Meder DIL-CL-1A81-15-13M Line sensing Datasheet

DIL-CL Series
MEDER electronic
Line Sensing
Reed Relays
DESCRIPTION
The DIL-CL series is used for line sensing in many
modems, fax machines, private branch exchanges
(PBX) and other telecommunication devices. It is
superior to semiconductor solutions regarding
flashover and impulse strength. The DIL-CL series
is approved according to EN60950.
CHARACTERISTICS
FEATURES
• Line Sense Relay
• Breakdown voltage coil-contact up to 4.25
kVDC / 3.0 kVRMS
• Approved according to EN60950
• Low profile version only 5.8 mm high
• UL approval
• Pull-In current < 15 mA possible
DIMENSIONS
All dimensions in mm [inches]
ORDER INFORMATION
RELAY
CONTACT
SWITCH
SERIES
FORM
MODEL
DIL-CL -
1A
81 -
OPTIONS
Part Number Example
COIL
RESISTANCE
PIN OUT
(IN Ω)
XX -
XXX
9, 10, 15, 4/4*
13M, 15M,
18M, 513M**
DIL - CL - 1A81 - 9 - 13M
9 is the coil resistance in Ω
13M is the pin out
* Avai lable wi th pi n out 18M only.
** Avai lable only wi th 10 & 15 Ω coi l resi stance.
www.meder.com
264
Germany # ++49-(0)7733-94870, USA # 800-870-5385
MEDER electronic
DIL-CL Series
Line Sensing
Reed Relays
PIN OUT
tt
COIL DATA
CONTACT
FOR M
SWITCH
MODEL
PIN OUT
All data at 20 0C t
COIL
RESISTANCE
PULL-IN
CURRENT
DROP-OUT
CURRENT
INDUCTANCE
at 1 kHz at 1 COIL
(*at BOTH COILS)
Ω
mA
mA
mH
Nom.
Typ.
Max.
Min.
Max.
Min.
Max.
Min.
Typ.
Max.
9
10
11
5.1
15
5
14.9
1.6
2.0
2.4
14
15
17
5.1
15
5
14.9
2.88
3.6
4.32
13 M
15 M
8
9
10
5.1
15
5
14.9
2.56
3.2
3.92
13 M
14
15
17
5.1
15
5
14.9
3.52
4.4
5.28
18 M tt
3.6
4
4.4
5.1
15
5
14.9
0.64
2.56*
0.8
3.2*
0.96
3.84*
Height 5.8 mm
1A
81
513 M
Height 10.6 mm
1A
t
tt
81
The pull-in / drop-out current and coil resistance will change at the rate of 0.4% per 0C.
Values presented are for coils in series aiding.
www.meder.com
Germany # ++49-(0)7733-94870, USA # 800-870-5385
265
DIL-CL Series
MEDER electronic
Line Sensing
Reed Relays
RELAY DATA
All data at 20 0C
Switch Model -->
Contact For m -->
Contact Ratings
Conditions
Switch 81
For m A
Min.
Typ. Max. Units
Switching Power
Any DC combination of V & A not
to exceed their individual max.'s
5
W
Switching Voltage
D C or peak A C
90
V
Switching Current
D C or peak A C
0.5
A
Carry Current
D C or peak A C
1.0
A
Static Contact Resistance
w/ 0.5V & 50mA
200
mΩ
Dynamic Contact Resistance
Measured w/ 0.5V & 50mA 1.5 ms
after closure
200
mΩ
Insulation Resistance
(100 Volts applied)
Breakdown Voltage
Across contacts
Contact to coil
Across contacts
Contact to coil
109
1 0 10
100
4.25
3.0
Operate Time, incl. Bounce
Measured w/ 100% overdrive
0.5
ms
Release Time
Measured w/ no coil suppression
0.1
ms
Capacitance
Across contacts
Contact to coil
0.2
4.0
pF
DC only & <10 pF stray cap.
100
106
Cycles
Ω
VD C
kV D C
kVRMS
Life Expectancies
Switching 5 Volts@ 10mA
For other load requirements please see our life test section located
on page 151.
Environmental Data
Shock Resistance
1/2 sine wave duration 11ms
30
g
Vibration Resistance
From 10 - 2000 Hz
10
g
Ambient Temperature
10 0C/ minute max. allowable
-20
70
0
C
Storage Temperature
10 0C/ minute max. allowable
-25
85
0
C
Soldering Temperature
5 sec. dwell
260
0
C
www.meder.com
266
Germany # ++49-(0)7733-94870, USA # 800-870-5385
Similar pages