command) may be issued to the
same bank after the RAS precharge time (tRP). A precharge command cannot be issued until tRAS is satisfied.
T0
T1
T2
T3
T4
T5
T6
T7
T8
L
/CK
CK
Command
Posted
READ
NOP
PRE
ACT
NOP
NOP
AL + BL/2 clocks
Pr
DQS, /DQS
AL = 1
≥tRP
CL = 3
RL = 4
out0
DQ
out1
out2
out3
≥tRAS
Burst Read Operation Followed by Precharge (RL = 4, BL = 4 (AL=1, CL=3))
T1
T2
T3
CK
Command
Posted
READ
od
T0
/CK
NOP
T4
T5
T6
NOP
PRE
AL + /BL2 clocks
ACT
T8
NOP
uc
DQS, /DQS
AL = 2
T7
≥ tRP
CL = 3
RL = 5
DQ
out0
≥ tRAS(min.)
out1
out2
out3
Preliminary Data Sheet E0933E30 (Ver. 3.0)
55
t
Burst Read Operation Followed by Precharge (RL = 5, BL = 4 (AL=2, CL=3))
EDE5108AHBG, EDE5116AHBG
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
/CK
CK
Command
Posted
READ
NOP
NOP
PRE
NOP
ACT
AL + BL/2 Clocks
DQS, /DQS
≥ tRP
CL = 4
AL = 2
RL = 6
out0
DQ
out1
out2
out3
out4
out5
out6
out7
≥ tRAS(min.)
Burst Read Operation Followed by Precharge (RL = 6 (AL=2, CL=4, BL=8))
L
EO
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
56
EDE5108AHBG, EDE5116AHBG
Burst Write followed by Precharge
Minimum Write to Precharge Command spacing to the same bank = WL + BL/2 clocks + tWR
For write cycles, a delay must be satisfied from the completion of the last burst write cycle until the precharge
command can be issued. This delay is known as a write recovery time (tWR) referenced from the completion of the
burst write to the precharge command. No precharge command should be issued prior to the tWR delay, as DDR2
SDRAM allows the burst interrupt operation only Read by Read or Write by Write at the boundary of burst 4.
T0
T1
T2
T3
T4
T5
T6
T7
T8
/CK
CK
Command
Posted
WRIT
NOP
PRE
EO
≥ tWR
DQS, /DQS
WL = 3
in0
DQ
in2
in3
Completion of
the burst write
Burst Write Followed by Precharge (WL = (RL-1) =3)
L
T0
in1
T1
T2
T3
T4
T5
T6
T7
T9
/CK
CK
DQS, /DQS
Posted
WRIT
Pr
Command
PRE
NOP
≥ tWR
WL = 4
od
in0
DQ
in1
in2
in3
Completion of
the burst write
Burst Write Followed by Precharge (WL = (RL-1) = 4)
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
57
EDE5108AHBG, EDE5116AHBG
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T11
/CK
CK
Command
Posted
WRIT
NOP
PRE
≥ tWR
DQS, /DQS
WL = 4
in0
DQ
in1
in2
in3
in4
in5
in6
in7
Burst Write Followed by Precharge (WL = (RL-1) = 4,BL= 8)
L
EO
Completion of
the burst write
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
58
EDE5108AHBG, EDE5116AHBG
Auto Precharge Operation
EO
Before a new row in an active bank can be opened, the active bank must be precharged using either the precharge
command or the auto precharge function. When a read or a write command is given to the DDR2 SDRAM, the /CAS
timing accepts one extra address, column address A10, to allow the active bank to automatically begin precharge at
the earliest possible moment during the burst read or write cycle. If A10 is low when the read or write Command is
issued, then normal read or write burst operation is executed and the bank remains active at the completion of the
burst sequence. If A10 is high when the Read or Write Command is issued, then the auto precharge function is
engaged. During auto precharge, a read Command will execute as normal with the exception that the active bank
will begin to precharge on the rising edge which is /CAS latency (CL) clock cycles before the end of the read burst.
Auto precharge can also be implemented during Write commands. The precharge operation engaged by the Auto
precharge command will not begin until the last data of the burst write sequence is properly stored in the memory
array.
This feature allows the precharge operation to be partially or completely hidden during burst read cycles (dependent
upon /CAS latency) thus improving system performance for random data access. The /RAS lockout circuit internally
delays the Precharge operation until the array restore operation has been completed so that the auto precharge
command may be issued with any read or write command.
L
Burst Read with Auto Precharge [READA]
If A10 is high when a Read Command is issued, the Read with Auto Precharge function is engaged. The DDR2
SDRAM starts an auto Precharge operation on the rising edge which is (AL + BL/2) cycles later from the read with
AP command when tRAS (min) is satisfied. If tRAS (min.) is not satisfied at the edge, the start point of auto
precharge operation will be delayed until tRAS (min.) is satisfied. A new bank active (command) may be issued to
the same bank if the following two conditions are satisfied simultaneously.
(1) The /RAS precharge time (tRP) has been satisfied from the clock at which the auto precharge begins.
(2) The /RAS cycle time (tRC) from the previous bank activation has been satisfied.
T0
T1
T2
T3
T4
T5
T6
T7
Tn
/CK
CK
Posted
READ
Pr
Command
A10 = 1
NOP
ACT
NOP
ACT
AL + BL/2
DQS, /DQS
AL = 2
≥ tRP
CL = 3
RL = 5
od
out0 out1 out2 out3
DQ
tRC (min.)
Auto precharge begins
Burst Read with Auto Precharge Followed by an Activation to the Same Bank (tRC limit)
(RL = 5, BL = 4 (AL = 2, CL = 3, tRTP ≤ 2tCK))
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
59
EDE5108AHBG, EDE5116AHBG
T-1
T0
T1
T2
T3
T4
T5
T6
T7
Tn
/CK
CK
A10 = 1
Posted
READ
Command
NOP
ACT
≥ tRAS(min.)
DQS, /DQS
≥ tRP
CL = 3
AL = 2
RL = 5
out0
DQ
out2
out1
out3
tRC (min.)
EO
Auto precharge begins
Burst Read with Auto Precharge Followed by an Activation to the Same Bank (tRAS lockout case)
(RL = 5, BL = 4 (AL = 2, CL = 3))
T0
T1
T2
T3
T4
T5
T6
T7
T8
/CK
CK
A10 = 1
L
Command
Posted
READ
ACT
NOP
NOP
≥ tRAS(min.)
DQS, /DQS
tRP (min.)
AL = 2
CL = 3
Pr
RL = 5
DQ
out0
out1
out2
out3
≥tRC
Auto precharge begins
T0
T1
T2
od
Burst Read with Auto Precharge Followed by an Activation to the Same Bank (tRP limit)
(RL = 5, BL = 4 (AL = 2, CL = 3, tRTP ≤ 2tCK))
T3
T4
CK
/CK
A10 = 1
Command
T5
T6
T7
T8
NOP
READ
DQS, /DQS
AL = 2
CL = 3
T10
T11
ACT
uc
≥tRAS (min.)
T9
≥tRP
RL = 5
out0 out1 out2 out3 out4 out5 out6 out7
DQ
≥tRC
Preliminary Data Sheet E0933E30 (Ver. 3.0)
60
t
Auto precharge begins
Burst Read with Auto Precharge Followed by an Activation to the Same Bank
(RL = 5, BL = 8 (AL = 2, CL = 3, tRTP ≤ 2tCK))
EDE5108AHBG, EDE5116AHBG
Burst Write with Auto Precharge [WRITA]
If A10 is high when a write command is issued, the Write with auto precharge function is engaged. The DDR2
SDRAM automatically begins precharge operation after the completion of the burst writes plus write recovery time
(tWR). The bank undergoing auto precharge from the completion of the write burst may be reactivated if the
following two conditions are satisfied.
(1) The data-in to bank activate delay time (tWR + tRP) has been satisfied.
(2) The /RAS cycle time (tRC) from the previous bank activation has been satisfied.
T0
T1
T2
T3
T4
T5
T6
T7
Tm
/CK
CK
A10 = 1
Posted
WRIT
NOP
EO
Command
ACT
DQS, /DQS
≥tWR
WL = RL –1 = 2
in0
DQ
in1
in2
≥ tRP
in3
tRC (min.)
L
Completion of the burst write
Auto precharge begins
Burst Write with Auto Precharge (tRC Limit) (WL = 2, tWR =2)
T0
T3
CK
Command
DQS, /DQS
A10 = 1
Posted
WRIT
NOP
T4
T5
T6
T7
T8
T9
T10
T11
Pr
/CK
NOP
in0
od
tWR (min.)
WL = RL –1 = 4
DQ
ACT
in1
in2
tRP (min.)
in3
≥ tRC
Completion of the burst write
Auto precharge begins
Burst Write with Auto Precharge (tWR + tRP) (WL = 4, tWR =2, tRP=3)
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
61
EDE5108AHBG, EDE5116AHBG
T0
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
CK
/CK
A10 = 1
Command
NOP
WRIT
ACT
DQS, /DQS
WL = RL − 1 = 4
≥tWR
in0
DQ
in1
in2
in3
in4
in5
in6
≥tRP
in7
≥tRC
EO
Auto precharge begins
Burst Write with Auto Precharge Followed by an Activation to the Same Bank
(WL = 4, BL = 8, tWR = 2, tRP = 3)
L
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
62
EDE5108AHBG, EDE5116AHBG
Refresh Requirements
DDR2 SDRAM requires a refresh of all rows in any rolling 64ms interval. Each refresh is generated in one of two
ways: by an explicit automatic refresh command, or by an internally timed event in self-refresh mode. Dividing the
number of device rows into the rolling 64 ms interval defines the average refresh interval, tREFI, which is a guideline
to controllers for distributed refresh timing.
Automatic Refresh Command [REF]
EO
When /CS, /RAS and /CAS are held low and /WE high at the rising edge of the clock, the chip enters the automatic
refresh mode (REF). All banks of the DDR2 SDRAM must be precharged and idle for a minimum of the precharge
time (tRP) before the auto-refresh command (REF) can be applied. An address counter, internal to the device,
supplies the bank address during the refresh cycle. No control of the external address bus is required once this
cycle has started.
When the refresh cycle has completed, all banks of the DDR2 SDRAM will be in the precharged (idle) state. A delay
between the auto-refresh command (REF) and the next activate command or subsequent auto-refresh command
must be greater than or equal to the auto-refresh cycle time (tRFC).
To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh
interval is provided. A maximum of 8 refresh commands can be posted to any given DDR2 SDRAM, meaning that
the maximum absolute interval between any refresh command and the next Refresh command is 9 × tREFI.
T0
T1
T2
T3
/CK
CK
VIH
≥ tRP
L
CKE
Command
PRE
NOP
≥ tRFC
≥ tRFC
REF
NOP
REF
Any
Command
Automatic Refresh Command
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
63
EDE5108AHBG, EDE5116AHBG
Self Refresh Command [SELF]
The DDR2 SDRAM device has a built-in timer to accommodate self-refresh operation. The self-refresh command is
defined by having /CS, /RAS, /CAS and CKE held low with /WE high at the rising edge of the clock.
ODT must be turned off before issuing self-refresh command, by either driving ODT pin low or using EMRS
command. Once the command is registered, CKE must be held low to keep the device in self-refresh mode.
When the DDR2 SDRAM has entered self-refresh mode all of the external signals except CKE, are “don’t care”.
The clock is internally disabled during self-refresh operation to save power. The user may change the external clock
frequency or halt the external clock one clock after Self-Refresh entry is registered, however, the clock must be
restarted and stable before the device can exit self-refresh operation. Once self-refresh exit command is registered,
a delay equal or longer than the tXSNR or tXSRD must be satisfied before a valid command can be issued to the
device. CKE must remain high for the entire self-refresh exit period tXSRD for proper operation. NOP or deselect
commands must be registered on each positive clock edge during the self-refresh exit interval. ODT should also be
turned off during tXSRD.
EO
T0
T1
T2
T3
T4
T5
T6
Tm
Tn
tCK
tCH tCL
/CK
CK
≥ tXSNR
tRP*
≥ tXSRD
CKE
L
ODT
tIS
tIS
tAOFD
Pr
tIS
tIS tIH
Comand
SELF
NOP
NOP
NOP
Valid
od
Notes: 1. Device must be in the “All banks idle” state prior to entering self refresh mode.
2. ODT must be turned off tAOFD before entering self refresh mode, and can be turned on again
when tXSRD timing is satisfied.
3. tXSRD is applied for a read or a read with autoprecharge command.
4. tXSNR is applied for any command except a read or a read with autoprecharge command.
Self Refresh Command
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
64
EDE5108AHBG, EDE5116AHBG
Power-Down [PDEN]
EO
Power-down is synchronously entered when CKE is registered low (along with NOP or deselect command). CKE is
not allowed to go low while mode register or extended mode register command time, or read or write operation is in
progress. CKE is allowed to go low while any of other operations such as row activation, precharge or auto
precharge, or auto-refresh is in progress, but power-down IDD spec will not be applied until finishing those
operations. Timing diagrams are shown in the following pages with details for entry into power-down.
The DLL should be in a locked state when power-down is entered. Otherwise DLL should be reset after exiting
power-down mode for proper read operation.
If power-down occurs when all banks are idle, this mode is referred to as precharge power-down; if power-down
occurs when there is a row active in any bank, this mode is referred to as active power-down. Entering power-down
deactivates the input and output buffers, excluding CK, /CK, ODT and CKE. Also the DLL is disabled upon entering
precharge power-down or slow exit active power-down, but the DLL is kept enabled during fast exit active powerdown. In power-down mode, CKE low and a stable clock signal must be maintained at the inputs of the DDR2
SDRAM, and ODT should be in a valid state but all other input signals are “Don’t Care”. CKE low must be
maintained until tCKE has been satisfied. Power-down duration is limited by 9 times tREFI of the device.
The power-down state is synchronously exited when CKE is registered high (along with a NOP or deselect
command). CKE high must be maintained until tCKE has been satisfied. A valid, executable command can be
applied with power-down exit latency, tXP, tXARD, or tXARDS, after CKE goes high. Power-down exit latency is
defined at AC Characteristics table of this data sheet.
CK
/CK
tIS tIH
tIS tIH
tIH
tIS
tIH
tIS tIH
CKE
L
VALID
Command
NOP
NOP
tCKE min
VALID
VALID
VALID
tXP, tXARD,
tXARDS
Pr
tCKE min
Enter power-down mode
VIH or VIL
Exit power-down mode
Power Down
Read to Power-Down Entry
T0
T1
T2
Command
Tx
Tx+1
Tx+2
CKE
DQS
/DQS
AL + CL
DQ
Tx+5
Tx+6
Tx+7
Tx+8
Tx+9
T2
Tx
out
0
Tx+1
out
1
out
2
Tx+2
out
3
Tx+3
READ
Tx+4
Tx+5
BL=4
uc
Command
T1
Tx+4
Read operation starts with a read command and
CKE should be kept high until the end of burst operation.
READ
VIH
T0
Tx+3
od
/CK
CK
Tx+6
Tx+7
Tx+8
Tx+9
CKE should be kept high until the end of burst operation.
VIH
CKE
DQS
/DQS
out
0
out out
1
2
out
3
out
4
Preliminary Data Sheet E0933E30 (Ver. 3.0)
65
out out
5
6
out
7
t
AL + CL
DQ
BL=8
EDE5108AHBG, EDE5116AHBG
Read with Auto Precharge to Power-Down Entry
T0
T1
T2
Tx
Tx+1
Tx+2
Tx+3
Tx+4
Tx+5
Tx+6
Tx+7
Tx+8
Tx+9
/CK
CK
Command
READA
PRE
AL + BL/2
with tRTP = 7.5ns
and tRAS min. satisfied
BL=4
CKE
CKE should be kept high
until the end of burst operation.
DQS
/DQS
AL + CL
DQ
EO
T0
Command
T1
T2
Tx
out
0
out
1
Tx+1
out
2
Tx+2
out
3
Tx+3
Tx+4
Tx+5
Tx+6
Tx+7
Tx+8
Tx+9
Start internal precharge
READA
BL=8
AL + BL/2
with tRTP = 7.5ns
and tRAS min. satisfied
PRE
CKE should be kept high
until the end of burst operation.
CKE
DQS
/DQS
AL + CL
L
DQ
out
0
out
1
out
2
out
3
out
4
out out
5
6
out
7
Write to Power-Down Entry
T1
/CK
CK
Command
WRIT
CKE
Tm
Tm+1 Tm+2
Tm+3 Tx
Tx+1
Pr
T0
Tx+2
Tx+3
Tx+4
Tx+5
Tx+6
tWTR
DQS
WL
in
0
DQ
T0
Command
T1
Tm
in
1
Tm+1
in
2
in
3
od
/DQS
Tm+2 Tm+3
WRIT
Tm+4 Tm+5
Tx+1
Tx+2
Tx+3
Tx+4
uc
CKE
Tx
BL=4
tWTR
DQS
/DQS
WL
DQ
in
0
in
1
in
2
in
3
in
4
in
5
in
6
in
7
BL=8
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
66
EDE5108AHBG, EDE5116AHBG
Write with Auto Precharge to Power-Down Entry
T0
T1
Tm
Tm+1
Tm+2
Tm+3
Tx
Tx+1
Tx+2
Tx+3
Tx+4
Tx+5
Tx+6
/CK
CK
Command
WRITA
PRE
CKE
WR*1
DQS
/DQS
WL
in
0
DQ
EO
T0
T1
Tm
in
1
Tm+1
in
2
BL=4
in
3
Tm+2
Tm+3
Tm+4
Tm+5
Tx
Tx+1
Tx+2
Tx+3
Tx+4
/CK
CK
Command
WRITA
PRE
CKE
DQS
/DQS
WL
L
DQ
WR*1
in
0
in
1
in
2
in
3
in
4
in
5
in
6
BL=8
in
7
Note: 1. WR is programmed through MRS
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
67
EDE5108AHBG, EDE5116AHBG
Refresh command to Power-Down Entry
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
/CK
CK
Command
REF
CKE can go to low one clock after an auto-refresh command
CKE
Active command to power-down entry
EO
Command
ACT
CKE can go to low one clock after an active command
CKE
L
Precharge/Precharge all command to power-down entry
PRE or
PALL
Pr
Command
CKE can go to low one clock after a precharge or precharge all command
CKE
Command
MRS or
EMRS
uc
od
MRS/EMRS command to power-down entry
CKE
tMRD
t
Preliminary Data Sheet E0933E30 (Ver. 3.0)
68
EDE5108AHBG, EDE5116AHBG
Asynchronous CKE Low Event
DRAM requires CKE to be maintained high for all valid operations as defined in this data sheet. If CKE
asynchronously drops low during any valid operation DRAM is not guaranteed to preserve the contents of array. If
this event occurs, memory controller must satisfy DRAM timing specification tDELAY before turning off the clocks.
Stable clocks must exist at the input of DRAM before CKE is raised high again. DRAM must be fully re-initialized
(steps 4 through 13) as described in initialization sequence. DRAM is ready for normal operation after the
initialization sequence. See AC Characteristics table for tDELAY specification
Stable clocks
tCK
/CK
CK
EO
CKE
tDELAY
CKE asynchronously
drops low
Clocks can be
turned off after
this point
L
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
69
EDE5108AHBG, EDE5116AHBG
Input Clock Frequency Change during Precharge Power Down
DDR2 SDRAM input clock frequency can be changed under following condition:
DDR2 SDRAM is in precharged power-down mode. ODT must be turned off and CKE must be at logic low level.
A minimum of 2 clocks must be waited after CKE goes low before clock frequency may change. SDRAM input clock
frequency is allowed to change only within minimum and maximum operating frequency specified for the particular
speed grade. During input clock frequency change, ODT and CKE must be held at stable low levels.
Once input clock frequency is changed, stable new clocks must be provided to DRAM before precharge power-down
may be exited and DLL must be RESET via EMRS after precharge power-down exit. Depending on new clock
frequency an additional MRS command may need to be issued to appropriately set the WR, CL and soon. During
DLL relock period, ODT must remain off. After the DLL lock time, the DRAM is ready to operate with new clock
frequency.
Clock Frequency Change in Precharge Power Down Mode
EO
T0
T1
T2
NOP
NOP
T4
Tx
Tx+1
Ty
Ty+1
Ty+2 Ty+3
Ty+4
Tz
/CK
CK
Command
NOP
CKE
DLL
RESET
Frequency change
occurs here
NOP
Valid
200 clocks
L
ODT
NOP
tRP
tXP
tAOFD
ODT is off during
DLL RESET
Minmum 2 clocks
required before
changing frequency
Stable new clock
before power down exit
Pr
Burst Interruption
Interruption of a burst read or write cycle is prohibited.
od
No Operation Command [NOP]
The no operation command should be used in cases when the DDR2 SDRAM is in an idle or a wait state. The
purpose of the no operation command is to prevent the DDR2 SDRAM from registering any unwanted commands
between operations. A no operation command is registered when /CS is low with /RAS, /CAS, and /WE held high at
the rising edge of the clock. A no operation command will not terminate a previous operation that is still executing,
such as a burst read or write cycle.
Deselect Command [DESL]
The deselect command performs the same function as a no operation command. Deselect Command occurs when
/CS is brought high at the rising edge of the clock, the /RAS, /CAS, and /WE signals become don’t cares.
t
uc
Preliminary Data Sheet E0933E30 (Ver. 3.0)
70
EDE5108AHBG, EDE5116AHBG
Package Drawing
60-ball FBGA
Solder ball: Lead free (Sn-Ag-Cu)
Unit: mm
10.0 ± 0.1
0.2 S B
INDEX MARK
10.5 ± 0.1
EO
L
0.2 S A
0.2 S
1.20 max.
S
Pr
0.35 ± 0.05
0.1 S
60-φ0.45 ± 0.05
B
φ0.15 M S A B
0.8
od
8.0
A
INDEX MARK
uc
1.6
6.4
0.8
t
ECA-TS2-0181-01
Preliminary Data Sheet E0933E30 (Ver. 3.0)
71
EDE5108AHBG, EDE5116AHBG
84-ball FBGA
Solder ball: Lead free (Sn-Ag-Cu)
Unit: mm
10.0 ± 0.1
0.2 S B
EO
12.5 ± 0.1
INDEX MARK
L
0.2 S A
0.2 S
1.20 max.
S
Pr
0.1 S
0.35 ± 0.05
B
84-φ0.45 ± 0.05
φ0.15 M S A B
0.8
od
11.2
A
1.6 0.8
t
6.4
uc
INDEX MARK
ECA-TS2-0182-01
Preliminary Data Sheet E0933E30 (Ver. 3.0)
72
EDE5108AHBG, EDE5116AHBG
Recommended Soldering Conditions
Please consult with our sales offices for soldering conditions of the EDE51XXAHBG.
Type of Surface Mount Device
EDE5108AHBG: 60-ball FBGA < Lead free (Sn-Ag-Cu) >
EDE5116AHBG: 84-ball FBGA < Lead free (Sn-Ag-Cu) >
L
EO
t
uc
od
Pr
Preliminary Data Sheet E0933E30 (Ver. 3.0)
73
EDE5108AHBG, EDE5116AHBG
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
EO
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
L
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Pr
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
t
uc
od
Preliminary Data Sheet E0933E30 (Ver. 3.0)
74
EDE5108AHBG, EDE5116AHBG
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
EO
[Product applications]
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
L
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
This product is not designed to be resistant to electromagnetic waves or radiation. This product must be
used in a non-condensing environment.
Pr
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E0107
t
uc
od
Preliminary Data Sheet E0933E30 (Ver. 3.0)
75
Similar pages