IRC TT CHP1/8-100-2203-G-BLK-LF Metal glazeâ ¢ cylindrical surface mount power resistor Datasheet

Metal Glaze™ Cylindrical
Surface Mount
Power Resistors
Metal Glaze™ thick
film element fired
at 1000°C to solid
ceramic substrate
CHP Series
•
•
•
•
•
Up to 2 watts
Up to 1000 volts
0.2 ohm to 2.2 megohm range
RoHS-compliant version available
150°C maximum operating temperature
High
temperature
dielectric
coating
Solder over nickel
barrier
Electrical Data
Industry
Footprint
IRC
Type
CHP 1/8
1206
CHP 1/2
2010
CHP 1
Size
Code1
B&C
D&E
2512
CHP 2
3610
F
H
Maximum
Power Rating
1/4W @ 70°C
1/2W @ 70°C
1W @ 70°C
2W @ 25°C
1.33W @ 70°C
Working
Voltage²
200
300
350
500
Maximum
Voltage
Resistance
Range (ohms)³
Product
Category
Tolerance
(±%)³
TCR
(ppm/°C)³
0.1 to 0.99
Low Range
1, 2, 5
100
400
600
700
1.0 to 1.0 M
Standard
1, 2, 5
50, 100
20 to 348K
Tight Tolerance
0.25, 0.5
50, 100
0.1 to 0.99
Low Range
1, 2, 5
100
1.0 to 348K
Standard
1, 2, 5
50, 100
0.1 to 0.99
Low Range
1, 2, 5
100
1.0 to 2.21M
Standard
1, 2, 5
50, 100
20 to 348K
Tight Tolerance
0.25, 0.5
50, 100
0.2 to 0.99
Low Range
1, 2, 5
100
Standard
1, 2, 5
50, 100
1000
1.0 to 2.21M
¹See page 8 for product dimensions, recommended solder pads, and standard packaging.
²Not to exceed √P x R
³Consult factory for tighter TCR, tolerance, or resistance values.
Environmental Data
Characteristics
Maximum Change
Test Method
Temperature Coefficient
As specified
MIL-R-55342E Par 4.7.9 (-55°C + 125°C)
Thermal Shock
±0.5% + 0.01 ohm
MIL-R-55342E Par 4.7.3 (-65°C + 150°C, 5 cycles)
Low Temperature Operation
±0.25% + 0.01 ohm
MIL-R-55342E Par 4.7.4 (-65°C @ working voltage)
Short Time Overload
±0.5% + 0.01 ohm
±1% for R>100K ohm
MIL-R-55342E Par 4.7.5
2.5 x √
for 5 seconds
High Temperature Exposure
±0.5% + 0.01 ohm
MIL-R-55342E Par 4.7.6 (-150°C for 100 hours)
Resistance to Bonding
±0.25% + 0.01 ohm
MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260°C for 10 seconds)
Exposure
95% minimum coverage
MIL-STD-202, Method 208 (245°C for 5 seconds)
Solderability
±0.5% + 0.01 ohm
MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours)
Moisture Resistance
±0.5% + 0.01 ohm
MIL-R-55342E Par 4.7.10 (2000 hours at 70°C intermittent)
Life Test
Terminal Adhesion Strength
±1% + 0.01 ohm
no mechanical damage
1200 gram push from underside of mounted cchip for 60 seconds
±1% + 0.01 ohm
no mechanical damage
Chip mounted in center of 90mm long board, deflected 1mm so as to
exert pull on chip contacts for 5 seconds
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
CHP Series Issue July 2009 Sheet 1 of 3
Metal Glaze™ Cylindrical
Surface Mount
Power Resistors
Physical Data
L
C
W
IRC Type
Size Code
Dimensions (Inches and (mm))
Industry
Footprint
Actual Size
L
W
C
0.057 ± 0.006
(1.45 ± 0.15)
0.020 ± 0.010
(0.51 ± 0.25)
CHP 1/8
B
1206
0.128 ± 0.007
(3.25 ± 0.18)
MRC 1/2
C
1206
0.128 ± 0.007
(3.25 ± 0.18)
0.063 ± 0.010
(1.60 ± 0.25)
0.020 ± 0.010
(0.51 ± 0.25)
CHP 1/2
D
2010
0.200 ± 0.010
(5.08 ± 0.25)
0.079 ± 0.006
(2.01 ± 0.15)
0.030 ± 0.010
(0.761 ± 0.25)
MRC 1
E
2010
0.200 ± 0.010
(5.08 ± 0.25)
0.105 ± 0.006
(2.67 ± 0.15)
0.040 ± 0.015
(1.02 ± 0.38)
CHP 1
F
2512
0.251 ± 0.010
(6.38 ± 0.25)
0.079 ± 0.006
(2.01 ± 0.15)
0.040 ± 0.010
(1.02 ± 0.25)
CHP 2
H
3610
0.367 ± 0.010
(9.32 ± 0.25)
0.105 ± 0.006
(2.67 ± 0.15)
0.050 ± 0.010
(1.27 ± 0.25)
Recommended Solder Pad Dimensions (Reflow):
F
A
C
A
B
E
D
Size
Code
Industry
Footprint
Dimensions (Inches and mm))
A
B
C
D
E
F
0.093
(2.36)
0.058
(1.47)
0.098
(2.49)
0.032
(0.81)
0.211
(5.36)
B&C
1206
0.076
(1.93)
D
2010
0.111
(2.82)
0.126
(3.20)
0.096
(2.44)
0.152
(3.86)
0.040
(1.02)
0.318
(8.08)
E
2010
0.170
(4.32)
0.160
(4.06)
0.072
(1.83)
0.132
(3.35)
0.044
(1.12)
0.412
(10.46)
F
2512
0.121
(3.07)
0.126
(3.20)
0.127
(3.23)
0.183
(4.65)
0.040
(1.02)
0.369
(9.37)
H
3610
0.170
(4.32)
0.160
(4.06)
0.213
(5.41)
0.273
(6.93)
0.044
(1.12)
0.553
(14.05)
© IRC Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
CHP Series Issue July 2009 Sheet 2 of 3
Metal Glaze™ Cylindrical
Surface Mount
Power Resistors
Standard Reel Packaging per EIA-481:
IRC
Type
Size
Code
Industry
Footprint
CHP 1/8
MRC 1/2
B
C
1206
CHP 1/2
MRC 1
D
E
2010
CHP 1
F
2512
CHP 2
H
Reel
Diameter*
3610
Quantity
Per Reel
7″
2,500 max.
13″
10,000 max.
7″
1,500 max.
13″
5,000 max.
7″
1,500 max.
13″
5,000 max.
13″
1,500 max.
Carrier Tape
Width
Component
Pitch
8mm
4mm
12mm
4mm
12mm
4mm
24mm
4mm
*The 13″ reel is considered standard and will be supplied unless otherwise specified.
Repetitive Surge Curve
Power Derating Curve
100
1000
80
Peak Power (watts)
% of Rated Power
CHP 1/8, 1/2, 1
60
CHP 2
40
20
0
30
40
50 60
70
80
CHP 2
CHP 1
100
CHP 1/8
10
90 100 110 120 130 140 150
Ambient Temperature (°C)
1
0.0001
0.0010
0.0100
0.1000
1.0000
.1msec
1msec
10msec
100msec
10000msec
Surge or Pulse Duration (seconds)
Note: Use for repetitive pulses where the average power dissipation is
not to exceed the component rating at 70°C. Surge handling capacity
for low-repetitive surges may be significantly greater than shown above.
Contact factory for recommendations.
Ordering Data
Sample Part No.
CHP 1
- 100
2203
F
13
LF
IRC Type
(CHP 1/8, CHP 1/2, CHP 1, or CHP 2)
Temperature Coefficient
(50 ppm, 100 ppm)
Resistance Value
(100 ohms and greater - First 3 significant digits plus 4th digit multiplier)
Example: 100 ohms = 1000, 1000 ohms = 1001, 150,000 ohms = 1503
(Less than 100 ohms - "R" is used to designate decimal)
Example: 51 ohms = 51R0, 1 ohm = 1R00, 0.25 ohms = R250
Tolerance
(C = 0.25%, D = 0.5%, F = 1.0%; G = 2.0%; J = 5.0%)
Packaging Code*
(BLK = Bulk, 7 = 7" Reel, 13 = 13" Reel)
Lead Free Construction
© IRC Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
CHP Series Issue July 2009 Sheet 3 of 3
Similar pages