ASIX AX88172A Usb 2.0 to 10/100m fast ethernet controller Datasheet

AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Features
Document No: AX88x72A/V1.1/12/24/07
Single chip USB 2.0 to 10/100M Fast Ethernet controller –
AX88772A
Single chip USB 2.0 to MII, single chip MII to Ethernet and
USB Bridging controller in Dual-PHY mode (submitted for
US patent application) – AX88172A
USB Device Interface
Integrates on-chip USB 2.0 transceiver and SIE
compliant to USB Spec 1.1 and 2.0
Supports USB Full and High Speed modes with
Bus-Power or Self-Power capability
Supports 4 or 6 programmable endpoints on USB
interface
High performance packet transfer rate over USB bus
using proprietary burst transfer mechanism (submitted for
US patent application)
Supports USB to Ethernet bridging or vice versa in
hardware
Fast Ethernet Controller
Integrates 10/100Mbps Fast Ethernet MAC/PHY
IEEE 802.3 10BASE-T/100BASE-TX compatible
Supports twisted pair crossover detection and
auto-correction (HP Auto-MDIX)
Embedded 16KB SRAM for RX packet buffering and
8KB SRAM for TX packet buffering
Supports both Full-duplex with flow control and
Half-duplex with backpressure operation
Supports 2 VLAN ID filtering, received VLAN Tag (4
bytes) can be stripped off or preserved
MAC/PHY loop-back diagnostic capability
Support Wake-on-LAN Function
Supports Suspend Mode and Remote Wakeup via
Link-up, Magic packet, MS wakeup frame and external
pin
Optional PHY power down during Suspend Mode
Versatile External Media Interface
Optional MII interface in MAC mode allows AX88172A
to work with external 100BASE-FX Ethernet PHY or
HomePNA PHY
Optional Reverse-MII or Reverse-RMII interface in PHY
mode allows AX88172A to work with external
HomePlug PHY or glueless MAC-to-MAC connections
Optional Reverse-MII interface in Dual-PHY mode
allows AX88172A to act as an Ethernet PHY or USB 2.0
PHY for external MAC device that needs Ethernet and
USB in system application
Supports 256/512 bytes (93c56/93c66) of serial EEPROM
(for storing USB Descriptors)
Supports automatic loading of Ethernet ID, USB Descriptors
and Adapter Configuration from EEPROM after power-on
initialization
Provides optional serial interface, I2C, SPI and UART
Integrates on-chip voltage regulator and only requires a
single 3.3V power supply
12MHz and 25Mhz clock input from either crystal or
oscillator source
Integrates on-chip power-on reset circuit
Small form factor with 64-pin LQFP (AX88772A) or 80-pin
TQFP (AX88172A) RoHS compliant package
Operating temperature range: 0°C to 70°C.
*IEEE is a registered trademark of the Institute of Electrical and
Electronic Engineers, Inc.
*All other trademarks and registered trademark are the property of their
respective holders.
Product Description
The AX88772A/AX88172A Low-pin-count USB 2.0 to 10/100M Fast Ethernet controller is a high performance and highly integrated
ASIC which enables low cost, small form factor, and simple plug-and-play Fast Ethernet network connection capability for desktops,
notebook PC’s, Ultra-Mobile PC’s, docking stations, game consoles, digital-home appliances, and any embedded system using a
standard USB port.
The AX88772A/AX88172A features a USB interface to communicate with a USB Host Controller and is compliant with USB
specification V1.1 and V2.0. The AX88772A/AX88172A implements 10/100Mbps Ethernet LAN function based on IEEE802.3, and
IEEE802.3u standards with 24KB of embedded SRAM for packet buffering. The AX88772A/AX88172A integrates an on-chip
10/100Mbps Ethernet PHY to simplify system design.
The AX88172A provides an optional External Media Interface (EMI) for external PHY or external MAC for different application
purposes. The EMI can be a media-independent interface (MII) for implementing 100BASE-FX Ethernet or HomePNA functions. The
EMI can also be a Reverse-MII or Reverse Reduced-MII (Reverse-RMII) for glueless MAC-to-MAC connections to any MCU with
Ethernet MAC MII or RMII interface. In addition, the EMI can be configured to Dual-PHY mode allowing AX88172A to act as an
Ethernet PHY or USB 2.0 PHY for external MAC device that needs Ethernet and USB interfaces in their system applications. The
optional serial interface such as I2C, SPI, and UART are provided as a control channel from the USB Host Controller to communicate
with the external MCU chip.
Always contact ASIX for possible updates before starting a design.
This data sheet contains new products information. ASIX ELECTRONICS reserves the rights to modify product specification without notice. No
liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
ASIX ELECTRONICS CORPORATION
4F, NO.8, Hsin Ann Rd., Hsinchu Science Park, Hsin-Chu City, Taiwan, R.O.C. 300
FAX: 886-3-579-9558
TEL: 886-3-579-9500
Released Date: 12/24/2007
http://www.asix.com.tw/
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Target Applications
PC/Internet
USB Dongle
Docking Station
Port Replicator
for Mobile Computer
UMPC
Media Gateway
USB KVME
Switch
Internet Security
USB Key
Card Reader UWB/802.11n/WiMAX
USB Dongle
Pocketable Computer
Consumer Electronics
Portable Media Player
IP STB
TiVo Box
ePiano
DVD-Recorder/DVR
Game Console
IPTV
Figure 1 : Target Applications
2
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Typical System Block Diagrams
Hosted by USB to operate with internal Ethernet PHY only
To USB 2.0 Host I/F
AX88772A
EEPROM
Ethernet PHY
SPI
I2C
UART
Magnetic
RJ45
Figure 2 : USB 2.0 to LAN Adaptor (MAC mode)
Hosted by USB to operate with either internal Ethernet PHY or EMI (in MAC mode)
To USB 2.0 Host I/F
AX88172A
EEPROM
Ethernet PHY
MDC MDIO
MII
SPI
I2C
UART
Magnetic
100BASE FX
PHY
or
HomePNA
PHY
RJ45
Magnetic
Fiber
RJ11
Figure 3 : USB 2.0 to Fast Ethernet and 100BASE-FX Fiber/HomePNA Combo (MAC mode)
3
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Hosted by USB to operate with either internal Ethernet PHY (in MAC mode) or EMI
(in PHY mode)
To USB 2.0 Host I/F
AX88172A
EEPROM
MDC MDIO
Ethernet PHY
Reverse-MII or Reverse-RMII
(No oscillator or buffer required)
SPI
I2C
UART
Magnetic
Ethernet MAC
Embedded MCU
RJ45
Figure 4
: Bridging Embedded MCU to USB 2.0 Host Interface (PHY mode)
To USB 2.0 Host I/F
AX88172A
EEPROM
Ethernet PHY
MDC MDIO
Reverse-MII or Reverse-RMII
(No oscillator or buffer required)
Magnetic
HomePlug
PHY
RJ45
PowerLine
Figure 5
: USB 2.0 to HomePlug Adaptor (PHY mode)
4
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Hosted by EMI to operate with either internal Ethernet PHY or USB PHY (in
Dual-PHY mode)
Embedded MCU
SPI
I2C
UART
Ethernet MAC
Reverse-MII
(No oscillator or buffer required)
MDC MDIO
AX88172A
EEPROM
Ethernet PHY
USB 2.0 device
Magnetic
To USB 2.0 Host I/F
RJ45
Figure 6
: Bridging Embedded MCU to either Ethernet PHY or USB 2.0 Interface
5
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Table of Contents
1.0 INTRODUCTION ................................................................................................................... 9
1.1
1.2
1.3
GENERAL DESCRIPTION ....................................................................................................................................... 9
BLOCK DIAGRAM ................................................................................................................................................ 9
PINOUT DIAGRAM.............................................................................................................................................. 10
2.0 SIGNAL DESCRIPTION ........................................................................................... 14
2.1
2.2
2.3
AX88772A 64-PIN PINOUT DESCRIPTION ......................................................................................................... 14
AX88172A 80-PIN PINOUT DESCRIPTION ......................................................................................................... 16
HARDWARE SETTING FOR OPERATION MODE AND MULTI-FUNCTION PINS ...................................................... 20
3.0 FUNCTION DESCRIPTION................................................................................. 20
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
USB CORE AND INTERFACE .............................................................................................................................. 20
10/100M ETHERNET PHY ................................................................................................................................. 20
MAC CORE ....................................................................................................................................................... 20
OPERATION MODE ............................................................................................................................................. 20
STATION MANAGEMENT (STA)......................................................................................................................... 20
MEMORY ARBITER ............................................................................................................................................ 20
USB TO ETHERNET BRIDGE .............................................................................................................................. 20
SERIAL EEPROM LOADER ............................................................................................................................... 20
GENERAL PURPOSE I/O...................................................................................................................................... 20
SERIAL INTERFACE CONTROLLER ...................................................................................................................... 20
CLOCK GENERATION ......................................................................................................................................... 20
RESET GENERATION .......................................................................................................................................... 20
VOLTAGE REGULATOR ...................................................................................................................................... 20
4.0 SERIAL EEPROM MEMORY MAP ........................................................ 20
4.1
DETAILED DESCRIPTION .................................................................................................................................... 20
5.0 USB CONFIGURATION STRUCTURE .............................................. 20
5.1
5.2
5.3
USB CONFIGURATION ....................................................................................................................................... 20
USB INTERFACE ................................................................................................................................................ 20
USB ENDPOINTS ............................................................................................................................................... 20
6.0 USB COMMANDS ............................................................................................................... 20
6.1
USB STANDARD COMMANDS ............................................................................................................................ 20
6.2
USB VENDOR COMMANDS ................................................................................................................................ 20
6.2.1
Detailed Register Description .................................................................................................................. 20
6.2.2
Command Block Wrapper for Serial Interface ......................................................................................... 20
6.2.2.1 UART controller ................................................................................................................................. 20
6.2.2.2 I2C controller ...................................................................................................................................... 21
6.2.2.3 SPI controller ...................................................................................................................................... 21
6.3
INTERRUPT ENDPOINT ....................................................................................................................................... 21
7.0 EMBEDDED ETHERNET PHY REGISTER
DESCRIPTION ........................................................................................................................................ 21
7.1
PHY REGISTER DETAILED DESCRIPTION........................................................................................................... 21
7.1.1
Basic Mode Control Register (BMCR) ..................................................................................................... 21
7.1.2
Basic Mode Status Register (BMSR)......................................................................................................... 21
7.1.3
PHY Identifier Register 1.......................................................................................................................... 21
6
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
7.1.4
7.1.5
7.1.6
7.1.7
PHY Identifier Register 2.......................................................................................................................... 21
Auto Negotiation Advertisement Register (ANAR) ................................................................................... 21
Auto Negotiation Link Partner Ability Register (ANLPAR) ..................................................................... 21
Auto Negotiation Expansion Register (ANER) ......................................................................................... 21
8.0 STATION MANAGEMENT REGISTERS IN
PHY/DUAL-PHY MODE ........................................................................................................... 21
8.1
PHY/DUAL-PHY MODE DETAILED REGISTER DESCRIPTION ............................................................................ 21
8.1.1
PHY Mode Basic Mode Control Register (PM_BMCR)........................................................................... 21
8.1.2
PHY Mode Basic Mode Status Register (PM_BMSR) .............................................................................. 21
8.1.3
PHY Mode PHY Identifier Register 1 ....................................................................................................... 21
8.1.4
PHY Mode PHY Identifier Register 2 ....................................................................................................... 21
8.1.5
PHY Mode Auto Negotiation Advertisement Register (PM_ANAR) ......................................................... 21
8.1.6
PHY Mode Auto Negotiation Link Partner Ability Register (PM_ANLPAR) ........................................... 21
8.1.7
PHY Mode Auto Negotiation Expansion Register (PM_ANER) ............................................................... 21
8.1.8
PHY Mode Control Register (PM_Control) ............................................................................................. 21
9.0 ELECTRICAL SPECIFICATIONS ............................................................ 22
9.1
DC CHARACTERISTICS ...................................................................................................................................... 22
9.1.1
Absolute Maximum Ratings ...................................................................................................................... 22
9.1.2
Recommended Operating Condition......................................................................................................... 22
9.1.3
Leakage Current and Capacitance ........................................................................................................... 23
9.1.4
DC Characteristics of 3.3V I/O Pins ........................................................................................................ 23
9.1.5
DC Characteristics of 3.3V with 5V Tolerance I/O Pins.......................................................................... 24
9.1.6
DC Characteristics of Voltage Regulator................................................................................................. 25
9.2
POWER CONSUMPTION ...................................................................................................................................... 26
9.3
POWER-UP SEQUENCE ....................................................................................................................................... 27
9.4
AC TIMING CHARACTERISTICS.......................................................................................................................... 28
9.4.1
Clock Timing............................................................................................................................................. 28
9.4.2
Reset Timing ............................................................................................................................................. 28
9.4.3
Serial EEPROM Timing............................................................................................................................ 29
9.4.4
MII Timing ................................................................................................................................................ 30
9.4.5
Station Management Timing..................................................................................................................... 31
9.4.6
Reverse-MII Timing .................................................................................................................................. 32
9.4.7
Reverse-RMII Timing................................................................................................................................ 33
9.4.8
I2C Interface Timing................................................................................................................................. 34
9.4.9
SPI Interface Timing................................................................................................................................. 35
9.4.10 10/100M Ethernet PHY Interface Timing ................................................................................................. 37
9.4.11 USB Transceiver Interface Timing ........................................................................................................... 38
10.0
10.1
10.2
PACKAGE INFORMATION ........................................................................... 40
AX88772A 64-PIN LQFP PACKAGE.................................................................................................................. 40
AX88172A 80-PIN TQFP PACKAGE.................................................................................................................. 41
11.0
ORDERING INFORMATION ........................................................................ 42
12.0
REVISION HISTORY ................................................................................................ 43
APPENDIX A. DEFAULT WOL READY MODE .................................................................... 44
7
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
List of Figures
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
FIGURE 5
FIGURE 6
FIGURE 7
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
: TARGET APPLICATIONS ................................................................................................................................. 2
: USB 2.0 TO LAN ADAPTOR (MAC MODE)................................................................................................... 3
: USB 2.0 TO FAST ETHERNET AND 100BASE-FX FIBER/HOMEPNA COMBO (MAC MODE) ........................ 3
: BRIDGING EMBEDDED MCU TO USB 2.0 HOST INTERFACE (PHY MODE).................................................... 4
: USB 2.0 TO HOMEPLUG ADAPTOR (PHY MODE).......................................................................................... 4
: BRIDGING EMBEDDED MCU TO EITHER ETHERNET PHY OR USB 2.0 INTERFACE ....................................... 5
: AX88772A/AX88172A BLOCK DIAGRAM ................................................................................................... 9
: AX88772A PINOUT DIAGRAM (MAC MODE WITHOUT MII)....................................................................... 10
: AX88172A PINOUT DIAGRAM (MAC MODE WITH MII) ............................................................................. 11
: AX88172A PINOUT DIAGRAM (PHY MODE WITH REVERSE-MII) .......................................................... 12
: AX88172A PINOUT DIAGRAM (PHY MODE WITH REVERSE-RMII)........................................................ 13
List of Tables
TABLE 1
TABLE 2
TABLE 3
: AX88772A 64-PIN PINOUT DESCRIPTION ................................................................................................... 14
: AX88172A 80-PIN PINOUT DESCRIPTION ................................................................................................... 16
: POWER CONSUMPTION ................................................................................................................................. 26
8
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
1.0 Introduction
1.1 General Description
The AX88772A/AX88172A Low-pin-count USB 2.0 to 10/100M Fast Ethernet controller is a high performance and
highly integrated ASIC which enables low cost, small form factor, and simple plug-and-play Fast Ethernet network
connection capability for desktops, notebook PC’s, Ultra-Mobile PC’s, docking stations, game consoles, digital-home
appliances, and any embedded system using a standard USB port.
The AX88772A/AX88172A features a USB interface to communicate with a USB Host Controller and is compliant with
USB specification V1.1 and V2.0. The AX88772A/AX88172A implements a 10/100Mbps Ethernet LAN function based
on IEEE802.3, and IEEE802.3u standards with 24KB of embedded SRAM for packet buffering. The
AX88772A/AX88172A integrates an on-chip 10/100Mbps Ethernet PHY to simplify system design.
The AX88172A provides an optional External Media Interface (EMI) for external PHY or external MAC for different
application purposes. The EMI can be a media-independent interface (MII) for implementing 100BASE-FX Ethernet or
HomePNA functions. The EMI can also be a Reverse-MII or Reverse Reduced-MII (Reverse-RMII) for glueless
MAC-to-MAC connections to any MCU with Ethernet MAC MII or RMII interface. In addition, the EMI can be
configured to Dual-PHY mode allowing AX88172A to act as an Ethernet PHY or USB 2.0 PHY for external MAC device
that needs Ethernet and USB interfaces in their system applications. The optional serial interface such as I2C, SPI, and
UART are provided as a control channel from the USB Host Controller to communicate with the external MCU chip.
The AX88772A/AX88172A needs 12MHz clock for USB operation and 25Mhz clock for Fast Ethernet operation. The
AX88772A is housed in the 64-pin LQFP and the AX88172A is housed in the 80-pin TQFP RoHS compliant package.
1.2 Block Diagram
24KB SRAM
EECS
EECK
EEDIO
SEEPROM
Loader I/F
GPIO_2~0
General Purpose
I/O
MAC
Core
Memory
Arbiter
10/100M
Ethernet
PHY
AX88172A only
USB to
Ethernet
Bridge
PHY/MAC
mode Bridge
STA
SI_3~0
Serial I/F
Controller:
UART/I2C/SPI
3.3 to 1.8V
Regulator
External Media Interface
MII /
Reverse-MII /
Reverse-RMII
MDC / MDIO
USB Core and Interfaces
PLL Clock
Generators
XTL25P, XTL25N
XTL12P, XTL12N
Figure 7
RXIP/RXIN
TXOP/TXON
Power-On-Reset
& Reset Gen.
DP/DM
RESET_N
: AX88772A/AX88172A Block Diagram
9
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
1.3 Pinout Diagram
VCCK
GND
EECK
EECS
EEDIO
TCLK_1
TCLK_0
TCLK_EN
VCC3IO
RESET_N
TEST1
TEST0
GND
GND
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
49
50
51
52
53
54
55
56
(MAC mode without MII)
57
58
59
60
61
62
63
64
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Figure 8
32 SI_0
31 SI_1
30 SI_2
29 SI_3
28 GPIO_0 / PME
27 GPIO_1
26 GPIO_2
25 VCCK
24 EXTWAKEUP_N
23 GND
22 USB_LED
21 VCCK
20 LINK_LED
19 SPEED_LED
18 FDX_LED
17 VCC3IO
GND
GND
VCCK
VCCK
GND3R3
VCC3R3
V18F
GND18A
TXON
TXOP
VCC18A
RXIN
RXIP
GND3A3
VCC3A3
AX88772A
RSET_BG
VCC3IO
VCCK
XTL12P
XTL12N
VCC33A_H
GND33A_H
RREF
DM
DP
VCC33A_PLL
GND33A_PLL
GND
VCC18A
XTL25P
XTL25N
GND18A
VCCK
V_BUS
AX88772A in 64-pin LQFP package
: AX88772A Pinout Diagram (MAC mode without MII)
10
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
VCCK
GND
MDIO
MDC
EECK
EECS
EEDIO
TCLK_1
TCLK_0
TCLK_EN
VCC3IO
RESET_N
TEST1
TEST0
GND
GND
VCCK
V_BUS
TXD3
TXD2
AX88172A in 80-pin TQFP package - MAC mode with MII
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
40 SI_0
39 SI_1
38 SI_2
37 SI_3
36 GPIO_0 / PME
35 GPIO_1
34 GPIO_2
33 VCCK
32 COL
31 CRS
30 EXTWAKEUP_N
29 GND
28 USB_LED
27 VCCK
26 LINK_LED
25 SPEED_LED
24 FDX_LED
23 RXD0
22 RXD1
21 VCC3IO
AX88172A
RXD2
RXD3
RXDV
RXCLK
GND
GND
VCCK
VCCK
GND3R3
9 10 11 12 13 14 15 16 17 18 19 20
VCC3R3
RXIN
8
V18F
RXIP
Figure 9
6 7
GND18A
5
TXON
4
TXOP
3
VCC18A
2
GND3A3
(MAC mode with MII)
VCC3A3
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
0 1
RSET_BG
TXD1
TXD0
TXCLK
TXEN
VCC3IO
VCCK
XTL12P
XTL12N
VCC33A_H
GND33A_H
RREF
DM
DP
VCC33A_PLL
GND33A_PLL
GND
VCC18A
XTL25P
XTL25N
GND18A
: AX88172A Pinout Diagram (MAC mode with MII)
11
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
VCCK
GND
MDIO
MDC
EECK
EECS
EEDIO
TCLK_1
TCLK_0
TCLK_EN
VCC3IO
RESET_N
TEST1
TEST0
GND
GND
VCCK
V_BUS
RXD3
RXD2
AX88172A in 80-pin TQFP package - PHY mode with Reverse-MII
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
RXD1 61
RXD0 62
RXCLK 63
RXDV 64
VCC3IO 65
VCCK 66
XTL12P 67
XTL12N 68
VCC33A_H 69
GND33A_H 70
(PHY mode with Reverse-MII)
RREF 71
DM 72
DP 73
VCC33A_PLL 74
GND33A_PLL 75
GND 76
VCC18A 77
XTL25P 78
XTL25N 79
GND18A 80
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
TXD2
TXD3
TXEN
TXCLK
GND
GND
VCCK
VCCK
GND3R3
VCC3R3
V18F
GND18A
TXON
TXOP
VCC18A
RXIN
RXIP
GND3A3
VCC3A3
RSET_BG
AX88172A
40 SI_0
39 SI_1
38 SI_2
37 SI_3
36 GPIO_0 / PME
35 GPIO_1
34 RXER
33 VCCK
32 COL
31 CRS
30 EXTWAKEUP_N
29 GND
28 USB_LED
27 VCCK
26 LINK_LED
25 SPEED_LED
24 FDX_LED
23 TXD0
22 TXD1
21 VCC3IO
Figure 10 : AX88172A Pinout Diagram (PHY mode with Reverse-MII)
12
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
VCCK
GND
MDIO
MDC
EECK
EECS
EEDIO
TCLK_1
TCLK_0
TCLK_EN
VCC3IO
RESET_N
TEST1
TEST0
GND
GND
VCCK
V_BUS
MIS_1
MIS_0
AX88172A in 80-pin TQFP package - PHY mode with Reverse-RMII
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
40 SI_0
39 SI_1
38 SI_2
37 SI_3
36 GPIO_0 / PME
35 GPIO_1
34 RXER
33 VCCK
32 NC
31 NC
30 EXTWAKEUP_N
29 GND
28 USB_LED
27 VCCK
26 LINK_LED
25 SPEED_LED
24 FDX_LED
23 TXD0
22 TXD1
21 VCC3IO
AX88172A
NC
NC
TXEN
GND
REFCLK_I
GND
VCCK
VCCK
GND3R3
9 10 11 12 13 14 15 16 17 18 19 20
VCC3R3
RXIN
8
V18F
RXIP
6 7
GND18A
5
TXON
4
TXOP
3
VCC18A
2
GND3A3
(PHY mode with Reverse-RMII)
VCC3A3
RSET_BG
RXD1 61
RXD0 62
REFCLK_O 63
CRSDV 64
VCC3IO 65
VCCK 66
XTL12P 67
XTL12N 68
VCC33A_H 69
GND33A_H 70
RREF 71
DM 72
DP 73
VCC33A_PLL 74
GND33A_PLL 75
GND 76
VCC18A 77
XTL25P 78
XTL25N 79
GNDK18A 80
0 1
Figure 11 : AX88172A Pinout Diagram (PHY mode with Reverse-RMII)
13
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
2.0 Signal Description
The following abbreviations apply to the following pin description table.
I18
I3
I5
O3
O5
B5
Input, 1.8V
AO Analog Output
Input, 3.3V
AB Analog Bi-directional I/O
Input, 3.3V with 5V tolerant
PU Internal Pull Up (75K)
Output, 3.3V
PD Internal Pull Down (75K)
Output, 3.3V with 5V tolerant
P
Power Pin
Bi-directional I/O, 3.3V with 5V
S
Schmitt Trigger
tolerant
T
Tri-stateable
AI
Analog Input
Note: Every output or bi-directional I/O pin is 8mA driving strength.
2.1 AX88772A 64-pin Pinout Description
Table 1
Pin Name
Type
Pin No
DP
DM
VBUS
XTL12P
AB
AB
I5/PD/S
I3
57
56
48
51
XTL12N
RREF
O3
AI
52
55
EECK
B5/PD/
T
35
EECS
B5/PD/
T
36
EEDIO
B5/PU/
T
37
XTL25P
I18
62
XTL25N
RXIP
RXIN
TXOP
TXON
RSET_BG
O18
AB
AB
AB
AB
AO
63
4
5
7
8
1
LINK_LED
O5
20
: AX88772A 64-pin Pinout Description
Pin Description
USB Interface
USB 2.0 data positive pin.
USB 2.0 data negative pin.
VBUS pin input. Please connect to USB bus power.
12Mhz ±0.003%crystal or oscillator clock input. This clock is needed for
USB PHY transceiver to operate.
12Mhz crystal or oscillator clock output.
For USB PHY’s internal biasing. Please connect to analog GND through a
resistor (12.1Kohm ±1%).
Serial EEPROM Interface
EEPROM Clock. EECK is an output clock to EEPROM to provide timing
reference for the transfer of EECS, and EEDIO signals. EECK only drive
high / low when access EEPROM otherwise keep at tri-state and internal
pull-down.
EEPROM Chip Select. EECS is asserted high synchronously with respect to
rising edge of EECK as chip select signal. EECS only drive high / low when
access EEPROM otherwise keep at tri-state and internal pull-down.
EEPROM Data In. EEDIO is the serial output data to EEPROM’s data input
pin and is synchronous with respect to the rising edge of EECK. EEDIO
only drive high / low when access EEPROM otherwise keep at tri-state and
internal pull-up.
Ethernet PHY Interface
25Mhz ± 0.005% crystal or oscillator clock input. This clock is needed for
the embedded 10/100M Ethernet PHY to operate.
25Mhz crystal or oscillator clock output.
Receive data input positive pin for both 10BASE-T and 100BASE-TX.
Receive data input negative pin for both 10BASE-T and 100BASE-TX.
Transmit data output positive pin for both 10BASE-T and 100 BASE-TX
Transmit data output negative pin for both 10BASE-T and 100 BASE-TX
For Ethernet PHY’s internal biasing. Please connect to GND through a
12.1Kohm ±1% resistor.
Link status LED indicator. This pin drives low continuously when the
Ethernet link is up and drives low and high in turn (blinking) when Ethernet
PHY is in receiving or transmitting state.
14
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
FDX_LED
O5
18
Full Duplex and collision detected LED indicator. This pin drives low when
the Ethernet PHY is in full-duplex mode and drives high when in half
duplex mode. When in half duplex mode and the Ethernet PHY detects
collision, it will be driven low (or blinking).
SPEED_LED
O5
19 Ethernet speed LED indicator. This pin drives low when the Ethernet PHY
is in 100BASE-TX mode and drives high when in 10BASE-T mode.
Misc. Pins
RESET_N
I5/PU/S 42 Chip reset input. Active low. This is the external reset source used to reset
this chip. This input feeds to the internal power-on reset circuitry, which
provides the main reset source of this chip. After completing reset,
EEPROM data will be loaded automatically.
EXTWAKEUP_N I5/PU/S
24 Remote-wakeup trigger from external pin. EXTWAKEUP_N should be
asserted low for more than 2 cycles of 12MHz clock to be effective.
GPIO_2
B5/PD
26 General Purpose Input/ Output Pin 2.
GPIO_1
B5/PD
27 General Purpose Input/ Output Pin 1. This pin is default as input pin after
power-on reset. This pin is also for Default WOL Ready Mode setting;
please refer to section 2.3 Settings.
GPIO_0/PME
B5/PD
28 General Purpose Input/ Output Pin 0 or PME (Power Management Event).
This pin is default as input pin after power-on reset. GPIO_0 also can be
defined as PME output to indicate wake up event detected. Please refer to
section 2.3 Settings.
SI_3
B5/PU
29 UART_RX or SPI_MISO. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
SI_2
B5/PU
30 UART_TX or SPI_MOSI. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
SI_1
B5/PU
31 I2C_SDA or SPI_SS. This is a multi-function pin determined by EEPROM
Flag [1] setting. Please refer to section 2.3 Settings.
SI_0
B5/PU
32 I2C_SCLK or SPI_SCLK. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
USB_LED
O5
22 USB Speed indicator: When USB bus is in Full speed, this pin drives high
continuously. When USB bus is in High speed, this pin drives low
continuously. This pin drives high and low in turn (blinking) to indicate TX
data transfer going on whenever the host controller sends bulk out data
transfer.
TEST0
I5/S
44 Test pin. For normal operation, user should connect to ground.
TEST1
I5/S
43 Test pin. For normal operation, user should connect to ground.
TCLK_EN
I5/PD/S 40 Test pin. For normal operation, user should keep this pin NC.
TCLK_0
I5/PD
39 Test pin. For normal operation, user should keep this pin NC.
TCLK_1
I5/PD
38 Test pin. For normal operation, user should keep this pin NC.
On-chip Regulator Pins
VCC3R3
P
11 3.3V Power supply to on-chip 3.3V to 1.8V voltage regulator.
GND3R3
P
12 Ground pin of on-chip 3.3V to 1.8V voltage regulator.
V18F
P
10 1.8V voltage output of on-chip 3.3V to 1.8V voltage regulator.
Power and Ground Pins
VCCK
P
13, 14, 21, 25, Digital Core Power. 1.8V.
33, 47, 50
VCC3IO
P
17, 41, 49
Digital I/O Power. 3.3V.
GND
P
15, 16, 23, 34, Digital Ground.
45, 46, 60
VCC33A_H
P
53
Analog Power for USB transceiver. 3.3V.
GND33A_H
P
54
Analog Ground for USB transceiver.
VCC33A_PLL
P
58
Analog Power for USB PLL. 3.3V.
GND33A_PLL
P
59
Analog Ground for USB PLL.
VCC3A3
P
2
Analog Power for Ethernet PHY bandgap. 3.3V.
GND3A3
P
3
Analog Ground for Ethernet PHY.
VCC18A
P
6, 61
Analog Power for Ethernet PHY and 25Mhz crystal oscillator.
1.8V.
15
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
GND18A
P
9, 64
Analog Ground for Ethernet PHY and 25Mhz crystal oscillator.
2.2 AX88172A 80-pin Pinout Description
Table 2
Pin Name
Type
Pin No
DP
DM
VBUS
XTL12P
AB
AB
I5/PD/S
I3
73
72
58
67
XTL12N
RREF
O3
AI
68
71
EECK
B5/PD/
T
45
EECS
B5/PD/
T
46
EEDIO
B5/PU/
T
47
XTL25P
I18
78
XTL25N
RXIP
RXIN
TXOP
TXON
RSET_BG
O18
AB
AB
AB
AB
AO
79
4
5
7
8
1
LINK_LED
O5
26
FDX_LED
O5
24
SPEED_LED
O5
25
I5/PU/S
52
EXTWAKEUP_N I5/PU/S
30
GPIO_2 / RXER B5/PD
34
RESET_N
: AX88172A 80-pin Pinout Description
Pin Description
USB Interface
USB 2.0 data positive pin.
USB 2.0 data negative pin.
VBUS pin input. Please connect to USB bus power.
12Mhz ±0.003%crystal or oscillator clock input. This clock is needed for
USB PHY transceiver to operate.
12Mhz crystal or oscillator clock output.
For USB PHY’s internal biasing. Please connect to analog GND through a
resistor (12.1Kohm ±1%).
Serial EEPROM Interface
EEPROM Clock. EECK is an output clock to EEPROM to provide timing
reference for the transfer of EECS, and EEDIO signals. EECK only drive
high / low when access EEPROM otherwise keep at tri-state and internal
pull-down.
EEPROM Chip Select. EECS is asserted high synchronously with respect
to rising edge of EECK as chip select signal. EECS only drive high / low
when access EEPROM otherwise keep at tri-state and internal pull-down.
EEPROM Data In. EEDIO is the serial output data to EEPROM’s data
input pin and is synchronous with respect to the rising edge of EECK.
EEDIO only drive high / low when access EEPROM otherwise keep at
tri-state and internal pull-up.
Ethernet PHY Interface
25Mhz ± 0.005% crystal or oscillator clock input. This clock is needed for
the embedded 10/100M Ethernet PHY to operate.
25Mhz crystal or oscillator clock output.
Receive data input positive pin for both 10BASE-T and 100BASE-TX.
Receive data input negative pin for both 10BASE-T and 100BASE-TX.
Transmit data output positive pin for both 10BASE-T and 100 BASE-TX
Transmit data output negative pin for both 10BASE-T and 100 BASE-TX
For Ethernet PHY’s internal biasing. Please connect to GND through a
12.1Kohm ±1% resistor.
Link status LED indicator. This pin drives low continuously when the
Ethernet link is up and drives low and high in turn (blinking) when
Ethernet PHY is in receiving or transmitting state.
Full Duplex and collision detected LED indicator. This pin drives low
when the Ethernet PHY is in full-duplex mode and drives high when in
half duplex mode. When in half duplex mode and the Ethernet PHY
detects collision, it will be driven low (or blinking).
Ethernet speed LED indicator. This pin drives low when the Ethernet PHY
is in 100BASE-TX mode and drives high when in 10BASE-T mode.
Misc. Pins
Chip Reset Input. RESET_N pin is active low. When asserted, it puts the
entire chip into reset state immediately. After completing reset, EEPROM
data will be loaded automatically.
Remote-wakeup trigger from external pin. EXTWAKEUP_N should be
asserted low for more than 2 cycles of 12MHz clock to be effective.
General Purpose Input/ Output Pin 2. This pin is GPIO_2 in MAC mode,
but it will be redefined as RXER (receive error) or GPIO_2 depending on
EEPROM Flag [3] in PHY mode.
16
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
GPIO_1
B5/PD
GPIO_0 / PME
B5/PD
SI_3
B5/PU
SI_2
B5/PU
SI_1
B5/PU
SI_0
B5/PU
USB_LED
O5
TEST0
TEST1
TCLK_EN
TCLK_0
TCLK_1
I5/S
I5/S
I5/PD/S
I5/PD
I5/PD
VCC3R3
GND3R3
V18F
P
P
P
VCCK
P
VCC3IO
GND
P
P
VCC33A_H
GND33A_H
VCC33A_PLL
GND33A_PLL
VCC3A3
GND3A3
VCC18A
GND18A
P
P
P
P
P
P
P
P
RXCLK
I5/PD
RXDV
I5/PD
RXD [3:0]
I5/PD
CRS
I5/PD
COL
I5/PD
35
General Purpose Input/ Output Pin 1. This pin is default as input pin after
power-on reset. This pin is also for Default WOL Ready Mode setting;
please refer to section 2.3 Settings.
36
General Purpose Input/ Output Pin 0 or PME (Power Management Event).
This pin is default as input pin after power-on reset. GPIO_0 also can be
defined as PME output to indicate wake up event detected. Please refer to
section 2.3 Settings.
37
UART_RX or SPI_MISO. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
38
UART_TX or SPI_MOSI. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
39
I2C_SDA or SPI_SS. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
40
I2C_SCLK or SPI_SCLK. This is a multi-function pin determined by
EEPROM Flag [1] setting. Please refer to section 2.3 Settings.
28
USB Speed indicator: When USB bus is in Full speed, this pin drives high
continuously. When USB bus is in High speed, this pin drives low
continuously. This pin drives high and low in turn (blinking) to indicate
TX data transfer going on whenever the host controller sends bulk out data
transfer.
54
Test pin. For normal operation, user should connect to ground.
53
Test pin. For normal operation, user should connect to ground.
50
Test pin. For normal operation, user should keep this pin NC.
49
Test pin. For normal operation, user should keep this pin NC.
48
Test pin. For normal operation, user should keep this pin NC.
On-chip Regulator Pins
11
3.3V Power supply to on-chip 3.3V-to-1.8V voltage regulator.
12
Ground pin of on-chip 3.3V-to-1.8V voltage regulator.
10
1.8V voltage output of on-chip 3.3V-to-1.8V voltage regulator.
Power and Ground Pins
13, 14, 27, 33, Digital Core Power. 1.8V.
41, 57, 66,
21, 51, 65 Digital I/O Power. 3.3V.
15, 16, 29, 42, Digital Ground.
55, 56, 76
69
Analog Power for USB transceiver. 3.3V.
70
Analog Ground for USB transceiver.
74
Analog Power for USB PLL. 3.3V.
75
Analog Ground for USB PLL.
2
Analog Power for Ethernet PHY bandgap. 3.3V.
3
Analog Ground for Ethernet PHY.
6, 77
Analog Power for Ethernet PHY and 25Mhz crystal oscillator. 1.8V.
9, 80
Analog Ground for Ethernet PHY and 25Mhz crystal oscillator.
External Media Interface: MAC Mode with MII Interface
17
Receive Clock. RXCLK is received from PHY to provide timing reference
for the transfer of RXD [3:0] and RXDV signals on receive direction of
MII interface.
18
Receive Data Valid. RXDV is asserted high when valid data is present on
RXD [3:0]. It is driven synchronously with respect to RXCLK by PHY.
19, 20, Receive Data. RXD [3:0] is driven synchronously with respect to RXCLK
22, 23 by PHY.
31
Carrier Sense. CRS is asserted high asynchronously by the PHY when
either transmit or receive medium is non-idle.
32
Collision. COL is driven high by PHY when the collision is detected.
17
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
TXCLK
I5/PD
TXEN
O3
TXD [3:0]
O3
MDC
O3/PD
MDIO
B5/PU
TXCLK
TXEN
TXD [3:0]
CRS
COL
RXER
RXCLK
RXDV
RXD [3:0]
MDC
MDIO
REFCLK_I
63
Transmit Clock. TXCLK is received from PHY to provide timing
reference for the transfer of TXD [3:0] and TXEN signals on transmit
direction of MII interface.
64
Transmit Enable. TXEN is asserted high to indicate a valid TXD [3:0]. It is
transitioned synchronously with respect to the rising edge of TXCLK.
59, 60, Transmit Data. TXD [3:0] is transitioned synchronously with respect to
61, 62 the rising edge of TXCLK. Note TXD [3:2] are also used as Chip
Operation Mode selection pins; please refer to section 2.3 Settings.
44
Station management clock output to PHY. All data transferred on MDIO
are synchronized to the rising edge of this clock. The frequency of MDC is
1.5MHz.
43
Station management data input/output. Serial data input/output transferred
from/to the PHYs. The transfer protocol conforms to the IEEE 802.3u MII
spec.
External Media Interface: PHY Mode with Reverse-MII Interface
O3/T
17
Transmit Clock. This clock is provided to supply to the TX_CLK of
externally connected Ethernet MAC device with MII. This pin is tri-stated
in isolate mode.
I5/PD
18
Transmit enable. TXEN is asserted high to indicate a valid TXD [3:0]. It
should be driven synchronously with respect to the rising edge of TXCLK
by the externally connected Ethernet MAC device with MII.
I5/PD
19, 20, Transmit Data. TXD [3:0] should be driven synchronously with respect to
22, 23 the rising edge of TXCLK by the externally connected Ethernet MAC
device with MII.
O3/PD/T
31
Carrier Sense. CRS is asserted high by AX88172A when RXDV is
asserted high in Reverse-MII mode. This pin is tri-stated in isolate mode.
O3/PD/T
32
Collision. COL is always driven low because AX88172A is operating in
100M/full-duplex mode internally in Reverse-MII mode. This pin is
tri-stated in isolate mode.
O3/PD/T
34
Receive Error. RXER is always driven low by AX88172A in Reverse-MII
mode. This pin is tri-stated in isolate mode.
O3/T
63
Receive clock. This clock is provided to supply to the RX_CLK of
externally connected Ethernet MAC device with MII. This pin is tri-stated
in isolate mode.
O3/T
64
Receive Data Valid. RXDV is asserted high when valid data is present on
RXD [3:0]. It is transitioned synchronously with respect to RXCLK from
AX88172A to the externally connected Ethernet MAC device with MII.
This pin is tri-stated in isolate mode.
O3/T
59, 60, Receive Data. RXD [3:0] is transitioned synchronously with respect to
61, 62 RXCLK from AX88172A to the externally connected Ethernet MAC
device with MII. Note that RXD [3:2] are also used as Chip Operation
Mode selection pins. Please refer to section 2.3 Settings. These pins are
tri-stated in isolate mode.
I5/PD
44
Station Management clock input from the externally connected Ethernet
MAC device. All data transferred on MDIO are synchronized to the rising
edge of this clock.
B5/PU
43
Station Management Data. Serial data input/output transferred from/to the
externally connected MAC device. The transfer protocol should conform
to the IEEE 802.3u MII spec.
External Media Interface: PHY Mode with Reverse-RMII Interface
I5
17
50Mhz +/-50ppm Reference clock input for RMII receive, transmit and
control signals. If externally connected Ethernet MAC device with RMII
can’t provide 50Mhz Reference clock to AX88172A, then user can
connect this pin to REFCLK_O and use REFCLK_O to supply clock to
the externally connected Ethernet MAC device at the same time.
18
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
TXEN
I5/PD
18
TXD [1:0]
I5/PD
22, 23
NC
NC
RXER
I5/PD
O3/PD
O3/PD/T
19, 20
31, 32
34
MIS_1
I5/PD
59
MIS_0
I5/PD
60
O3
63
CRSDV
O3/T
64
RXD [1:0]
O3/T
61, 62
MDC
I5/PD
44
MDIO
B5/PU
43
REFCLK_O
Transmit Enable from the externally connected Ethernet MAC device with
RMII.
Transmit Data from the externally connected Ethernet MAC device with
RMII.
NC
NC
Receive Error. RXER is always driven low by AX88172A in
Reverse-RMII mode. This pin is tri-stated in isolate mode.
External Media Interface Select 1. This is used as Chip Operation Mode
selection pin; please refer to section 2.3 Settings.
External Media Interface Select 0. This is used as Chip Operation Mode
selection pin; please refer to section 2.3 Settings.
50Mhz Reference clock output. If the externally connected Ethernet MAC
device can’t supply 50Mhz reference clock, this clock can be used to
supply to the REF_CLK of externally connected Ethernet MAC device
with RMII and the REFCLK_I of this chip.
Carrier Sense and Receive Data Valid to the externally connected Ethernet
MAC device with RMII. This pin is tri-stated in isolate mode.
Receive Data to the externally connected Ethernet MAC device with
RMII. These pins are tri-stated in isolate mode.
Station Management clock input from the externally connected Ethernet
MAC device. All data transferred on MDIO are synchronized to the rising
edge of this clock.
Station Management Data. Serial data input/output transferred from/to the
externally connected MAC device. The transfer protocol should conform
to the IEEE 802.3u MII spec.
19
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
2.3 Hardware Setting For Operation Mode And Multi-Function Pins
Please contact ASIX for receiving “AX88x72A Full Datasheet” which contains detailed description of section 2.3 and
section 3, 4, 5, 6, 7, 8.
3.0 Function Description
3.1 USB Core and Interface
3.2 10/100M Ethernet PHY
3.3 MAC Core
3.4 Operation Mode
3.5 Station Management (STA)
3.6 Memory Arbiter
3.7 USB to Ethernet Bridge
3.8 Serial EEPROM Loader
3.9 General Purpose I/O
3.10 Serial Interface Controller
3.11 Clock Generation
3.12 Reset Generation
3.13 Voltage Regulator
4.0 Serial EEPROM Memory Map
4.1 Detailed Description
5.0 USB Configuration Structure
5.1 USB Configuration
5.2 USB Interface
5.3 USB Endpoints
6.0 USB Commands
6.1 USB Standard Commands
6.2 USB Vendor Commands
6.2.1 Detailed Register Description
6.2.2 Command Block Wrapper for Serial Interface
6.2.2.1 UART controller
20
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
6.2.2.2 I2C controller
6.2.2.3 SPI controller
6.3 Interrupt Endpoint
7.0 Embedded Ethernet PHY Register Description
7.1 PHY Register Detailed Description
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.1.6
7.1.7
Basic Mode Control Register (BMCR)
Basic Mode Status Register (BMSR)
PHY Identifier Register 1
PHY Identifier Register 2
Auto Negotiation Advertisement Register (ANAR)
Auto Negotiation Link Partner Ability Register (ANLPAR)
Auto Negotiation Expansion Register (ANER)
8.0 Station Management Registers in PHY/Dual-PHY Mode
8.1 PHY/Dual-PHY Mode Detailed Register Description
8.1.1
8.1.2
8.1.3
8.1.4
8.1.5
8.1.6
8.1.7
8.1.8
PHY Mode Basic Mode Control Register (PM_BMCR)
PHY Mode Basic Mode Status Register (PM_BMSR)
PHY Mode PHY Identifier Register 1
PHY Mode PHY Identifier Register 2
PHY Mode Auto Negotiation Advertisement Register (PM_ANAR)
PHY Mode Auto Negotiation Link Partner Ability Register (PM_ANLPAR)
PHY Mode Auto Negotiation Expansion Register (PM_ANER)
PHY Mode Control Register (PM_Control)
21
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.0 Electrical Specifications
9.1 DC Characteristics
9.1.1 Absolute Maximum Ratings
Symbol
VCCK
Parameter
Digital core power supply
Rating
- 0.3 to 2.16
Unit
V
VCC18A
Analog Power. 1.8V
- 0.3 to 2.16
V
Power supply of 3.3V I/O
Power supply of on-chip voltage regulator
Analog Power 3.3V for Ethernet PHY bandgap
Analog Power 3.3V for USB PLL.
Analog Power 3.3V for USB TX and RX
Input voltage of 1.8V I/O
Input voltage of 3.3V I/O
- 0.3 to 4
- 0.3 to 4
- 0.3 to 3.8
- 0.3 to 4
- 0.3 to 4
- 0.3 to 2.16
- 0.3 to 4.0
V
V
V
V
V
V
V
Input voltage of 3.3V I/O with 5V tolerant
- 0.3 to 5.8
V
VCC3IO
VCC3R3
VCC3A3
VCC33A_PLL
VCC33A_H
VIN18
VIN3
TSTG
Storage temperature
- 40 to 150
℃
IIN
DC input current
20
mA
IOUT
Output short circuit current
20
mA
Note: Permanent device damage may occur if absolute maximum ratings are exceeded. Functional operation should be
restricted to the optional sections of this datasheet. Exposure to absolute maximum rating condition for extended periods
may affect device reliability.
9.1.2 Recommended Operating Condition
Symbol
VCCK
VCC18A
VCC3R3
VCC3IO
VCC33A_H
VCC33A_PLL
VCC3A3
VIN18
VIN3
Tj
Ta
Parameter
Digital core power supply
Analog core power supply
Power supply of on-chip voltage regulator
Power supply of 3.3V I/O
Analog Power 3.3V for USB TX and RX
Analog Power 3.3V for USB PLL.
Analog power supply for bandgap
Input voltage of 1.8 V I/O
Input voltage of 3.3 V I/O
Input voltage of 3.3 V I/O with 5V tolerance
Commercial junction operating temperature
Commercial operating temperature
Min
1.62
1.62
2.97
2.97
2.97
2.97
2.97
0
0
0
0
0
Thermal Characteristics
Symbol
Parameter
Thermal resistance of junction LQFP 64(AX88772A)
ΘJC
to case
TQFP 80(AX88172A)
Thermal resistance of junction Still air,LQFP 64(AX88772A)
ΘJA
to ambient
Still air,TQFP 80(AX88172A)
22
Typ
1.8
1.8
3.3
3.3
3.3
3.3
3.3
1.8
3.3
3.3
25
-
Max
1.98
1.98
3.63
3.63
3.63
3.63
3.63
1.98
3.63
5.25
125
70
Unit
V
V
V
V
V
V
V
V
V
V
℃
℃
Rating
13.1
27.5
45.1
55.2
Unit
°C/W
°C/W
°C/W
°C/W
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.1.3 Leakage Current and Capacitance
Symbol
IIN
IOZ
CIN
COUT
Parameter
Input current
Tri-state leakage current
Input capacitance
Conditions
No pull-up or pull-down
Output capacitance
Min
-10
-10
-
Typ
±1
±1
2.2
Max
10
10
-
Unit
μA
μA
pF
-
2.2
-
pF
CBID
Bi-directional buffer capacitance
2.2
pF
Note: The capacitance listed above does not include pad capacitance and package capacitance. One can estimate pin
capacitance by adding a pad capacitance of about 0.5pF to the package capacitance.
9.1.4 DC Characteristics of 3.3V I/O Pins
Symbol
VCC3IO
Tj
Vil
Vih
Vt
VtVt+
Vol
Voh
Rpu
Rpd
Iin
IOZ
Parameter
Conditions
Power supply of 3.3V I/O
3.3V I/O
Junction temperature
Input low voltage
LVTTL
Input high voltage
Switching threshold
Schmitt trigger negative going LVTTL
threshold voltage
Schmitt trigger positive going
threshold voltage
Output low voltage
Iol = 8mA
Output high voltage
Ioh = -8mA
Input pull-up resistance
Vin = 0
Input pull-down resistance
Vin = VCC3IO
Input leakage current
Vin = VCC3IO or 0
Input leakage current with pull-up Vin = 0
resistance
Input
leakage
current
with Vin = VCC3IO
pull-down resistance
Tri-state output leakage current
23
Min Typ
2.97 3.3
0
25
2.0
1.5
0.8 1.1
Max
3.63
125
0.8
-
Unit
V
℃
V
V
V
V
-
1.6
2.0
V
2.4
40
40
-10
-15
75
75
±1
-45
0.4
190
190
10
-85
V
V
KΩ
KΩ
μA
μA
15
45
85
μA
-10
±1
10
μA
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.1.5 DC Characteristics of 3.3V with 5V Tolerance I/O Pins
Symbol
VCC3IO
Tj
Vil
Vih
Vt
VtVt+
Vol
Voh
Rpu
Rpd
Iin
IOZ
Parameter
Conditions
Power supply of 3.3V I/O
3.3V I/O
Junction temperature
Input low voltage
LVTTL
Input high voltage
Switching threshold
Schmitt trigger negative going LVTTL
threshold voltage
Schmitt trigger positive going
threshold voltage
Output low voltage
Iol = 8mA
Output high voltage
Ioh = -8mA
Input pull-up resistance
Vin = 0
Input pull-down resistance
Vin = VCC3IO
Input leakage current
Vin = 5.5V or 0
Input leakage current with pull-up Vin = 0
resistance
Input
leakage
current
with Vin = VCC3IO
pull-down resistance
Tri-state output leakage current
Vin = 5.5V or 0
24
Min Typ
2.97 3.3
0
25
2.0
1.5
0.8 1.1
Max
3.63
125
0.8
-
Unit
V
℃
V
V
V
V
-
1.6
2.0
V
2.4
40
40
0.4
190
190
-15
75
75
±5
-45
-85
V
V
KΩ
KΩ
μA
μA
15
45
85
μA
±10
μA
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.1.6 DC Characteristics of Voltage Regulator
Symbol
VCC3R3
Tj
Iload
V18F
Description
Power supply of on-chip
voltage regulator.
Operating junction
temperature.
Driving current.
Conditions
Cout
ESR
Typ Max Unit
3.3
3.6
V
0
25
125
℃
Normal operation
Standby mode enabled
Output voltage of on-chip VCC3R3 = 3.3V
voltage regulator.
Dropout voltage.
△V18F = -1%, Iload = 10mA
Line regulation.
VCC3R3 = 3.3V, Iload = 50mA
1.71
1.8
240
30
1.89
mA
mA
V
-
0.1
0.2
0.2
0.4
V
%/V
VCC3R3 = 3.3V, 1mA ≦ Iload
≦ 240mA
VCC3R3 = 3.3V,-40℃ ≦ Tj ≦
125℃
VCC3R3 = 3.3V
VCC3R3 = 3.3V
Quiescent current at 125 VCC3R3 = 3.3V
℃.
VCC3R3 = 3.3V
Output external capacitor.
Allowable effective series
resistance of external
capacitor.
-
0.02
0.05 %/mA
Vdrop
△V18F
(△VCC3R3 x V18F)
Load regulation.
△V18F
(△Iload x V18F)
Temperature coefficient.
△V18F
△Tj
Iq_25℃
Quiescent current at 25 ℃.
Iq_125℃
Min
3.0
25
0.1
-
+/-0.2 +/-0.5 mV/
℃
70
100 μA
100 125 μA
85
115 μA
125 170 μA
1
μF
0.5
1
Ω
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.2 Power Consumption
Symbol
IVCCK
IVCC18A
IVCC3IO
IVCC33A
IVCCK
IVCC18A
IVCC3IO
IVCC33A
IVCCK
IVCC18A
IVCC3IO
IVCC33A
IVCCK
VCC18A
IVCC3IO
IVCC33A
IVCCK
IVCC18A
IVCC3IO
IVCC33A
IVCCK
Description
Current Consumption of VCCK
Current Consumption of VCC18A
Current Consumption of VCC3IO
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Current Consumption of VCCK
Current Consumption of VCC18A
Current Consumption of VCC3IO
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Current Consumption of VCCK
Current Consumption of VCC18A
Current Consumption of VCC3IO
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Current Consumption of VCCK
Current Consumption of VCC18A
Current Consumption of VCC3IO
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Current Consumption of VCCK
Current Consumption of VCC18A
Current Consumption of VCC3IO
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Current Consumption of VCCK
IVCC18A
IVCC3IO
Current Consumption of VCC18A
Current Consumption of VCC3IO
IVCC33A
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Current Consumption of VCCK
Current Consumption of VCC18A
Current Consumption of VCC3IO
Current Consumption of VCC33A_H +
VCC33A_PLL + VCC33A_PLL
Power consumption of
AX88772A/AX88172A chip only
IVCCK
IVCC18A
IVCC3IO
IVCC33A
IDEVICE
Conditions
Operating at Ethernet
100Mbps full duplex
mode and USB High
speed mode
Typ
47.5
39.3
16.6
35.4
Max Unit
mA
mA
mA
mA
Operating at Ethernet
100Mbps full duplex
mode and USB Full
speed mode
44.3
39.3
12.9
28.7
mA
mA
mA
mA
Operating at Ethernet
10Mbps full duplex
mode and USB High
speed mode
19.3
6.3
8.3
38.8
mA
mA
mA
mA
Operating at Ethernet
10Mbps full duplex
mode and USB Full
speed mode
14.9
6.2
4.9
32.3
mA
mA
mA
mA
Suspend
(the embedded Ethernet
PHY is powered down)
2.0
49.3
0.7
0.2
μA
μA
mA
mA
19
mA
3.4
8.5
mA
mA
30.9
mA
22
3.4
11.5
36.9
mA
mA
mA
mA
AX88172A in USB
Full speed, Rev-MII
operation and internal
PHY power save
(BMCR[11] bit = 1)
AX88172A in USB
High speed, Rev-MII
operation and internal
PHY power save
(BMCR[11] bit = 1)
1.8V
3.3V
Min
100
70
mA
mA
220
mA
(Excluding VCC3R3)
ISYSTEM
Power consumption of AX88x72A demo
board
Table 3
Total of 3.3V
(Including VCC3R3
regulator supplies 1.8V to
VCCK and VCC18A)
: Power consumption
26
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.3 Power-up Sequence
At power-up, the AX88772A/AX88172A requires the VCC3R3/VCC3IO/VCC3A3/VCC33A_H/ VCC33A_PLL power
supply to rise to nominal operating voltage within Trise3 and the V18F/VCCK/VCC18A power supply to rise to nominal
operating voltage within Trise2.
Trise3
3.3V
VCC3R3/VCC3IO/VCC3A3
/VCC33A_H/ VCC33A_PLL
0V
Tdelay32
Trise2
1.8V
V18F/VCCK/VCC18A
0V
Symbol
Trise3
Trise2
Tdelay32
Parameter
3.3V power supply rise time
1.8V power supply rise time
3.3V rise to 1.8V rise time delay
Condition
From 0V to 3.3V
From 0V to 1.8V
27
Min
0.5
-5
Typ
-
Max
10
10
5
Unit
ms
ms
ms
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4 AC Timing Characteristics
Notice that the following AC timing specifications for output pins are based on CL (Output
load)=50pF.
9.4.1 Clock Timing
XTL12P
TP_XTL12P
TL_XTL12P
TH_XTL12P
VIH
VIL
Symbol
TP_XTL12P
TH_XTL12P
TL_XTL12P
Parameter
XTL12P clock cycle time
XTL12P clock high time
XTL12P clock low time
Condition
Min
-
Typ
83.33
41.6
41.6
Max
-
Unit
ns
ns
ns
Typ
40.0
20.0
20.0
Max
-
Unit
ns
ns
ns
XTL25P
TP_XTL25P
TL_XTL25P
TH_XTL25P
VIH
VIL
Symbol
TP_XTL25P
TH_XTL25P
TL_XTL25P
Parameter
XTL25P clock cycle time
XTL25P clock high time
XTL25P clock low time
Condition
Min
-
9.4.2 Reset Timing
XTL12P
RESET_N
Trst
Symbol
Trst
Description
Reset pulse width after XTL12P is running
Min
60
Typ
-
Max
Unit
120000 XTL12P clock cycle*
*: If the system applications require using hardware reset pin, RESET_N, to reset AX88772A/AX88172A during device
initialization or normal operation after VBUS pin is asserted, the above timing spec (Min=5μs, Max=10ms) of
RESET_N should be met.
28
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.3 Serial EEPROM Timing
T ch
T cl
T cl k
E E CK
T dv
T od
E E DIO (a s O UT P UT )
T l cs
T scs
T hc s
E E CS
Th
Ts
E E DIO (a s INP UT )
Symbol
Tclk
Tch
Tcl
Tdv
Tod
Tscs
Thcs
Tlcs
Ts
Th
Description
EECK clock cycle time
EECK clock high time
EECK clock low time
EEDIO output valid to EECK rising edge time
EECK rising edge to EEDIO output delay time
EECS output valid to EECK rising edge time
EECK falling edge to EECS invalid time
Minimum EECS low time
EEDIO input setup time
EEDIO input hold time
Min
2560
2562
2560
7680
23039
20
0
29
Typ
5120
2560
2560
-
Max
-
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.4 MII Timing
Ttch
Ttcl
Ttcl k
TXCLK
Tts
Tth
TXEN / TXD[3:0]
Symbol
Ttclk
Ttch
Ttcl
Tts
Tth
Description
Min
23.0
7.0
TXCLK clock cycle time *1
TXCLK clock high time *2
TXCLK clock low time *2
TXD [3:0], TXEN setup to rising TXCLK
TXD [3:0], TXEN hold from rising TXCLK
Trch
Trcl
Typ
40.0
20.0
20.0
-
Max
-
Unit
ns
ns
ns
ns
ns
Max
-
Unit
ns
ns
ns
ns
ns
Trclk
RXCLK
Trs
Trh
RXDV / RXD[3:0]
Symbol
Trclk
Trch
Trcl
Trs
Trh
Description
Min
5.0
3.5
RXCLK clock cycle time *1
RXCLK clock high time *2
RXCLK clock low time *2
RXD [3:0], RXDV setup to rising RXCLK
RXD [3:0], RXDV hold from rising TXCLK
Typ
40.0
20.0
20.0
-
*1: For 10Mbps, the typical value of Ttclk and Trclk shall scale to 400ns.
*2: For 10Mbps, the typical value of Ttch, Ttcl, Trch, and Trcl shall scale to 200ns.
30
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.5 Station Management Timing
Tch
Tcl
Tclk
MDC
Tod
MDIO(asOUTPUT)
Ts
Th
MDIO(asINPUT)
MAC mode with MII: MDC=Output
Symbol
Description
Tclk MDC clock cycle time
Tch MDC clock high time
Tcl
MDC clock low time
Tod MDC clock rising edge to MDIO output delay
Ts
MDIO data input setup time
Th
MDIO data input hold time
Min
0.5
125
0
Typ
640
320
320
-
Max
-
Unit
ns
ns
ns
Tclk
ns
ns
PHY/Dual-PHY mode with Reverse-MII/RMII: MDC=Input
Symbol
Description
Min
Tclk MDC clock cycle time
Tch MDC clock high time
Tcl
MDC clock low time
Tod MDC clock rising edge to MDIO output delay
0
Ts
MDIO data input setup time
10
Th
MDIO data input hold time
10
Typ
320
160
160
-
Max
300
-
Unit
ns
ns
ns
ns
ns
ns
31
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.6 Reverse-MII Timing
Tch
Tcl
Tclk
RXCLK
Trs
Trh
RXD[3:0]
RXDV
Symbol
Tclk
Tch
Tcl
Trs
Trh
Description
Min
10.0
10.0
Clock cycle time
Clock high time
Clock low time
RXD [3:0], RXDV setup to rising RXCLK
RXD [3:0], RXDV hold from rising RXCLK
Tch
Tcl
Typ
40.0
20.0
20.0
-
Max
-
Unit
ns
ns
ns
ns
ns
Tclk
TXCLK
Tts
Tth
TXD[3:0]
TXEN
Symbol
Tts
Tth
Description
Min
11.0
2.0
TXD [3:0], TXEN setup to rising TXCLK
TXD [3:0], TXEN hold from rising TXCLK
32
Typ
-
Max
-
Unit
ns
ns
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.7 Reverse-RMII Timing
Tref_c l
Tref_ch
Tref_clk
REFCLK_I
Tref_rs
Tref_rh
RXD[1:0]
CRSDV
Symbol
Tref_clk
Tref_ch
Tref_cl
Tref_rs
Tref_rh
Description
Clock cycle time
Clock high time
Clock low time
RXD [1:0], CRSDV setup to rising REFCLK_I
RXD [1:0], CRSDV hold from rising REFCLK_I
Min
4.0
2.0
Typ
20.0
10.0
10.0
-
Max
-
Unit
ns
ns
ns
ns
ns
Max
-
Unit
ns
ns
Tref_c l
Tref_ch
Tref_clk
REFCLK_I
Tref_ts
Tref_th
TXD[1:0]
TXEN
Symbol
Tref_ts
Tref_th
Description
TXD [1:0], TXEN setup to rising REFCLK_I
TXD [1:0], TXEN hold from rising REFCLK_I
33
Min
4.0
2.0
Typ
-
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.8 I2C Interface Timing
I2C Master Controller Timing table:
Symbol
Parameter
Fclk
Thigh
Tlow
Tsu_sta
Thd_sta
I2C_SCL clock frequency.
High period of the I2C_SCL clock.
Low period of the I2C_SCL clock.
Setup time for a repeated START (Sr) condition.
Hold time of (repeated) START (S) condition. After
this period, the first clock pulse is generated
Tsu_dat Data Setup time.
Thd_dat Data Hold time.
Tsu_sto Data Setup time for STOP (P) condition.
Tbuf Bus free time between a STOP and START
condition.
Standard
mode (Typ)
100
4.0
6.0
4.0
4.0
Fast mode
(Typ)
400
1.0
1.5
1.0
1.0
2.0
4.0
4.0
0.5
1.0
1.0
Note 1
Unit
KHz
µs
µs
µs
µs
µs
µs
µs
Note 1: It will be much greater than 22us because several factors can influence this parameter such as USB system
utilization, the CBW structure, and High/Full speed, etc.
I2C Slave Controller Timing Table:
Symbol
Parameter
Fclk
I2C_SCL clock frequency.
Thigh
High period of the I2C_SCL clock in Fast mode.
High period of the I2C_SCL clock in Standard mode.
Tlow
Low period of the I2C_SCL clock.
Tsu_sta Setup time for a repeated START (Sr) condition.
Thd_sta Hold time of (repeated) START (S) condition. After
this period, the first clock pulse is generated
Tsu_dat Data Setup time.
Thd_dat Data Hold time.
Tsu_sto Data Setup time for STOP (P) condition.
Tbuf
Bus free time between a STOP and START condition.
Min
0.6
4.0
0.4
1
Typ
-
Max
390
-
3
-
-
3
0.4
1
-
-
-
Unit
KHz
µs
µs
µs
Tsys_clk
(Note 2)
Tsys_clk
Tsys_clk
µs
Tsys_clk
Note 2: Tsys_clk =33.33ns for 30MHz operating system clock.
34
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.9 SPI Interface Timing
Note: Above diagram only shows setup and hold time relationship of SPI pins in Mode 0. For the remaining 3 modes,
clock polarity is reversed.
SPI Master Controller Timing Table:
Symbol
Description
Fclk
SPI_SCLK clock frequency.
Min
-
Typ
Fsys_clk/
(SPIBRR+1)*2
Max
5
Unit
MHz
(Note 3)
Tl
Setup time of SPI_SS to the first SPI_SCLK edge.
-
0.5
-
Th
Tdly
Hold time of SPI_SS after the last SPI_SCLK edge.
SPI_MOSI data valid time after SPI_SCLK edge.
-
0.5
-
1
Dsu
Dhd
tl
SPI_MISO data setup time before SPI_SCLK edge.
SPI_MISO data hold time after SPI_SCLK edge.
Minimum idle time between transfers (minimum
SPI_SS high time).
Internal time base period.
2
4
-
-
Tclk
(Note 3)
Tclk
Tsys_clk
(Note 4)
Tsys_clk
Tsys_clk
-
Tclk
Note 5
-
0.5
Note 3: Fsys_clk is the operating system clock frequency 30Mhz. The SPIBRR is SPI Baud Rate Register.
Tclk = 1/Fclk.
Note 4: Tsys_clk =1/ Fsys_clk =33.33 ns.
Note 5: It will be much greater than 22us because several factors can influence this parameter, such as USB system
utilization, the CBW structure, and High/Full speed ,etc.
35
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
SPI Slave Controller Timing Table:
Symbol
Description
Fclk
SPI_SCLK clock frequency.
Tdly
SPI_MISO data valid time after SPI_SCLK edge.
Dsu
SPI_MOSI data setup time before SPI_SCLK edge.
Dhd
SPI_MOSI data hold time after SPI_SCLK edge.
SSsu
SPI_SS setup time before SPI_SCLK edge.
SShd
SPI_SS hold time after SPI_SCLK edge.
SSidle
SPI_SS negation to next SPI_SS active time
36
Min
1
3
2
4
2
Typ
-
Max
Unit
2
MHz
3
Tsys_clk
Tsys_clk
Tsys_clk
Tsys_clk
Tsys_clk
Tsys_clk
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.10 10/100M Ethernet PHY Interface Timing
+Vtxov
+Vtxa
Tr: from 10% to 90%
0V
10/100M Ethernet PHY Transmitter Waveform and Spec:
Symbol
Description
Condition
Peak-to-peak differential output voltage 10BASE-T mode
Vtxa *2 Peak-to-peak differential output voltage 100BASE-TX mode
Tr / Tf Signal rise / fall time
100BASE-TX mode
Output jitter
100BASE-TX mode, scrambled idle
signal
Vtxov Overshoot
100BASE-TX mode
Min
4.4
1.9
3
-
Typ Max Units
5
5.6
V
2
2.1
V
4
5
ns
1.4
ns
-
5
%
10/100M Ethernet PHY Receiver Spec:
Symbol
Description
Receiver input impedance
Differential squelch voltage
Common mode input voltage
Maximum error-free cable length
Condition
10BASE-T mode
37
Min
Typ Max
Units
10
300
2.97
100
400
3.3
-
KΩ
mV
V
meter
500
3.63
-
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
9.4.11 USB Transceiver Interface Timing
VCC33A_H/ VCC33A_PLL= 3.0 ~ 3.6 V.
Static Characteristic for Analog I/O Pins (DP/DM):
Symbol
Parameter
Conditions
Min
USB 2.0 Transceiver (HS)
Input Levels (Differential Receiver)
High
speed
differential
input
300
VHSDIFF
|VI (DP) –VI (DM)|
sensitivity
Measured at the connection as
Typ Max Unit
-
-
mV
-50
-
500
mV
-
-
100
mV
200
-
-
mV
-10
-
10
mV
-10
-
10
mV
-360
-
400
mV
700
-
1100
mV
-900
-
-500
mV
40.5
45
3.0
-
3.6
V
0.2
-
-
V
0.8
-
2.5
V
0.8
-
2.0
V
Low-level output voltage
0
-
0.3
V
High-level output voltage
2.8
-
3.6
V
an application circuit.
VHSCM
VHSSQ
VHSOI
VHSOL
VHSOH
VCHIRPJ
VCHIRPK
High speed data signaling
common mode voltage range
High speed squelch detection
threshold
Squelch detected
No squelch detected
Output levels (differential)
High speed idle level output
voltage
High speed low level output
voltage
High speed high level output
voltage
Chirp-J output voltage
Chirp-K output voltage
Resistance
Equivalent resistance used as
internal chip
Termination
RDRV
Driver output impedance
VTERM
Termination voltage for pull-up
resistor on pin RPU
USB 1.1 Transceiver (FS/LS)
Input Levels (Differential Receiver)
Differential input sensitivity
|VI (DP) –VI (DM)|
VDI
VCM
VSE
Differential common mode
voltage
Input Levels (Single-Ended Receiver)
Single ended receiver threshold
49.5 Ohm
Output levels
VOL
VOH
38
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
Dynamic Characteristic for Analog I/O Pins (DP/DM):
Symbol
Parameter
Conditions
Driver Characteristic
High-Speed Mode
High-speed
differential
rise
time
tHSR
tHSF
High-speed differential fall time Full-Speed Mode
CL=50pF; 10 to 90% of
tFR
Rise time of DP/DM
tFF
Fall time of DP/DM
CL=50pF; 90 to 10% of
Differential rise/fall time
Excluding the first transition
from idle mode
tFRMA
VCRS
Min
Typ
Max
Unit
500
-
-
ps
500
-
-
ps
4
-
20
ns
4
-
20
ns
90
-
110
%
1.3
-
2.0
V
|VOH - VOL|
|VOH - VOL|
matching (tFR / tFF)
Output signal crossover voltage Excluding the first transition
from idle mode
Driver Timing
High-Speed Mode
Driver waveform requirement
See eye pattern of template 1
VI, FSE 0, OE to DP, DN
Propagation delay
Data source jitter and receiver
jitter tolerance
tPLH(rcv)
tPHL (rcv)
Receiver propagation delay
(DP; DM to RCV)
tPLH(single)
tPHL(single)
Receiver propagation delay
(DP; DM to VOP, VON)
Follow template 1 described in USB
rev 2.0 spec.
(http://www.usb.org/developers/docs
)
Full-Speed Mode
For detailed description of VI,
15
ns
FSE 0 and OE, please refer to
USB rev 1.1specification.
Receiver Timing
High-Speed Mode
See eye pattern of template 4 Follow template 4 described in USB
rev 2.0 spec.
(http://www.usb.org/developers/docs
)
Full-Speed Mode
For detailed description of
15
ns
RCV, please refer to USB rev
(Note)
1.1specification.
15
ns
(Note)
Note: Full-Speed Timing diagram
39
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
10.0 Package Information
10.1 AX88772A 64-pin LQFP package
A
A2
A1
L
L1
D
Hd
He
E
pin 1
e
b
θ
Symbol
Millimeter
A1
Min
0.05
Typ
-
Max
0.15
A2
1.35
1.40
1.45
A
-
-
1.60
b
0.13
0.18
0.23
D
7.00
E
7.00
e
-
0.40
Hd
9.00
He
9.00
-
L
0.45
0.60
0.75
L1
-
1.00 REF
-
θ
0°
3.5°
7°
40
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
10.2 AX88172A 80-pin TQFP package
A
A2
A1
L
L1
D
Hd
He
E
pin 1
e
b
θ
Symbol
Millimeter
A1
Min
0.05
Typ
-
Max
0.15
A2
0.95
1.00
1.05
A
-
-
1.20
b
0.13
0.16
0.23
D
10.00
E
10.00
e
-
0.4 BSC
Hd
12.00
He
12.00
-
L
0.45
0.60
0.75
L1
-
1.00 REF
-
θ
0°
3.5°
7°
41
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
11.0 Ordering Information
Part Number
AX88772ALF
AX88172ATF
Description
AX88772A: Product Name (64 pin).
L: LQFP Package.
F: Lead Free.
AX88172A: Product Name (80 pin).
T: TQFP Package.
F: Lead Free.
42
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
12.0 Revision History
Revision
Date
Comment
V0.7
V1.0
2007/8/13
2007/11/21
V1.1
2007/12/24
Initial Release.
1. Update the power consumption information and add IDEVICE and
ISYSTEM in Section 9.2.
2. Move the Thermal Characteristics information from Section 9.2 to
Section 9.1.2 and update the Thermal Characteristics information.
3. Update the Tj junction operating temperature information in
Section 9.1.2, 9.1.4, 9.1.5 and 9.1.6.
4. Update the Reset Timing information in Section 9.4.2.
1. Update some information in Section 9.1.6.
43
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
APPENDIX A. Default WOL Ready Mode
Please contact ASIX for receiving “AX88x72A Full Datasheet” which contains detailed description of Appendix A.
44
ASIX ELECTRONICS CORPORATION
AX88772A/AX88172A
Low-pin-count
USB 2.0 to 10/100M Fast Ethernet Controller
4F, No.8, Hsin Ann Rd., Hsinchu Science Park,
Hsinchu, Taiwan, R.O.C.
TEL: +886-3-5799500
FAX: +886-3-5799558
Email: [email protected]
Web: http://www.asix.com.tw
45
ASIX ELECTRONICS CORPORATION
Similar pages