TOSHIBA TC74HC04AFN

TC74HC04AP/AF/AFN
TOSHIBA CMOS Digital Integrated Circuit
Silicon Monolithic
TC74HC04AP,TC74HC04AF,TC74HC04AFN
Hex Inverter
The TC74HC04A is a high speed CMOS INVERTER fabricated
with silicon gate C2MOS technology.
It achieves the high speed operation similar to equivalent
LSTTL while maintaining the CMOS low power dissipation.
The internal circuit is composed of 3 stages, including buffered
output, which provide high noise immunity and stable output.
All inputs are equipped with protection circuits against satic
discharge or transient excess voltage.
Note: xxxFN (JEDEC SOP) is not available in
Japan.
TC74HC04AP
Features
TC74HC04AF
•
High speed: tpd = 6 ns (typ.) at VCC = 5 V
•
Low power dissipation: ICC = 1 μA (max) at Ta = 25°C
•
High noise immunity: VNIH = VNIL = 28% VCC (min)
•
Output drive capability: 10 LSTTL loads
•
•
Symmetrical output impedance: |IOH| = IOL = 4 mA (min)
∼ tpHL
Balanced propagation delays: tpLH −
•
Wide operating voltage range: VCC (opr) = 2 to 6 V
•
Pin and function compatible with 74LS04
TC74HC04AFN
Pin Assignment
Weight
DIP14-P-300-2.54
SOP14-P-300-1.27A
SOL14-P-150-1.27
: 0.96 g (typ.)
: 0.18 g (typ.)
: 0.12 g (typ.)
IEC Logic Symbol
1
2007-10-01
TC74HC04AP/AF/AFN
Truth Table
A
Y
L
H
H
L
Absolute Maximum Ratings (Note 1)
Characteristics
Symbol
Rating
Unit
Supply voltage range
VCC
−0.5 to 7
V
DC input voltage
VIN
−0.5 to VCC + 0.5
V
DC output voltage
VOUT
−0.5 to VCC + 0.5
V
Input diode current
IIK
±20
mA
Output diode current
IOK
±20
mA
DC output current
IOUT
±25
mA
DC VCC/ground current
ICC
±50
mA
Power dissipation
PD
500 (DIP) (Note 2)/180 (SOP)
mW
Storage temperature
Tstg
−65 to 150
°C
Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or
even destruction.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 2: 500 mW in the range of Ta = −40 to 65°C. From Ta = 65 to 85°C a derating factor of −10 mW/°C shall be
applied until 300 mW.
Operating Ranges (Note)
Characteristics
Symbol
Rating
Unit
Supply voltage
VCC
2 to 6
V
Input voltage
VIN
0 to VCC
V
VOUT
0 to VCC
V
Topr
−40 to 85
°C
Output voltage
Operating temperature
0 to 1000 (VCC = 2.0 V)
Input rise and fall time
tr, tf
0 to 500 (VCC = 4.5 V)
ns
0 to 400 (VCC = 6.0 V)
Note:
The operating ranges must be maintained to ensure the normal operation of the device.
Unused inputs must be tied to either VCC or GND.
2
2007-10-01
TC74HC04AP/AF/AFN
Electrical Characteristics
DC Characteristics
Characteristics
High-level input
voltage
Low-level input
voltage
VCC (V)
Min
Typ.
Max
Min
Max
2.0
1.50
⎯
⎯
1.50
⎯
4.5
3.15
⎯
⎯
3.15
⎯
6.0
4.20
⎯
⎯
4.20
⎯
2.0
⎯
⎯
0.50
⎯
0.50
4.5
⎯
⎯
1.35
⎯
1.35
6.0
⎯
⎯
1.80
⎯
1.80
2.0
1.9
2.0
⎯
1.9
⎯
4.5
4.4
4.5
⎯
4.4
⎯
6.0
5.9
6.0
⎯
5.9
⎯
IOH = −4 mA
4.5
4.18
4.31
⎯
4.13
⎯
IOH = −5.2 mA
6.0
5.68
5.80
⎯
5.63
⎯
2.0
⎯
0.0
0.1
⎯
0.1
4.5
⎯
0.0
0.1
⎯
0.1
6.0
⎯
0.0
0.1
⎯
0.1
IOL = 4 mA
4.5
⎯
0.17
0.26
⎯
0.33
IOL = 5.2 mA
6.0
⎯
0.18
0.26
⎯
0.33
⎯
VIH
⎯
VIL
IOH = −20 μA
High-level output
voltage
VOH
VIN
= VIH or VIL
IOL = 20 μA
Low-level output
voltage
VOL
Ta =
−40 to 85°C
Ta = 25°C
Test Condition
Symbol
VIN
= VIH or VIL
Unit
V
V
V
V
Input leakage
current
IIN
VIN = VCC or GND
6.0
⎯
⎯
±0.1
⎯
±1.0
μA
Quiescent supply
current
ICC
VIN = VCC or GND
6.0
⎯
⎯
1.0
⎯
10.0
μA
Test Condition
Min
Typ.
Max
Unit
⎯
⎯
4
8
ns
⎯
⎯
6
12
ns
AC Characteristics (CL = 15 pF, VCC = 5 V, Ta = 25°C, input: tr = tf = 6 ns)
Characteristics
Output transition time
Propagation delay time
Symbol
tTLH
tTHL
tpLH
tpHL
3
2007-10-01
TC74HC04AP/AF/AFN
AC Characteristics (CL = 50 pF, input: tr = tf = 6 ns)
Characteristics
Output transition time
Propagation delay
time
Symbol
tTLH
tTHL
tpLH
tpHL
Input capacitance
CIN
Power dissipation
capacitance
CPD
Note:
(Note)
Ta =
−40 to 85°C
Ta = 25°C
Test Condition
Unit
VCC (V)
Min
Typ.
Max
Min
Max
2.0
⎯
30
75
⎯
95
4.5
⎯
8
15
⎯
19
6.0
⎯
7
13
⎯
16
2.0
⎯
27
75
⎯
95
4.5
⎯
9
15
⎯
19
6.0
⎯
8
13
⎯
16
⎯
⎯
5
10
⎯
10
pF
⎯
⎯
20
⎯
⎯
⎯
pF
⎯
⎯
ns
ns
CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating
current consumption without load.
Average operating current can be obtained by the equation:
ICC (opr) = CPD・VCC・fIN + ICC/6 (per gate)
4
2007-10-01
TC74HC04AP/AF/AFN
Package Dimensions
Weight: 0.96 g (typ.)
5
2007-10-01
TC74HC04AP/AF/AFN
Package Dimensions
Weight: 0.18 g (typ.)
6
2007-10-01
TC74HC04AP/AF/AFN
Package Dimensions (Note)
Note: This package is not available in Japan.
Weight: 0.12 g (typ.)
7
2007-10-01
TC74HC04AP/AF/AFN
RESTRICTIONS ON PRODUCT USE
20070701-EN GENERAL
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
8
2007-10-01