FTDI FTPD-1 Full-speed usb to uart converter Datasheet

FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
Future Technology
Devices International
Ltd
FTPD-1 FTDI Programmer
Debugger 1 Module
Datasheet
FTPD-1 is a module used for programming and debugging.
1. Introduction
1.1 Features
The FTPD-1 is a module with a FT230X USB to
UART converter and a dual buffer. The FTPD-1
utilises these components to generate a single
line half-duplex UART signal with no handshake
w hich can be used to program several of FTDI’s
MCU devices, predominantly FT51A.
The FTPD-1 has the following features:
This module also provides a switched 5V power
supply to the target device and is configured
such that it does not infringe USB compliance
regulations for supplying bus power.

FTPD-1’s board dimensions are the same as a
credit card; however the fitted components give
it additional height. The module is supplied with
a berg connector ribbon cable; however it is
compatible for operation with pogo pin cables.
All components used, including the FT230X are
Pb-free (RoHS compliant).
 Full-Speed USB to UART converter
 Single half-duplex UART data pin input/output
Two dedicated GPIOs to control Reset# and Prog#
outputs
 TXDEN line to control the direction of the halfduplex UART data
 PWREN# line to control the power supply
 2X3 way 2.54mm pitch shrouded male header
 150mm ribbon cable with Female to Female
2.54mm pitch 2x3 way connectors
 Protected by resettable fuse with 0.5A hold current
and schottky diode on the output power line.
 Pogo pin compatible
 Power output available, indication LED
N either the whole nor any part of the information c ontained in, or the produc t des c ribed in this manual, may be adapted or
reproduc ed in any material or elec tronic form without the prior written c ons ent of the c opyright holder. T his produc t and its
doc umentation are s upplied on an as - is basis and no warranty as to their s uitability for any partic ular purpose is either made
or implied. Future T echnology D evices I nternational L td will not ac c ept any c laim for damages hows oever aris ing as a res ult
of us e or failure of this produc t. Y our s tatutory rights are not affec ted. T his product or any variant of it is not intended for use
in any medic al applianc e, devic e or s ys tem in whic h the failure of the produc t might reas onably be expec ted to res ult in
pers onal injury. T his doc ument provides preliminary information that may be s ubject to c hange without notice. N o freedom to
us e patents or other intellectual property rights is implied by the public ation of this doc ument. Future T ec hnology D evic es
I nternational L td, U nit 1 , 2 Seaward P lace, C enturion Business P ark, G lasgow G 4 1 1 HH U nited Kingdom. Sc otland Regis tered
C ompany N umber: SC 1 3 6 6 4 0
Copyright © 2015 Future Technology Devices International Limited
1
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
Table of Contents
1. Introduction ................................................................. 1
1.1
Features ................................................................................ 1
2 Driver Support ................................................................ 3
3 Ordering Information ...................................................... 4
4 FTDP-1 Signals ............................................................... 5
4.1
FTPD-1 Pin Out ...................................................................... 5
4.2 Signal Descriptions ................................................................... 6
5 Module Dimensions......................................................... 7
6 FTPD-1 Module Circuit Schematic .................................... 8
7 Hardware Setup Guide .................................................... 9
7.1
Connecting to MCU board ....................................................... 9
7.2
Connecting to PC ...................................................................10
8 Contact Information ..................................................... 11
Appendix A – List of Figures and Tables............................ 12
List of Figures ...............................................................................12
List of Tables ................................................................................12
Appendix B – Revision History.......................................... 13
2
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
2 Driver Support
Royalty-Free Drivers (USB Drivers + DLL S/W Interface):

Windows 10 32,64-bit

Windows 8.1 32,64-bit

Windows 8 32,64-bit

Windows 7 32,64-bit
The drivers listed above are all available to download for free from www.ftdichip.com.
3
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
3 Ordering Information
Module Code
Description
FTPD-1
FTDI Programmer / Debugger Module
4
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
4 FTDP-1 Signals
4.1
FTPD-1 Pin Out
1 : NC
2 : VSW
3 : RESET#
4 : PROG#
5 : DBG
6 : GND
Figure 1 – Module Pin Out
Figure 1 illustrates the signals available on the 6 pin header of the FTPD-1.
5
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
4.2 Signal Descriptions
Pin No.
Name
Type
Description
C N2-1
NC
Not C onnected
Floating pin.
C N2-2
VSW
Power Out
C N2-3
RESET#
Signal Output
Active low reset output.
C N2-4
PROG#
Signal Output
Active low PROG# output..
C N2-5
DBG
Signal Input/output
Half-duplex UART data pin.
C N2-6
GND
Ground
0V Ground.
5 volt power output. Outputs power sources from the USB bus when
the FT230X has enumerated.
Table 1 - Module Pin Out Description
Pin No.
Name
Type
Description
C N1-1
VBUS
Power
5 volt power input.
C N1-2
DM
Signal Input/Output
USB Data - from upstream device
C N1-3
DP
Signal Input/Output
USB Data + from upstream device
C N1-4
GND
Ground
0 volt ground.
Table 2 - Upstream USB Port Pin Out Description
6
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
5 Module Dimensions
Figure 2 – FTPD-1 Module Dimensions
All dimensions are given in millimetres.
The FTPD-1 module exclusively uses lead free components, and is fully compliant with European Union
directive 2002/95/EC.
7
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
6 FTPD-1 Module Circuit Schematic
Figure 3 – Module Circuit Schematic
8
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
7 Hardware Setup Guide
The FTPD-1 is designed to be used with FTDI’s microcontroller chips for firmware programming and
debugging purposes. It allows direct connection with FT51A module s such as UMFT51A-EVM and
UMFT51AA, with the 6-way ribbon cable assembly provide d in the package.
7.1
Connecting to MCU board
Figure 4 - FTPD-1 connection to UMFT51A-EVM
9
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
Figure 5 - FTPD-1 connection to UMFT51AA-1
7.2
Connecting to PC
The FTPD-1 has a mini-USB connector for the host connection. The first time the FTPD-1 module is
connected to a Windows PC, the USB device drivers need to install. This should happen automatically if
the PC is connected to the internet. Alternatively users can download the D2XX driver from the FTDI
website and install the driver manually.
Successful installation will result in a new device appearing in the Device manager under universal Serial
Bus Controllers
Figure 6 - FTPD-1 successful driver installation
It is labelled “USB Serial Converter” – the text coming from the driver file.
10
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
8 Contact Information
Head Office – Glasgow, UK
Branch Office – Tigard, Oregon, USA
Unit 1, 2 Seaward Place, Centurion Business Park
Glasgow G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
7130 SW Fir Loop
Tigard, OR 97223
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
E-Mail (Sales)
E-Mail (Support)
E-Mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Branch Office – Taipei, Taiwan
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan , R.O.C.
Tel: +886 (0) 2 8797 1330
Fax: +886 (0) 2 8751 9737
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
Branch Office – Shanghai, China
Room 1103, No. 666 West Huaihai Road,
Shanghai, 200052
C hina
Tel: +86 (0)21 6235 1596
Fax: +86 (0)21 6235 1595
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Web Site
http://ftdichip.com
Distributor and Sales Representatives
Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales
representative(s) in your country.
Sys tem and equipment manufacturers and des igners are responsible to ens ure that their s ystems, and any Future T echnology D evi c es
I nternational L td (FTDI) devices incorporated in their s ys tems , meet all applic able s afety, regulatory and s ys tem- level performanc e
requirements. A ll application-related information in this doc ument (inc luding application descriptions, s uggested FTD I devices and other
materials ) is provided for referenc e only. While FT DI has taken c are to as s ure it is ac c urate, this information is s ubjec t to c us tomer
c onfirmation, and FT DI disclaims all liability for s ys tem des igns and for any applic ations as s is tanc e provided by FT D I . U s e o f FT D I
devic es in life s upport and/or s afety applic ations is entirely at the us er’s ris k, a nd the us er agrees to defend, indemnify and hold
harmles s FTDI from any and all damages , c laims, s uits or expense resulting from s uc h us e. T his document is s ubject to c hange without
notic e. N o freedom to us e patents or other intellectual property rights is implied by the public ation of this doc ument. N either the whole
nor any part of the information c ontained in, or the produc t des cribed in this document, may be adapted or reproduc ed in any material
or elec tronic form without the prior written c ons ent of th e c opyright holder. Future T ec hnology D evic es I nternational L td, U nit 1 , 2
Seaward P lac e, C enturion Busines s P ark, G las gow G 4 1 1 H H , U nited Kingdom. Sc otland Regis tered C ompany N umber: SC 1 3 6 6 4 0
11
C opyright © 2015 Future T echnology D evices I nternational L imited
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
Appendix A – List of Figures and Tables
List of Figures
Figure 1 – Module Pin Out ...................................................................................................................... 5
Figure 2 – FTPD-1 Module Dimensions .................................................................................................... 7
Figure 3 – Module Circuit Schematic ....................................................................................................... 8
Figure 4 - FTPD-1 connection to UMFT51A-EVM ...................................................................................... 9
Figure 5 - FTPD-1 connection to UMFT51AA-1 ....................................................................................... 10
Figure 6 - FTPD-1 successful driver installation ..................................................................................... 10
List of Tables
Table 1 - Module Pin Out Description ...................................................................................................... 6
Table 2 - Upstream USB Port Pin Out Description .................................................................................... 6
Copyright © 2015 Future Technology Devices International Limited
12
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Version 1.0
Document Ref erence No.: FT_001263
Clearance No.: FTDI# 480
Appendix B – Revision History
Document Title:
FTPD-1 FTDI Programmer Debugger 1 Module Datasheet
Document Reference No.:
FT_001263
Clearance No.:
FTDI# 480
Product Page:
http://www.ftdichip.com
Document Feedback:
Send Feedback
Revision
Version 1.0
Changes
Date
Initial Release
Copyright © 2015 Future Technology Devices International Limited
2015-12-07
13
Similar pages