ETC2 MGB-125M0DT Gbic transceiver Datasheet

GBIC Transceiver
MGB-243S
HG Genuine
GBIC Transceiver
MGB-243S
Features:
Operating temperature
range 0°C to +70°C
Operating bit rate
1250Mbps
Hot-pluggable
capability.
Low power dissipation
1310 nm FP laser
SCA-2 electrical
interface
Single 3.3V/5V power
supply
Differential PECL
input and output
TTL signal detect
indicator
Duplex SC optical
interface
Detailed product
information in
E2PROM
Applications:
Gigabit Ethernet
Switch to Switch interface
Router/server interface
Other optical transmission systems
Description:
MGB-243S is compliant with Gigabit Interface Converter (GBIC)
specification Rev5.5. It meets the requirements of IEEE 802.3 Gigabit
Ethernet standard and ANSI specifications for fiber channel. It can be inserted
in or removed from host chassis without shutting power of the host system.
MGB-243S Operating Wavelength is 1310nm, it enables cost-effective data
transmission over optical fibers at a distance of 10 km. The operating voltage
is +3.3V or +5V.
Specifications:
Absolute Maximum Ratings
Parameter
Symbol
Min
Supply Voltage
VCC
Ambient Operating
Temperature
Max
Unit
-0.5
6
V
TC
0
70
°C
Storage Temperature
Tstg
-40
85
°C
Relative Humidity
RH
5
95
%
Data Input Voltage
TX-DAT
-0 .5
VDDT
V
2000
mVp-p
300
mA
Transmitter Differential
Input Voltage
Operating Current
±TX-DAT
Iop
—
Typ
1of7
GBIC Transceiver
MGB-243S
HG Genuine
Transceiver Electrical Characteristics
Parameter
Symbol
Surge Current
ISURGE
Power Dissipation
PDISS
Min
Typ
Max
Unit
Note
30
mA
0.5
1.0
W
3.3V
0.8
1.5
W
5V
Transmitter Electro-optical Characteristics
Parameter
Output Optical Power
9/125um SMF
Symbol
Min
Typ
Max
Unit
PO
-9.5
7
-3
dBm
avg
Optical Extinction Ratio
9
λC
Center Wavelength
Note
dB
1280
1310
Spectral Width
1340
nm
2.8
nm rms
Optical Rise /Fall Time
tr/tf
0.26
ns
Total Contributed Jitter
TJ
227
ps p-p
POFF
-35
dBm
Max. Pout TX-DISABLE Asserted
Output Eye
Compliant with IEEE802.3z
Differential Input Voltage
VDIFF
0.65
2.0
V
Transmit Fault Output-Low
TX-FAULTL
0
0.5
V
Transmit Fault Output-High
TX-FAULTH
2.4
VCC
V
TX-DISABLE Assert Time
t-off
10
us
TX-DISABLE Negate Time
t-on
1
ms
Time to initialize, includes reset of
TX-FAULT
t-init
300
ms
TX-FAULT from fault to assertion
t-fault
100
us
TX-DISABLE time to start reset
t-reset
10
Symbol
Min
us
Receiver Electro-optical Characteristics
Parameter
Typ
Max
Unit
Note
7
Input Optical Power
Pin
-23
Operating Center Wavelength
λC
1200
Return Loss
ORL
12
Receiver Loss of Signal-TTL low
PRX-LOS A
Receiver Loss of Signal-TTL high
PRX-LOS D
-31
Receiver Differential Output Voltage
±RX_DAT
370
Receiver Output Rise Time
TrRx_DAT
Receiver Output Fall Time
TfRX_DAT
Receiver Loss of Light Load
RX-LOSLoad
Receiver Loss of Signal
Output Voltage -low
Receiver Loss of Signal
Output Voltage -high
7
-3
dBm
1660
nm
2 -1 PRBS
BER<10-12
dB
-23
dBm
dBm
2000
mV-p
0.25
0.35
ns
0.25
0.35
ns
4.7
10
KΩ
RX-LOSL
0.0
0.5
V
RX-LOSH
VCC-0.5
VCC+0.3
V
2of7
GBIC Transceiver
MGB-243S
HG Genuine
Receiver Loss of Signal
Assert Time _Logic low to high
tA, RX-LOS
100
us
Receiver Loss of Signal
Assert Time _Logic high to low
tD, RX-LOS
100
us
Pin Figure:
Figure 1
Pin Definitions:
Pin
Signal Name
Description
1
RX-LOS
2
RGND
Receiver Ground
3
RGND
Receiver Ground
4
MOD_DEF(0)
TTL Low
5
MOD_DEF(1)
SCL Serial Clock Signal
6
MOD_DEF(2)
SDA Serial Data Signal
7
TX-DISABLE
Transmitter Disable
8
TGND
Transmitter Ground
9
TGND
Transmitter Ground
10
TX-FAULT
11
RGND
12
-RX_DAT
Receiver Data, Differential PECL, AC coupled
13
+RX_DAT
Receiver Data, Differential PECL, AC coupled
14
RGND
Receiver Ground
15
VDDR
Receiver supply
16
VDDT
Transmitter supply
17
TGND
Transmitter Ground
18
+TX_DAT
Transmitter Data, Differential PECL, AC coupled
19
-TX_DAT
Transmitter Data, Differential PECL, AC coupled
20
TGND
Receiver Loss of Signal, TTL high, open collector
Transmit Fault
Receiver Ground
Transmitter Ground
Functions Description:
The laser is driven by a LD driver IC which converts differential input LVPECL (3.3V) or PECL (5V) logic
signals into an analog laser driving current.
MGB-243X complies with Module Definition 4. It features an EEPROM that contains the detailed product
3of7
GBIC Transceiver
MGB-243S
HG Genuine
information stored for retrieval by host equipment. This information is accessed via the 2-wire serial CMOS
EEPROM protocol of ATMEL AT24C01A.
TX_Fault
When sensing an improper power level in the laser driver, the GBIC set this signal high and turns off the Laser.
TX_FAULT can be reset with the TX_DISABLE line. The signal is in TTL level.
TX_Disable
The TX_DISABLE signal is high (TTL logic "1") to turn off the laser output. The laser will turn on within
1ms when TX_DISABLE is low (TTL logic "0").
Receive Loss (RX_LOS)
The RX_LOS is high (logic "1") when there is no incoming light from the companion transceiver. This signal
is normally used by the system for the diagnostic purpose. The signal is operated in TTL level.
Figure 2 shows the internal frame of GBIC, Figure3、4 show the typical eye diagrams of this product.
LA
RXdRXd+
DATA-
PT
DATA+
RXLOS
VCC
RECEIVEER
BIAS
TXd+
TXdTXdis
TX-FAULT
VCC
)
TRANSIMITER
DATA+
LD
MOD_DEF(1)
MOD_DEF(0
LASER DRIVER
MOD_DEF(2)
ID E2PROM
CONNECTOR
jimper
PM
Figure 2: Internal Frame
4of7
GBIC Transceiver
MGB-243S
HG Genuine
Figure 3: Receiver Eye Diagram
Figure4: Transmitter Eye Diagram
7
Note: measured with a 2 -1 PRBS test pattern @1.25Gbps
Interface Circuit
Figure 5 shows the recommended interface circuit for GBIC application.
Host Board
GBIC Module
DC+5V/+3.3V
DC+5V/+3.3V
4.7K to 10K
4.7K to 10K
TX-DISABLE
TX-FAULT
DC+5V/+3.3V
PECL
Note A
SerDat OUT+
Z0=75
TX-DAT
SerDat OUT-
Z0=75
TX-DATQ
serDat IN-
Z0=75
RX-DATQ
serDat IN+
Z0=75
RX-DAT
Laser
driver
2X180
DC+5V/+3.3V
PECL
Amplifier
DC+5V/+3.3V
4.7K to 10K
RX-LOS
DC+5V/+3.3V
3X4.7K to 10K
MOD-DEF(2)
MOD-DEF(1)
EEPROM
MOD-DEF(0)
GNDR
Figure 5: Interface Circuit
5of7
GBIC Transceiver
MGB-243S
HG Genuine
Figure Dimension: (Unit: mm)
Figure 6: Dimension
Unit: mm
11
36
65
30.4
6of7
GBIC Transceiver
MGB-243S
HG Genuine
Ordering Information:
Digital Transceiver Module
MGB
XX X X X X X
1
2
3
4
5
6
7
GBIC Module
Operating Level:
C:PECL; T:TTL
Laser Type:
F:F-P(omit); D:DFB ; V:VCSEL(omit)
Operating Voltage:
0: 3.3V or 5V currency(omit); 5:5V
Transmit Distance:
S:short distance;M:middle distance;
L:long distance; U:super long distance
Operating Wavelength:
3:1310nm;5:1550nm;8:850nm
Operating Rate:
03:155Mb/s 12:622Mb/s
24:1.25Gb/s 48:2.5Gb/s
Statement:
HG Genuine possesses the authority for ultimate explanation of the content; all information contained in this document is
subject to change without notice.
All information contained in this document was obtained in specific environments; the users should responsible for
verifying the products performance in their own operating environments. HG Genuine is not liable for the performance of
users' products. All information contained in this document is only for the users' reference and is not the verification of the
product quality.
Version:
V2.1
Publishing Date: 2005-05-07
Contact Information:
Address: Huagong Tech BDG, Science &Technology Region of Hust,
Donghu High-Tech Zone, Wuhan Hubei, P.R.China
Post Code: 430223
Tel: +86-27-87180203
Website: http://www.genuine-opto.com
7of7
Similar pages