TC7SZ14F/FU TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7SZ14F,TC7SZ14FU Schmitt Inverter Features TC7SZ14F • High output drive: ±24 mA (min) at VCC = 3 V • Super high speed operation: tpd = 3.7 ns (typ.) • Operation voltage range: VCC (opr) = 1.65~5.5 V • 5.5-V tolerant inputs • 5.5-V power down protection output • Matches the performance of TC74LCX series when operated at 3.3- V VCC at VCC = 5 V, 50 pF TC7SZ14FU Weight: SSOP5-P-0.95 : 0.016 g (typ.) SSOP5-P-0.65A : 0.006 g (typ.) Marking Absolute Maximum Ratings (Ta = 25°C) Type name Characteristics Symbol Rating Unit Supply voltage range VCC −0.5 to 6 V DC input voltage VIN −0.5 to 6 V DC output voltage VOUT −0.5 to 6 V Input diode current IIK −20 mA Output diode current IOK −20 mA DC output current IOUT ±50 mA DC VCC/ground current ICC ±50 mA Power dissipation PD 200 mW Storage temperature Tstg −65 to 150 °C TL 260 °C Lead temperature (10 s) Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). 1 J A Pin Assignment (top view) NC 1 5 VCC IN A 2 GND 3 4 OUT Y 2007-11-01 TC7SZ14F/FU Logic Diagram Truth Table IN A OUT Y A Y L H H L Operating Ranges Characteristics Symbol Supply voltage VCC Input voltage VIN Output voltage Rating 1.65 to 5.5 1.5 to 5.5 (Note 1) 0 to 5.5 VOUT Operating temperature Unit V 0 to 5.5 (Note 2) 0 to VCC (Note 3) −40 to 85 Topr V V °C Note 1: Date retention only Note 2: VCC = 0 V Note 3: High or Low State Electrical Characteristics DC Electrical Characteristics Characteristics Symbol Test Condition Ta = 25°C Typ. Max Ta = −40~85°C Min Max VCC (V) Min 1.65 0.6 1.0 1.4 0.65 1.4 1.8 0.7 1.1 1.5 0.7 1.5 2.3 1.0 1.4 1.8 1.0 1.8 3.0 1.3 1.75 2.2 1.3 2.2 4.5 1.9 2.45 3.1 1.9 3.1 Threshold 5.5 2.2 2.9 3.6 2.2 3.6 voltage 1.65 0.2 0.5 0.8 0.2 0.8 1.8 0.25 0.55 0.9 0.25 0.9 2.3 0.40 0.75 1.15 0.40 1.15 3.0 0.6 1.0 1.5 0.6 1.5 4.5 1.0 1.43 2.0 1.0 2.0 5.5 1.2 1.70 2.4 1.2 2.4 1.65 0.1 0.48 0.9 0.1 1.0 1.8 0.15 0.54 1.0 0.15 1.0 2.3 0.25 0.65 1.1 0.25 1.1 3.0 0.4 0.77 1.2 0.4 1.2 4.5 0.6 1.01 1.5 0.6 1.5 5.5 0.7 1.18 1.7 0.7 1.7 High level Low level Hysteresis voltage VP VN VH ⎯ ⎯ ⎯ 2 Unit V V 2007-11-01 TC7SZ14F/FU Characteristics Symbol Test Condition IOH = −100 μA High level VOH VIN = VIL Output VIN = VIH 1.65 1.55 1.65 ⎯ 1.55 ⎯ 1.8 1.7 1.8 ⎯ 1.7 ⎯ 2.3 2.2 2.3 ⎯ 2.2 ⎯ 3.0 2.9 3.0 ⎯ 2.9 ⎯ 4.4 4.5 ⎯ 4.4 ⎯ IOH = −4 mA 1.65 1.29 1.52 ⎯ 1.29 ⎯ IOH = −8 mA 2.3 1.9 2.15 ⎯ 1.9 ⎯ IOH = −16 mA 3.0 2.4 2.8 ⎯ 2.4 ⎯ IOH = −24 mA 3.0 2.3 2.68 ⎯ 2.3 ⎯ IOH = −32 mA 4.5 3.8 4.2 ⎯ 3.8 ⎯ 1.65 ⎯ 0 0.1 ⎯ 0.1 1.8 ⎯ 0 0.1 ⎯ 0.1 2.3 ⎯ 0 0.1 ⎯ 0.1 3.0 ⎯ 0 0.1 ⎯ 0.1 4.5 ⎯ 0 0.1 ⎯ 0.1 IOL = 4 mA 1.65 ⎯ 0.08 0.24 ⎯ 0.24 IOL = 8 mA 2.3 ⎯ 0.1 0.3 ⎯ 0.3 IOL = 16 mA 3.0 ⎯ 0.15 0.4 ⎯ 0.4 IOL = 24 mA 3.0 ⎯ 0.22 0.55 ⎯ 0.55 IOL = 100 μA VOL Ta = −40~85°C Min Max Min 4.5 voltage Low level Ta = 25°C Typ. Max VCC (V) IOL = 32 mA Unit V 4.5 ⎯ 0.22 0.55 ⎯ 0.55 Input leakage current IIN VIN = 5.5 V or GND 0~5.5 ⎯ ⎯ ±1 ⎯ ±10 μA Power OFF leakage current IOFF VIN or VOUT = 5.5 V 0.0 ⎯ ⎯ 1 ⎯ 10 μA Quiescent supply current ICC VIN = 5.5 V or GND 1.65~5.5 ⎯ ⎯ 1 ⎯ 10 μA AC Electrical Characteristics (Unless otherwise specified Input: tr = tf = 3 ns) Characteristics Propagation delay time Symbol tpLH Test Condition CL = 15 pF, RL = 1 MΩ tpHL CL = 50 pF, RL = 500 Ω Input capacitance CIN Power dissipation capacitance CPD ⎯ (Note 4) Ta = 25°C Typ. Max Ta = −40~85°C Min Max Unit VCC (V) Min 1.65 2.0 9.1 15.0 2.0 15.6 1.8 2.0 7.6 12.5 2.0 13 2.5 ± 0.2 1.0 5.0 9.0 1.0 9.5 3.3 ± 0.3 1.0 3.7 6.3 1.0 6.5 5.0 ± 0.5 0.5 3.1 5.2 0.5 5.5 3.3 ± 0.3 1.5 4.4 7.2 1.5 7.5 5.0 ± 0.5 0.5 3.7 5.9 0.8 6.2 0~5.5 ⎯ 4 ⎯ ⎯ ⎯ pF 3.3 ⎯ 24 ⎯ ⎯ ⎯ pF 5.5 ⎯ 30 ⎯ ⎯ ⎯ pF ns Note 4: CPD is defined as the value of the internal equivalent capacitance which is Calculated from the operating current consumption without load. Average operating current can be obtained by the equation. ICC (opr) = CPD･VCC･fIN + ICC 3 2007-11-01 TC7SZ14F/FU Package Dimensions Weight: 0.016 g (typ.) 4 2007-11-01 TC7SZ14F/FU Package Dimensions Weight: 0.006 g (typ.) 5 2007-11-01 TC7SZ14F/FU RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2007-11-01