Document 287 -1 Shielded Power Inductors – MOS6020 • 6.0 × 7.1 mm footprint; 2.4 mm high shielded inductors • Custom versions up to 4.7 mH are available. Designer’s Kit C359 contains 3 of each value Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant matte tin over nickel over phos bronze. Other terminations available at additional cost. Weight 0.21 g Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 500 per 7″ reel; 2000 per 13″ reel; Plastic tape: 16 mm wide, 0.3 mm thick, 12 mm pocket spacing, 2.5 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Part number1 MOS6020-222ML_ MOS6020-332ML_ MOS6020-472ML_ MOS6020-682ML_ MOS6020-822ML_ MOS6020-103ML_ MOS6020-153ML_ MOS6020-223ML_ MOS6020-333ML_ MOS6020-473ML_ MOS6020-683ML_ MOS6020-104ML_ MOS6020-154ML_ MOS6020-224ML_ MOS6020-334ML_ MOS6020-474ML_ Inductance2 ±20% (µH) 2.2 3.3 4.7 6.8 8.2 10 15 22 33 47 68 100 150 220 330 470 DCR max SRF typ3 (Ohms) (MHz) 0.035 110 0.046 85 0.050 60 0.078 55 0.085 45 0.092 36 0.130 30 0.182 22 0.290 20 0.420 16 0.520 15 0.800 13 1.28 10 2.00 8 2.84 7 4.40 5 1. When ordering, please specify termination and packaging codes: MOS6020-104MLC Termination: L = RoHS compliant matte tin over nickel over phos bronze. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (500 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2000 parts per full reel). 10% drop 2.86 1.90 1.46 1.32 0.94 0.79 0.83 0.79 0.57 0.45 0.37 0.35 0.26 0.22 0.18 0.15 2 Isat (A)4 20% drop 3.26 2.28 1.82 1.56 1.18 0.95 0.95 0.92 0.67 0.56 0.45 0.40 0.30 0.26 0.22 0.17 Irms (A)5 20°C rise 40°C rise 3.0 4.1 2.6 3.6 2.3 3.1 1.9 2.7 1.7 2.3 1.6 2.2 1.3 1.8 1.0 1.4 0.80 1.1 0.50 0.7 0.45 0.63 0.40 0.56 0.35 0.49 0.30 0.42 0.25 0.35 0.22 0.29 30% drop 3.56 2.46 1.94 1.72 1.30 1.06 1.03 0.97 0.74 0.62 0.51 0.44 0.33 0.28 0.24 0.19 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/ HP 4263B LCR meter or equivalent. 3. SRF measured using Agilent/HP 8753D network analyzer. 4. DC current at 25°C that causes the specified inductance drop from its value without current. Click for temperature derating information. 5. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 6. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 287-1 Revised 09/02/15 Document 287-2 Shielded Power Inductors – MOS6020 Typical L vs Frequency Typical L vs Current 10000 10000 1000 470 µH Inductance (µH) Inductance (µH) 1000 100 µH 100 10 µH 10 2.2 µH 470 µH 100 100 µH 10 10 µH 2.2 µH 1 1 0.1 0.01 1 0.1 10 Frequency (MHz) 0.268 max 6,8 0.1 1 10 Current (A) 0.095 max 2,4 XXX 0.24 max 6,0 0.1 0.24 max 6,0 0.031 typ 0,80 0.169 typ 4,3 0.225 5,71 0.100 2,54 0.063 typ 1,60 0.055 1,39 Dimensions are in inches mm Recommended Land Pattern Document 287-2 Revised 09/02/15