Ecliptek EB51F2B15N-20.000M Specification control drawing Datasheet

Marketing Bulletin
DATE:
May 10, 2004
TO:
Affected Customers
FROM:
Mark Stoner
RE:
Product Termination
To all concerned parties,
This bulletin is to notify all customers of the termination of the following Ecliptek series
effective May 10th, 2004:
Series
EB51F2
ES51F2
EB52F2
ES52F2
Description
5V 14 Pin DIP TCXO, HCMOS
5V 14 Pin DIP TCXO, Sinewave
3.3V 14 Pin DIP TCXO, HCMOS
3.3V 14 Pin DIP TCXO, Sinewave
Recommended Replacement
None
None
None
None
Because of the circumstances surrounding this termination, there will be no end-of-life
policy exercised. The series will be terminated with no purchasing or lifetime buy
window available. We will however have a recommended alternative product for these
series within the next ninety (90) days.
All of us at Ecliptek Corporation apologize for any inconvenience this may have caused
and can assure you we are taking measures to insure this will not happen again in the
future. If there are any questions pertaining to this bulletin, please feel free to contact
me. Thank you for your cooperation.
Best Regards,
Mark W. Stoner
Director of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234
STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
Initial Frequency Tolerance
vs. Operating Temperature Range
vs. Input Voltage Change
vs. Load Change
vs. Aging
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VDD )
Input Current (Steady State @25°C)
1.544MHz to 44.736MHz
±1ppm (at Nominal Vdd and Vc)
See Table 1 for Maximum Values
±0.3ppm Maximum (VDD ±5%)
±0.2ppm Maximum (±10%)
±1ppm/year Maximum (@25°C)
See Table 1 for Operating Temperature Range
-55°C to +125°C
5.0Vdc ±5%
15mA Maximum < 20.000MHz
30mA Maximum > 20.000MHz
VDD-0.5Vdc Minimum
0.5Vdc Maximum
6nSec (20% to 80% of waveform)
50% ±5% (@ 50% of waveform)
30pF HCMOS Load
-60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset,
-140dBc/Hz at 100kHz Offset,
±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=2.5Vdc; Vdd=5.0Vdc)
0.0VDC to VDD
2.5VDC ±2.0VDC / Positive Transfer Characteristic
±10% Maximum
10kOhms Typical
OBSOLETE
Output Voltage Logic High
Output Voltage Logic Low
Rise/Fall Time
Duty Cycle
Load Drive Capabillity
Phase Noise (Typical)
Frequency Deviation
Control VoltageRange(VCR )
Control Voltage /TransferFunction
Linearity
Input Impedance
ENVIRONMENTAL & MECHANICAL
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
TABLE 1: PART NUMBERING CODES
FREQUENCY STABILITY
X Denotes availability from 1.544MHz to 32.768MHz
Y Denotes availability for any valid frequency
Range
Code
50
30
20
15
Code
±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range
0°C to +50°C
Y
Y
Y
Y
A
0°C to +70°C
Y
Y
Y
X
B
Y
Y
X
X
-20°C to +70°C
C
Y
Y
X
-30°C to +75°C
D
Y
X
-40°C to +85°C
E
OPERATING
TEMPERATURE
PART NUMBERING GUIDE
EB51F2 A 10 V - 20.000M
Frequency
Voltage Control Option
V = Voltage Control on Pin 1
N = No Connect on Pin 1
Frequency Stability Code Per Table 1
Operating Temperature
Range Code Per Table 1
MARKING GUIDE
(Line #1) ECLIPTEK
(Line #2) XX.XXXM
1
15.240
±0.203
7
0.6 MAX
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
NOTE: Pin 1 shall be marked with a dot. Marking shall
conform to conditions listed in TQC41-001-000.
8
20.3 ±0.5
5.08
MIN
13.0
±0.5
(Line #3) XX Y ZZ
∅0.457
±0.100 (X4)
7.620
±0.203
14
ECLIPTEK
XX.XXXM
XXYZZ
Frequency
SPECIFICATION CONTROL DRAWING
8.3
MAX
Drawing Number
CSC26-140-001
Title
ALL DIMENSIONS
IN MILLIMETERS
PIN
CONNECTION
1
No Connect or Voltage Control
7
Ground/Case Ground
8
Output
14
Supply Voltage
5.0V Full Size (VC)TCXO
Revision
Effectivity Date
A
09-09-03
ECN Number
8159
Approved By
PAGE 1 OF 2
Date Released By
Date
STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
Initial Frequency Tolerance
vs. Operating Temperature Range
vs. Input Voltage Change
vs. Load Change
vs. Aging
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VDD )
Input Current (Steady State @25°C)
Output Voltage
Load Drive Capabillity
Phase Noise (Typical)
9.600MHz to 44.736MHz
OBSOLETE
±1ppm (at Nominal Vdd and Vc)
See Table 1 for Maximum Values
±0.3ppm Maximum (VDD ±5%)
±0.2ppm Maximum (±10%)
±1ppm/year Maximum (@25°C)
See Table 1 for Operating Temperature Range
-55°C to +125°C
5.0Vdc ±5%
10mA Maximum
1.0Vp-p Minimum Clipped Sinewave
10kOhms//10pF
-60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset,
-140dBc/Hz at 100kHz Offset
±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=2.5Vdc; Vdd=5.0Vdc)
0.0VDC to VDD
2.5VDC ±2.0VDC / Positive Transfer Characteristic
±10% Maximum
10kOhms Typical
Frequency Deviation
Control VoltageRange(VCR )
Control Voltage /TransferFunction
Linearity
Input Impedance
ENVIRONMENTAL & MECHANICAL
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
TABLE 1: PART NUMBERING CODES
FREQUENCY STABILITY
X Denotes availability from 9.600MHz to 32.768MHz
Y Denotes availability for any valid frequency
Range
Code
50
30
20
15
Code
±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range
0°C to +50°C
Y
Y
Y
Y
A
0°C to +70°C
Y
Y
Y
X
B
-20°C to +70°C
Y
Y
X
C
Y
Y
D
-30°C to +75°C
Y
X
-40°C to +85°C
E
OPERATING
TEMPERATURE
PART NUMBERING GUIDE
ES51F2 A 10 V - 20.000M
Frequency
Voltage Control Option
V = Voltage Control on Pin 1
N = No Connect on Pin 1
Frequency Stability Code Per Table 1
Operating Temperature
Range Code Per Table 1
MARKING GUIDE
(Line #1) ECLIPTEK
(Line #2) XX.XXXM
ECLIPTEK
XX.XXXM
XXYZZ
Frequency
(Line #3) XX Y ZZ
1
15.240
±0.203
7
NOTE: Pin 1 shall be marked with a dot. Marking shall
conform to conditions listed in TQC41-001-000.
∅0.457
±0.100 (X4)
7.620
±0.203
14
8
20.3 ±0.5
5.08
MIN
13.0
±0.5
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
0.6 MAX
SPECIFICATION CONTROL DRAWING
8.3
MAX
Drawing Number
CSC26-160-001
Title
ALL DIMENSIONS
IN MILLIMETERS
PIN
CONNECTION
1
No Connect or Voltage Control
7
Ground/Case Ground
8
Output
14
Supply Voltage
5.0V Clipped Sinewave Full Size (VC)TCXO
Revision
Effectivity Date
A
09-09-03
ECN Number
8163
Approved By
PAGE 1 OF 2
Date Released By
Date
STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
Initial Frequency Tolerance
vs. Operating Temperature Range
vs. Input Voltage Change
vs. Load Change
vs. Aging
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VDD )
Input Current (Steady State @25°C)
1.544MHz to 44.736MHz
OBSOLETE
±1ppm (at Nominal Vdd and Vc)
See Table 1 for Maximum Values
±0.3ppm Maximum (VDD ±5%)
±0.2ppm Maximum (±10%)
±1ppm/year Maximum (@25°C)
See Table 1 for Operating Temperature Range
-55°C to +125°C
3.3Vdc ±5%
15mA Maximum < 20.000MHz
25mA Maximum > 20.000MHz
90% of Vdd Minimum
10% of Vdd Maximum
6nSec (20% to 80% of waveform)
50% ±5% (@ 50% of waveform)
15pF HCMOS Load
-60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset,
-140dBc/Hz at 100kHz Offset,
±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=1.65Vdc; Vdd=3.3Vdc)
0.0VDC to VDD
1.65VDC ±1.35VDC / Positive Transfer Characteristic
±10% Maximum
10kOhms Typical
Output Voltage Logic High
Output Voltage Logic Low
Rise/Fall Time
Duty Cycle
Load Drive Capabillity
Phase Noise (Typical)
Frequency Deviation
Control VoltageRange(VCR )
Control Voltage /TransferFunction
Linearity
Input Impedance
ENVIRONMENTAL & MECHANICAL
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
TABLE 1: PART NUMBERING CODES
FREQUENCY STABILITY
X Denotes availability from 1.544MHz to 32.768MHz
Y Denotes availability for any valid frequency
Range
Code
50
30
20
15
Code
±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range
0°C to +50°C
Y
Y
Y
Y
A
0°C to +70°C
Y
Y
Y
X
B
Y
Y
X
-20°C to +70°C
C
Y
Y
-30°C to +75°C
D
Y
X
-40°C to +85°C
E
OPERATING
TEMPERATURE
PART NUMBERING GUIDE
EB52F2 A 10 V - 20.000M
Frequency
Voltage Control Option
V = Voltage Control on Pin 1
N = No Connect on Pin 1
Frequency Stability Code Per Table 1
Operating Temperature
Range Code Per Table 1
MARKING GUIDE
(Line #1) ECLIPTEK
(Line #2) XX.XXXM
1
15.240
±0.203
7
0.6 MAX
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
NOTE: Pin 1 shall be marked with a dot. Marking shall
conform to conditions listed in TQC41-001-000.
8
20.3 ±0.5
5.08
MIN
13.0
±0.5
(Line #3) XX Y ZZ
∅0.457
±0.100 (X4)
7.620
±0.203
14
ECLIPTEK
XX.XXXM
XXYZZ
Frequency
SPECIFICATION CONTROL DRAWING
8.3
MAX
Drawing Number
CSC26-150-001
Title
ALL DIMENSIONS
IN MILLIMETERS
PIN
CONNECTION
1
No Connect or Voltage Control
7
Ground/Case Ground
8
Output
14
Supply Voltage
3.3V FULL SIZE (VC)TCXO
Revision
Effectivity Date
A
09-09-03
ECN Number
8161
Approved By
PAGE 1 OF 2
Date Released By
Date
STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
Initial Frequency Tolerance
vs. Operating Temperature Range
vs. Input Voltage Change
vs. Load Change
vs. Aging
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VDD )
Input Current (Steady State @25°C)
Output Voltage
Load Drive Capabillity
Phase Noise (Typical)
9.600MHz to 44.736MHz
OBSOLETE
±1ppm (at Nominal Vdd and Vc)
See Table 1 for Maximum Values
±0.3ppm Maximum (VDD ±5%)
±0.2ppm Maximum (±10%)
±1ppm/year Maximum (@25°C)
See Table 1 for Operating Temperature Range
-55°C to +125°C
3.3Vdc ±5%
10mA Maximum
0.7Vp-p Minimum Clipped Sinewave
10kOhms//10pF
-60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset,
-140dBc/Hz at 100kHz Offset
±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=1.65Vdc; Vdd=3.3Vdc)
0.0VDC to VDD
1.65VDC ±1.35VDC / Positive Transfer Characteristic
±10% Maximum
10kOhms Typical
Frequency Deviation
Control VoltageRange(VCR )
Control Voltage /TransferFunction
Linearity
Input Impedance
ENVIRONMENTAL & MECHANICAL
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
TABLE 1: PART NUMBERING CODES
FREQUENCY STABILITY
X Denotes availability from 9.600MHz to 32.768MHz
Y Denotes availability for any valid frequency
Range
Code
50
30
20
15
Code
±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range
0°C to +50°C
Y
Y
Y
Y
A
0°C to +70°C
Y
Y
Y
X
B
-20°C to +70°C
Y
Y
X
C
Y
Y
D
-30°C to +75°C
Y
X
-40°C to +85°C
E
OPERATING
TEMPERATURE
PART NUMBERING GUIDE
ES52F2 A 10 V - 20.000M
Frequency
Voltage Control Option
V = Voltage Control on Pin 1
N = No Connect on Pin 1
Frequency Stability Code Per Table 1
Operating Temperature
Range Code Per Table 1
MARKING GUIDE
(Line #1) ECLIPTEK
(Line #2) XX.XXXM
ECLIPTEK
XX.XXXM
XXYZZ
Frequency
(Line #3) XX Y ZZ
1
15.240
±0.203
7
NOTE: Pin 1 shall be marked with a dot. Marking shall
conform to conditions listed in TQC41-001-000.
∅0.457
±0.100 (X4)
7.620
±0.203
14
8
20.3 ±0.5
5.08
MIN
13.0
±0.5
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
0.6 MAX
SPECIFICATION CONTROL DRAWING
8.3
MAX
Drawing Number
CSC26-170-001
Title
ALL DIMENSIONS
IN MILLIMETERS
PIN
CONNECTION
1
No Connect or Voltage Control
7
Ground/Case Ground
8
Output
14
Supply Voltage
3.3V Clipped Sinewave Full Size (VC)TCXO
Revision
Effectivity Date
A
09-09-03
ECN Number
8165
Approved By
PAGE 1 OF 2
Date Released By
Date
Similar pages