ON LB1935FA-AH Stepping motor driver ic Datasheet

Ordering number : ENA2060
LB1935FA
Monolithic Digital IC
Stepping Motor Driver IC
http://onsemi.com
Overview
LB1935FA is IC with forward/reverse motor drive 2-channel in which low saturation voltage and low voltage
operation possible. Its small sized package is optimal for 2 phase excitation drive of 2 phase bipolar stepping motors
for various portable devices such as digital still cameras.
Features
• Low saturation voltage, VO (sat) = 0.3V typ at IO = 150mA
• Built-in shoot-through current protection circuit
• No standby current consumption (or zero)
• Built-in thermal shutdown circuit
• Micro10 small-sized package
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Maximum power source voltage
VCC max
Applied output voltage
VOUT max
OUT1, OUT2, OUT3, OUT4 pin
Applied input voltage
VIN max
ENA, IN1, IN2 pin
GND Pin outflow current
I GND
Per channel
Allowable power dissipation
Pd max
With substrate*
Operating temperature
Topr
-20 to +75
°C
Storage temperature
Tstg
-40 to +150
°C
-0.3 to +8.0
V
VCC+VSF
V
-0.3 to +8.0
V
400
mA
400
mW
* Specified substrate: 20.0mm×10.0mm×0.8mm, paper phenol
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high
current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Semiconductor Components Industries, LLC, 2013
June, 2013
52312 SY 20120514-S00001 No.A2060-1/4
LB1935FA
Allowable Operating Range at Ta = 25°C
Parameter
Symbol
Source voltage
VCC
Input high level voltage
VIH
Input low level voltage
VIL
Conditions
Ratings
Unit
2.2 to 7.5
V
ENA, IN1, IN2 pin
1.8 to 7.5
V
ENA, IN1, IN2 pin
-0.3 to +0.7
V
Electric Characteristics at Ta = 25°C, VCC = 3.3V
Parameter
Symbol
Ratings
Conditions
min
Power source current
Output saturation voltage
Input current
Unit
typ
max
1
μA
13
19
mA
0.2
0.3
V
0.4
0.6
V
VIN = 3V
40
60
μA
VENA = 3V
40
60
μA
1
μA
1.7
V
ICC0
ENA = 0V, VIN = 3V or 0V
ICC1
ENA = 3V, VIN = 3V or 0V
VOUT1
ENA = 3V, VIN = 3V or 0V, IOUT = 100mA
VOUT2
ENA = 3V, VIN = 3V or 0V, IOUT = 200mA
IIN
IENA
0.1
Spark killer diode
Reverse current
IS(leak)
Forward voltage
VSF
IOUT = 200mA
Package Dimensions
unit : mm (typ)
3428
3.0
Pd max -- Ta
Allowable power dissipation, Pd max -- mW
500
0.55
4.9
3.0
10
1 2
0.5
0.16
1.03
0.25
Specified Substrate : 20.0×10.0×0.8mm3
Peper phenol
400
300
240
200
100
0
-20
0
20
40
60
80
100
0.1
Ambient temperature, Ta -- °C
SANYO : Micro10
Pin Assignments
VCC
1
10 OUT4
IN2
2
9
OUT3
ENA
3
8
OUT1
IN1
4
7
OUT2
(NC)
5
6
GND
LB1935FA
Top view
No.A2060-2/4
LB1935FA
Block Diagram
Truth Table
Input
ENA
IN1
Output
IN2
OUT1
OUT2
OUT3
OUT4
Remarks
L
-
-
OFF
OFF
OFF
OFF
Standby
H
L
L
H
L
H
L
2-phase excitation
L
H
H
L
L
H
H
H
L
H
L
H
H
L
L
H
H
L
No.A2060-3/4
LB1935FA
Timing Chart
Timing chart below shows the 2 phase excitation stepping motor.
ENA
IN1
IN2
OUT1
OUT2
OUT3
OUT4
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A2060-4/4
Similar pages