FDC10(W) SERIES 10 WATTS DC-DC CONVERTER FEATURES • 10 WATTS OUTPUT POWER • OUTPUT CURRENT UP TO 2.5A • STANDARD 2.0 X 1.0 X 0.4 INCH PACKAGE • HIGH EFFICIENCY UP TO 87% • 2:1 AND 4:1 WIDE INPUT VOLTAGE RANGE • SIX-SIDED CONTINUOUS SHIELD • FIXED SWITCHING FREQUENCY (300kHz) • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH OPTIONS NEGATIVE & POSITIVE LOGIC REMOTE ON/OFF APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Measurement Equipment Semiconductor Equipment DESCRIPTION The FDC10 and FDC10-W series offer 10 watts of output power from a 2.0 x 1.0 x 0.4 inch package. FDC10 series have 2:1 wide input voltage of 9 ~ 18, 18 ~ 36 and 36 ~ 75VDC. FDC10-W series have 4:1 ultra wide input voltage of 9 ~ 36 and 18 ~ 75VDC. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted. INPUT SPECIFICATIONS OUTPUT SPECIFICATIONS Output power Voltage accuracy Single / Dual Minimum load Line regulation ± 1% Single / Dual ± 0.2% Single ± 0.5% Load regulation No Load to Full Load Dual ± 1% Cross regulation(Dual) Asymmetrical load 25% / 100% FL ± 5% Single Ripple and noise 20MHz bandwidth See table Dual ±0.02% / ºC, max. Temperature coefficient Transient response recovery time 25% load step change 3.3VDC output Over voltage protection 5VDC output Zener diode clamp 12VDC output 15VDC output Over load protection % of FL at nominal input Short circuit protection Efficiency Isolation resistance Input to Output Input(Output) to Case 500VDC Safety approvals Case material Dimensions Weight MIL-HDBK-217F 9 ~ 18VDC 18 ~ 36VDC 36 ~ 75VDC 9 ~ 36VDC 18 ~ 75VDC Pi type 36VDC 100ms, max. 50VDC 100ms, max. 100VDC 100ms, max. 30mAp-p Input reflected ripple current Nominal input and Start up time Power up 20ms Constant resistive load Remote ON/OFF (Option) (Note 6) (Positive logic) DC-DC ON Open or 3.5V < Vr < 12V DC-DC OFF Short or 0V < Vr < 1.2V (Negative logic) DC-DC ON Short or 0V < Vr < 1.2V DC-DC OFF Open or 3.5V < Vr < 12V Input current of remote control pin Nominal input -0.5mA ~ +1mA Remote off state input current Nominal input 20mA ENVIRONMENTAL SPECIFICATIONS Operating ambient See table temperature (Reference derating curve) 1600VDC, min. 1minute 1600VDC, min. 1minute Maximum case temperature 9 10 ohms, min. Storage temperature range Non-conductive black plastic Potting material Page 1 of 3 12VDC input 24VDC input 48VDC input Input surge voltage 300kHz±10% Thermal shock IEC60950-1, UL60950-1, & EN60950-1 Vibration Nickel-coated copper Relative humidity Base material MTBF (Note 1) Input filter 300pF, max. Thermal impedance (Note 8) Isolation capacitance Switching frequency 250µs 3.9VDC 6.2VDC 15VDC 18VDC 150%, max. Continuous, automatics recovery GENERAL SPECIFICATIONS Isolation voltage Input voltage range 0% LL to HL at Full Load 12VDC nominal input 24VDC nominal input 48VDC nominal input FDC10-W 24VDC nominal input 48VDC nominal input FDC10 10 Watts, max. Standard -25ºC ~ +85ºC (with derating) M1 (Note 7) -40ºC ~ +85ºC (non-derating) M2 (W series) -40ºC ~ +85ºC (with derating) +105ºC -55ºC ~ +125ºC Nature convection 12ºC/watt Nature convection with heat-sink 10ºC/watt MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC CHARACTERISTICS Epoxy (UL94 V-0) EMI (Note 9) 2.00 X 1.00 X 0.40 Inch (50.8 X 25.4 X 10.2 mm) ESD 27g (0.95oz) Radiated immunity 3.342 x 106 hrs Fast transient (Note 10) Surge (Note 10) Conducted immunity www.pduke.com EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Class B ± 8kV Air Contact ± 6kV 10 V/m ± 2kV ± 1kV 10 Vr.m.s Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A 2014/4/30 FDC10(W) SERIES 10 WATTS Model Number Input Range Output Voltage FDC10-12S33 FDC10-12S05 FDC10-12S12 FDC10-12S15 FDC10-12D05 FDC10-12D12 FDC10-12D15 FDC10-24S33 (W) FDC10-24S05 (W) FDC10-24S12 (W) FDC10-24S15 (W) FDC10-24D05 (W) FDC10-24D12 (W) FDC10-24D15 (W) FDC10-48S33 (W) FDC10-48S05 (W) FDC10-48S12 (W) FDC10-48S15 (W) FDC10-48D05 (W) FDC10-48D12 (W) FDC10-48D15 (W) 9 ~ 18 VDC 9 ~ 18 VDC 9 ~ 18 VDC 9 ~ 18 VDC 9 ~ 18 VDC 9 ~ 18 VDC 9 ~ 18 VDC 18 ~ 36 (9 ~ 36) VDC 18 ~ 36 (9 ~ 36) VDC 18 ~ 36 (9 ~ 36) VDC 18 ~ 36 (9 ~ 36) VDC 18 ~ 36 (9 ~ 36) VDC 18 ~ 36 (9 ~ 36) VDC 18 ~ 36 (9 ~ 36) VDC 36 ~ 75 (18 ~ 75) VDC 36 ~ 75 (18 ~ 75) VDC 36 ~ 75 (18 ~ 75) VDC 36 ~ 75 (18 ~ 75) VDC 36 ~ 75 (18 ~ 75) VDC 36 ~ 75 (18 ~ 75) VDC 36 ~ 75 (18 ~ 75) VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC DC-DC CONVERTER (2) (3) Output Current Output No load Min. load Full load Ripple & Noise Input Current 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 2000mA 2000mA 830mA 670mA ± 1000mA ± 416mA ± 333mA 2000(2500mA) 2000mA 830mA 670mA ± 1000mA ± 416mA ± 333mA 2000(2500mA) 2000mA 830mA 670mA ± 1000mA ± 416mA ± 333mA 50mVp-p 50mVp-p 50mVp-p 50mVp-p 75mVp-p 75mVp-p 75mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 75mVp-p 75mVp-p 75mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 75mVp-p 75mVp-p 75mVp-p 17mA 21mA 38mA 36mA 39mA 47mA 45mA 15(13mA) 22(11mA) 18(16mA) 36(26mA) 28(15mA) 24(15mA) 31(22mA) 11(10mA) 14(9mA) 14(9mA) 10(11mA) 16(12mA) 19(20mA) 16(20mA) (4) (5) Eff (%) Capacitor Load max 80 81 84 84 84 83 84 80(78) 82 (80) 84 (84) 84 (81) 83 (82) 85 (80) 84 (80) 80(76) 84 (81) 86 (84) 87 (84) 84 (82) 86 (78) 85 (81) 6800µF 4700µF 690µF 470µF ± 680µF ± 330µF ± 110µF 6800µF 4700µF 690µF 470µF ± 680µF ± 330µF ± 110µF 6800µF 4700µF 690µF 470µF ± 680µF ± 330µF ± 110µF Note 1. 2. 3. 4. 5. 6. MIL-HDBK-217F @Ta=25 ºC, Full load. Typical value at nominal input and full load. (20MHz BW.) Typical value at nominal input voltage and no load. Typical value at nominal input voltage and full load. Test by minimum input and constant resistive load. The ON/OFF control pin voltage is referenced to -INPUT To order positive logic ON/OFF control add the suffix-P (Ex: FDC10-12S05-P); To order negative logic ON-OFF control add the suffix-N (Ex: FDC10-12S05-N) 7. M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than standard and M2 version. 8. Heat-sink is optional and P/N: 7G-0020C-F. 9. The FDC10 series standard module meets EN55022 Class A and Class B with external components. For more detail information, please contact with P-DUKE. 10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220 F/100V. μ CAUTION: This power module is not internally fused. An input line fuse must always be used. Page 2 of 3 www.pduke.com 2014/4/30 FDC10(W) SERIES 10 WATTS MECHANICAL DRAWING DC-DC CONVERTER ： PIN CONNECTION PIN SINGLE DUAL 1 + INPUT + INPUT 2 - INPUT - INPUT 3 + OUTPUT + OUTPUT 4 NO PIN COMMON 5 - OUTPUT - OUTPUT 6 CTRL(Option) CTRL(Option) 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) Page 3 of 3 www.pduke.com 2014/4/30