Hittite HMC624LP4 0.5 db lsb gaas mmic 6-bit digital attenuator, dc - 6 ghz Datasheet

HMC624LP4 / 624LP4E
v09.0210
ATTENUATORS - DIGITAL - SMT
8
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Typical Applications
Features
The HMC624LP4(E) is ideal for:
0.5 dB LSB Steps to 31.5 dB
• Cellular/3G Infrastructure
Power-Up State Selection
• WiBro / WiMAX / 4G
High Input IP3: +55 dBm
• Microwave Radio & VSAT
Low Insertion Loss: 2.2 dB @ 3.5 GHz
• Test Equipment and Sensors
TTL/CMOS Compatible, Serial, Parallel
or Latched Parallel Control
• IF & RF Applications
±0.25 dB Typical Step Error
Single +3V or +5V Supply
24 Lead 4x4mm SMT Package: 16mm2
Functional Diagram
General Description
The HMC624LP4(E) is a broadband 6-bit GaAs IC
Digital Attenuator in a low cost leadless SMT package.
This versatile digital attenuator incorporates off-chip
AC ground capacitors for near DC operation, making
it suitable for a wide variety of RF and IF applications.
The dual mode control interface is CMOS/TTL
compatible, and accepts either a three wire serial
input or a 6 bit parallel word. The HMC624LP4(E) also
features a user selectable power up state and a serial
output port for cascading other Hittite serial controlled
components. The HMC624LP4(E) is housed in a
RoHS compliant 4x4 mm QFN leadless package, and
requires no external matching components.
Electrical Specifications,
TA = +25° C, 50 Ohm System, with Vdd = +5V & Vctl = 0/+5V (Unless Otherwise Noted)
Parameter
Insertion Loss
Frequency (GHz)
DC - 3 GHz
3.0 - 6.0 GHz
Attenuation Range
Typ.
Max.
Units
1.8
2.8
2.4
3.8
dB
dB
31.5
dB
DC - 6 GHz
15
dB
DC - 0.8 GHz
0.8 - 6.0 GHz
± (0.10 + 5% of Atten. Setting) Max.
± (0.30 + 3% of Atten. Setting) Max.
dB
dB
Input Power for 0.1 dB Compression
DC - 6 GHz
30
dBm
Input Third Order Intercept Point
(Two-Tone Input Power= 10 dBm Each Tone)
DC - 6 GHz
55
dBm
Return Loss (ATTIN, ATTOUT, All Atten. States)
Attenuation Accuracy: (Referenced to Insertion Loss)
All Attenuation States
8-1
Min.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Insertion Loss vs. Temperature
(Only Major States are Shown)
-1
-2
-3
+25 C
+85 C
-40 C
-4
-5
-5
8 dB
-10
16 dB
-15
-20
-25
31.5 dB
-30
-35
0
1
2
3
4
5
6
0
1
2
FREQUENCY (GHz)
Input Return Loss [1]
4
5
6
5
6
5
6
Output Return Loss [1]
(Only Major States are Shown)
(Only Major States are Shown)
0
0
-5
-5
-10
-10
-15
RETURN LOSS (dB)
RETURN LOSS (dB)
3
FREQUENCY (GHz)
IL
-20
-25
-30
16 dB
-35
-15
2 dB
-20
-25
31.5 dB
-30
1 dB
-35
31.5 dB
-40
8 dB
-40
0
1
2
3
4
5
6
ATTENUATORS - DIGITAL - SMT
0
NORMALIZED ATTENUATION (dB)
INSERTION LOSS (dB)
0
0
1
16 dB
2
FREQUENCY (GHz)
3
4
FREQUENCY (GHz)
Bit Error vs. Attenuation State
Bit Error vs. Frequency [2]
(Only Major States are Shown)
[2]
2
1
500MHz
0.8
1.5
4GHz
0.6
31.5 dB
1
0.4
BIT ERROR (dB)
BIT ERROR (dB)
8
Normalized Attenuation [1]
[1]
0.2
0
-0.2
-0.4
2GHz, 3GHz
-0.6
0.5
0
-0.5
-1
100MHz, 1GHz
-1.5
-0.8
-2
-1
0
4
8
12
16
20
24
28
32
ATTENUATION STATE (dB)
0
1
2
3
4
FREQUENCY (GHz)
[1] Data taken with bias tees on input and output RF ports.
[2] C1, C6 = 330pF
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-2
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
8
Worst Case Step Error
Between Successive Attenuation States [2]
IP3 vs. Temperature [2]
80
0.6
70
8 dB
0.4
0.2
IP3 (dBm)
STEP ERROR (dB)
ATTENUATORS - DIGITAL - SMT
1
0.8
0
-0.2
60
50
4 dB
-0.4
16 dB
-0.6
40
-0.8
-1
30
0
1
2
3
4
5
6
0
1
FREQUENCY (GHz)
2
3
4
5
6
FREQUENCY (GHz)
Serial Control Interface
The HMC624LP4E contains a 3-wire SPI compatible digital interface (SERIN, CLK, LE). The serial control interface
is activated when P/S is kept high. The 6-bit serial word must be loaded MSB first. The positive-edge sensitive CLK
and LE requires clean transitions. If mechanical switches are used, sufficient debouncing should be provided. When
LE is high, 6-bit data in the serial input register is transferred to the attenuator. When LE is high CLK is masked to
prevent data transition during output loading.
When P/S is low, 3-wire SPI interface inputs (SERIN, CLK, LE) are disabled and the input register is loaded with
parallel digital inputs (D0-D5). When LE is high, 6-bit parallel data changes the state of the part per truth table.
For all modes of operations, the state will stay constant while LE is kept low.
8-3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Parallel Mode
(Direct Parallel Mode & Latched Parallel Mode)
Parameter
Typ.
Min. serial period, tSCK
100 ns
Control set-up time, tCS
20 ns
Control hold-time, tCH
20 ns
LE setup-time, tLN
10 ns
Min. LE pulse width, tLEW
10 ns
Min LE pulse spacing, tLES
630 ns
Serial clock hold-time from LE, tCKN
10 ns
Hold Time, tPH.
0 ns
Latch Enable Minimum Width, tLEN
10 ns
Setup Time, tPS
2 ns
Note: The parallel mode is enabled when P/S is set to low.
Direct Parallel Mode - The attenuation state is changed by the control voltage inputs D0-D5 directly. The LE (Latch
Enable) must be at a logic high at all times to control the attenuator in this manner.
Latched Parallel Mode - The attenuation state is selected using the control voltage inputs D0-D5 and set while the
LE is in the Low state. The attenuator will not change state while LE is Low. Once all Control Voltage Inputs are at the
desired states the LE is pulsed. See timing diagram above for reference.
Power-Up States
PUP Truth Table
If LE is set to logic LOW at power-up, the logic state of
PUP1 and PUP2 determines the power-up state of the
part per PUP truth table. If the LE is set to logic HIGH
at power-up, the logic state of D0-D5 determines
the power-up state of the part per truth table. The
attenuator latches in the desired power-up state
approximately 200 ms after power-up.
Power-On Sequence
The ideal power-up sequence is: GND, Vdd, digital
inputs, RF inputs. The relative order of the digital
inputs are not important as long as they are powered
after Vdd / GND
Bias Voltage
LE
PUP1
PUP2
Relative Attenuation
0
0
0
-31.5
0
1
0
-24
0
0
1
-16
0
1
1
Insertion Loss
1
X
X
0 to -31.5 dB
Note: The logic state of D0 - D5 determines the
power-up state per truth table shown below when LE
is high at power-up.
Truth Table
Control Voltage Input
D5
D4
D3
D2
D1
D0
Reference
Insertion
Loss
High
High
High
High
High
High
0 dB
Idd (Typ.) (mA)
High
High
High
High
High
Low
-0.5 dB
3
1.8
High
High
High
High
Low
High
-1 dB
5
2.0
High
High
High
Low
High
High
-2 dB
High
High
Low
High
High
High
-4 dB
High
Low
High
High
High
High
-8 dB
Low
High
High
High
High
High
-16 dB
Low
Low
Low
Low
Low
Low
-31.5 dB
Vdd (V)
Control Voltage Table
State
Vdd = +3V
Vdd = +5V
Low
0 to 0.5V @ <1 µA
0 to 0.8V @ <1 µA
High
2 to 3V @ <1 µA
2 to 5V @ <1 µA
ATTENUATORS - DIGITAL - SMT
8
Timing Diagram (Latched Parallel Mode)
Any combination of the above states will provide an attenuation
equal to the sum of the bits selected.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-4
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
ATTENUATORS - DIGITAL - SMT
8
Absolute Maximum Ratings
RF Input Power (DC - 6 GHz)
28 dBm (T = +85 °C)
Digital Inputs (Reset, Shift Clock,
Latch Enable & Serial Input)
-0.5 to Vdd +0.5V
Bias Voltage (Vdd)
5.6V
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 9.8 mW/°C above 85 °C) [1]
0.635 W
Thermal Resistance
102 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC624LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC624LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H624
XXXX
H624
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
8-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Pin Number
Function
Description
1
P/S
2
CLK
3
SERIN
4
LE
5, 14
GND
These pins and package bottom
must be connected to RF/DC ground.
6, 13
ATTIN,
ATTOUT
These pins are DC coupled and matched to 50 Ohms.
Blocking capacitors are required. Select value based
on lowest frequency of operation.
7 - 12
ACG1 - ACG6
External capacitors to ground is required. Select value for
lowest frequency of operation. Place capacitor as close to
pins as possible.
15
SEROUT
Serial input data delayed by 6 clock cycles.
16, 17
PUP2, PUP1
19 - 24
D5, D4, D3,
D2, D1, D0
18
Vdd
Interface Schematic
See truth table, control voltage
table and timing diagram.
ATTENUATORS - DIGITAL - SMT
8
Pin Descriptions
See truth table, control voltage
table and timing diagram.
Supply voltage
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-6
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Application Circuit
ATTENUATORS - DIGITAL - SMT
8
8-7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC624LP4 / 624LP4E
v09.0210
0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
8
ATTENUATORS - DIGITAL - SMT
Evaluation PCB
List of Materials for Evaluation PCB 117212 [1]
Item
Description
J1, J2
PCB Mount SMA Connector
J3
18 Pin DC Connector
J8, J11
DC Pin
C1, C6
330 pF Capacitor, 0402 Pkg.
C7, C8
1000 pF Capacitor, 0402 Pkg.
R1 - R14
100 kOhm Resistor, 0402 Pkg.
SW1, SW2
SPDT 4 Position DIP Switch
U1
HMC624LP4(E) Digital Attenuator
PCB [2]
117210 Evaluation PCB
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 Ohm impedance while the package
ground leads and exposed paddle should be
connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25FR
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-8
Similar pages