AD ADSP-BF527KBCZ-5 Blackfin embedded processor Datasheet

Blackfin
Embedded Processor
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
FEATURES
PERIPHERALS
Up to 600 MHz high performance Blackfin processor
Two 16-bit MACs, two 40-bit ALUs, four 8-bit video ALUs,
40-bit shifter
RISC-like register and instruction model for ease of
programming and compiler-friendly support
Advanced debug, trace, and performance monitoring
Accepts a wide range of supply voltages for internal and I/O
operations. See Specifications on Page 28
Programmable on-chip voltage regulator (ADSP-BF523/
ADSP-BF525/ADSP-BF527 processors only)
Qualified for Automotive Applications. See Automotive
Products on Page 87
289-ball and 208-ball CSP_BGA packages
USB 2.0 high speed on-the-go (OTG) with integrated PHY
IEEE 802.3-compliant 10/100 Ethernet MAC
Parallel peripheral interface (PPI), supporting ITU-R 656
video data formats
Host DMA port (HOSTDP)
2 dual-channel, full-duplex synchronous serial ports
(SPORTs), supporting eight stereo I2S channels
12 peripheral DMAs, 2 mastered by the Ethernet MAC
2 memory-to-memory DMAs with external request lines
Event handler with 54 interrupt inputs
Serial peripheral interface (SPI) compatible port
2 UARTs with IrDA support
2-wire interface (TWI) controller
Eight 32-bit timers/counters with PWM support
32-bit up/down counter with rotary support
Real-time clock (RTC) and watchdog timer
32-bit core timer
48 general-purpose I/Os (GPIOs), with programmable
hysteresis
NAND flash controller (NFC)
Debug/JTAG interface
On-chip PLL capable of frequency multiplication
MEMORY
132K bytes of on-chip memory (See Table 1 on Page 3 for L1
and L3 memory size details)
External memory controller with glueless support for SDRAM
and asynchronous 8-bit and 16-bit memories
Flexible booting options from external flash, SPI, and TWI
memory or from host devices including SPI, TWI, and UART
Code security with Lockbox Secure Technology
one-time-programmable (OTP) memory
Memory management unit providing memory protection
WATCHDOG TIMER
OTP MEMORY
RTC
VOLTAGE REGULATOR*
JTAG TEST AND EMULATION
EAB
COUNTER
SPORT0
SPORT1
B
L1 INSTRUCTION
MEMORY
PERIPHERAL
ACCESS BUS
INTERRUPT
CONTROLLER
UART1
GPIO
PORT F
UART0
L1 DATA
MEMORY
16
DMA
CONTROLLER
DCB
USB
NFC
DMA
ACCESS
BUS
PPI
SPI
TIMER7-1
DEB
TIMER0
BOOT
ROM
EXTERNAL PORT
FLASH, SDRAM CONTROL
GPIO
PORT G
GPIO
PORT H
EMAC
HOST DMA
*REGULATOR ONLY AVAILABLE ON ADSP-BF523/ADSP-BF525/ADSP-BF527 PROCESSORS
TWI
PORT J
Figure 1. Processor Block Diagram
Blackfin and the Blackfin logo are registered trademarks of Analog Devices, Inc.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 U.S.A.
Tel: 781.329.4700
©2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
TABLE OF CONTENTS
Features ................................................................. 1
Clock Signals ...................................................... 16
Memory ................................................................ 1
Booting Modes ................................................... 18
Peripherals ............................................................. 1
Instruction Set Description .................................... 20
General Description ................................................. 3
Development Tools .............................................. 20
Portable Low Power Architecture ............................. 3
Additional Information ........................................ 21
System Integration ................................................ 3
Related Signal Chains ........................................... 22
Processor Peripherals ............................................. 3
Lockbox Secure Technology Disclaimer .................... 22
Blackfin Processor Core .......................................... 4
Signal Descriptions ................................................. 23
Memory Architecture ............................................ 5
Specifications ........................................................ 28
DMA Controllers .................................................. 9
Operating Conditions
for ADSP-BF522/ADSP-BF524/ADSP-BF526
Processors ...................................................... 28
Host DMA Port .................................................... 9
Real-Time Clock ................................................... 9
Watchdog Timer ................................................ 10
Operating Conditions for ADSP-BF523/ADSP-BF525/
ADSP-BF527 Processors .................................... 30
Timers ............................................................. 10
Electrical Characteristics ....................................... 32
Up/Down Counter and Thumbwheel Interface .......... 10
Absolute Maximum Ratings ................................... 37
Serial Ports ........................................................ 10
Package Information ............................................ 38
Serial Peripheral Interface (SPI) Port ....................... 11
ESD Sensitivity ................................................... 38
UART Ports ...................................................... 11
Timing Specifications ........................................... 39
TWI Controller Interface ...................................... 12
Output Drive Currents ......................................... 73
10/100 Ethernet MAC .......................................... 12
Test Conditions .................................................. 75
Ports ................................................................ 12
Environmental Conditions .................................... 79
Parallel Peripheral Interface (PPI) ........................... 13
289-Ball CSP_BGA Ball Assignment ........................... 80
USB On-The-Go Dual-Role Device Controller ........... 14
208-Ball CSP_BGA Ball Assignment ........................... 83
Code Security with Lockbox Secure Technology ......... 14
Outline Dimensions ................................................ 86
Dynamic Power Management ................................ 14
Surface-Mount Design .......................................... 87
ADSP-BF523/ADSP-BF525/ADSP-BF527
Voltage Regulation ........................................... 16
Automotive Products .............................................. 87
ADSP-BF522/ADSP-BF524/ADSP-BF526
Voltage Regulation ........................................... 16
Ordering Guide ..................................................... 88
REVISION HISTORY
7/13—Rev. C to Rev. D
Updated Development Tools .................................... 20
Corrected footnote 9 and added footnote 11 in
Operating Conditions for ADSP-BF523/ADSP-BF525/
ADSP-BF527 Processors .......................................... 30
Rev. D | Page 2 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
GENERAL DESCRIPTION
The ADSP-BF52x processors are members of the Blackfin family of products, incorporating the Analog Devices/Intel Micro
Signal Architecture (MSA). Blackfin® processors combine a
dual-MAC state-of-the-art signal processing engine, the advantages of a clean, orthogonal RISC-like microprocessor
instruction set, and single-instruction, multiple-data (SIMD)
multimedia capabilities into a single instruction-set
architecture.
The ADSP-BF52x processors are completely code compatible
with other Blackfin processors. The ADSP-BF523/
ADSP-BF525/ADSP-BF527 processors offer performance up to
600 MHz. The ADSP-BF522/ADSP-BF524/ADSP-BF526 processors offer performance up to 400 MHz and reduced static
power consumption. Differences with respect to peripheral
combinations are shown in Table 1.
Table 1. Processor Comparison
Memory (bytes)
1
PORTABLE LOW POWER ARCHITECTURE
Blackfin processors provide world-class power management
and performance. They are produced with a low power and low
voltage design methodology and feature on-chip dynamic
power management, which is the ability to vary both the voltage
and frequency of operation to significantly lower overall power
consumption. This capability can result in a substantial reduction in power consumption, compared with just varying the
frequency of operation. This allows longer battery life for
portable appliances.
ADSP-BF527
ADSP-BF525
ADSP-BF523
ADSP-BF526
ADSP-BF524
SYSTEM INTEGRATION
ADSP-BF522
Feature
Host DMA
USB
Ethernet MAC
Internal Voltage Regulator
TWI
SPORTs
UARTs
SPI
GP Timers
GP Counter
Watchdog Timers
RTC
Parallel Peripheral Interface
GPIOs
L1 Instruction SRAM
L1 Instruction SRAM/Cache
L1 Data SRAM
L1 Data SRAM/Cache
L1 Scratchpad
L3 Boot ROM
Maximum Instruction Rate1
Maximum System Clock Speed
Package Options
By integrating a rich set of industry-leading system peripherals
and memory, Blackfin processors are the platform of choice for
next-generation applications that require RISC-like programmability, multimedia support, and leading-edge signal
processing in one integrated package.
1
1
1
1
1
1
–
1
1
–
1
1
–
–
1
–
–
1
–
–
–
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
8
8
8
8
8
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
48 48 48 48 48 48
48K 48K 48K 48K 48K 48K
16K 16K 16K 16K 16K 16K
32K 32K 32K 32K 32K 32K
32K 32K 32K 32K 32K 32K
4K 4K 4K 4K 4K 4K
32K 32K 32K 32K 32K 32K
400 MHz
600 MHz
100 MHz
133 MHz
289-Ball CSP_BGA
208-Ball CSP_BGA
Maximum instruction rate is not available with every possible SCLK selection.
The ADSP-BF52x processors are highly integrated system-on-achip solutions for the next generation of embedded network
connected applications. By combining industry-standard interfaces with a high performance signal processing core, costeffective applications can be developed quickly, without the
need for costly external components. The system peripherals
include an IEEE-compliant 802.3 10/100 Ethernet MAC, a USB
2.0 high speed OTG controller, a TWI controller, a NAND flash
controller, two UART ports, an SPI port, two serial ports
(SPORTs), eight general purpose 32-bit timers with PWM capability, a core timer, a real-time clock, a watchdog timer, a Host
DMA (HOSTDP) interface, and a parallel peripheral interface
(PPI).
PROCESSOR PERIPHERALS
The ADSP-BF52x processors contain a rich set of peripherals
connected to the core via several high bandwidth buses, providing flexibility in system configuration as well as excellent overall
system performance (see the block diagram on Page 1).
These Blackfin processors contain dedicated network communication modules and high speed serial and parallel ports, an
interrupt controller for flexible management of interrupts from
the on-chip peripherals or external sources, and power management control functions to tailor the performance and power
characteristics of the processor and system to many application
scenarios.
All of the peripherals, except for the general-purpose I/O, TWI,
real-time clock, and timers, are supported by a flexible DMA
structure. There are also separate memory DMA channels dedicated to data transfers between the processor's various memory
spaces, including external SDRAM and asynchronous memory.
Multiple on-chip buses running at up to 133 MHz provide
enough bandwidth to keep the processor core running along
with activity on all of the on-chip and external peripherals.
The ADSP-BF523/ADSP-BF525/ADSP-BF527 processors
include an on-chip voltage regulator in support of the processor’s dynamic power management capability. The voltage
Rev. D | Page 3 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
BLACKFIN PROCESSOR CORE
The compute register file contains eight 32-bit registers. When
performing compute operations on 16-bit operand data, the
register file operates as 16 independent 16-bit registers. All
operands for compute operations come from the multiported
register file and instruction constant fields.
As shown in Figure 2, the Blackfin processor core contains two
16-bit multipliers, two 40-bit accumulators, two 40-bit ALUs,
four video ALUs, and a 40-bit shifter. The computation units
process 8-, 16-, or 32-bit data from the register file.
Each MAC can perform a 16-bit by 16-bit multiply in each
cycle, accumulating the results into the 40-bit accumulators.
Signed and unsigned formats, rounding, and saturation
are supported.
regulator provides a range of core voltage levels when supplied
from VDDEXT. The voltage regulator can be bypassed at the user's
discretion.
ADDRESS ARITHMETIC UNIT
L3
B3
M3
I2
L2
B2
M2
I1
L1
B1
M1
I0
L0
B0
M0
P5
DAG1
P4
P3
DAG0
P2
32
32
P1
P0
TO MEMORY
DA1
DA0
SP
FP
I3
32
32
PREG
RAB
SD
LD1
LD0
32
32
32
ASTAT
32
32
R7.H
R6.H
R7.L
R6.L
R5.H
R5.L
R4.H
R4.L
R3.H
R3.L
R2.H
R2.L
R1.H
R1.L
R0.H
R0.L
SEQUENCER
16
8
8
8
16
ALIGN
8
DECODE
BARREL
SHIFTER
40
40
A0
32
40
40
A1
LOOP BUFFER
CONTROL
UNIT
32
DATA ARITHMETIC UNIT
Figure 2. Blackfin Processor Core
The ALUs perform a traditional set of arithmetic and logical
operations on 16-bit or 32-bit data. In addition, many special
instructions are included to accelerate various signal processing
tasks. These include bit operations such as field extract and population count, modulo 232 multiply, divide primitives, saturation
and rounding, and sign/exponent detection. The set of video
instructions include byte alignment and packing operations,
16-bit and 8-bit adds with clipping, 8-bit average operations,
and 8-bit subtract/absolute value/accumulate (SAA) operations.
Also provided are the compare/select and vector search
instructions.
The 40-bit shifter can perform shifts and rotates and is used to
support normalization, field extract, and field deposit
instructions.
For certain instructions, two 16-bit ALU operations can be performed simultaneously on register pairs (a 16-bit high half and
16-bit low half of a compute register). If the second ALU is used,
quad 16-bit operations are possible.
The address arithmetic unit provides two addresses for simultaneous dual fetches from memory. It contains a multiported
register file consisting of four sets of 32-bit index, modify,
The program sequencer controls the flow of instruction execution, including instruction alignment and decoding. For
program flow control, the sequencer supports PC relative and
indirect conditional jumps (with static branch prediction), and
subroutine calls. Hardware is provided to support zero-overhead looping. The architecture is fully interlocked, meaning that
the programmer need not manage the pipeline when executing
instructions with data dependencies.
Rev. D | Page 4 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
In addition, multiple L1 memory blocks are provided, offering a
configurable mix of SRAM and cache. The memory management unit (MMU) provides memory protection for individual
tasks that may be operating on the core and can protect system
registers from unintended access.
The architecture provides three modes of operation: user mode,
supervisor mode, and emulation mode. User mode has
restricted access to certain system resources, thus providing a
protected software environment, while supervisor mode has
unrestricted access to the system and core resources.
The Blackfin processor instruction set has been optimized so
that 16-bit opcodes represent the most frequently used instructions, resulting in excellent compiled code density. Complex
DSP instructions are encoded into 32-bit opcodes, representing
fully featured multifunction instructions. Blackfin processors
support a limited multi-issue capability, where a 32-bit instruction can be issued in parallel with two 16-bit instructions,
allowing the programmer to use many of the core resources in a
single instruction cycle.
The Blackfin processor assembly language uses an algebraic syntax for ease of coding and readability. The architecture has been
optimized for use in conjunction with the C/C++ compiler,
resulting in fast and efficient software implementations.
MEMORY ARCHITECTURE
The Blackfin processor views memory as a single unified
4G byte address space, using 32-bit addresses. All resources,
including internal memory, external memory, and I/O control
registers, occupy separate sections of this common address
space. The memory portions of this address space are arranged
in a hierarchical structure to provide a good cost/performance
balance of some very fast, low-latency on-chip memory as cache
or SRAM, and larger, lower-cost and performance off-chip
memory systems. See Figure 3.
The on-chip L1 memory system is the highest-performance
memory available to the Blackfin processor. The off-chip
memory system, accessed through the external bus interface
unit (EBIU), provides expansion with SDRAM, flash memory,
and SRAM, optionally accessing up to 132M bytes of
physical memory.
The memory DMA controller provides high-bandwidth datamovement capability. It can perform block transfers of code
or data between the internal memory and the external
memory spaces.
CORE MMR REGISTERS (2M BYTES)
0xFFE0 0000
SYSTEM MMR REGISTERS (2M BYTES)
0xFFC0 0000
RESERVED
0xFFB0 1000
SCRATCHPAD SRAM (4K BYTES)
0xFFB0 0000
RESERVED
0xFFA1 4000
INSTRUCTION SRAM / CACHE (16K BYTES)
0xFFA1 0000
RESERVED
0xFFA0 C000
INSTRUCTION BANK B SRAM (16K BYTES)
0xFFA0 8000
INSTRUCTION BANK A SRAM (32K BYTES)
0xFFA0 0000
RESERVED
0xFF90 8000
DATA BANK B SRAM / CACHE (16K BYTES)
0xFF90 4000
DATA BANK B SRAM (16K BYTES)
INTERNAL MEMORY MAP
Blackfin processors support a modified Harvard architecture in
combination with a hierarchical memory structure. Level 1 (L1)
memories are those that typically operate at the full processor
speed with little or no latency. At the L1 level, the instruction
memory holds instructions only. The two data memories hold
data, and a dedicated scratchpad data memory stores stack and
local variable information.
0xFFFF FFFF
0xFF90 0000
RESERVED
0xFF80 8000
DATA BANK A SRAM / CACHE (16K BYTES)
0xFF80 4000
DATA BANK A SRAM (16K BYTES)
0xFF80 0000
RESERVED
0xEF00 8000
BOOT ROM (32K BYTES)
0xEF00 0000
RESERVED
0x2040 0000
ASYNC MEMORY BANK 3 (1M BYTES)
0x2030 0000
ASYNC MEMORY BANK 2 (1M BYTES)
0x2020 0000
ASYNC MEMORY BANK 1 (1M BYTES)
0x2010 0000
ASYNC MEMORY BANK 0 (1M BYTES)
0x2000 0000
RESERVED
0x08 00 0000
SDRAM MEMORY (16M BYTES
EXTERNAL MEMORY MAP
length, and base registers (for circular buffering), and eight
additional 32-bit pointer registers (for C-style indexed stack
manipulation).
128M BYTES)
0x0000 0000
Figure 3. Internal/External Memory Map
Internal (On-Chip) Memory
The processor has three blocks of on-chip memory providing
high-bandwidth access to the core.
The first block is the L1 instruction memory, consisting of
64K bytes SRAM, of which 16K bytes can be configured as a
four-way set-associative cache. This memory is accessed at full
processor speed.
The second on-chip memory block is the L1 data memory, consisting of up to two banks of up to 32K bytes each. Each memory
bank is configurable, offering both cache and SRAM functionality. This memory block is accessed at full processor speed.
The third memory block is a 4K byte scratchpad SRAM which
runs at the same speed as the L1 memories, but is only accessible
as data SRAM and cannot be configured as cache memory.
External (Off-Chip) Memory
External memory is accessed via the EBIU. This 16-bit interface
provides a glueless connection to a bank of synchronous DRAM
(SDRAM), as well as up to four banks of asynchronous memory
devices including flash, EPROM, ROM, SRAM, and memory
mapped I/O devices.
Rev. D | Page 5 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
The SDRAM controller can be programmed to interface to up
to 128M bytes of SDRAM. A separate row can be open for each
SDRAM internal bank and the SDRAM controller supports up
to 4 internal SDRAM banks, improving overall performance.
The asynchronous memory controller can be programmed to
control up to four banks of devices with very flexible timing
requirements for a wide variety of devices. Each bank occupies a
1M byte segment regardless of the size of the devices used, so
that these banks are only contiguous if each is fully populated
with 1M byte of memory.
NAND Flash Controller (NFC)
The ADSP-BF52x processors provide a NAND flash controller
(NFC). NAND flash devices provide high-density, low-cost
memory. However, NAND flash devices also have long random
access times, invalid blocks, and lower reliability over device
lifetimes. Because of this, NAND flash is often used for readonly code storage. In this case, all DSP code can be stored in
NAND flash and then transferred to a faster memory (such as
SDRAM or SRAM) before execution. Another common use of
NAND flash is for storage of multimedia files or other large data
segments. In this case, a software file system may be used to
manage reading and writing of the NAND flash device. The file
system selects memory segments for storage with the goal of
avoiding bad blocks and equally distributing memory accesses
across all address locations. Hardware features of the NFC
include:
• Support for page program, page read, and block erase of
NAND flash devices, with accesses aligned to page
boundaries.
• Error checking and correction (ECC) hardware that facilitates error detection and correction.
• A single 8-bit external bus interface for commands,
addresses, and data.
• Support for SLC (single level cell) NAND flash devices
unlimited in size, with page sizes of 256 and 512 bytes.
Larger page sizes can be supported in software.
• Capability of releasing external bus interface pins during
long accesses.
• Support for internal bus requests of 16 bits.
• DMA engine to transfer data between internal memory and
NAND flash device.
One-Time Programmable Memory
The processor has 64K bits of one-time programmable nonvolatile memory that can be programmed by the developer only
one time. It includes the array and logic to support read access
and programming. Additionally, its pages can be write
protected.
OTP enables developers to store both public and private data
on-chip. In addition to storing public and private key data for
applications requiring security, it also allows developers to store
completely user-definable data such as customer ID, product
ID, MAC address, etc. Hence, generic parts can be shipped,
which are then programmed and protected by the developer
within this non-volatile memory.
I/O Memory Space
The processor does not define a separate I/O space. All
resources are mapped through the flat 32-bit address space.
On-chip I/O devices have their control registers mapped into
memory-mapped registers (MMRs) at addresses near the top of
the 4G byte address space. These are separated into two smaller
blocks, one which contains the control MMRs for all core functions, and the other which contains the registers needed for
setup and control of the on-chip peripherals outside of the core.
The MMRs are accessible only in supervisor mode and appear
as reserved space to on-chip peripherals.
Booting
The processor contains a small on-chip boot kernel, which configures the appropriate peripheral for booting. If the processor is
configured to boot from boot ROM memory space, the processor starts executing from the on-chip boot ROM. For more
information, see Booting Modes on Page 18.
Event Handling
The event controller on the processor handles all asynchronous
and synchronous events to the processor. The processor provides event handling that supports both nesting and
prioritization. Nesting allows multiple event service routines to
be active simultaneously. Prioritization ensures that servicing of
a higher-priority event takes precedence over servicing of a
lower-priority event. The controller provides support for five
different types of events:
• Emulation — An emulation event causes the processor to
enter emulation mode, allowing command and control of
the processor via the JTAG interface.
• RESET — This event resets the processor.
• Nonmaskable Interrupt (NMI) — The NMI event can be
generated by the software watchdog timer or by the NMI
input signal to the processor. The NMI event is frequently
used as a power-down indicator to initiate an orderly shutdown of the system.
• Exceptions — Events that occur synchronously to program
flow (in other words, the exception is taken before the
instruction is allowed to complete). Conditions such as
data alignment violations and undefined instructions cause
exceptions.
• Interrupts — Events that occur asynchronously to program
flow. They are caused by input signals, timers, and other
peripherals, as well as by an explicit software instruction.
Each event type has an associated register to hold the return
address and an associated return-from-event instruction. When
an event is triggered, the state of the processor is saved on the
supervisor stack.
The processor event controller consists of two stages, the core
event controller (CEC) and the system interrupt controller
(SIC). The core event controller works with the system interrupt
Rev. D | Page 6 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
controller to prioritize and control all system events. Conceptually, interrupts from the peripherals enter into the SIC and are
then routed directly into the general-purpose interrupts of the
CEC.
Core Event Controller (CEC)
The CEC supports nine general-purpose interrupts (IVG15–7),
in addition to the dedicated interrupt and exception events. Of
these general-purpose interrupts, the two lowest-priority
interrupts (IVG15–14) are recommended to be reserved for
software interrupt handlers, leaving seven prioritized interrupt
inputs to support the peripherals of the processor. Table 2
describes the inputs to the CEC, identifies their names in the
event vector table (EVT), and lists their priorities.
System Interrupt Controller (SIC)
The system interrupt controller provides the mapping and routing of events from the many peripheral interrupt sources to the
prioritized general-purpose interrupt inputs of the CEC.
Although the processor provides a default mapping, the user
can alter the mappings and priorities of interrupt events by writing the appropriate values into the interrupt assignment
registers (SIC_IARx). Table 3 describes the inputs into the SIC
and the default mappings into the CEC.
Table 2. Core Event Controller (CEC)
Priority
(0 is Highest)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Event Class
Emulation/Test Control
RESET
Nonmaskable Interrupt
Exception
Reserved
Hardware Error
Core Timer
General-Purpose Interrupt 7
General-Purpose Interrupt 8
General-Purpose Interrupt 9
General-Purpose Interrupt 10
General-Purpose Interrupt 11
General-Purpose Interrupt 12
General-Purpose Interrupt 13
General-Purpose Interrupt 14
General-Purpose Interrupt 15
EVT Entry
EMU
RST
NMI
EVX
—
IVHW
IVTMR
IVG7
IVG8
IVG9
IVG10
IVG11
IVG12
IVG13
IVG14
IVG15
Table 3. System Interrupt Controller (SIC)
Peripheral Interrupt Event
PLL Wakeup Interrupt
DMA Error 0 (generic)
DMAR0 Block Interrupt
DMAR1 Block Interrupt
DMAR0 Overflow Error
DMAR1 Overflow Error
PPI Error
MAC Status
SPORT0 Status
SPORT1 Status
Reserved
Reserved
UART0 Status
UART1 Status
RTC
DMA Channel 0 (PPI/NFC)
DMA Channel 3 (SPORT0 RX)
DMA Channel 4 (SPORT0 TX)
DMA Channel 5 (SPORT1 RX)
DMA Channel 6 (SPORT1 TX)
TWI
DMA Channel 7 (SPI)
DMA Channel 8 (UART0 RX)
DMA Channel 9 (UART0 TX)
DMA Channel 10 (UART1 RX)
DMA Channel 11 (UART1 TX)
General Purpose
Interrupt (at RESET)
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG8
IVG8
IVG9
IVG9
IVG9
IVG9
IVG10
IVG10
IVG10
IVG10
IVG10
IVG10
Peripheral Interrupt ID
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Rev. D | Page 7 of 88 | July 2013
Default
Core Interrupt ID
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
2
2
2
2
3
3
3
3
3
3
SIC Registers
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR0 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR1 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR2 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 3. System Interrupt Controller (SIC) (Continued)
Peripheral Interrupt Event
OTP Memory Interrupt
GP Counter
DMA Channel 1 (MAC RX/HOSTDP)
Port H Interrupt A
DMA Channel 2 (MAC TX/NFC)
Port H Interrupt B
Timer 0
Timer 1
Timer 2
Timer 3
Timer 4
Timer 5
Timer 6
Timer 7
Port G Interrupt A
Port G Interrupt B
MDMA Stream 0
MDMA Stream 1
Software Watchdog Timer
Port F Interrupt A
Port F Interrupt B
SPI Status
NFC Status
HOSTDP Status
Host Read Done
Reserved
USB_INT0 Interrupt
USB_INT1 Interrupt
USB_INT2 Interrupt
USB_DMAINT Interrupt
General Purpose
Interrupt (at RESET)
IVG11
IVG11
IVG11
IVG11
IVG11
IVG11
IVG12
IVG12
IVG12
IVG12
IVG12
IVG12
IVG12
IVG12
IVG12
IVG12
IVG13
IVG13
IVG13
IVG13
IVG13
IVG7
IVG7
IVG7
IVG7
IVG10
IVG10
IVG10
IVG10
IVG10
Peripheral Interrupt ID
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Default
Core Interrupt ID
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
0
0
0
0
3
3
3
3
3
SIC Registers
IAR3 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
IAR3 IMASK0, ISR0, IWR0
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR4 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR5 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
IAR6 IMASK1, ISR1, IWR1
Event Control
The processor provides a very flexible mechanism to control the
processing of events. In the CEC, three registers are used to
coordinate and control events. Each register is 16 bits wide.
• CEC interrupt latch register (ILAT) — Indicates when
events have been latched. The appropriate bit is set when
the processor has latched the event and cleared when the
event has been accepted into the system. This register is
updated automatically by the controller, but it may be written only when its corresponding IMASK bit is cleared.
• CEC interrupt mask register (IMASK) — Controls the
masking and unmasking of individual events. When a bit is
set in the IMASK register, that event is unmasked and is
processed by the CEC when asserted. A cleared bit in the
IMASK register masks the event, preventing the processor
from servicing the event even though the event may be
latched in the ILAT register. This register may be read or
written while in supervisor mode. (Note that generalpurpose interrupts can be globally enabled and disabled
with the STI and CLI instructions, respectively.)
• CEC interrupt pending register (IPEND) — The IPEND
register keeps track of all nested events. A set bit in the
IPEND register indicates the event is currently active or
nested at some level. This register is updated automatically
by the controller but may be read while in supervisor mode.
The SIC allows further control of event processing by providing
three pairs of 32-bit interrupt control and status registers. Each
register contains a bit corresponding to each of the peripheral
interrupt events shown in Table 3 on Page 7.
• SIC interrupt mask registers (SIC_IMASKx) — Control the
masking and unmasking of each peripheral interrupt event.
When a bit is set in these registers, that peripheral event is
Rev. D | Page 8 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
unmasked and is processed by the system when asserted. A
cleared bit in the register masks the peripheral event, preventing the processor from servicing the event.
Examples of DMA types supported by the processor DMA controller include:
• A single, linear buffer that stops upon completion.
• SIC interrupt status registers (SIC_ISRx) — As multiple
peripherals can be mapped to a single event, these registers
allow the software to determine which peripheral event
source triggered the interrupt. A set bit indicates the
peripheral is asserting the interrupt, and a cleared bit indicates the peripheral is not asserting the event.
• A circular, auto-refreshing buffer that interrupts on each
full or fractionally full buffer.
• SIC interrupt wakeup enable registers (SIC_IWRx) — By
enabling the corresponding bit in these registers, a peripheral can be configured to wake up the processor, should the
core be idled or in sleep mode when the event is generated.
For more information see Dynamic Power Management on
Page 14.
In addition to the dedicated peripheral DMA channels, there are
two memory DMA channels provided for transfers between the
various memories of the processor system. This enables transfers of blocks of data between any of the memories—including
external SDRAM, ROM, SRAM, and flash memory—with minimal processor intervention. Memory DMA transfers can be
controlled by a very flexible descriptor-based methodology or
by a standard register-based autobuffer mechanism.
Because multiple interrupt sources can map to a single generalpurpose interrupt, multiple pulse assertions can occur simultaneously, before or during interrupt processing for an interrupt
event already detected on this interrupt input. The IPEND
register contents are monitored by the SIC as the interrupt
acknowledgement.
The appropriate ILAT register bit is set when an interrupt rising
edge is detected (detection requires two core clock cycles). The
bit is cleared when the respective IPEND register bit is set. The
IPEND bit indicates that the event has entered into the processor pipeline. At this point the CEC recognizes and queues the
next rising edge event on the corresponding event input. The
minimum latency from the rising edge transition of the generalpurpose interrupt to the IPEND output asserted is three core
clock cycles; however, the latency can be much higher, depending on the activity within and the state of the processor.
DMA CONTROLLERS
The processor has multiple, independent DMA channels that
support automated data transfers with minimal overhead for
the processor core. DMA transfers can occur between the
processor's internal memories and any of its DMA-capable
peripherals. Additionally, DMA transfers can be accomplished
between any of the DMA-capable peripherals and external
devices connected to the external memory interfaces, including
the SDRAM controller and the asynchronous memory controller. DMA-capable peripherals include the Ethernet MAC, NFC,
HOSTDP, USB, SPORTs, SPI port, UARTs, and PPI. Each individual DMA-capable peripheral has at least one dedicated DMA
channel.
The processor DMA controller supports both one-dimensional
(1-D) and two-dimensional (2-D) DMA transfers. DMA transfer initialization can be implemented from registers or from sets
of parameters called descriptor blocks.
The 2-D DMA capability supports arbitrary row and column
sizes up to 64K elements by 64K elements, and arbitrary row
and column step sizes up to ±32K elements. Furthermore, the
column step size can be less than the row step size, allowing
implementation of interleaved data streams. This feature is
especially useful in video applications where data can be deinterleaved on the fly.
• 1-D or 2-D DMA using a linked list of descriptors.
• 2-D DMA using an array of descriptors, specifying only the
base DMA address within a common page.
The processor also has an external DMA controller capability
via dual external DMA request pins when used in conjunction
with the external bus interface unit (EBIU). This functionality
can be used when a high speed interface is required for external
FIFOs and high bandwidth communications peripherals such as
USB 2.0. It allows control of the number of data transfers for
memory DMA. The number of transfers per edge is programmable. This feature can be programmed to allow memory
DMA to have an increased priority on the external bus relative
to the core.
HOST DMA PORT
The host port interface allows an external host to be a DMA
master to transfer data in and out of the device. The host device
masters the transactions and the Blackfin processor is the
DMA slave.
The host port is enabled through the PAB interface. Once
enabled, the DMA is controlled by the external host, which can
then program the DMA to send/receive data to any valid internal or external memory location.
The host port interface controller has the following features.
• Allows external master to configure DMA read/write data
transfers and read port status.
• Uses asynchronous memory protocol for external interface.
• 8-/16-bit external data interface to host device.
• Half duplex operation.
• Little-/big-endian data transfer.
• Acknowledge mode allows flow control on host
transactions.
• Interrupt mode guarantees a burst of FIFO depth host
transactions.
REAL-TIME CLOCK
The real-time clock (RTC) provides a robust set of digital watch
features, including current time, stopwatch, and alarm. The
RTC is clocked by a 32.768 kHz crystal external to the Blackfin
processor. Connect RTC pins RTXI and RTXO with external
Rev. D | Page 9 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
unknown state where software, which would normally reset the
timer, has stopped running due to an external noise condition
or software error.
components as shown in Figure 4.
RTXO
RTXI
If configured to generate a hardware reset, the watchdog timer
resets both the core and the processor peripherals. After a reset,
software can determine if the watchdog was the source of the
hardware reset by interrogating a status bit in the watchdog
timer control register.
R1
X1
C1
C2
The timer is clocked by the system clock (SCLK), at a maximum
frequency of fSCLK.
TIMERS
SUGGESTED COMPONENTS:
X1 = ECLIPTEK EC38J (THROUGH-HOLE PACKAGE) OR
EPSON MC405 12 pF LOAD (SURFACE-MOUNT PACKAGE)
C1 = 22 pF
C2 = 22 pF
R1 = 10 M:
There are nine general-purpose programmable timer units in
the processors. Eight timers have an external pin that can be
configured either as a pulse width modulator (PWM) or timer
output, as an input to clock the timer, or as a mechanism for
measuring pulse widths and periods of external events. These
timers can be synchronized to an external clock input to the several other associated PF pins, an external clock input to the
PPI_CLK input pin, or to the internal SCLK.
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
CONTACT CRYSTAL MANUFACTURER FOR DETAILS. C1 AND C2
SPECIFICATIONS ASSUME BOARD TRACE CAPACITANCE OF 3 pF.
Figure 4. External Components for RTC
The RTC peripheral has dedicated power supply pins so that it
can remain powered up and clocked even when the rest of the
processor is in a low power state. The RTC provides several programmable interrupt options, including interrupt per second,
minute, hour, or day clock ticks, interrupt on programmable
stopwatch countdown, or interrupt at a programmed alarm
time.
The 32.768 kHz input clock frequency is divided down to a 1 Hz
signal by a prescaler. The counter function of the timer consists
of four counters: a 60-second counter, a 60-minute counter, a
24-hour counter, and an 32,768-day counter.
When enabled, the alarm function generates an interrupt when
the output of the timer matches the programmed value in the
alarm control register. There are two alarms: The first alarm is
for a time of day. The second alarm is for a day and time of
that day.
The stopwatch function counts down from a programmed
value, with one-second resolution. When the stopwatch is
enabled and the counter underflows, an interrupt is generated.
Like the other peripherals, the RTC can wake up the processor
from sleep mode upon generation of any RTC wake-up event.
Additionally, an RTC wakeup event can wake up the processor
from deep sleep mode or cause a transition from the hibernate
state.
WATCHDOG TIMER
The processor includes a 32-bit timer that can be used to implement a software watchdog function. A software watchdog can
improve system availability by forcing the processor to a known
state through generation of a hardware reset, nonmaskable
interrupt (NMI), or general-purpose interrupt, if the timer
expires before being reset by software. The programmer initializes the count value of the timer, enables the appropriate
interrupt, then enables the timer. Thereafter, the software must
reload the counter before it counts to zero from the programmed value. This protects the system from remaining in an
Rev. D
|
The timer units can be used in conjunction with the two UARTs
to measure the width of the pulses in the data stream to provide
a software auto-baud detect function for the respective serial
channels.
The timers can generate interrupts to the processor core providing periodic events for synchronization, either to the system
clock or to a count of external signals.
In addition to the eight general-purpose programmable timers,
a ninth timer is also provided. This extra timer is clocked by the
internal processor clock and is typically used as a system tick
clock for generation of operating system periodic interrupts.
UP/DOWN COUNTER AND THUMBWHEEL
INTERFACE
A 32-bit up/down counter is provided that can sense 2-bit
quadrature or binary codes as typically emitted by industrial
drives or manual thumb wheels. The counter can also operate in
general-purpose up/down count modes. Then, count direction
is either controlled by a level-sensitive input pin or by two edge
detectors.
A third input can provide flexible zero marker support and can
alternatively be used to input the push-button signal of thumb
wheels. All three pins have a programmable debouncing circuit.
An internal signal forwarded to the timer unit enables one timer
to measure the intervals between count events. Boundary registers enable auto-zero operation or simple system warning by
interrupts when programmable count values are exceeded.
SERIAL PORTS
The processors incorporate two dual-channel synchronous
serial ports (SPORT0 and SPORT1) for serial and multiprocessor communications. The SPORTs support the following
features:
• I2S capable operation.
Page 10 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
• Bidirectional operation — Each SPORT has two sets of
independent transmit and receive pins, enabling eight
channels of I2S stereo audio.
The SPI port’s clock rate is calculated as:
• Buffered (8-deep) transmit and receive ports — Each port
has a data register for transferring data words to and from
other processor components and shift registers for shifting
data in and out of the data registers.
f SCLK
SPI Clock Rate = ----------------------------------2  SPI_BAUD
Where the 16-bit SPI_BAUD register contains a value of 2
to 65,535.
• Clocking — Each transmit and receive port can either use
an external serial clock or generate its own, in frequencies
ranging from (fSCLK/131,070) Hz to (fSCLK/2) Hz.
During transfers, the SPI port simultaneously transmits and
receives by serially shifting data in and out on its two serial data
lines. The serial clock line synchronizes the shifting and sampling of data on the two serial data lines.
• Word length – Each SPORT supports serial data words
from 3 to 32 bits in length, transferred most-significant-bit
first or least-significant-bit first.
UART PORTS
• Framing — Each transmit and receive port can run with or
without frame sync signals for each data word. Frame sync
signals can be generated internally or externally, active high
or low, and with either of two pulse widths and early or late
frame sync.
• Companding in hardware — Each SPORT can perform
A-law or μ-law companding according to ITU recommendation G.711. Companding can be selected on the transmit
and/or receive channel of the SPORT without
additional latencies.
• DMA operations with single-cycle overhead — Each
SPORT can automatically receive and transmit multiple
buffers of memory data. The processor can link or chain
sequences of DMA transfers between a SPORT and
memory.
• Interrupts — Each transmit and receive port generates an
interrupt upon completing the transfer of a data word or
after transferring an entire data buffer, or buffers,
through DMA.
• Multichannel capability — Each SPORT supports 128
channels out of a 1024-channel window and is compatible
with the H.100, H.110, MVIP-90, and HMVIP standards.
• PIO (programmed I/O) — The processor sends or receives
data by writing or reading I/O mapped UART registers.
The data is double-buffered on both transmit and receive.
• DMA (direct memory access) — The DMA controller
transfers both transmit and receive data. This reduces the
number and frequency of interrupts required to transfer
data to and from memory. The UART has two dedicated
DMA channels, one for transmit and one for receive. These
DMA channels have lower default priority than most DMA
channels because of their relatively low service rates.
Each UART port's baud rate, serial data format, error code generation and status, and interrupts are programmable:
• Supporting bit rates ranging from (fSCLK/1,048,576) to
(fSCLK/16) bits per second.
• Supporting data formats from seven to 12 bits per frame.
• Both transmit and receive operations can be configured to
generate maskable interrupts to the processor.
SERIAL PERIPHERAL INTERFACE (SPI) PORT
The processors have an SPI-compatible port that enables the
processor to communicate with multiple SPI-compatible
devices.
The UART port’s clock rate is calculated as:
The SPI interface uses three pins for transferring data: two data
pins (Master Output-Slave Input, MOSI, and Master InputSlave Output, MISO) and a clock pin (serial clock, SCK). An SPI
chip select input pin (SPISS) lets other SPI devices select the
processor, and seven SPI chip select output pins (SPISEL7–1) let
the processor select other SPI devices. The SPI select pins are
reconfigured general-purpose I/O pins. Using these pins, the
SPI port provides a full-duplex, synchronous serial interface,
which supports both master/slave modes and multimaster
environments.
The SPI port’s baud rate and clock phase/polarities are programmable, and it has an integrated DMA channel,
configurable to support transmit or receive data streams. The
SPI’s DMA channel can only service unidirectional accesses at
any given time.
Rev. D |
The processors provide two full-duplex universal asynchronous
receiver/transmitter (UART) ports, which are fully compatible
with PC-standard UARTs. Each UART port provides a simplified UART interface to other peripherals or hosts, supporting
full-duplex, DMA-supported, asynchronous transfers of serial
data. A UART port includes support for five to eight data bits,
one or two stop bits, and none, even, or odd parity. Each UART
port supports two modes of operation:
f SCLK
UART Clock Rate = ---------------------------------------------16  UART_Divisor
Where the 16-bit UART_Divisor comes from the UART_DLH
(most significant 8 bits) and UART_DLL (least significant
8 bits) registers.
In conjunction with the general-purpose timer functions, autobaud detection is supported.
The capabilities of the UARTs are further extended with support for the infrared data association (IrDA®) serial infrared
physical layer link specification (SIR) protocol.
Page 11 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
TWI CONTROLLER INTERFACE
The processors include a 2-wire interface (TWI) module for
providing a simple exchange method of control data between
multiple devices. The TWI is compatible with the widely used
I2C® bus standard. The TWI module offers the capabilities of
simultaneous master and slave operation and support for both
7-bit addressing and multimedia data arbitration. The TWI
interface utilizes two pins for transferring clock (SCL) and data
(SDA) and supports the protocol at speeds up to 400k bits/sec.
The TWI interface pins are compatible with 5 V logic levels.
Additionally, the TWI module is fully compatible with serial
camera control bus (SCCB) functionality for easier control of
various CMOS camera sensor devices.
• Convenient frame alignment modes support even 32-bit
alignment of encapsulated Rx or Tx IP packet data in memory after the 14-byte MAC header.
• Programmable Ethernet event interrupt supports any combination of:
• Any selected Rx or Tx frame status conditions.
• PHY interrupt condition.
• Wake-up frame detected.
• Any selected MAC management counter(s) at halffull.
• DMA descriptor error.
10/100 ETHERNET MAC
The ADSP-BF526 and ADSP-BF527 processors offer the capability to directly connect to a network by way of an embedded
Fast Ethernet Media Access Controller (MAC) that supports
both 10-BaseT (10M bits/sec) and 100-BaseT (100M bits/sec)
operation. The 10/100 Ethernet MAC peripheral on the processor is fully compliant to the IEEE 802.3-2002 standard and it
provides programmable features designed to minimize supervision, bus use, or message processing by the rest of the processor
system.
Some standard features are:
• 47 MAC management statistics counters with selectable
clear-on-read behavior and programmable interrupts on
half maximum value.
• Programmable Rx address filters, including a 64-bin
address hash table for multicast and/or unicast frames, and
programmable filter modes for broadcast, multicast, unicast, control, and damaged frames.
• Advanced power management supporting unattended
transfer of Rx and Tx frames and status to/from external
memory via DMA during low power sleep mode.
• System wakeup from sleep operating mode upon magic
packet or any of four user-definable wakeup frame filters.
• Support of MII and RMII protocols for external PHYs.
• Support for 802.3Q tagged VLAN frames.
• Full duplex and half duplex modes.
• Programmable MDC clock rate and preamble suppression.
• Data framing and encapsulation: generation and detection
of preamble, length padding, and FCS.
• In RMII operation, seven unused pins may be configured
as GPIO pins for other purposes.
• Media access management (in half-duplex operation): collision and contention handling, including control of
retransmission of collision frames and of back-off timing.
• Flow control (in full-duplex operation): generation and
detection of PAUSE frames.
• Station management: generation of MDC/MDIO frames
for read-write access to PHY registers.
PORTS
Because of the rich set of peripherals, the processor groups the
many peripheral signals to four ports—Port F, Port G, Port H,
and Port J. Most of the associated pins are shared by multiple
signals. The ports function as multiplexer controls.
General-Purpose I/O (GPIO)
• Operating range for active and sleep operating modes, see
Table 58 on Page 68 and Table 59 on Page 68.
• Internal loopback from Tx to Rx.
Some advanced features are:
• Buffered crystal output to external PHY for support of a
single crystal system.
• Automatic checksum computation of IP header and IP
payload fields of Rx frames.
The processor has 48 bidirectional, general-purpose I/O (GPIO)
pins allocated across three separate GPIO modules—PORTFIO,
PORTGIO, and PORTHIO, associated with Port F, Port G, and
Port H, respectively. Port J does not provide GPIO functionality. Each GPIO-capable pin shares functionality with other
processor peripherals via a multiplexing scheme; however, the
GPIO functionality is the default state of the device upon
power-up. Neither GPIO output nor input drivers are active by
default.
• Independent 32-bit descriptor-driven Rx and Tx DMA
channels.
• Frame status delivery to memory via DMA, including
frame completion semaphores, for efficient buffer queue
management in software.
• Tx DMA support for separate descriptors for MAC header
and payload to eliminate buffer copy operations.
Rev. D
|
Page 12 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Each general-purpose port pin can be individually controlled by
manipulation of the port control, status, and interrupt registers:
• GPIO direction control register — Specifies the direction of
each individual GPIO pin as input or output.
• GPIO control and status registers — The processor
employs a “write one to modify” mechanism that allows
any combination of individual GPIO pins to be modified in
a single instruction, without affecting the level of any other
GPIO pins. Four control registers are provided. One register is written in order to set pin values, one register is
written in order to clear pin values, one register is written
in order to toggle pin values, and one register is written in
order to specify a pin value. Reading the GPIO status register allows software to interrogate the sense of the pins.
• GPIO interrupt mask registers — The two GPIO interrupt
mask registers allow each individual GPIO pin to function
as an interrupt to the processor. Similar to the two GPIO
control registers that are used to set and clear individual
pin values, one GPIO interrupt mask register sets bits to
enable interrupt function, and the other GPIO interrupt
mask register clears bits to disable interrupt function.
GPIO pins defined as inputs can be configured to generate
hardware interrupts, while output pins can be triggered by
software interrupts.
• GPIO interrupt sensitivity registers — The two GPIO interrupt sensitivity registers specify whether individual pins are
level- or edge-sensitive and specify—if edge-sensitive—
whether just the rising edge or both the rising and falling
edges of the signal are significant. One register selects the
type of sensitivity, and one register selects which edges are
significant for edge-sensitivity.
PARALLEL PERIPHERAL INTERFACE (PPI)
The processor provides a parallel peripheral interface (PPI) that
can connect directly to parallel analog-to-digital and digital-toanalog converters, video encoders and decoders, and other general-purpose peripherals. The PPI consists of a dedicated input
clock pin, up to three frame synchronization pins, and up to 16
data pins. The input clock supports parallel data rates up to half
the system clock rate, and the synchronization signals can be
configured as either inputs or outputs.
The PPI supports a variety of general-purpose and ITU-R 656
modes of operation. In general-purpose mode, the PPI provides
half-duplex, bidirectional data transfer with up to 16 bits of
data. Up to three frame synchronization signals are also provided. In ITU-R 656 mode, the PPI provides half-duplex
bidirectional transfer of 8- or 10-bit video data. Additionally,
on-chip decode of embedded start-of-line (SOL) and start-offield (SOF) preamble packets is supported.
2. Frame capture mode — Frame syncs are outputs from the
PPI, but data are inputs.
3. Output mode — Frame syncs and data are outputs from
the PPI.
Input Mode
Input mode is intended for ADC applications, as well as video
communication with hardware signaling. In its simplest form,
PPI_FS1 is an external frame sync input that controls when to
read data. The PPI_DELAY MMR allows for a delay (in PPI_CLK cycles) between reception of this frame sync and the
initiation of data reads. The number of input data samples is
user programmable and defined by the contents of the
PPI_COUNT register. The PPI supports 8-bit and 10-bit
through 16-bit data, programmable in the PPI_CONTROL
register.
Frame Capture Mode
Frame capture mode allows the video source(s) to act as a slave
(for frame capture for example). The ADSP-BF52x processors
control when to read from the video source(s). PPI_FS1 is an
HSYNC output, and PPI_FS2 is a VSYNC output.
Output Mode
Output mode is used for transmitting video or other data with
up to three output frame syncs. Typically, a single frame sync is
appropriate for data converter applications, whereas two or
three frame syncs could be used for sending video with hardware signaling.
ITU-R 656 Mode Descriptions
The ITU-R 656 modes of the PPI are intended to suit a wide
variety of video capture, processing, and transmission applications. Three distinct submodes are supported:
1. Active video only mode
2. Vertical blanking only mode
3. Entire field mode
Active Video Mode
Active video only mode is used when only the active video portion of a field is of interest and not any of the blanking intervals.
The PPI does not read in any data between the end of active
video (EAV) and start of active video (SAV) preamble symbols,
or any data present during the vertical blanking intervals. In this
mode, the control byte sequences are not stored to memory;
they are filtered by the PPI. After synchronizing to the start of
Field 1, the PPI ignores incoming samples until it sees an SAV
code. The user specifies the number of active video lines per
frame (in PPI_COUNT register).
Vertical Blanking Interval Mode
General-Purpose Mode Descriptions
The general-purpose modes of the PPI are intended to suit a
wide variety of data capture and transmission applications.
Three distinct submodes are supported:
In this mode, the PPI only transfers vertical blanking interval
(VBI) data.
1. Input mode — Frame syncs and data are inputs into the
PPI.
Rev. D |
Page 13 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Entire Field Mode
DYNAMIC POWER MANAGEMENT
In this mode, the entire incoming bit stream is read in through
the PPI. This includes active video, control preamble sequences,
and ancillary data that may be embedded in horizontal and vertical blanking intervals. Data transfer starts immediately after
synchronization to Field 1. Data is transferred to or from the
synchronous channels through eight DMA engines that work
autonomously from the processor core.
The processor provides five operating modes, each with a different performance/power profile. In addition, dynamic power
management provides the control functions to dynamically alter
the processor core supply voltage, further reducing power dissipation. When configured for a 0 V core supply voltage, the
processor enters the hibernate state. Control of clocking to each
of the processor peripherals also reduces power consumption.
See Table 4 for a summary of the power settings for each mode.
USB ON-THE-GO DUAL-ROLE DEVICE CONTROLLER
The USB OTG dual-role device controller (USBDRC) provides
a low-cost connectivity solution for consumer mobile devices
such as cell phones, digital still cameras, and MP3 players,
allowing these devices to transfer data using a point-to-point
USB connection without the need for a PC host. The USBDRC
module can operate in a traditional USB peripheral-only mode
as well as the host mode presented in the On-the-Go (OTG)
supplement to the USB 2.0 specification. In host mode, the USB
module supports transfers at high speed (480 Mbps), full speed
(12 Mbps), and low speed (1.5 Mbps) rates. Peripheral-only
mode supports the high- and full-speed transfer rates.
The USB clock (USB_XI) is provided through a dedicated external crystal or crystal oscillator. See Universal Serial Bus (USB)
On-The-Go—Receive and Transmit Timing on Page 60 for
related timing requirements. If using a crystal to provide the
USB clock, use a parallel-resonant, fundamental mode, microprocessor-grade crystal.
The USB on-the-go dual-role device controller includes a phase
locked loop with programmable multipliers to generate the necessary internal clocking frequency for USB. The multiplier value
should be programmed based on the USB_XI frequency to
achieve the necessary 480 MHz internal clock for USB high
speed operation. For example, for a USB_XI crystal frequency of
24 MHz, the USB_PLLOSC_CTRL register should be programmed with a multiplier value of 20 to generate a 480 MHz
internal clock.
Table 4. Power Settings
PLL
Mode/State PLL
Bypassed
Full-On
Enabled No
Active
Enabled/ Yes
Disabled
Sleep
Enabled —
Deep Sleep Disabled —
Hibernate
Disabled —
Core
Clock
(CCLK)
Enabled
Enabled
System
Clock
(SCLK)
Enabled
Enabled
Core
Power
On
On
Disabled Enabled On
Disabled Disabled On
Disabled Disabled Off
Full-On Operating Mode—Maximum Performance
In the full-on mode, the PLL is enabled and is not bypassed,
providing capability for maximum operational frequency. This
is the power-up default execution state in which maximum performance can be achieved. The processor core and all enabled
peripherals run at full speed.
Active Operating Mode—Moderate Dynamic Power
Savings
In the active mode, the PLL is enabled but bypassed. Because the
PLL is bypassed, the processor’s core clock (CCLK) and system
clock (SCLK) run at the input clock (CLKIN) frequency. DMA
access is available to appropriately configured L1 memories.
In the active mode, it is possible to disable the control input to
the PLL by setting the PLL_OFF bit in the PLL control register.
This register can be accessed with a user-callable routine in the
on-chip ROM called bfrom_SysControl(). If disabled, the PLL
control input must be re-enabled before transitioning to the
full-on or sleep modes.
CODE SECURITY WITH LOCKBOX SECURE
TECHNOLOGY
A security system consisting of a blend of hardware and software provides customers with a flexible and rich set of code
security features with LockboxTM Secure Technology. Key features include:
For more information about PLL controls, see the “Dynamic
Power Management” chapter in the ADSP-BF52x Blackfin Processor Hardware Reference.
• OTP memory
• Unique chip ID
• Code authentication
Sleep Operating Mode—High Dynamic Power Savings
• Secure mode of operation
The sleep mode reduces dynamic power dissipation by disabling
the clock to the processor core (CCLK). The PLL and system
clock (SCLK), however, continue to operate in this mode. Typically, an external event or RTC activity wakes up the processor.
When in the sleep mode, asserting a wakeup enabled in the
SIC_IWRx registers causes the processor to sense the value of
the BYPASS bit in the PLL control register (PLL_CTL). If
BYPASS is disabled, the processor transitions to the full-on
mode. If BYPASS is enabled, the processor transitions to the
active mode.
The security scheme is based upon the concept of authentication of digital signatures using standards-based algorithms and
provides a secure processing environment in which to execute
code and protect assets. See Lockbox Secure Technology Disclaimer on Page 22.
Rev. D
|
Page 14 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
System DMA access to L1 memory is not supported in
sleep mode.
Power Savings
Deep Sleep Operating Mode—Maximum Dynamic Power
Savings
The deep sleep mode maximizes dynamic power savings by disabling the clocks to the processor core (CCLK) and to all
synchronous peripherals (SCLK). Asynchronous peripherals,
such as the RTC, may still be running but cannot access internal
resources or external memory. This powered-down mode can
only be exited by assertion of the reset interrupt (RESET) or by
an asynchronous interrupt generated by the RTC. When in deep
sleep mode, an RTC asynchronous interrupt causes the processor to transition to the Active mode. Assertion of RESET while
in deep sleep mode causes the processor to transition to the full
on mode.
Hibernate State—Maximum Static Power Savings
The hibernate state maximizes static power savings by disabling
the voltage and clocks to the processor core (CCLK) and to all of
the synchronous peripherals (SCLK). The internal voltage regulator (ADSP-BF523/ADSP-BF525/ADSP-BF527 only) for the
processor can be shut off by writing b#00 to the FREQ bits of the
VR_CTL register, using the bfrom_SysControl() function. This
setting sets the internal power supply voltage (VDDINT) to 0 V to
provide the lowest static power dissipation. Any critical information stored internally (for example, memory contents,
register contents, and other information) must be written to a
non volatile storage device prior to removing power if the processor state is to be preserved. Writing b#00 to the FREQ bits
also causes EXT_WAKE0 and EXT_WAKE1 to transition low,
which can be used to signal an external voltage regulator to
shut down.
Since VDDEXT and VDDMEM can still be supplied in this mode, all
of the external pins three-state, unless otherwise specified. This
allows other devices that may be connected to the processor to
still have power applied without drawing unwanted current.
The Ethernet or USB modules can wake up the internal supply
regulator (ADSP-BF525 and ADSP-BF527 only) or signal an
external regulator to wake up using EXT_WAKE0 or
EXT_WAKE1. If PG15 does not connect as a PHYINT signal to
an external PHY device, PG15 can be pulled low by any other
device to wake the processor up. The processor can also be
woken up by a real-time clock wakeup event or by asserting the
RESET pin. All hibernate wake-up events initiate the hardware
reset sequence. Individual sources are enabled by the VR_CTL
register. The EXT_WAKEx signals are provided to indicate the
occurrence of wake-up events.
As long as VDDEXT is applied, the VR_CTL register maintains its
state during hibernation. All other internal registers and memories, however, lose their content in the hibernate state. State
variables may be held in external SRAM or SDRAM. The
SCKELOW bit in the VR_CTL register controls whether or not
SDRAM operates in self-refresh mode, which allows it to retain
its content while the processor is in hibernate and through the
subsequent reset sequence.
Rev. D |
As shown in Table 5, the processor supports six different power
domains, which maximizes flexibility while maintaining compliance with industry standards and conventions. By isolating
the internal logic of the processor into its own power domain,
separate from the RTC and other I/O, the processor can take
advantage of dynamic power management without affecting the
RTC or other I/O devices. There are no sequencing requirements for the various power domains, but all domains must be
powered according to the appropriate Specifications table for
processor Operating Conditions; even if the feature/peripheral
is not used.
Table 5. Power Domains
Power Domain
All internal logic, except RTC, Memory, USB, OTP
RTC internal logic and crystal I/O
Memory logic
USB PHY logic
OTP logic
All other I/O
VDD Range
VDDINT
VDDRTC
VDDMEM
VDDUSB
VDDOTP
VDDEXT
The dynamic power management feature of the processor
allows both the processor’s input voltage (VDDINT) and clock frequency (fCCLK) to be dynamically controlled.
The power dissipated by a processor is largely a function of its
clock frequency and the square of the operating voltage. For
example, reducing the clock frequency by 25% results in a 25%
reduction in dynamic power dissipation, while reducing the
voltage by 25% reduces dynamic power dissipation by more
than 40%. Further, these power savings are additive, in that if
the clock frequency and supply voltage are both reduced, the
power savings can be dramatic, as shown in the following
equations.
Power Savings Factor
f CCLKRED
V DDINTRED 2
T RED
= --------------------------   --------------------------------   --------------- 



f CCLKNOM
V DDINTNOM
T NOM 
% Power Savings =  1 – Power Savings Factor   100%
where the variables in the equations are:
fCCLKNOM is the nominal core clock frequency
fCCLKRED is the reduced core clock frequency
VDDINTNOM is the nominal internal supply voltage
VDDINTRED is the reduced internal supply voltage
TNOM is the duration running at fCCLKNOM
TRED is the duration running at fCCLKRED
Page 15 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
ADSP-BF523/ADSP-BF525/ADSP-BF527
VOLTAGE REGULATION
The ADSP-BF523/ADSP-BF525/ADSP-BF527 provides an onchip voltage regulator that can generate processor core voltage
levels from an external supply. Figure 5 shows the typical external components required to complete the power management
system.
2.25V TO 3.6V
INPUT VOLTAGE
RANGE
VDDEXT
(LOW-INDUCTANCE)
SET OF DECOUPLING
CAPACITORS
+
ADSP-BF522/ADSP-BF524/ADSP-BF526
VOLTAGE REGULATION
VDDEXT
100μF
100μF
10μH
100nF
VDDINT
+
+
FDS9431A
10μ F
LOW ESR
ZHCS1000
100μF
SS/PG
VROUT
SHORT AND LOWINDUCTANCE WIRE
EXT_WAKE1
SEE H/W REFERENCE,
SYSTEM DESIGN CHAPTER,
TO DETERMINE VALUE
regulator, it is Power Good. The Soft Start feature is recommended to reduce the inrush currents and to reduce VDDINT
voltage overshoot when coming out of hibernate or changing
voltage levels. The Power Good (PG) input signal allows the
processor to start only after the internal voltage has reached a
chosen level. In this way, the startup time of the external
regulator is detected after hibernation. For a complete
description of Soft Start and Power Good functionality, refer
to the ADSP-BF52x Blackfin Processor Hardware Reference.
VRSEL
GND
NOTE: DESIGNER SHOULD MINIMIZE
TRACE LENGTH TO FDS9431A.
Figure 5. ADSP-BF523/ADSP-BF525/ADSP-BF527 Voltage Regulator Circuit
The regulator controls the internal logic voltage levels and is
programmable with the voltage regulator control register
(VR_CTL) in increments of 50 mV. This register can be
accessed using the bfrom_SysControl() function in the on-chip
ROM. To reduce standby power consumption, the internal voltage regulator can be programmed to remove power to the
processor core while keeping I/O power supplied. While in the
hibernate state, all external supplies (VDDEXT, VDDMEM, VDDUSB,
VDDOTP) can still be applied, eliminating the need for external
buffers. VDDRTC must be applied at all times for correct hibernate
operation. The voltage regulator can be activated from this
power-down state either through an RTC wakeup, a USB wakeup, an Ethernet wake-up, or by asserting the RESET pin, each of
which then initiates a boot sequence. The regulator can also be
disabled and bypassed at the user’s discretion.
The voltage regulator has two modes set by the VRSEL pin—the
normal pulse width control of an external FET and the external
supply mode which can signal a power down during hibernate
to an external regulator. Set VRSEL to VDDEXT to use an external
regulator or set VRSEL to GND to use the internal regulator. In
the external mode VROUT becomes EXT_WAKE1. If the internal
regulator is used, EXT_WAKE0 can control other power
sources in the system during the hibernate state. Both signals
are high-true for power-up and may be connected directly to the
low-true shutdown input of many common regulators. The
mode of the SS/PG (Soft Start/Power Good) signal also changes
according to the state of VRSEL. When using an internal regulator, the SS/PG pin is Soft Start, and when using an external
Rev. D
|
The ADSP-BF522/ADSP-BF524/ADSP-BF526 processor
requires an external voltage regulator to power the VDDINT
domain. To reduce standby power consumption, the external
voltage regulator can be signaled through EXT_WAKE0 or
EXT_WAKE1 to remove power from the processor core. These
identical signals are high-true for power-up and may be connected directly to the low-true shut down input of many
common regulators. While in the hibernate state, all external
supplies (VDDEXT, VDDMEM, VDDUSB, VDDOTP) can still be applied,
eliminating the need for external buffers. VDDRTC must be
applied at all times for correct hibernate operation. The external
voltage regulator can be activated from this power down state
either through an RTC wakeup, a USB wakeup, an Ethernet
wakeup, or by asserting the RESET pin, each of which then initiates a boot sequence. EXT_WAKE0 or EXT_WAKE1 indicate a
wakeup to the external voltage regulator. The Power Good (PG)
input signal allows the processor to start only after the internal
voltage has reached a chosen level. In this way, the startup time
of the external regulator is detected after hibernation. For a
complete description of the Power Good functionality, refer to
the ADSP-BF52x Blackfin Processor Hardware Reference.
CLOCK SIGNALS
The processor can be clocked by an external crystal, a sine wave
input, or a buffered, shaped clock derived from an external
clock oscillator.
If an external clock is used, it should be a TTL compatible signal
and must not be halted, changed, or operated below the specified frequency during normal operation. This signal is
connected to the processor’s CLKIN pin. When an external
clock is used, the XTAL pin must be left unconnected.
Alternatively, because the processor includes an on-chip oscillator circuit, an external crystal may be used. For fundamental
frequency operation, use the circuit shown in Figure 6. A
parallel-resonant, fundamental frequency, microprocessorgrade crystal is connected across the CLKIN and XTAL pins.
The on-chip resistance between CLKIN and the XTAL pin is in
the 500 kΩ range. Further parallel resistors are typically not recommended. The two capacitors and the series resistor shown in
Figure 6 fine tune phase and amplitude of the sine frequency.
The capacitor and resistor values shown in Figure 6 are typical
values only. The capacitor values are dependent upon the crystal
manufacturers’ load capacitance recommendations and the PCB
physical layout. The resistor value depends on the drive level
Page 16 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
specified by the crystal manufacturer. The user should verify the
customized values based on careful investigations on multiple
devices over temperature range.
BLACKFIN
permitted to run up to the frequency specified by the part’s
maximum instruction rate. The CLKOUT pin reflects the SCLK
frequency to the off-chip world. It is part of the SDRAM interface, but it functions as a reference signal in other timing
specifications as well. While active by default, it can be disabled
using the EBIU_SDGCTL and EBIU_AMGCTL registers.
CLKOUT
TO PLL CIRCUITRY
“FINE” ADJUSTMENT
REQUIRES PLL SEQUENCING
EN
“COARSE” ADJUSTMENT
ON-THE-FLY
CLKBUF
560 ⍀
EN
PLL
5u to 64u
CLKIN
XTAL
CLKIN
330 ⍀*
18 pF *
÷ 1, 2, 4, 8
CCLK
÷ 1 to 15
SCLK
VCO
FOR OVERTONE
OPERATION ONLY:
18 pF *
SCLK d CCLK
Figure 7. Frequency Modification Methods
NOTE: VALUES MARKED WITH * MUST BE CUSTOMIZED, DEPENDING
ON THE CRYSTAL AND LAYOUT. PLEASE ANALYZE CAREFULLY. FOR
FREQUENCIES ABOVE 33 MHz, THE SUGGESTED CAPACITOR VALUE
OF 18 pF SHOULD BE TREATED AS A MAXIMUM, AND THE SUGGESTED
RESISTOR VALUE SHOULD BE REDUCED TO 0 ⍀.
Figure 6. External Crystal Connections
A third-overtone crystal can be used for frequencies above
25 MHz. The circuit is then modified to ensure crystal operation
only at the third overtone by adding a tuned inductor circuit as
shown in Figure 6. A design procedure for third-overtone operation is discussed in detail in application note (EE-168) Using
Third Overtone Crystals with the ADSP-218x DSP on the Analog
Devices website (www.analog.com)—use site search on
“EE-168.”
The CLKBUF pin is an output pin, which is a buffered version
of the input clock. This pin is particularly useful in Ethernet
applications to limit the number of required clock sources in the
system. In this type of application, a single 25 MHz or 50 MHz
crystal may be applied directly to the processor. The 25 MHz or
50 MHz output of CLKBUF can then be connected to an external Ethernet MII or RMII PHY device. If, instead of a crystal, an
external oscillator is used at CLKIN, CLKBUF will not have the
40/60 duty cycle required by some devices. The CLKBUF output
is active by default and can be disabled for power savings reasons using the VR_CTL register.
The Blackfin core runs at a different clock rate than the on-chip
peripherals. As shown in Figure 7, the core clock (CCLK) and
system peripheral clock (SCLK) are derived from the input
clock (CLKIN) signal. An on-chip PLL is capable of multiplying
the CLKIN signal by a programmable multiplication factor
(bounded by specified minimum and maximum VCO frequencies). The default multiplier can be modified by a software
instruction sequence. This sequence is managed by the
bfrom_SysControl() function in the on-chip ROM.
On-the-fly CCLK and SCLK frequency changes can be applied
by using the bfrom_SysControl() function in the on-chip ROM.
The maximum allowed CCLK and SCLK rates depend on the
applied voltages VDDINT, VDDEXT, and VDDMEM; the VCO is always
Rev. D |
All on-chip peripherals are clocked by the system clock (SCLK).
The system clock frequency is programmable by means of the
SSEL3–0 bits of the PLL_DIV register. The values programmed
into the SSEL fields define a divide ratio between the PLL output
(VCO) and the system clock. SCLK divider values are 1 through
15. Table 6 illustrates typical system clock ratios.
Note that the divisor ratio must be chosen to limit the system
clock frequency to its maximum of fSCLK. The SSEL value can be
dynamically changed without any PLL lock latencies by writing
the appropriate values to the PLL divisor register (PLL_DIV)
using the bfrom_SysControl() function in the on-chip ROM.
Table 6. Example System Clock Ratios
Signal Name
SSEL3–0
0001
0110
1010
Divider Ratio
VCO/SCLK
1:1
6:1
10:1
Example Frequency Ratios
(MHz)
VCO
SCLK
100
100
300
50
500
50
The core clock (CCLK) frequency can also be dynamically
changed by means of the CSEL1–0 bits of the PLL_DIV register.
Supported CCLK divider ratios are 1, 2, 4, and 8, as shown in
Table 7. This programmable core clock capability is useful for
fast core frequency modifications.
Table 7. Core Clock Ratios
Signal Name
CSEL1–0
00
01
10
11
Page 17 of 88 | July 2013
Divider Ratio
VCO/CCLK
1:1
2:1
4:1
8:1
Example Frequency Ratios
(MHz)
VCO
CCLK
300
300
300
150
500
125
200
25
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
The maximum CCLK frequency not only depends on the part's
maximum instruction rate (see Page 88). This frequency also
depends on the applied VDDINT voltage. See Table 12 and
Table 15 for details. The maximal system clock rate (SCLK)
depends on the chip package and the applied VDDINT, VDDEXT,
and VDDMEM voltages (see Table 14 and Table 17).
BOOTING MODES
The processor has several mechanisms (listed in Table 8) for
automatically loading internal and external memory after a
reset. The boot mode is defined by four BMODE input pins
dedicated to this purpose. There are two categories of boot
modes. In master boot modes the processor actively loads data
from parallel or serial memories. In slave boot modes the processor receives data from external host devices.
The boot modes listed in Table 8 provide a number of mechanisms for automatically loading the processor’s internal and
external memories after a reset. By default, all boot modes use
the slowest meaningful configuration settings. Default settings
can be altered via the initialization code feature at boot time or
by proper OTP programming at pre-boot time. The BMODE
pins of the reset configuration register, sampled during poweron resets and software-initiated resets, implement the modes
shown in Table 8.
Table 8. Booting Modes
BMODE3–0
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
• Boot from 16-bit asynchronous FIFO (BMODE = 0x2) —
In this mode, the boot kernel starts booting from address
0x2030 0000. Every 16-bit word that the boot kernel has to
read from the FIFO must be requested by placing a low
pulse on the DMAR1 pin.
• Boot from serial SPI memory, EEPROM or flash
(BMODE = 0x3) — 8-, 16-, 24-, or 32-bit addressable
devices are supported. The processor uses the PG1 GPIO
pin to select a single SPI EEPROM/flash device and submits a read command and successive address bytes (0x00)
until a valid 8-, 16-, 24-, or 32-bit addressable device is
detected. Pull-up resistors are required on the SPISEL1 and
MISO pins. By default, a value of 0x85 is written to the
SPI_BAUD register.
• Boot from serial TWI memory, EEPROM/flash
(BMODE = 0x5) — The processor operates in master mode
and selects the TWI slave connected to the TWI with the
unique ID 0xA0.
• Idle/no boot mode (BMODE = 0x0) — In this mode, the
processor goes into idle. The idle boot mode helps recover
from illegal operating modes, such as when the OTP memory has been misconfigured.
• Boot from 8-bit or 16-bit external flash memory
(BMODE = 0x1) — In this mode, the boot kernel loads the
first block header from address 0x2000 0000, and (depending on instructions contained in the header) the boot
|
The ARDY is not enabled by default, but it can be enabled
through OTP programming. Similarly, all interface behavior and timings can be customized through OTP
programming. This includes activation of burst-mode or
page-mode operation. In this mode, all asynchronous
interface signals are enabled at the port muxing level.
• Boot from SPI host device (BMODE = 0x4) — The processor operates in SPI slave mode and is configured to receive
the bytes of the LDR file from an SPI host (master) agent.
The HWAIT signal must be interrogated by the host before
every transmitted byte. A pull-up resistor is required on the
SPISS input. A pull-down on the serial clock (SCK) may
improve signal quality and booting robustness.
Description
Idle — No boot
Boot from 8- or 16-bit external flash memory
Boot from 16-bit asynchronous FIFO
Boot from serial SPI memory (EEPROM or flash)
Boot from SPI host device
Boot from serial TWI memory (EEPROM/flash)
Boot from TWI host
Boot from UART0 Host
Boot from UART1 Host
Reserved
Boot from SDRAM
Boot from OTP memory
Boot from 8-bit NAND flash
via NFC using PORTF data pins
Boot from 8-bit NAND flash
via NFC using PORTH data pins
Boot from 16-Bit Host DMA
Boot from 8-Bit Host DMA
Rev. D
kernel performs an 8- or 16-bit boot or starts program execution at the address provided by the header. By default, all
configuration settings are set for the slowest device possible
(3-cycle hold time, 15-cycle R/W access times, 4-cycle
setup).
The processor submits successive read commands to the
memory device starting at internal address 0x0000 and
begins clocking data into the processor. The TWI memory
device should comply with the Philips I2C® Bus Specification version 2.1 and should be able to auto-increment its
internal address counter such that the contents of the
memory device can be read sequentially. By default, a
PRESCALE value of 0xA and a TWI_CLKDIV value of
0x0811 are used. Unless altered by OTP settings, an I2C
memory that takes two address bytes is assumed. The
development tools ensure that data booted to memories
that cannot be accessed by the Blackfin core is written to an
intermediate storage location and then copied to the final
destination via memory DMA.
• Boot from TWI host (BMODE = 0x6) — The TWI host
selects the slave with the unique ID 0x5F.
The processor replies with an acknowledgement and the
host then downloads the boot stream. The TWI host agent
should comply with the Philips I2C Bus Specification
Page 18 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
version 2.1. An I2C multiplexer can be used to select one
processor at a time when booting multiple processors from
a single TWI.
• Boot from UART0 host on Port G (BMODE = 0x7) —
Using an autobaud handshake sequence, a boot-stream formatted program is downloaded by the host. The host
selects a bit rate within the UART clocking capabilities.
When performing the autobaud, the UART expects a “@”
(0x40) character (eight bits data, one start bit, one stop bit,
no parity bit) on the UART0RX pin to determine the bit
rate. The UART then replies with an acknowledgement
composed of 4 bytes (0xBF, the value of UART0_DLL, the
value of UART0_DLH, then 0x00). The host can then
download the boot stream. To hold off the host the Blackfin
processor signals the host with the boot host wait
(HWAIT) signal. Therefore, the host must monitor
HWAIT before every transmitted byte.
—Software-configurable boot mode for booting from
boot streams spanning multiple blocks, including bad
blocks
—Software-configurable boot mode for booting from
multiple copies of the boot stream, allowing for handling of bad blocks and uncorrectable errors
—Configurable timing via OTP memory
Small page NAND flash devices must have a 512-byte page
size, 32 pages per block, a 16-byte spare area size, and a bus
configuration of 8 bits. By default, all read requests from
the NAND flash are followed by four address cycles. If the
NAND flash device requires only three address cycles, the
device must be capable of ignoring the additional address
cycles.
The small page NAND flash device must comply with the
following command set:
• Boot from UART1 host on Port F (BMODE = 0x8). Same
as BMODE = 0x7 except that the UART1 port is used.
—Reset: 0xFF
• Boot from SDRAM (BMODE = 0xA) This is a warm boot
scenario, where the boot kernel starts booting from address
0x0000 0010. The SDRAM is expected to contain a valid
boot stream and the SDRAM controller must be configured
by the OTP settings.
—Read upper half of page: 0x01
• Boot from OTP memory (BMODE = 0xB) — This provides
a stand-alone booting method. The boot stream is loaded
from on-chip OTP memory. By default, the boot stream is
expected to start from OTP page 0x40 and can occupy all
public OTP memory up to page 0xDF. This is 2560 bytes.
Since the start page is programmable, the maximum size of
the boot stream can be extended to 3072 bytes.
• Boot from 8-bit external NAND flash memory (BMODE =
0xC and BMODE = 0xD) — In this mode, auto detection of
the NAND flash device is performed.
—Read spare area: 0x50
For large-page NAND-flash devices, the four-byte electronic signature is read in order to configure the kernel for
booting, which allows support for multiple large-page
devices. The fourth byte of the electronic signature must
comply with the specification in Table 9 on Page 20.
Any NAND flash array configuration from Table 9, excluding 16-bit devices, that also complies with the command set
listed below are directly supported by the boot kernel.
There are no restrictions on the page size or block size as
imposed by the small-page boot kernel.
For devices consisting of a five-byte signature, only four are
read. The fourth must comply as outlined above.
Large page devices must support the following command
set:
BMODE = 0xC, the processor configures PORTF GPIO
pins PF7:0 for the NAND data pins and PORTH pins
PH15:10 for the NAND control signals.
—Reset: 0xFF
BMODE = 0xD, the processor configures PORTH GPIO
pins PH7:0 for the NAND data pins and PORTH pins
PH15:10 for the NAND control signals.
—Read Electronic Signature: 0x90
—Read: 0x00, 0x30 (confirm command)
For correct device operation pull-up resistors are required
on both ND_CE (PH10) and ND_BUSY (PH13) signals. By
default, a value of 0x0033 is written to the NFC_CTL register. The booting procedure always starts by booting from
byte 0 of block 0 of the NAND flash device.
NAND flash boot supports the following features:
—Device Auto Detection
—Error Detection & Correction for maximum reliability
—No boot stream size limitation
—Peripheral DMA providing efficient transfer of all data
(excluding the ECC parity data)
Rev. D |
—Read lower half of page: 0x00
Large-page devices must not support or react to NAND
flash command 0x50. This is a small-page NAND flash
command used for device auto detection.
By default, the boot kernel will always issue five address
cycles; therefore, if a large page device requires only four
cycles, the device must be capable of ignoring the additional address cycles.
• Boot from 16-Bit Host DMA (BMODE = 0xE) — In this
mode, the host DMA port is configured in 16-bit Acknowledge mode, with little endian data formatting. Unlike other
modes, the host is responsible for interpreting the boot
stream. It writes data blocks individually into the Host
DMA port. Before configuring the DMA settings for each
block, the host may either poll the ALLOW_CONFIG bit in
HOST_STATUS or wait to be interrupted by the HWAIT
Page 19 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
signal. When using HWAIT, the host must still check
ALLOW_CONFIG at least once before beginning to configure the Host DMA Port. After completing the
configuration, the host is required to poll the READY bit in
HOST_STATUS before beginning to transfer data. When
the host sends an HIRQ control command, the boot kernel
issues a CALL instruction to address 0xFFA0 0000. It is the
host's responsibility to ensure that valid code has been
placed at this address. The routine at 0xFFA0 0000 can be a
simple initialization routine to configure internal
resources, such as the SDRAM controller, which then
returns using an RTS instruction. The routine may also by
the final application, which will never return to the boot
kernel.
• Boot from 8-Bit Host DMA (BMODE = 0xF) — In this
mode, the Host DMA port is configured in 8-bit interrupt
mode, with little endian data formatting. Unlike other
modes, the host is responsible for interpreting the boot
stream. It writes data blocks individually into the Host
DMA port. Before configuring the DMA settings for each
block, the host may either poll the ALLOW_CONFIG bit in
HOST_STATUS or wait to be interrupted by the HWAIT
signal. When using HWAIT, the host must still check
ALLOW_CONFIG at least once before beginning to configure the Host DMA Port. The host will receive an
interrupt from the HOST_ACK signal every time it is
allowed to send the next FIFO depths worth (sixteen 32-bit
words) of information. When the host sends an HIRQ control command, the boot kernel issues a CALL instruction to
address 0xFFA0 0000. It is the host's responsibility to
ensure valid code has been placed at this address. The routine at 0xFFA0 0000 can be a simple initialization routine
to configure internal resources, such as the SDRAM controller, which then returns using an RTS instruction. The
routine may also by the final application, which will never
return to the boot kernel.
INSTRUCTION SET DESCRIPTION
The Blackfin processor family assembly language instruction set
employs an algebraic syntax designed for ease of coding and
readability. The instructions have been specifically tuned to provide a flexible, densely encoded instruction set that compiles to
a very small final memory size. The instruction set also provides
fully featured multifunction instructions that allow the programmer to use many of the processor core resources in a single
instruction. Coupled with many features more often seen on
microcontrollers, this instruction set is very efficient when compiling C and C++ source code. In addition, the architecture
supports both user (algorithm/application code) and supervisor (O/S kernel, device drivers, debuggers, ISRs) modes
of operation, allowing multiple levels of access to core
processor resources.
The assembly language, which takes advantage of the processor’s unique architecture, offers the following advantages:
• Seamlessly integrated DSP/MCU features are optimized for
both 8-bit and 16-bit operations.
• A multi-issue load/store modified-Harvard architecture,
which supports two 16-bit MAC or four 8-bit ALU + two
load/store + two pointer updates per cycle.
• All registers, I/O, and memory are mapped into a unified
4G byte memory space, providing a simplified programming model.
• Microcontroller features, such as arbitrary bit and bit-field
manipulation, insertion, and extraction; integer operations
on 8-, 16-, and 32-bit data-types; and separate user and
supervisor stack pointers.
• Code density enhancements, which include intermixing of
16-bit and 32-bit instructions (no mode switching, no code
segregation). Frequently used instructions are encoded
in 16 bits.
DEVELOPMENT TOOLS
Table 9. Fourth Byte for Large Page Devices
Bit
Parameter
Analog Devices supports its processors with a complete line of
software and hardware development tools, including integrated
development environments (which include CrossCore® Embedded Studio and/or VisualDSP++®), evaluation products,
emulators, and a wide variety of software add-ins.
Value
Meaning
00
01
10
11
1K byte
2K byte
4K byte
8K byte
Spare Area Size
00
01
8 byte/512 byte
16 byte/512 byte
For C/C++ software writing and editing, code generation, and
debug support, Analog Devices offers two IDEs.
D5:D4 Block Size
(excluding spare area)
00
01
10
11
64K byte
128K byte
256K byte
512K byte
D6
00
01
x8
not supported
The newest IDE, CrossCore Embedded Studio, is based on the
EclipseTM framework. Supporting most Analog Devices processor families, it is the IDE of choice for future processors,
including multicore devices. CrossCore Embedded Studio
seamlessly integrates available software add-ins to support real
time operating systems, file systems, TCP/IP stacks, USB stacks,
algorithmic software modules, and evaluation hardware board
support packages. For more information, visit www.analog.com/cces.
D1:D0 Page Size
(excluding spare area)
D2
Bus width
Integrated Development Environments (IDEs)
D3, D7 Not Used for configuration
Rev. D
|
Page 20 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
The other Analog Devices IDE, VisualDSP++, supports processor families introduced prior to the release of CrossCore
Embedded Studio. This IDE includes the Analog Devices VDK
real time operating system and an open source TCP/IP stack.
For more information visit www.analog.com/visualdsp. Note
that VisualDSP++ will not support future Analog Devices
processors.
Middleware Packages
Analog Devices separately offers middleware add-ins such as
real time operating systems, file systems, USB stacks, and TCP/
IP stacks. For more information see the following web pages:
• www.analog.com/ucos3
• www.analog.com/ucfs
EZ-KIT Lite Evaluation Board
• www.analog.com/ucusbd
For processor evaluation, Analog Devices provides wide range
of EZ-KIT Lite® evaluation boards. Including the processor and
key peripherals, the evaluation board also supports on-chip
emulation capabilities and other evaluation and development
features. Also available are various EZ-Extenders®, which are
daughter cards delivering additional specialized functionality,
including audio and video processing. For more information
visit www.analog.com and search on “ezkit” or “ezextender”.
• www.analog.com/lwip
EZ-KIT Lite Evaluation Kits
For a cost-effective way to learn more about developing with
Analog Devices processors, Analog Devices offer a range of EZKIT Lite evaluation kits. Each evaluation kit includes an EZ-KIT
Lite evaluation board, directions for downloading an evaluation
version of the available IDE(s), a USB cable, and a power supply.
The USB controller on the EZ-KIT Lite board connects to the
USB port of the user’s PC, enabling the chosen IDE evaluation
suite to emulate the on-board processor in-circuit. This permits
the customer to download, execute, and debug programs for the
EZ-KIT Lite system. It also supports in-circuit programming of
the on-board Flash device to store user-specific boot code,
enabling standalone operation. With the full version of CrossCore Embedded Studio or VisualDSP++ installed (sold
separately), engineers can develop software for supported EZKITs or any custom system utilizing supported Analog Devices
processors.
Software Add-Ins for CrossCore Embedded Studio
Analog Devices offers software add-ins which seamlessly integrate with CrossCore Embedded Studio to extend its capabilities
and reduce development time. Add-ins include board support
packages for evaluation hardware, various middleware packages, and algorithmic modules. Documentation, help,
configuration dialogs, and coding examples present in these
add-ins are viewable through the CrossCore Embedded Studio
IDE once the add-in is installed.
Algorithmic Modules
To speed development, Analog Devices offers add-ins that perform popular audio and video processing algorithms. These are
available for use with both CrossCore Embedded Studio and
VisualDSP++. For more information visit www.analog.com and
search on “Blackfin software modules” or “SHARC software
modules”.
Designing an Emulator-Compatible DSP Board (Target)
For embedded system test and debug, Analog Devices provides
a family of emulators. On each JTAG DSP, Analog Devices supplies an IEEE 1149.1 JTAG Test Access Port (TAP). In-circuit
emulation is facilitated by use of this JTAG interface. The emulator accesses the processor’s internal features via the
processor’s TAP, allowing the developer to load code, set breakpoints, and view variables, memory, and registers. The
processor must be halted to send data and commands, but once
an operation is completed by the emulator, the DSP system is set
to run at full speed with no impact on system timing. The emulators require the target board to include a header that supports
connection of the DSP’s JTAG port to the emulator.
For details on target board design issues including mechanical
layout, single processor connections, signal buffering, signal termination, and emulator pod logic, see the Engineer-to-Engineer
Note “Analog Devices JTAG Emulation Technical Reference”
(EE-68) on the Analog Devices website (www.analog.com)—use
site search on “EE-68.” This document is updated regularly to
keep pace with improvements to emulator support.
ADDITIONAL INFORMATION
The following publications that describe the ADSP-BF52x processors (and related processors) can be ordered from any
Analog Devices sales office or accessed electronically on
our website:
Board Support Packages for Evaluation Hardware
• Getting Started With Blackfin Processors
Software support for the EZ-KIT Lite evaluation boards and EZExtender daughter cards is provided by software add-ins called
Board Support Packages (BSPs). The BSPs contain the required
drivers, pertinent release notes, and select example code for the
given evaluation hardware. A download link for a specific BSP is
located on the web page for the associated EZ-KIT or EZExtender product. The link is found in the Product Download
area of the product web page.
• ADSP-BF52x Blackfin Processor Hardware Reference (volumes 1 and 2)
Rev. D |
• Blackfin Processor Programming Reference
• ADSP-BF522/ADSP-BF524/ADSP-BF526 Blackfin Processor Anomaly List
• ADSP-BF523/ADSP-BF525/ADSP-BF527 Blackfin Processor Anomaly List
Page 21 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
RELATED SIGNAL CHAINS
A signal chain is a series of signal-conditioning electronic components that receive input (data acquired from sampling either
real-time phenomena or from stored data) in tandem, with the
output of one portion of the chain supplying input to the next.
Signal chains are often used in signal processing applications to
gather and process data or to apply system controls based on
analysis of real-time phenomena. For more information about
this term and related topics, see the “signal chain” entry in
Wikipedia or the Glossary of EE Terms on the Analog Devices
website.
Analog Devices eases signal processing system development by
providing signal processing components that are designed to
work together well. A tool for viewing relationships between
specific applications and related components is available on the
www.analog.com website.
The Application Signal Chains page in the Circuits from the
LabTM site (http:\\www.analog.com\signalchains) provides:
• Graphical circuit block diagram presentation of signal
chains for a variety of circuit types and applications
• Drill down links for components in each chain to selection
guides and application information
• Reference designs applying best practice design techniques
LOCKBOX SECURE TECHNOLOGY DISCLAIMER
Analog Devices products containing Lockbox Secure Technology are warranted by Analog Devices as detailed in the Analog
Devices Standard Terms and Conditions of Sale. To our knowledge, the Lockbox Secure Technology, when used in accordance
with the data sheet and hardware reference manual specifications, provides a secure method of implementing code and data
safeguards. However, Analog Devices does not guarantee that
this technology provides absolute security.
ACCORDINGLY, ANALOG DEVICES HEREBY DISCLAIMS
ANY AND ALL EXPRESS AND IMPLIED WARRANTIES
THAT THE LOCKBOX SECURE TECHNOLOGY CANNOT
BE BREACHED, COMPROMISED, OR OTHERWISE CIRCUMVENTED AND IN NO EVENT SHALL ANALOG
DEVICES BE LIABLE FOR ANY LOSS, DAMAGE,
DESTRUCTION, OR RELEASE OF DATA, INFORMATION,
PHYSICAL PROPERTY, OR INTELLECTUAL PROPERTY.
Rev. D
|
Page 22 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
SIGNAL DESCRIPTIONS
Signal definitions for the ADSP-BF52x processors are listed in
Table 10. In order to maintain maximum function and reduce
package size and ball count, some balls have dual, multiplexed
functions. In cases where ball function is reconfigurable, the
default state is shown in plain text, while the alternate function
is shown in italics.
All pins are three-stated during and immediately after reset,
with the exception of the external memory interface, asynchronous and synchronous memory control, and the buffered XTAL
output pin (CLKBUF). On the external memory interface, the
control and address lines are driven high, with the exception of
CLKOUT, which toggles at the system clock rate. During hibernate, all outputs are three-stated unless otherwise noted in
Table 10.
All I/O pins have their input buffers disabled with the exception
of the pins that need pull-ups or pull-downs, as noted in
Table 10.
It is strongly advised to use the available IBIS models to ensure
that a given board design meets overshoot/undershoot and signal integrity requirements. If no IBIS simulation is performed, it
is strongly recommended to add series resistor terminations for
all Driver Types A, C and D.
The termination resistors should be placed near the processor to
reduce transients and improve signal integrity. The resistance
value, typically 33 Ω or 47 Ω, should be chosen to match the
average board trace impedance.
Additionally, adding a parallel termination to CLKOUT may
prove useful in further enhancing signal integrity. Be sure to
verify overshoot/undershoot and signal integrity specifications
on actual hardware.
Table 10. Signal Descriptions
Type Function
Driver
Type1
ADDR19–1
O
Address Bus
A
DATA15–0
I/O
Data Bus
A
ABE1–0/SDQM1–0
O
Byte Enables/Data Mask
A
Signal Name
EBIU
AMS3–0
O
Asynchronous Memory Bank Selects (Require pull-ups if hibernate is used.) A
ARDY
I
Hardware Ready Control
AOE
O
Asynchronous Output Enable
A
ARE
O
Asynchronous Read Enable
A
AWE
O
Asynchronous Write Enable
A
SRAS
O
SDRAM Row Address Strobe
A
SCAS
O
SDRAM Column Address Strobe
A
SWE
O
SDRAM Write Enable
A
SCKE
O
SDRAM Clock Enable (Requires a pull-down if hibernate with SDRAM selfrefresh is used.)
A
CLKOUT
O
SDRAM Clock Output
B
SA10
O
SDRAM A10 Signal
A
SMS
O
SDRAM Bank Select
A
Rev. D |
Page 23 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 10. Signal Descriptions (Continued)
Signal Name
Type Function
Driver
Type1
USB 2.0 HS OTG
USB_DP
I/O
Data + (This ball should be pulled low when USB is unused or not present.) F
USB_DM
I/O
Data – (This ball should be pulled low when USB is unused or not present.) F
USB_XI
I
USB Crystal Input (This ball should be pulled low when USB is unused or not
present.)
USB_XO
O
USB Crystal Output (This ball should be left unconnected when USB is unused F
or not present.)
USB_ID
I
USB OTG mode (This ball should be pulled low when USB is unused or not
present.)
USB_VREF
A
USB voltage reference (Connect to GND through a 0.1 μF capacitor or leave
unconnected when not used.)
USB_RSET
A
USB resistance set. (This ball should be left unconnected.)
USB_VBUS
I/O 5V USB VBUS. USB_VBUS is an output only in peripheral mode during SRP
F
signaling. Host mode requires that an external voltage source of 5 V at 8 mA
or more (per the OTG specification) be applied to VBUS. The voltage source
needs to be able to charge and discharge VBUS, thus an ON/OFF switch is
required to control the voltage source. A GPIO can be used for this purpose
(This ball should be pulled low when USB is unused or not present.)
Port F: GPIO and Multiplexed Peripherals
PF0/PPI D0/DR0PRI /ND_D0A
I/O
GPIO/PPI Data 0/SPORT0 Primary Receive Data
/NAND Alternate Data 0
C
PF1/PPI D1/RFS0/ND_D1A
I/O
GPIO/PPI Data 1/SPORT0 Receive Frame Sync
/NAND Alternate Data 1
C
PF2/PPI D2/RSCLK0/ND_D2A
I/O
GPIO/PPI Data 2/SPORT0 Receive Serial Clock
/NAND Alternate Data 2/Alternate Capture Input 0
D
PF3/PPI D3/DT0PRI/ND_D3A
I/O
GPIO/PPI Data 3/SPORT0 Transmit Primary Data
/NAND Alternate Data 3
C
PF4/PPI D4/TFS0/ND_D4A/TACLK0
I/O
GPIO/PPI Data 4/SPORT0 Transmit Frame Sync
/NAND Alternate Data 4/Alternate Timer Clock 0
C
PF5/PPI D5/TSCLK0/ND_D5A/TACLK1
I/O
GPIO/PPI Data 5/SPORT0 Transmit Serial Clock
/NAND Alternate Data 5/Alternate Timer Clock 1
D
PF6/PPI D6/DT0SEC/ND_D6A/TACI0
I/O
GPIO/PPI Data 6/SPORT0 Transmit Secondary Data
/NAND Alternate Data 6/Alternate Capture Input 0
C
PF7/PPI D7/DR0SEC/ND_D7A/TACI1
I/O
GPIO/PPI Data 7/SPORT0 Receive Secondary Data
/NAND Alternate Data 7/Alternate Capture Input 1
C
PF8/PPI D8/DR1PRI
I/O
GPIO/PPI Data 8/SPORT1 Primary Receive Data
C
PF9/PPI D9/RSCLK1/SPISEL6
I/O
GPIO/PPI Data 9/SPORT1 Receive Serial Clock/SPI Slave Select 6
D
PF10/PPI D10/RFS1/SPISEL7
I/O
GPIO/PPI Data 10/SPORT1 Receive Frame Sync/SPI Slave Select 7
C
PF11/PPI D11/TFS1/CZM
I/O
GPIO/PPI Data 11/SPORT1 Transmit Frame Sync/Counter Zero Marker
C
PF12/PPI D12/DT1PRI/SPISEL2/CDG
I/O
GPIO/PPI Data 12/SPORT1 Transmit Primary Data/SPI Slave Select 2/Counter
Down Gate
C
PF13/PPI D13/TSCLK1/SPISEL3/CUD
I/O
GPIO/PPI Data 13/SPORT1 Transmit Serial Clock/SPI Slave Select 3/Counter Up D
Direction
PF14/PPI D14/DT1SEC/UART1TX
I/O
GPIO/PPI Data 14/SPORT1 Transmit Secondary Data/UART1 Transmit
C
PF15/PPI D15/DR1SEC/UART1RX/TACI3
I/O
GPIO/PPI Data 15/SPORT1 Receive Secondary Data
/UART1 Receive /Alternate Capture Input 3
C
Rev. D
|
Page 24 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 10. Signal Descriptions (Continued)
Signal Name
Type Function
Driver
Type1
Port G: GPIO and Multiplexed Peripherals
PG0/HWAIT
I/O
GPIO/Boot Host Wait2
C
PG1/SPISS/SPISEL1
I/O
GPIO/SPI Slave Select Input/SPI Slave Select 1
C
PG2/SCK
I/O
GPIO/SPI Clock
D
PG3/MISO/DR0SECA
I/O
GPIO/SPI Master In Slave Out/Sport 0 Alternate Receive Data Secondary
C
PG4/MOSI/DT0SECA
I/O
GPIO/SPI Master Out Slave In/Sport 0 Alternate Transmit Data Secondary
C
PG5/TMR1/PPI_FS2
I/O
GPIO/Timer1/PPI Frame Sync2
C
PG6/DT0PRIA/TMR2/PPI_FS3
I/O
GPIO/SPORT0 Alternate Primary Transmit Data / Timer2 / PPI Frame Sync3
C
PG7/TMR3/DR0PRIA/UART0TX
I/O
GPIO/Timer3/Sport 0 Alternate Receive Data Primary/UART0 Transmit
C
PG8/TMR4/RFS0A/UART0RX/TACI4
I/O
GPIO/Timer 4/Sport 0 Alternate Receive Clock/Frame Sync
/UART0 Receive/Alternate Capture Input 4
C
PG9/TMR5/RSCLK0A/TACI5
I/O
GPIO/Timer5/Sport 0 Alternate Receive Clock
/Alternate Capture Input 5
D
PG10/TMR6/TSCLK0A/TACI6
I/O
GPIO/Timer 6 /Sport 0 Alternate Transmit
/Alternate Capture Input 6
D
PG11/TMR7/HOST_WR
I/O
GPIO/Timer7/Host DMA Write Enable
C
PG12/DMAR1/UART1TXA/HOST_ACK
I/O
GPIO/DMA Request 1/Alternate UART1 Transmit/Host DMA Acknowledge
C
PG13/DMAR0/UART1RXA/HOST_ADDR/TACI2
I/O
GPIO/DMA Request 0/Alternate UART1 Receive/Host DMA Address/Alternate
Capture Input 2
C
PG14/TSCLK0A1/MDC/HOST_RD
I/O
GPIO/SPORT0 Alternate 1 Transmit/Ethernet Management Channel Clock
/Host DMA Read Enable
D
PG153/TFS0A/MII PHYINT/RMII MDINT/HOST_CE I/O
GPIO/SPORT0 Alternate Transmit Frame Sync/Ethernet/MII PHY Interrupt/RMII C
Management Channel Data Interrupt/Host DMA Chip Enable
Port H: GPIO and Multiplexed Peripherals
PH0/ND_D0/MIICRS/RMIICRSDV/HOST_D0
I/O
GPIO/NAND D0/Ethernet MII or RMII Carrier Sense/Host DMA D0
C
PH1/ND_D1/ERxER/HOST_D1
I/O
GPIO/NAND D1/Ethernet MII or RMII Receive Error/Host DMA D1
C
PH2/ND_D2/MDIO/HOST_D2
I/O
GPIO/NAND D2/Ethernet Management Channel Serial Data/Host DMA D2
C
PH3/ND_D3/ETxEN/HOST_D3
I/O
GPIO/NAND D3/Ethernet MII Transmit Enable/Host DMA D3
C
PH4/ND_D4/MIITxCLK/RMIIREF_CLK/HOST_D4 I/O
GPIO/NAND D4/Ethernet MII or RMII Reference Clock/Host D4
C
PH5/ND_D5/ETxD0/HOST_D5
I/O
GPIO/NAND D5/Ethernet MII or RMII Transmit D0/Host DMA D5
C
PH6/ND_D6/ERxD0/HOST_D6
I/O
GPIO/NAND D6/Ethernet MII or RMII Receive D0/Host DMA D6
C
PH7/ND_D7/ETxD1/HOST_D7
I/O
GPIO/NAND D7/Ethernet MII or RMII Transmit D1/Host DMA D7
C
PH8/SPISEL4/ERxD1/HOST_D8/TACLK2
I/O
GPIO/Alternate Timer Clock 2/Ethernet MII or RMII Receive D1/Host DMA D8
/SPI Slave Select 4
C
PH9/SPISEL5/ETxD2/HOST_D9/TACLK3
I/O
GPIO/SPI Slave Select 5/Ethernet MII Transmit D2/Host DMA D9
/Alternate Timer Clock 3
C
PH10/ND_CE/ERxD2/HOST_D10
I/O
GPIO/NAND Chip Enable/Ethernet MII Receive D2/Host DMA D10
C
PH11/ND_WE/ETxD3/HOST_D11
I/O
GPIO/NAND Write Enable/Ethernet MII Transmit D3/Host DMA D11
C
PH12/ND_RE/ERxD3/HOST_D12
I/O
GPIO/NAND Read Enable/Ethernet MII Receive D3/Host DMA D12
C
PH13/ND_BUSY/ERxCLK/HOST_D13
I/O
GPIO/NAND Busy/Ethernet MII Receive Clock/Host DMA D13
C
PH14/ND_CLE/ERxDV/HOST_D14
I/O
GPIO/NAND Command Latch Enable/Ethernet MII or RMII Receive Data Valid/ C
Host DMA D14
PH15/ND_ALE/COL/HOST_D15
I/O
GPIO/NAND Address Latch Enable/Ethernet MII Collision/Host DMA Data 15
Rev. D |
Page 25 of 88 | July 2013
C
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 10. Signal Descriptions (Continued)
Type Function
Driver
Type1
I/O
PPI Frame Sync1/Timer0
C
PJ1: PPI_CLK/TMRCLK
I
PPI Clock/Timer Clock
PJ2: SCL
I/O 5V TWI Serial Clock (This pin is an open-drain output and requires a pull-up
resistor.4)
E
PJ3: SDA
I/O 5V TWI Serial Data (This pin is an open-drain output and requires a pull-up
resistor.4)
E
Signal Name
Port J: Multiplexed Peripherals
PJ0: PPI_FS1/TMR0
Real Time Clock
RTXI
I
RTC Crystal Input (This ball should be pulled low when not used.)
RTXO
O
RTC Crystal Output (Does not three-state during hibernate.)
TCK
I
JTAG Clock
TDO
O
JTAG Serial Data Out
TDI
I
JTAG Serial Data In
TMS
I
JTAG Mode Select
TRST
I
JTAG Reset (This ball should be pulled low if the JTAG port is not used.)
EMU
O
Emulation Output
I
Clock/Crystal Input
JTAG Port
C
C
Clock
CLKIN
XTAL
O
Crystal Output (If CLKBUF is enabled, does not three-state during hibernate.)
CLKBUF
O
Buffered XTAL Output (If enabled, does not three-state during hibernate.)
I
Reset
C
Mode Controls
RESET
NMI
I
Nonmaskable Interrupt (This ball should be pulled high when not used.)
BMODE3–0
I
Boot Mode Strap 3-0
VRSEL
I
Internal/External Voltage Regulator Select
VROUT/EXT_WAKE1
O
External FET Drive/Wake up Indication 1 (Does not three-state during
hibernate.)
G
EXT_WAKE0
O
Wake up Indication 0 (Does not three-state during hibernate.)
C
SS/PG
A
Soft Start/Power Good
EXT_WAKE1
O
Wake up Indication 1 (Does not three-state during hibernate.)
C
EXT_WAKE0
O
Wake up Indication 0 (Does not three-state during hibernate.)
C
PG
A
Power Good (This signal should be pulled low when not used.)
ADSP-BF523/ADSP-BF525/ADSP-BF527 Voltage
Regulation I/F
ADSP-BF522/ADSP-BF524/ADSP-BF526 Voltage
Regulation I/F
Rev. D
|
Page 26 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 10. Signal Descriptions (Continued)
Signal Name
Type Function
Driver
Type1
ALL SUPPLIES MUST BE POWERED
See Operating Conditions for ADSP-BF523/ADSP-BF525/ADSP-BF527
Processors on Page 30, and see Operating Conditions for ADSP-BF522/
ADSP-BF524/ADSP-BF526 Processors on Page 28.
Power Supplies
VDDEXT
P
I/O Power Supply
VDDINT
P
Internal Power Supply
VDDRTC
P
Real Time Clock Power Supply
VDDUSB
P
3.3 V USB Phy Power Supply
VDDMEM
P
MEM Power Supply
VDDOTP
P
OTP Power Supply
VPPOTP
P
OTP Programming Voltage
GND
G
Ground for All Supplies
1
See Output Drive Currents on Page 73 for more information about each driver type.
HWAIT must be pulled high or low to configure polarity. It is driven as an output and toggle during processor boot. See Booting Modes on Page 18.
3
When driven low, this ball can be used to wake up the processor from the hibernate state, either in normal GPIO mode or in Ethernet mode as MII PHYINT. If the ball is
used for wake up, enable the feature with the PHYWE bit in the VR_CTL register, and pull-up the ball with a resistor.
4
Consult version 2.1 of the I2C specification for the proper resistor value.
2
Rev. D |
Page 27 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
SPECIFICATIONS
Specifications are subject to change without notice.
OPERATING CONDITIONS
FOR ADSP-BF522/ADSP-BF524/ADSP-BF526 PROCESSORS
Parameter
VDDINT
VDDEXT
VDDEXT
VDDEXT
VDDRTC
VDDMEM
VDDMEM
VDDMEM
VDDOTP
VPPOTP
Conditions
VDDUSB
VIH
VIH
VIH
VIHTWI9
VIL
VIL
VIL
VILTWI
TJ
Internal Supply Voltage
External Supply Voltage1
External Supply Voltage1
External Supply Voltage1
RTC Power Supply Voltage2
MEM Supply Voltage1, 3
MEM Supply Voltage1, 3
MEM Supply Voltage1, 3
OTP Supply Voltage1
OTP Programming Voltage1
For Reads
For Writes4
USB Supply Voltage5
High Level Input Voltage6, 7
High Level Input Voltage6, 8
High Level Input Voltage6, 8
High Level Input Voltage
Low Level Input Voltage6, 7
Low Level Input Voltage6, 8
Low Level Input Voltage6, 8
Low Level Input Voltage
Junction Temperature
TJ
Junction Temperature
TJ
Junction Temperature
Min
1.235
1.7
2.25
3
2.25
1.7
2.25
3
2.25
2.25
6.9
3.0
VDDEXT/VDDMEM = 1.90 V
1.1
VDDEXT/VDDMEM = 2.75 V
1.7
VDDEXT/VDDMEM = 3.6 V
2.0
VDDEXT = 1.90 V/2.75 V/3.6 V 0.7 × VBUSTWI
VDDEXT/VDDMEM = 1.7 V
VDDEXT/VDDMEM = 2.25 V
VDDEXT/VDDMEM = 3.0 V
VDDEXT = Minimum
0
289-Ball CSP_BGA
@ TAMBIENT = 0°C to +70°C
0
208-Ball CSP_BGA
@ TAMBIENT = 0°C to +70°C
–40
208-Ball CSP_BGA
@ TAMBIENT = –40°C to +85°C
1
Nominal
1.8
2.5
3.3
2.5
Max
1.47
1.9
2.75
3.6
3.6
1.9
2.75
3.6
2.75
Unit
V
V
V
V
V
V
V
V
V
2.5
7.0
3.3
2.75
7.1
3.6
VBUSTWI
0.6
0.7
0.8
0.3 × VBUSTWI10
+105
V
V
V
V
V
V
V
V
V
V
V
°C
+105
°C
+105
°C
1.8
2.5
3.3
Must remain powered (even if the associated function is not used).
If not used, power with VDDEXT.
3
Balls that use VDDMEM are DATA15–0, ADDR19–1, ABE1–0, ARE, AWE, AOE, AMS3–0, ARDY, SA10, SWE, SCAS, CLKOUT, SRAS, SMS, SCKE. These balls are not tolerant
to voltages higher than VDDMEM.
4
The VPPOTP voltage for writes must only be applied when programming OTP memory. There is a finite amount of cumulative time that this voltage may be applied (dependent
on voltage and junction temperature) over the lifetime of the part. Please see Table 30 on Page 38 for details.
5
When not using the USB peripheral on the ADSP-BF524/ADSP-BF526 or terminating VDDUSB on the ADSP-BF522, VDDUSB must be powered by VDDEXT.
6
Parameter value applies to all input and bidirectional balls, except USB_DP, USB_DM, USB_VBUS, SDA, and SCL.
7
Bidirectional balls (PF15–0, PG15–0, PH15–0) and input balls (RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET, NMI, and BMODE3–0) of the ADSP-BF52x processors are
2.5 V tolerant (always accept up to 2.7 V maximum VIH). Voltage compliance (on outputs, VOH) is limited by the VDDEXT supply voltage.
8
Bidirectional balls (PF15–0, PG15–0, PH15–0) and input balls (RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET, NMI, and BMODE3–0) of the ADSP-BF52x processors are
3.3 V tolerant (always accept up to 3.6 V maximum VIH). Voltage compliance (on outputs, VOH) is limited by the VDDEXT supply voltage.
9
The VIHTWI min and max value vary with the selection in the TWI_DT field of the NONGPIO_DRIVE register. See VBUSTWI min and max values in Table 11.
10
SDA and SCL are pulled up to VBUSTWI. See Table 11.
2
Rev. D
|
Page 28 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 11 shows settings for TWI_DT in the NONGPIO_DRIVE
register. Set this register prior to using the TWI port.
Table 11. TWI_DT Field Selections and VDDEXT/VBUSTWI
TWI_DT
000 (default)1
001
010
011
100
101
110
111 (reserved)
1
VDDEXT Nominal
3.3
1.8
2.5
1.8
3.3
1.8
2.5
–
VBUSTWI Min
2.97
1.7
2.97
2.97
4.5
2.25
2.25
–
VBUSTWI Nominal
3.3
1.8
3.3
3.3
5
2.5
2.5
–
VBUSTWI Max
3.63
1.98
3.63
3.63
5.5
2.75
2.75
–
Unit
V
V
V
V
V
V
V
–
Designs must comply with the VDDEXT and VBUSTWI voltages specified for the default TWI_DT setting for correct JTAG boundary scan operation during reset.
Clock Related Operating Conditions
for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
Table 12 describes the core clock timing requirements for the
ADSP-BF522/ADSP-BF524/ADSP-BF526 processors. Take care
in selecting MSEL, SSEL, and CSEL ratios so as not to exceed the
maximum core clock and system clock (see Table 14). Table 13
describes phase-locked loop operating conditions.
Table 12. Core Clock (CCLK) Requirements (All Instruction Rates1) for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
Parameter
fCCLK
fCCLK
1
2
Core Clock Frequency (VDDINT =1.33 V minimum)
Core Clock Frequency (VDDINT = 1.235 V minimum)
Nominal Voltage Setting
1.40 V
1.30 V
Max
4002
300
Unit
MHz
MHz
See the Ordering Guide on Page 88.
Applies to 400 MHz models only. See the Ordering Guide on Page 88.
Table 13. Phase-Locked Loop Operating Conditions for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
Parameter
fVCO
1
Voltage Controlled Oscillator (VCO) Frequency
Min
70
Max
Instruction Rate1
Unit
MHz
VDDEXT/VDDMEM
2.5 V or 3.3 V Nominal
Max
100
80
Unit
MHz
MHz
See the Ordering Guide on Page 88.
Table 14. SCLK Conditions for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
VDDEXT/VDDMEM
1.8 V Nominal1
Parameter
fSCLK
fSCLK
1
2
CLKOUT/SCLK Frequency (VDDINT ≥ 1.33 V)2
CLKOUT/SCLK Frequency (VDDINT < 1.33 V)
Max
80
80
If either VDDEXT or VDDMEM are operating at 1.8 V nominal, fSCLK is constrained to 80 MHz.
fSCLK must be less than or equal to fCCLK and is subject to additional restrictions for SDRAM interface operation. See Table 37 on Page 47.
Rev. D |
Page 29 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
OPERATING CONDITIONS FOR ADSP-BF523/ADSP-BF525/ADSP-BF527 PROCESSORS
Parameter
VDDINT
VDDINT
Internal Supply Voltage1
Internal Supply Voltage1
VDDINT
VDDEXT
Internal Supply Voltage1
External Supply Voltage4, 5
VDDEXT
VDDEXT
VDDEXT
VDDRTC
VDDRTC
VDDMEM
VDDMEM
VDDMEM
VDDMEM
VDDOTP
VPPOTP
VDDUSB
VIH
VIH
VIH
VIHTWI
VIL
VIL
VIL
VILTWI
TJ
External Supply Voltage4, 5
External Supply Voltage4, 5
External Supply Voltage4, 5
RTC Power Supply Voltage6
RTC Power Supply Voltage6
MEM Supply Voltage4, 7
MEM Supply Voltage4, 7
MEM Supply Voltage4, 7
MEM Supply Voltage4, 7
OTP Supply Voltage4
OTP Programming Voltage4
USB Supply Voltage8
High Level Input Voltage9, 10
High Level Input Voltage10, 11
High Level Input Voltage10, 11
High Level Input Voltage12
Low Level Input Voltage9, 10
Low Level Input Voltage10, 11
Low Level Input Voltage10, 11
Low Level Input Voltage
Junction Temperature
TJ
Junction Temperature
TJ
Junction Temperature
TJ
Junction Temperature
Conditions
Min
Nonautomotive models2
0.95
Automotive 533 MHz models3 1.093
Automotive 400 MHz models3
Nonautomotive models,
Internal Voltage Regulator
Disabled
Nonautomotive models
Nonautomotive models
Automotive models
Nonautomotive models
Automotive models
Nonautomotive models
Nonautomotive models
Nonautomotive models
Automotive models
VDDEXT/VDDMEM = 1.90 V
VDDEXT/VDDMEM = 2.75 V
VDDEXT/VDDMEM = 3.6 V
VDDEXT = 1.90 V/2.75 V/3.6 V
VDDEXT/VDDMEM = 1.7 V
VDDEXT/VDDMEM = 2.25 V
VDDEXT/VDDMEM = 3.0 V
VDDEXT = Minimum
289-Ball CSP_BGA
@ TAMBIENT = 0°C to +70°C
289-Ball CSP_BGA
@ TAMBIENT = –40°C to +70°C
208-Ball CSP_BGA
@ TAMBIENT = 0°C to +70°C
208-Ball CSP_BGA
@ TAMBIENT = –40°C to +85°C
1.15
Max
1.26
1.26
1.045
1.7
1.10
1.8
1.20
1.9
V
V
2.25
3
2.7
2.25
2.7
1.7
2.25
3
2.7
2.25
2.25
3.0
1.1
1.7
2.0
0.7 × VBUSTWI
2.5
3.3
3.3
2.75
3.6
3.6
3.6
3.6
1.9
2.75
3.6
3.6
2.75
2.75
3.6
0
VBUSTWI
0.6
0.7
0.8
0.3 × VBUSTWI13
+105
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
°C
–40
+105
°C
0
+105
°C
–40
+105
°C
1
Nominal
3.3
1.8
2.5
3.3
3.3
2.5
2.5
3.3
Unit
V
V
The voltage regulator can generate VDDINT at levels of 1.00 V to 1.20 V with –5% to +5% tolerance when VRCTL is programmed with the bfrom_SysControl() API. This
specification is only guaranteed when the API is used.
See Ordering Guide on Page 88.
3
See Automotive Products on Page 87.
4
Must remain powered (even if the associated function is not used).
5
VDDEXT is the supply to the voltage regulator and GPIO.
6
If not used, power with VDDEXT.
7
Balls that use VDDMEM are DATA15–0, ADDR19–1, ABE1–0, ARE, AWE, AOE, AMS3–0, ARDY, SA10, SWE, SCAS, CLKOUT, SRAS, SMS, SCKE. These balls are not tolerant
to voltages higher than VDDMEM.
8
When not using the USB peripheral on the ADSP-BF525/ADSP-BF527 or terminating VDDUSB on the ADSP-BF523, VDDUSB must be powered by VDDEXT.
9
Bidirectional balls (PF15–0, PG15–0, PH15–0) and input balls (RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET, NMI, and BMODE3–0) of the ADSP-BF52x processors are
2.5 V tolerant (always accept up to 2.7 V maximum VIH). Voltage compliance (on outputs, VOH) is limited by the VDDEXT supply voltage.
10
Parameter value applies to all input and bidirectional balls, except USB_DP, USB_DM, USB_VBUS, SDA, and SCL.
11
Bidirectional balls (PF15–0, PG15–0, PH15–0) and input balls (RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET, NMI, and BMODE3–0) of the ADSP-BF52x processors are
3.3 V tolerant (always accept up to 3.6 V maximum VIH). Voltage compliance (on outputs, VOH) is limited by the VDDEXT supply voltage.
12
The VIHTWI min and max value vary with the selection in the TWI_DT field of the NONGPIO_DRIVE register. See VBUSTWI min and max values in Table 11 on Page 29.
13
SDA and SCL are pulled up to VBUSTWI. See Table 11 on Page 29.
2
Rev. D
|
Page 30 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Clock Related Operating Conditions
for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
Table 15 describes the core clock timing requirements for the
ADSP-BF523/ADSP-BF525/ADSP-BF527 processors. Take care
in selecting MSEL, SSEL, and CSEL ratios so as not to exceed the
maximum core clock and system clock (see Table 17). Table 16
describes phase-locked loop operating conditions.
Use the nominal voltage setting (Table 15) for internal and
external regulators.
Table 15. Core Clock (CCLK) Requirements (All Instruction Rates1) for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
Parameter
fCCLK
fCCLK
fCCLK
fCCLK
Core Clock Frequency (VDDINT =1.14 V minimum)
Core Clock Frequency (VDDINT =1.093 V minimum)
Core Clock Frequency (VDDINT = 1.045 V minimum)4
Core Clock Frequency (VDDINT = 0.95 V minimum)
Nominal Voltage Setting
1.20 V
1.15 V
1.10 V
1.0 V
Max
6002
5333
400
400
Unit
MHz
MHz
MHz
MHz
1
See the Ordering Guide on Page 88.
Applies to 600 MHz models only. See the Ordering Guide on Page 88.
3
Applies to 533 MHz and 600 MHz models only. See the Ordering Guide on Page 88.
4
Applies only to automotive products. See Automotive Products on Page 87.
2
Table 16. Phase-Locked Loop Operating Conditions for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
Parameter
fVCO
fVCO
1
Voltage Controlled Oscillator (VCO) Frequency
(Commercial/Industrial Models)
Voltage Controlled Oscillator (VCO) Frequency
(Automotive Models)
Min
60
Max
Instruction Rate1
Unit
MHz
70
Instruction Rate1
MHz
VDDEXT/VDDMEM
2.5 V or 3.3 V Nominal
Max
1333
100
Unit
MHz
MHz
See the Ordering Guide on Page 88.
Table 17. SCLK Conditions for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
VDDEXT/VDDMEM
1.8 V Nominal1
Parameter
fSCLK
fSCLK
2
CLKOUT/SCLK Frequency (VDDINT ≥ 1.14 V)
CLKOUT/SCLK Frequency (VDDINT < 1.14 V)2
Max
100
100
1
If either VDDEXT or VDDMEM are operating at 1.8 V nominal, fSCLK is constrained to 100 MHz.
fSCLK must be less than or equal to fCCLK and is subject to additional restrictions for SDRAM interface operation. See Table 38 on Page 47.
3
Rounded number. Actual test specification is SCLK period of 7.5 ns. See Table 38 on Page 47.
2
Rev. D |
Page 31 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
ELECTRICAL CHARACTERISTICS
Table 18. Common Electrical Characteristics for All ADSP-BF52x Processors
Parameter
Test Conditions
Min
Typical
Max
Unit
VOH
High Level Output Voltage
VDDEXT /VDDMEM = 1.7 V,
IOH = –0.5 mA
1.35
V
VOH
High Level Output Voltage
VDDEXT /VDDMEM = 2.25 V,
IOH = –0.5 mA
2.0
V
VOH
High Level Output Voltage
VDDEXT /VDDMEM = 3.0 V,
IOH = –0.5 mA
2.4
V
VOL
Low Level Output Voltage
VDDEXT /VDDMEM = 1.7 V/2.25 V/
3.0 V,
IOL = 2.0 mA
0.4
V
IIH
High Level Input Current1
VDDEXT /VDDMEM =3.6 V,
VIN = 3.6 V
10.0
μA
IIL
Low Level Input Current1
VDDEXT /VDDMEM =3.6 V, VIN = 0 V
10.0
μA
75.0
μA
IIHP
2
High Level Input Current JTAG VDDEXT = 3.6 V, VIN = 3.6 V
3
IOZH
Three-State Leakage Current VDDEXT /VDDMEM= 3.6 V,
VIN = 3.6 V
10.0
μA
IOZHTWI
Three-State Leakage Current4 VDDEXT =3.0 V, VIN = 5.5 V
10.0
μA
10.0
μA
8
pF
15
pF
IOZL
3
Three-State Leakage Current VDDEXT /VDDMEM= 3.6 V, VIN = 0 V
CIN
Input Capacitance
5,6
fIN = 1 MHz, TAMBIENT = 25°C,
VIN = 2.5 V
CINTWI
Input Capacitance4,6
fIN = 1 MHz, TAMBIENT = 25°C,
VIN = 2.5 V
1
Applies to input balls.
Applies to JTAG input balls (TCK, TDI, TMS, TRST).
3
Applies to three-statable balls.
4
Applies to bidirectional balls SCL and SDA.
5
Applies to all signal balls, except SCL and SDA.
6
Guaranteed, but not tested.
2
Rev. D
|
Page 32 of 88 | July 2013
5
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 19. Electrical Characteristics for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
Parameter
1
Test Conditions
Min
Typical
Max
Unit
VDDINT Current in VDDINT = 1.3 V, fCCLK = 0 MHz, fSCLK = 0 MHz,
Deep Sleep Mode TJ = 25°C, ASF = 0.00
2
mA
IDDSLEEP
VDDINT Current in
Sleep Mode
VDDINT = 1.3 V, fSCLK = 25 MHz, TJ = 25°C
13
mA
IDD-IDLE
VDDINT Current in
Idle
VDDINT = 1.3 V, fCCLK = 300 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 0.4
44
mA
IDD-TYP
VDDINT Current
VDDINT = 1.3 V, fCCLK = 300 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 1.00
83
mA
IDD-TYP
VDDINT Current
VDDINT = 1.4 V, fCCLK = 400 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 1.00
114
mA
IDDHIBERNATE1, 2
Hibernate State
Current
VDDEXT =VDDMEM =VDDRTC =VDDUSB = 3.30 V,
VDDOTP =VPPOTP =2.5 V, TJ = 25°C, CLKIN = 0 MHz
with voltage regulator off (VDDINT = 0 V)
40
μA
IDDRTC
VDDRTC Current
VDDRTC = 3.3 V, TJ = 25°C
20
μA
IDDUSB-FS
VDDUSB Current in
Full/Low Speed
Mode
VDDUSB = 3.3 V, TJ = 25°C, Full Speed USB Transmit
9
mA
IDDUSB-HS
VDDUSB Current in VDDUSB = 3.3 V, TJ = 25°C, High Speed USB Transmit
High Speed Mode
25
mA
IDDSLEEP1, 3
VDDINIT Current in
Sleep Mode
IDDDEEPSLEEP1, 3
VDDINT Current in fCCLK = 0 MHz, fSCLK = 0 MHz
Deep Sleep Mode
Table 22
IDDINT3, 5
VDDINT Current
fCCLK > 0 MHz, fSCLK ≥ 0 MHz
mA
Table 22 +
(Table 23 × ASF) +
(0.52 × VDDINT × fSCLK)
IDDOTP
VDDOTP Current
VDDOTP = 2.5 V, TJ = 25°C, OTP Memory Read
2
mA
IDDOTP
VDDOTP Current
VDDOTP = 2.5 V, TJ = 25°C, OTP Memory Write
2
mA
IPPOTP
VPPOTP Current
VPPOTP = 2.5 V, TJ = 25°C, OTP Memory Read
100
μA
IPPOTP
VPPOTP Current
VPPOTP = see Table 30, TJ = 25°C, OTP Memory
Write
3
mA
IDDDEEPSLEEP
Table 22 +
mA4
4
(0.52 × VDDINT × fSCLK)
fCCLK = 0 MHz, fSCLK > 0 MHz
1
See the ADSP-BF52x Blackfin Processor Hardware Reference Manual for definition of sleep, deep sleep, and hibernate operating modes.
Includes current on VDDEXT, VDDUSB, VDDMEM, VDDOTP, and VPPOTP supplies. Clock inputs are tied high or low.
3
Guaranteed maximum specifications.
4
Unit for VDDINT is V (Volts). Unit for fSCLK is MHz. Example: 1.4 V, 75 MHz would be 0.52 × 1.4 × 75 = 54.6 mA adder.
5
See Table 21 for the list of IDDINT power vectors covered.
2
Rev. D |
Page 33 of 88 | July 2013
mA
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 20. Electrical Characteristics for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
Parameter
1
Test Conditions
Min
Typical
Max
Unit
VDDINT Current in VDDINT = 1.0 V, fCCLK = 0 MHz, fSCLK = 0 MHz,
Deep Sleep Mode TJ = 25°C, ASF = 0.00
10
mA
IDDSLEEP
VDDINT Current in
Sleep Mode
VDDINT = 1.0 V, fSCLK = 25 MHz, TJ = 25°C
20
mA
IDD-IDLE
VDDINT Current in
Idle
VDDINT = 1.0 V, fCCLK = 400 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 0.44
53
mA
IDD-TYP
VDDINT Current
VDDINT = 1.0 V, fCCLK = 400 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 1.00
94
mA
IDD-TYP
VDDINT Current
VDDINT = 1.15 V, fCCLK = 533 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 1.00
144
mA
IDD-TYP
VDDINT Current
VDDINT = 1.2 V, fCCLK = 600 MHz, fSCLK = 25 MHz,
TJ = 25°C, ASF = 1.00
170
mA
IDDHIBERNATE1, 2
Hibernate State
Current
VDDEXT =VDDMEM =VDDRTC = VDDUSB = 3.30 V,
VDDOTP =VPPOTP =2.5 V, TJ = 25°C, CLKIN = 0 MHz
with voltage regulator off (VDDINT = 0 V)
40
μA
IDDRTC
VDDRTC Current
VDDRTC = 3.3 V, TJ = 25°C
20
μA
IDDUSB-FS
VDDUSB Current in
Full/Low Speed
Mode
VDDUSB = 3.3 V, TJ = 25°C, Full Speed USB Transmit
9
mA
IDDUSB-HS
VDDUSB Current in VDDUSB = 3.3 V, TJ = 25°C, High Speed USB
High Speed Mode Transmit
25
mA
IDDSLEEP1, 3
VDDINT Current in
Sleep Mode
IDDDEEPSLEEP1, 3
IDDDEEPSLEEP
Table 24 + (0.61 ×
VDDINT × fSCLK)4
mA4
VDDINT Current in fCCLK = 0 MHz, fSCLK = 0 MHz
Deep Sleep Mode
Table 24
mA
IDDINT3, 5
VDDINT Current
fCCLK > 0 MHz, fSCLK ≥ 0 MHz
Table 24 + (Table 25 mA
× ASF) + (0.61 × VDDINT
× fSCLK)
IDDOTP
VDDOTP Current
VDDOTP = 2.5 V, TJ = 25°C, OTP Memory Read
IDDOTP
VDDOTP Current
VDDOTP = 2.5 V, TJ = 25°C, OTP Memory Write
25
mA
IPPOTP
VPPOTP Current
VPPOTP = 2.5 V, TJ = 25°C, OTP Memory Read
0
mA
IPPOTP
VPPOTP Current
VPPOTP = 2.5 V, TJ = 25°C, OTP Memory Write
0
mA
fCCLK = 0 MHz, fSCLK > 0 MHz
1
1
See the ADSP-BF52x Blackfin Processor Hardware Reference Manual for definition of sleep, deep sleep, and hibernate operating modes.
Includes current on VDDEXT, VDDUSB, VDDMEM, VDDOTP, and VPPOTP supplies. Clock inputs are tied high or low.
3
Guaranteed maximum specifications.
4
Unit for VDDINT is V (Volts). Unit for fSCLK is MHz. Example: 1.2 V, 75 MHz would be 0.61 × 1.2 × 75 = 54.9 mA adder.
5
See Table 21 for the list of IDDINT power vectors covered.
2
Rev. D
|
Page 34 of 88 | July 2013
mA
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Total Power Dissipation
Total power dissipation has two components:
1. Static, including leakage current
2. Dynamic, due to transistor switching characteristics
Many operating conditions can also affect power dissipation,
including temperature, voltage, operating frequency, and processor activity. Electrical Characteristics on Page 32 shows the
current dissipation for internal circuitry (VDDINT). IDDDEEPSLEEP
specifies static power dissipation as a function of voltage
(VDDINT) and temperature (see Table 22 or Table 24), and IDDINT
specifies the total power specification for the listed test conditions, including the dynamic component as a function of voltage
(VDDINT) and frequency (Table 23 or Table 25).
There are two parts to the dynamic component. The first part is
due to transistor switching in the core clock (CCLK) domain.
This part is subject to an Activity Scaling Factor (ASF) which
represents application code running on the processor core and
L1 memories (Table 21).
The ASF is combined with the CCLK Frequency and VDDINT
dependent data in Table 23 or Table 25 to calculate this part.
The second part is due to transistor switching in the system
clock (SCLK) domain, which is included in the IDDINT specification equation.
Table 21. Activity Scaling Factors (ASF)1
IDDINT Power Vector
IDD-PEAK
IDD-HIGH
IDD-TYP
IDD-APP
IDD-NOP
IDD-IDLE
1
Activity Scaling Factor (ASF)
1.29
1.26
1.00
0.88
0.72
0.44
See Estimating Power for ASDP-BF534/BF536/BF537 Blackfin Processors
(EE-297). The power vector information also applies to the ADSP-BF52x
processors.
Table 22. Static Current — IDD-DEEPSLEEP (mA) for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
1
TJ (°C)
–40
–20
0
25
40
55
70
85
100
105
1
1.2 V
1.47
1.67
1.97
2.49
3.12
4.07
5.77
8.32
12.11
13.78
1.25 V
1.42
1.81
2.07
2.66
3.37
4.47
6.28
8.88
12.93
14.72
1.3 V
1.50
1.89
2.15
2.79
3.57
4.82
6.71
9.56
13.94
15.74
Voltage (VDDINT)1
1.35 V
1.4 V
1.64
1.85
1.95
2.01
2.22
2.30
2.92
3.07
3.75
3.96
5.11
5.41
7.17
7.61
10.25
10.94
14.76
15.76
16.81
17.91
1.45 V
2.12
2.07
2.39
3.20
4.18
5.73
8.09
11.63
16.77
19.06
1.5 V
2.09
2.12
2.47
3.36
4.40
6.06
8.60
12.36
17.83
20.27
Valid temperature and voltage ranges are model-specific. See Operating Conditions for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors on Page 28.
Table 23. Dynamic Current in CCLK Domain (mA, with ASF = 1.0)1 for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
fCCLK
(MHz)2
400
350
300
250
200
100
1
2
1.2 V
N/A
N/A
63.31
53.36
43.49
23.6
1.25 V
N/A
N/A
66.51
56.10
45.76
24.93
1.3 V
91.41
80.56
69.78
58.88
48.08
26.29
Voltage (VDDINT)2
1.35 V
1.4 V
95.7
100.11
84.37
88.26
73.09
76.51
61.72
64.64
50.44
52.86
27.68
29.12
1.45 V
104.51
92.17
79.93
67.56
55.28
30.56
1.5 V
109.01
96.17
83.42
70.55
57.77
32.04
The values are not guaranteed as standalone maximum specifications. They must be combined with static current per the equations of Electrical Characteristics on Page 32.
Valid frequency and voltage ranges are model-specific. See Operating Conditions for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors on Page 28.
Rev. D |
Page 35 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 24. Static Current — IDD-DEEPSLEEP (mA) for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
1
TJ (°C)
–40
–20
0
25
40
55
70
85
100
105
115
125
1
0.95 V
6.5
9.0
13.2
22.3
30.8
42.9
59.1
80.4
109.3
120.8
144.4
173.9
1.00 V
7.8
10.6
15.2
25.4
34.8
47.9
65.6
88.6
118.7
132.1
157.5
189.1
Voltage (VDDINT)1
1.10 V
1.15 V
11.1
13.1
14.6
17.0
20.4
23.5
32.8
37.2
44.1
49.6
59.9
66.9
80.8
89.7
107.8
119.2
143.2
157.4
158.8
174.2
188.4
206.0
224.9
245.4
1.05 V
9.3
12.4
17.7
28.9
39.2
53.6
72.9
97.9
130.5
144.7
172.3
206.4
1.20 V
15.4
19.8
27.0
42.1
55.7
74.6
99.4
131.5
172.8
190.9
225.3
267.8
1.25 V
18.0
22.9
30.9
47.6
62.5
83.2
110.2
145.1
189.7
209.3
246.4
292.2
1.30 V
21.0
26.4
35.3
53.7
70.0
92.6
122.0
159.8
208.1
229.2
269.2
318.7
Valid temperature and voltage ranges are model-specific. See Operating Conditions for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors on Page 30.
Table 25. Dynamic Current in CCLK Domain (mA, with ASF = 1.0)1 for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
fCCLK
(MHz)2
600
533
500
400
300
200
100
1
2
0.95 V
N/A
N/A
N/A
69.8
53.4
36.9
20.5
1.00 V
N/A
N/A
N/A
74.3
56.9
39.4
22.0
Voltage (VDDINT)2
1.10 V
1.15 V
N/A
130.4
110.3
116.7
103.1
109.1
83.6
88.5
64.1
68.0
44.6
47.4
25.3
27.0
1.05 V
N/A
N/A
97.3
78.9
60.4
41.9
23.6
1.20 V
137.6
123.3
115.0
93.5
71.8
50.1
28.8
1.25 V
145.1
129.8
121.3
98.6
75.8
53.0
30.6
1.30 V
152.5
136.4
127.7
103.9
80.0
56.0
32.5
The values are not guaranteed as standalone maximum specifications. They must be combined with static current per the equations of Electrical Characteristics on Page 32.
Valid frequency and voltage ranges are model-specific. See Operating Conditions for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors on Page 30.
Rev. D
|
Page 36 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
ABSOLUTE MAXIMUM RATINGS
Stresses greater than those listed in Table 26 may cause permanent damage to the device. These are stress ratings only.
Functional operation of the device at these or any other condi-
tions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
Table 26. Absolute Maximum Ratings
Parameter
Rating
Internal Supply Voltage (VDDINT) for ADSP-BF523/ADSP-BF525/ADSP-BF527 processors
–0.3 V to +1.26 V
Internal Supply Voltage (VDDINT) for ADSP-BF522/ADSP-BF524/ADSP-BF526 processors
–0.3 V to +1.47 V
External (I/O) Supply Voltage (VDDEXT/VDDMEM)
–0.3 V to +3.8 V
Real-Time Clock Supply Voltage (VDDRTC)
–0.5 V to +3.8 V
OTP Supply Voltage (VDDOTP)
–0.5 V to +3.0 V
OTP Programming Voltage (VPPOTP)1
–0.5 V to +3.0 V
OTP Programming Voltage (VPPOTP)2
–0.5 V to +7.1 V
USB PHY Supply Voltage (VDDUSB)
–0.5 V to +3.8 V
Input Voltage3, 4, 5
–0.5 V to +3.8 V
Input Voltage3, 4, 6
–0.5 V to +5.5 V
Input Voltage
3, 4, 7
–0.5 V to +5.25 V
Output Voltage Swing
–0.5 V to VDDEXT /VDDMEM + 0.5 V
IOH/IOL Current per Pin Group
3, 8
82 mA (max)
Storage Temperature Range
–65°C to +150°C
Junction Temperature While Biased
+110°C
1
Applies to OTP memory reads and writes for ADSP-BF523/ADSP-BF525/ADSP-BF527 processors and to OTP memory reads for ADSP-BF522/ADSP-BF524/ADSP-BF526
processors.
Applies only to OTP memory writes for ADSP-BF522/ADSP-BF524/ADSP-BF526 processors.
3
Applies to 100% transient duty cycle.
4
Applies only when VDDEXT is within specifications. When VDDEXT is outside specifications, the range is VDDEXT ±0.2 V.
5
For other duty cycles see Table 27.
6
Applies to balls SCL and SDA.
7
Applies to balls USB_DP, USB_DM, and USB_VBUS.
8
For pin group information, see Table 28. For other duty cycles see Table 29.
2
Table 27. Maximum Duty Cycle for Input Transient Voltage1, 2
Maximum Duty Cycle3
VIN Min (V)4
VIN Max (V)6
100%
–0.50
+3.80
40%
–0.70
+4.00
25%
–0.80
+4.10
15%
–0.90
+4.20
10%
–1.00
+4.30
1
Applies to all signal balls with the exception of CLKIN, XTAL, VROUT/
EXT_WAKE1, SCL, SDA, USB_DP, USB_DM, and USB_VBUS.
2
Applies only when VDDEXT is within specifications. When VDDEXT is outside specifications, the range is VDDEXT ±0.2 V.
3
Duty cycle refers to the percentage of time the signal exceeds the value for the 100%
case. The is equivalent to the measured duration of a single instance of overshoot
or undershoot as a percentage of the period of occurrence.
4
The individual values cannot be combined for analysis of a single instance of
overshoot or undershoot. The worst case observed value must fall within one of the
voltages specified, and the total duration of the overshoot or undershoot (exceeding
the 100% case) must be less than or equal to the corresponding duty cycle.
Rev. D |
Table 26 specifies the maximum total source/sink (IOH/IOL) current for a group of pins. Permanent damage can occur if this
value is exceeded. To understand this specification, if pins PH4,
PH3, PH2, PH1, and PH0 from group 1 in Table 28 were sourcing or sinking 2 mA each, the total current for those pins would
be 10 mA. This would allow up to 72 mA total that could be
sourced or sunk by the remaining pins in the group without
damaging the device. For a list of all groups and their pins, see
the Table 28 table. For duty cycles that are less than 100%, see
Table 29. Note that the VOH and VOL specifications have separate
per-pin maximum current requirements (see Table 19 on
Page 33 and Table 20 on Page 34).
Table 28. Total Current Pin Groups
Group
1
2
3
4
5
Pins in Group
PH4, PH3, PH2, PH1, PH0, PF15, PF14, PF13
PF12, SDA, SCL, PF11, PF10, PF9, PF8, PF7
PF6, PF5, PF4, PF3, PF2, PF1, PF0, PPI_FS1
PPI_CLK, PG15, PG14, PG13, PG12, PG11, PG10, PG9
PG8, PG7, PG6, PG5, PG4, BMODE3, BMODE2, BMODE1
Page 37 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
PACKAGE INFORMATION
Table 28. Total Current Pin Groups (Continued)
Group
6
7
8
9
10
11
12
13
14
15
16
17
18
The information presented in Figure 8 and Table 31 provides
details about the package branding for the ADSP-BF52x processors. For a complete listing of product availability, see Ordering
Guide on Page 88.
Pins in Group
BMODE0, PG3, PG2, PG1, PG0, TDI, TDO, EMU
TCK, TRST, TMS
PH12, PH11, PH10, PH9, PH8, PH7, PH6, PH5
PH15, PH14, PH13, CLKBUF, NMI, RESET
DATA15, DATA14, DATA13, DATA12, DATA11, DATA10
DATA9, DATA8, DATA7, DATA6, DATA5, DATA4
DATA3, DATA2, DATA1, DATA0, ADDR19, ADDR18
ADDR17, ADDR16, ADDR15, ADDR14, ADDR13
ADDR12, ADDR11, ADDR10, ADDR9, ADDR8, ADDR7
ADDR6, ADDR5, ADDR4, ADDR3, ADDR2, ADDR1
ABE1, ABE0, SA10, SWE, SCAS, SRAS
SMS, SCKE, ARDY, AWE, ARE, AOE
AMS3, AMS2, AMS1, AMS0, CLKOUT
a
ADSP-BF52x
tppZccc
vvvvvv.x n.n
#yyww country_of_origin
B
Figure 8. Product Information on Package
Table 31. Package Brand Information1
Table 29. Maximum Duty Cycle for IOH/IOL Current Per Pin
Group
Brand Key
Field Description
ADSP-BF52x
Product Name2
Maximum Duty Cycle
RMS Current (mA)
t
Temperature Range
100%
82
pp
Package Type
80%
92
Z
Lead Free Option
60%
106
ccc
See Ordering Guide
40%
130
vvvvvv.x
Assembly Lot Code
25%
165
n.n
Silicon Revision
261
#
RoHS Compliance Designator
yyww
Date Code
10%
When programming OTP memory on the ADSP-BF522/
ADSP-BF524/ADSP-BF526 processors, the VPPOTP ball must
be set to the write value specified in the Operating Conditions
for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors on
Page 28. There is a finite amount of cumulative time that the
write voltage may be applied (dependent on voltage and junction temperature) to VPPOTP over the lifetime of the part.
Therefore, maximum OTP memory programming time for the
ADSP-BF522/ADSP-BF524/ADSP-BF526 processors is shown
in Table 30. The ADSP-BF523/ADSP-BF525/ADSP-BF527 processors do not have a similar restriction.
1
Non Automotive only. For branding information specific to Automotive
products, contact Analog Devices Inc.
2
See product names in the Ordering Guide on Page 88.
ESD SENSITIVITY
Table 30. Maximum OTP Memory Programming Time for
ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
Temperature (TJ)
VPPOTP Voltage (V)
25°C
85°C
105°C
6.9
6000 sec
100 sec
25 sec
7.0
2400 sec
44 sec
12 sec
7.1
1000 sec
18 sec
4.5 sec
Rev. D
|
Page 38 of 88 | July 2013
ESD (electrostatic discharge) sensitive device.
Charged devices and circuit boards can discharge
without detection. Although this product features
patented or proprietary protection circuitry, damage
may occur on devices subjected to high energy ESD.
Therefore, proper ESD precautions should be taken to
avoid performance degradation or loss of functionality.
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
TIMING SPECIFICATIONS
Specifications are subject to change without notice.
Clock and Reset Timing
Table 32 and Figure 9 describe clock and reset operations. Per
the CCLK and SCLK timing specifications in Table 12 to
Table 17, combinations of CLKIN and clock multipliers must
not select core/peripheral clocks in excess of the processor's
maximum instruction rate.
Table 32. Clock and Reset Timing
Parameter
Min
Max
Unit
50
MHz
50
MHz
Timing Requirements
fCKIN
CLKIN Frequency (Commercial/ Industrial Models) 1, 2, 3, 4 12
CLKIN Frequency (Automotive Models)
1
tCKINL
CLKIN Low Pulse
tCKINH
CLKIN High Pulse1
tWRST
1, 2, 3, 4
RESET Asserted Pulse Width Low
5
14
10
ns
10
ns
11 × tCKIN
ns
Switching Characteristic
tBUFDLAY
CLKIN to CLKBUF Delay
10
ns
1
Applies to PLL bypass mode and PLL nonbypass mode.
Combinations of the CLKIN frequency and the PLL clock multiplier must not exceed the allowed fVCO, fCCLK, and fSCLK settings discussed in Table 12 on Page 29 through
Table 14 on Page 29 and Table 15 on Page 31 through Table 17 on Page 31.
3
The tCKIN period (see Figure 9) equals 1/fCKIN.
4
If the DF bit in the PLL_CTL register is set, the minimum fCKIN specification is 24 MHz for commercial/industrial models and 28 MHz for automotive models.
5
Applies after power-up sequence is complete. See Table 33 and Figure 10 for power-up reset timing.
2
tCKIN
CLKIN
tCKINL
tBUFDLAY
tCKINH
CLKBUF
tWRST
RESET
Figure 9. Clock and Reset Timing
Rev. D |
Page 39 of 88 | July 2013
tBUFDLAY
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 33. Power-Up Reset Timing
Parameter
Min
Max
Unit
Timing Requirement
tRST_IN_PWR
RESET Deasserted after the VDDINT, VDDEXT, VDDRTC, VDDUSB, VDDMEM, VDDOTP, and CLKIN 3500 × tCKIN
Pins are Stable and Within Specification
tRST_IN_PWR
RESET
CLKIN
V
DD_SUPPLIES
In Figure 10, VDD_SUPPLIES is VDDINT, VDDEXT, VDDRTC, VDDUSB, VDDMEM, and VDDOTP.
Figure 10. Power-Up Reset Timing
Rev. D
|
Page 40 of 88 | July 2013
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Asynchronous Memory Read Cycle Timing
Table 34. Asynchronous Memory Read Cycle Timing
Parameter
Timing Requirements
tSDAT
DATA15–0 Setup Before CLKOUT
tHDAT
DATA15–0 Hold After CLKOUT
tSARDY
ARDY Setup Before CLKOUT
tHARDY
ARDY Hold After CLKOUT
Switching Characteristics
tDO
Output Delay After CLKOUT1
tHO
Output Hold After CLKOUT1
1
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDMEM
VDDMEM
1.8 V Nominal
2.5 V or 3.3 V
Nominal
Min
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDMEM
VDDMEM
1.8 V Nominal
2.5 V or 3.3 V
Nominal
Min
Max
Min
Max
Unit
2.1
1.2
4.0
0.2
2.1
0.9
4.0
0.2
ns
ns
ns
ns
2.1
0.8
4.0
0.2
6.0
0.8
6.0
0.8
2.1
0.8
4.0
0.2
6.0
0.8
6.0
0.8
Output balls include AMS3–0, ABE1–0, ADDR19–1, AOE, ARE.
SETUP
2 CYCLES
PROGRAMMED READ
ACCESS 4 CYCLES
ACCESS EXTENDED
3 CYCLES
HOLD
1 CYCLE
CLKOUT
tDO
tHO
AMSx
ABE1–0
ADDR19–1
AOE
tDO
tHO
ARE
tSARDY
tHARDY
ARDY
tSARDY
tHARDY
DATA 15–0
Figure 11. Asynchronous Memory Read Cycle Timing
Rev. D |
Page 41 of 88 | July 2013
tSDAT
tHDAT
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Asynchronous Memory Write Cycle Timing
Table 35. Asynchronous Memory Write Cycle Timing
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDMEM
1.8 V Nominal
Parameter
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDMEM
2.5 V or 3.3 V
Nominal
Min
Max
VDDMEM
1.8 V Nominal
Min
Max
VDDMEM
2.5 V or 3.3 V
Nominal
Min
Max
Unit
Timing Requirements
tSARDY
ARDY Setup Before CLKOUT
4.0
4.0
4.0
4.0
ns
tHARDY
ARDY Hold After CLKOUT
0.2
0.2
0.2
0.2
ns
Switching Characteristics
tDDAT
DATA15–0 Disable After CLKOUT
tENDAT
DATA15–0 Enable After CLKOUT
tDO
Output Delay After CLKOUT1
tHO
1
6.0
0.0
6.0
6.0
1
Output Hold After CLKOUT
6.0
0.0
0.8
0.0
6.0
6.0
0.8
0.8
Output balls include AMS3–0, ABE1–0, ADDR19–1, DATA15–0, AWE.
PROGRAMMED
WRITE
ACCESS
ACCESS
EXTEND HOLD
2 CYCLES
1 CYCLE 1 CYCLE
SETUP
2 CYCLES
CLKOUT
tDO
tHO
AMSx
ABE1–0
ADDR19–1
tHO
tDO
AWE
tSARDY
tHARDY
ARDY
tENDAT
tHARDY
tSARDY
tDDAT
DATA 15–0
Figure 12. Asynchronous Memory Write Cycle Timing
Rev. D
|
6.0
0.0
Page 42 of 88 | July 2013
6.0
0.8
ns
ns
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
NAND Flash Controller Interface Timing
Table 36 and Figure 13 on Page 44 through Figure 17 on
Page 46 describe NAND Flash Controller Interface operations.
Table 36. NAND Flash Controller Interface Timing
VDDEXT
1.8 V Nominal
Parameter
VDDEXT
2.5 V or 3.3 V Nominal
Min
Min
Unit
ns
Write Cycle
Switching Characteristics
tCWL
ND_CE Setup Time to AWE Low
1.0 × tSCLK – 4
1.0 × tSCLK – 4
tCH
ND_CE Hold Time From AWE High
3.0 × tSCLK – 4
3.0 × tSCLK – 4
ns
tCLEWL
ND_CLE Setup Time to AWE Low
0.0
0.0
ns
tCLH
ND_CLE Hold Time From AWE high
2.5 × tSCLK – 4
2.5 × tSCLK – 4
ns
tALEWL
ND_ALE Setup Time to AWE Low
0.0
0.0
ns
tALH
ND_ALE Hold Time From AWE High
2.5 × tSCLK – 4
2.5 × tSCLK – 4
ns
tWP1
AWE Low to AWE high
(WR_DLY +1.0) × tSCLK – 4
(WR_DLY +1.0) × tSCLK – 4
ns
tWHWL
AWE High to AWE Low
4.0 × tSCLK – 4
4.0 × tSCLK – 4
ns
tWC1
AWE Low to AWE Low
(WR_DLY +5.0) × tSCLK – 4
(WR_DLY +5.0) × tSCLK – 4
ns
tDWS1
Data Setup Time for a Write Access
(WR_DLY +1.5) × tSCLK – 4
(WR_DLY +1.5) × tSCLK – 4
ns
tDWH
Data Hold Time for a Write Access
2.5 × tSCLK – 4
2.5 × tSCLK – 4
ns
Read Cycle
Switching Characteristics
tCRL
ND_CE Setup Time to ARE Low
1.0 × tSCLK – 4
1.0 × tSCLK – 4
ns
tCRH
ND_CE Hold Time From ARE High
3.0 × tSCLK – 4
3.0 × tSCLK – 4
ns
1
ARE Low to ARE High
(RD_DLY +1.0) × tSCLK – 4
(RD_DLY +1.0) × tSCLK – 4
ns
tRHRL
ARE High to ARE Low
4.0 × tSCLK – 4
4.0 × tSCLK – 4
ns
tRC1
ARE Low to ARE Low
(RD_DLY +5.0) × tSCLK – 4
(RD_DLY +5.0) × tSCLK – 4
ns
tRP
Timing Requirements (ADSP-BF522/ADSP-BF524/ADSP-BF526)
tDRS
Data Setup Time for a Read Transaction
14.0
10.0
ns
tDRH
Data Hold Time for a Read Transaction
0.0
0.0
ns
Timing Requirements (ADSP-BF523/ADSP-BF525/ADSP-BF527)
tDRS
Data Setup Time for a Read Transaction
11.0
8.0
ns
tDRH
Data Hold Time for a Read Transaction
0.0
0.0
ns
5.0 × tSCLK – 4
5.0 × tSCLK – 4
ns
Write Followed by Read
Switching Characteristic
tWHRL
1
AWE High to ARE Low
WR_DLY and RD_DLY are defined in the NFC_CTL register.
Rev. D |
Page 43 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
tCWL
tCH
ND_CE
ND_CLE
tCLEWL
tCLH
tALEWL
tALH
ND_ALE
tWP
AWE
tDWH
tDWS
ND_DATA
In Figure 13, ND_DATA is ND_D0–D7.
Figure 13. NAND Flash Controller Interface Timing — Command Write Cycle
tCWL
ND_CE
tCLEWL
ND_CLE
ND_ALE
tALH
tALEWL
tALH
tALEWL
tWP
tWHWL
tWP
AWE
tWC
tDWS
tDWH
tDWS
ND_DATA
In Figure 14, ND_DATA is ND_D0–D7.
Figure 14. NAND Flash Controller Interface Timing — Address Write Cycle
Rev. D
|
Page 44 of 88 | July 2013
tDWH
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
tCWL
ND_CE
tCLEWL
ND_CLE
tALEWL
ND_ALE
tWP
tWC
AWE
tWP
tDWS
tWHWL
tDWH
tDWS
tDWH
ND_DATA
In Figure 15, ND_DATA is ND_D0–D7.
Figure 15. NAND Flash Controller Interface Timing — Data Write Operation
tCRL
tCRH
ND_CE
ND_CLE
ND_ALE
tRP
tRC
ARE
tRHRL
tRP
tDRS
tDRH
tDRS
ND_DATA
In Figure 16, ND_DATA is ND_D0–D7.
Figure 16. NAND Flash Controller Interface Timing — Data Read Operation
Rev. D |
Page 45 of 88 | July 2013
tDRH
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
tCLWL
ND_CE
ND_CLE
tCLEWL
tCLH
tWP
AWE
tWHRL
tRP
ARE
tDWS
tDWH
tDRS
tDRH
ND_DATA
In Figure 17, ND_DATA is ND_D0–D7.
Figure 17. NAND Flash Controller Interface Timing — Write Followed by Read Operation
Rev. D
|
Page 46 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
SDRAM Interface Timing
Table 37. SDRAM Interface Timing for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
VDDMEM
1.8V Nominal
Parameter
Min
Max
VDDMEM
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tSSDAT
Data Setup Before CLKOUT
1.5
1.5
ns
tHSDAT
Data Hold After CLKOUT
1.3
0.8
ns
Switching Characteristics
tSCLK
CLKOUT Period1
12.5
10
ns
tSCLKH
CLKOUT Width High
5.0
4.0
ns
tSCLKL
CLKOUT Width Low
5.0
4.0
ns
tDCAD
Command, Address, Data Delay After CLKOUT
tHCAD
Command, Address, Data Hold After CLKOUT2
tDSDAT
Data Disable After CLKOUT
tENSDAT
Data Enable After CLKOUT
1
2
2
5.0
1.0
4.0
1.0
ns
5.5
0.0
ns
5.0
0.0
ns
ns
The tSCLK value is the inverse of the fSCLK specification discussed in Table 14 and Table 17. Package type and reduced supply voltages affect the best-case values listed here.
Command balls include: SRAS, SCAS, SWE, SDQM, SMS, SA10, SCKE.
Table 38. SDRAM Interface Timing for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
VDDMEM
1.8V Nominal
Parameter
Min
Max
VDDMEM
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tSSDAT
Data Setup Before CLKOUT
1.5
1.5
ns
tHSDAT
Data Hold After CLKOUT
1.0
0.8
ns
Switching Characteristics
tSCLK
CLKOUT Period1
10
7.5
ns
tSCLKH
CLKOUT Width High
2.5
2.5
ns
tSCLKL
CLKOUT Width Low
2.5
2.5
ns
tDCAD
Command, Address, Data Delay After CLKOUT
tHCAD
Command, Address, Data Hold After CLKOUT2
tDSDAT
Data Disable After CLKOUT
tENSDAT
Data Enable After CLKOUT
1
2
2
4.0
1.0
4.0
1.0
5.0
0.0
ns
4.0
0.0
ns
ns
ns
The tSCLK value is the inverse of the fSCLK specification discussed in Table 14 and Table 17. Package type and reduced supply voltages affect the best-case values listed here.
Command balls include: SRAS, SCAS, SWE, SDQM, SMS, SA10, SCKE.
Rev. D |
Page 47 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
tSCLK
CLKOUT
tSSDAT
tHSDAT
tSCLKL
tSCLKH
DATA (IN)
tENSDAT
tDCAD
tHCAD
DATA (OUT)
tDCAD
tHCAD
COMMAND,
ADDRESS
(OUT)
NOTE: COMMAND = SRAS, SCAS, SWE, SDQM, SMS, SA10, SCKE.
Figure 18. SDRAM Interface Timing
Rev. D
|
Page 48 of 88 | July 2013
tDSDAT
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
External DMA Request Timing
Table 39, Table 40, and Figure 19 describe the External DMA
Request operations.
Table 39. External DMA Request Timing for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors1
VDDEXT/VDDMEM
1.8 V Nominal
Parameter
Min
Max
VDDEXT/VDDMEM
2.5 V or 3.3 V Nominal
Min
Max
Unit
Timing Requirements
1
tDS
DMARx Asserted to CLKOUT High Setup
9.0
6.0
ns
tDH
CLKOUT High to DMARx Deasserted Hold Time
0.0
0.0
ns
tDMARACT
DMARx Active Pulse Width
1.0 × tSCLK
1.0 × tSCLK
ns
tDMARINACT
DMARx Inactive Pulse Width
1.75 × tSCLK
1.75 × tSCLK
ns
Because the external DMA control pins are part of the VDDEXT power domain and the CLKOUT signal is part of the VDDMEM power domain, systems in which VDDEXT and
VDDMEM are NOT equal may require level shifting logic for correct operation.
Table 40. External DMA Request Timing for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors1
VDDEXT/VDDMEM
1.8 V Nominal
Parameter
Min
Max
VDDEXT/VDDMEM
2.5 V or 3.3 V Nominal
Min
Max
Unit
Timing Requirements
1
tDS
DMARx Asserted to CLKOUT High Setup
8.0
6.0
ns
tDH
CLKOUT High to DMARx Deasserted Hold Time
0.0
0.0
ns
tDMARACT
DMARx Active Pulse Width
1.0 × tSCLK
1.0 × tSCLK
ns
tDMARINACT
DMARx Inactive Pulse Width
1.75 × tSCLK
1.75 × tSCLK
ns
Because the external DMA control pins are part of the VDDEXT power domain and the CLKOUT signal is part of the VDDMEM power domain, systems in which VDDEXT and
VDDMEM are NOT equal may require level shifting logic for correct operation.
CLKOUT
tDS
tDH
DMAR0/1
(ACTIVE LOW)
tDMARACT
tDMARINACT
DMAR0/1
(ACTIVE HIGH)
Figure 19. External DMA Request Timing
Rev. D |
Page 49 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Parallel Peripheral Interface Timing
Table 41 and Figure 20 on Page 51, Figure 24 on Page 55, and
Figure 27 on Page 57 describe parallel peripheral interface
operations.
Table 41. Parallel Peripheral Interface Timing for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3 V Nominal
Min
Max
Unit
Timing Requirements
tPCLKW
PPI_CLK Width1
6.4
6.4
ns
tPCLK
PPI_CLK Period1
25.0
20.0
ns
Timing Requirements - GP Input and Frame Capture Modes
tSFSPE
External Frame Sync Setup Before PPI_CLK
(Nonsampling Edge for Rx, Sampling Edge for Tx)
6.7
6.7
ns
tHFSPE
External Frame Sync Hold After PPI_CLK
1.2
1.2
ns
tSDRPE
Receive Data Setup Before PPI_CLK
4.1
3.5
ns
tHDRPE
Receive Data Hold After PPI_CLK
2.0
1.6
ns
Switching Characteristics - GP Output and Frame Capture Modes
tDFSPE
Internal Frame Sync Delay After PPI_CLK
tHOFSPE
Internal Frame Sync Hold After PPI_CLK
tDDTPE
Transmit Data Delay After PPI_CLK
tHDTPE
Transmit Data Hold After PPI_CLK
1
8.0
1.7
8.0
ns
8.0
ns
1.7
8.2
2.3
ns
1.9
ns
PPI_CLK frequency cannot exceed fSCLK/2.
Table 42. Parallel Peripheral Interface Timing for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tPCLKW
PPI_CLK Width1
6.0
6.0
ns
tPCLK
PPI_CLK Period1
20.0
15.0
ns
6.7
6.7
ns
Timing Requirements - GP Input and Frame Capture Modes
tSFSPE
External Frame Sync Setup Before PPI_CLK
(Nonsampling Edge for Rx, Sampling Edge for Tx)
tHFSPE
External Frame Sync Hold After PPI_CLK
1.0
1.0
ns
tSDRPE
Receive Data Setup Before PPI_CLK
3.5
3.5
ns
tHDRPE
Receive Data Hold After PPI_CLK
2.0
1.6
ns
Switching Characteristics - GP Output and Frame Capture Modes
tDFSPE
Internal Frame Sync Delay After PPI_CLK
tHOFSPE
Internal Frame Sync Hold After PPI_CLK
tDDTPE
Transmit Data Delay After PPI_CLK
tHDTPE
Transmit Data Hold After PPI_CLK
1
8.0
1.7
2.3
Rev. D
|
Page 50 of 88 | July 2013
ns
8.0
ns
1.7
8.0
PPI_CLK frequency cannot exceed fSCLK/2.
8.0
1.9
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
DATA SAMPLED /
FRAME SYNC SAMPLED
DATA SAMPLED /
FRAME SYNC SAMPLED
PPI_CLK
tSFSPE
tPCLKW
tHFSPE
tPCLK
PPI_FS1/2
tSDRPE
tHDRPE
PPI_DATA
Figure 20. PPI GP Rx Mode with External Frame Sync Timing
DATA DRIVEN /
FRAME SYNC SAMPLED
PPI_CLK
tSFSPE
tHFSPE
tPCLKW
PPI_FS1/2
tDDTPE
tHDTPE
PPI_DATA
Figure 21. PPI GP Tx Mode with External Frame Sync Timing
FRAME SYNC
DRIVEN
DATA
SAMPLED
PPI_CLK
tHOFSPE
tDFSPE
tPCLKW
tPCLK
PPI_FS1/2
tSDRPE
tHDRPE
PPI_DATA
Figure 22. PPI GP Rx Mode with Internal Frame Sync Timing
Rev. D |
Page 51 of 88 | July 2013
tPCLK
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
FRAME SYNC
DRIVEN
DATA
DRIVEN
tPCLK
PPI_CLK
tHOFSPE
tDFSPE
tPCLKW
PPI_FS1/2
tDDTPE
PPI_DATA
Figure 23. PPI GP Tx Mode with Internal Frame Sync Timing
Rev. D
|
Page 52 of 88 | July 2013
tHDTPE
DATA
DRIVEN
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Serial Ports
Table 43 through Table 47 on Page 57 and Figure 24 on Page 55
through Figure 27 on Page 57 describe serial port operations.
Table 43. Serial Ports—External Clock
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Parameter
Min
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Max
Min
Max
Unit
Timing Requirements
tSFSE
TFSx/RFSx Setup Before TSCLKx RSCLKx1 3.0
1
3.0
3.0
3.0
ns
tHFSE
TFSx/RFSx Hold After TSCLKx/RSCLKx
3.0
3.0
3.0
3.0
ns
tSDRE
Receive Data Setup Before RSCLKx1
3.0
3.0
3.0
3.0
ns
3.5
3.0
3.5
3.0
ns
7.0
4.5
7.0
4.5
ns
tHDRE
Receive Data Hold After RSCLKx
1
tSCLKEW TSCLKx/RSCLKx Width
tSCLKE
2.0 × tSCLK
2.0 × tSCLK
2.0 × tSCLK
2.0 × tSCLK
ns
tSUDTE Start-Up Delay From SPORT Enable To
First External TFSx2
TSCLKx/RSCLKx Period
4.0 × tSCLKE
4.0 × tSCLKE
4.0 × tSCLKE
4.0 × tSCLKE
ns
tSUDRE Start-Up Delay From SPORT Enable To
First External RFSx2
4.0 × tSCLKE
4.0 × tSCLKE
4.0 × tSCLKE
4.0 × tSCLKE
ns
Switching Characteristics
tDFSE
TFSx/RFSx Delay After TSCLKx/RSCLKx
(Internally Generated TFSx/RFSx)3
tHOFSE TFSx/RFSx Hold After TSCLKx/RSCLKx
(Internally Generated TFSx/RFSx)3
tDDTE
tHDTE
10.0
0.0
Transmit Data Delay After TSCLKx3
Transmit Data Hold After TSCLKx
3
10.0
0.0
10.0
0.0
0.0
10.0
0.0
1
Referenced to sample edge.
Verified in design but untested.
3
Referenced to drive edge.
2
Rev. D |
10.0
Page 53 of 88 | July 2013
10.0
0.0
10.0
0.0
ns
10.0
0.0
ns
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 44. Serial Ports—Internal Clock for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
VDDEXT
1.8V Nominal
Min
Parameter
VDDEXT
2.5 V or 3.3V Nominal
Max
Min
Max
Unit
Timing Requirements
tSFSI
TFSx/RFSx Setup Before TSCLKx/RSCLKx1
11.0
9.6
ns
tHFSI
TFSx/RFSx Hold After TSCLKx/RSCLKx1
–1.5
–1.5
ns
11.0
9.6
ns
–1.5
–1.5
ns
tSDRI
tHDRI
Receive Data Setup Before RSCLKx
Receive Data Hold After RSCLKx
1
1
Switching Characteristics
tSCLKIW
TSCLKx/RSCLKx Width
tDFSI
TFSx/RFSx Delay After TSCLKx/RSCLKx (Internally Generated TFSx/RFSx)2
tHOFSI
TFSx/RFSx Hold After TSCLKx/RSCLKx (Internally Generated TFSx/RFSx)2 –2.0
tDDTI
Transmit Data Delay After TSCLKx2
tHDTI
Transmit Data Hold After TSCLKx2
1
2
10.0
8.0
3.0
ns
3.0
ns
3.0
ns
–1.0
3.0
–1.8
ns
–1.5
ns
Referenced to sample edge.
Referenced to drive edge.
Table 45. Serial Ports—Internal Clock for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tSFSI
TFSx/RFSx Setup Before TSCLKx/RSCLKx1
tHFSI
TFSx/RFSx Hold After TSCLKx/RSCLKx
tSDRI
Receive Data Setup Before RSCLKx1
tHDRI
Receive Data Hold After RSCLKx
1
1
11.0
9.6
ns
–1.5
–1.5
ns
11.0
9.6
ns
–1.5
–1.5
ns
4.5
4.5
ns
Switching Characteristics
tSCLKIW
TSCLKx/RSCLKx Width
tDFSI
TFSx/RFSx Delay After TSCLKx/RSCLKx
(Internally Generated TFSx/RFSx)2
tHOFSI
TFSx/RFSx Hold After TSCLKx/RSCLKx
(Internally Generated TFSx/RFSx)2
tDDTI
Transmit Data Delay After TSCLKx2
tHDTI
1
2
Transmit Data Hold After TSCLKx
3.0
–1.0
–1.0
3.0
2
–1.8
Referenced to sample edge.
Referenced to drive edge.
Rev. D
3.0
|
Page 54 of 88 | July 2013
ns
3.0
–1.5
ns
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
DATA RECEIVE—INTERNAL CLOCK
DATA RECEIVE—EXTERNAL CLOCK
DRIVE EDGE
DRIVE EDGE
SAMPLE EDGE
SAMPLE EDGE
tSCLKE
tSCLKEW
tSCLKIW
RSCLKx
RSCLKx
tDFSE
tDFSI
tHOFSI
tHOFSE
RFSx
(OUTPUT)
RFSx
(OUTPUT)
tSFSI
tHFSI
RFSx
(INPUT)
tSFSE
tHFSE
tSDRE
tHDRE
RFSx
(INPUT)
tSDRI
tHDRI
DRx
DRx
DATA TRANSMIT—INTERNAL CLOCK
DRIVE EDGE
DATA TRANSMIT—EXTERNAL CLOCK
SAMPLE EDGE
DRIVE EDGE
tSCLKIW
SAMPLE EDGE
t SCLKEW
TSCLKx
tSCLKE
TSCLKx
tD FSI
tDFSE
tHOFSI
tHOFSE
TFSx
(OUTPUT)
TFSx
(OUTPUT)
tSFSI
tHFSI
tSFSE
TFSx
(INPUT)
TFSx
(INPUT)
tDDTI
tDDTE
tHDTI
tHDTE
DTx
DTx
Figure 24. Serial Ports
TSCLKx
(INPUT)
tSUDTE
TFSx
(INPUT)
RSCLKx
(INPUT)
tSUDRE
RFSx
(INPUT)
FIRST
TSCLKx/RSCLKx
EDGE AFTER
SPORT ENABLED
Figure 25. Serial Port Start Up with External Clock and Frame Sync
Rev. D |
Page 55 of 88 | July 2013
tHFSE
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 46. Serial Ports—Enable and Three-State
ADSP-BF522/ADSP-BF524/ADSP-BF526
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
ADSP-BF523/ADSP-BF525/ADSP-BF527
VDDEXT
1.8V Nominal
Min
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Switching Characteristics
tDTENE
Data Enable Delay from
External TSCLKx1
tDDTTE
Data Disable Delay from
External TSCLKx1
tDTENI
Data Enable Delay from
Internal TSCLKx1
tDDTTI
Data Disable Delay from
Internal TSCLKx1
1
0.0
0.0
tSCLK +1
–2.0
0.0
tSCLK +1
–2.0
tSCLK +1
tSCLK +1
–2.0
tSCLK +1
DRIVE EDGE
TSCLKx
tDTENE/I
tDDTTE/I
DTx
Figure 26. Serial Ports — Enable and Three-State
Rev. D
|
Page 56 of 88 | July 2013
ns
tSCLK +1
–2.0
tSCLK +1
Referenced to drive edge.
DRIVE EDGE
0.0
ns
ns
tSCLK +1
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 47. Serial Ports — External Late Frame Sync
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Parameter
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Max
Min
Max
Unit
10.0
ns
Switching Characteristics
tDDTLFSE
Data Delay from Late External TFSx
or External RFSx in multi-channel mode
with MFD = 01, 2
tDTENLFSE
Data Enable from External RFSx in multi- 0.0
channel mode with MFD = 01, 2
1
2
12.0
10.0
0.0
12.0
0.0
When in multi-channel mode, TFSx enable and TFSx valid follow tDTENLFSE and tDDTLFSE.
If external RFSx/TFSx setup to RSCLKx/TSCLKx > tSCLKE/2 then tDDTTE/I and tDTENE/I apply, otherwise tDDTLFSE and tDTENLFSE apply.
EXTERNAL RFSx IN MULTI-CHANNEL MODE
SAMPLE
DRIVE
EDGE
EDGE
DRIVE
EDGE
RSCLKx
RFSx
tDDTLFSE
tDTENLFSE
1ST BIT
DTx
LATE EXTERNAL TFSx
DRIVE
EDGE
SAMPLE
EDGE
DRIVE
EDGE
TSCLKx
TFSx
tDDTLFSE
1ST BIT
DTx
Figure 27. Serial Ports — External Late Frame Sync
Rev. D |
Page 57 of 88 | July 2013
0.0
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Serial Peripheral Interface (SPI) Port—Master Timing
Table 48 and Figure 28 describe SPI port master operations.
Table 48. Serial Peripheral Interface (SPI) Port—Master Timing
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Parameter
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
Min
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Max
Min
Max
Min
Max
Unit
Timing Requirements
tSSPIDM
Data Input Valid to SCK Edge (Data 11.6
Input Setup)
9.6
11.6
9.6
ns
tHSPIDM
SCK Sampling Edge to Data Input
Invalid
–1.5
–1.5
–1.5
–1.5
ns
Switching Characteristics
tSDSCIM
SPISELx low to First SCK Edge
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPICHM
Serial Clock High Period
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPICLM
Serial Clock Low Period
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPICLK
Serial Clock Period
4 × tSCLK –1.5
4 × tSCLK –1.5
4 × tSCLK –1.5
4 × tSCLK –1.5
ns
tHDSM
Last SCK Edge to SPISELx High
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPITDM
Sequential Transfer Delay
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tDDSPIDM
SCK Edge to Data Out Valid (Data
Out Delay)
tHDSPIDM
SCK Edge to Data Out Invalid (Data –1.0
Out Hold)
6
6
6
–1.0
6
–1.0
–1.0
SPIxSELy
(OUTPUT)
tSDSCIM
tSPICLM
tSPICHM
tSPICLK
tHDSM
SPIxSCK
(OUTPUT)
tDDSPIDM
tHDSPIDM
SPIxMOSI
(OUTPUT)
tSSPIDM
CPHA = 1
tHSPIDM
SPIxMISO
(INPUT)
tHDSPIDM
tDDSPIDM
SPIxMOSI
(OUTPUT)
CPHA = 0
tSSPIDM
tHSPIDM
SPIxMISO
(INPUT)
Figure 28. Serial Peripheral Interface (SPI) Port—Master Timing
Rev. D
|
Page 58 of 88 | July 2013
tSPITDM
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Serial Peripheral Interface (SPI) Port—Slave Timing
Table 49 and Figure 29 describe SPI port slave operations.
Table 49. Serial Peripheral Interface (SPI) Port—Slave Timing
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Parameter
ADSP-BF523/ADSP-BF525/
ADSP-BF527
Max Min
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Max Min
Max Min
Max Unit
Timing Requirements
tSPICHS
Serial Clock High Period
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPICLS
Serial Clock Low Period
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPICLK
Serial Clock Period
4×
tSCLK –1.5
4 × tSCLK –1.5
4×
tSCLK –1.5
4 × tSCLK –1.5
ns
tHDS
Last SCK Edge to SPISS Not Asserted
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSPITDS
Sequential Transfer Delay
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSDSCI
SPISS Assertion to First SCK Edge
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
2 × tSCLK –1.5
ns
tSSPID
Data Input Valid to SCK Edge (Data Input
Setup)
1.6
1.6
1.6
1.6
ns
tHSPID
SCK Sampling Edge to Data Input Invalid
2.0
1.6
1.6
1.6
ns
Switching Characteristics
tDSOE
SPISS Assertion to Data Out Active
0
12.0 0
10.3
0
12.0 0
10.3
ns
tDSDHI
SPISS Deassertion to Data High Impedance 0
11.0 0
8.5
0
8.5
8
ns
tDDSPID
SCK Edge to Data Out Valid (Data Out Delay)
10
10
10
ns
tHDSPID
SCK Edge to Data Out Invalid (Data Out Hold) 0
0
0
10
0
0
ns
SPIxSS
(INPUT)
tSDSCI
tSPICLS
tSPICHS
tHDS
tSPICLK
SPIxSCK
(INPUT)
tDSOE
tDDSPID
tDDSPID
tHDSPID
tDSDHI
SPIxMISO
(OUTPUT)
CPHA = 1
tSSPID
tHSPID
SPIxMOSI
(INPUT)
tDSOE
tHDSPID
tDDSPID
tDSDHI
SPIxMISO
(OUTPUT)
CPHA = 0
tSSPID
SPIxMOSI
(INPUT)
Figure 29. Serial Peripheral Interface (SPI) Port—Slave Timing
Rev. D |
Page 59 of 88 | July 2013
tHSPID
tSPITDS
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Universal Serial Bus (USB) On-The-Go—Receive and Transmit Timing
Table 50 describes the USB On-The-Go receive and transmit
operations.
Table 50. USB On-The-Go—Receive and Transmit Timing
ADSP-BF522/ADSP-BF524/ADSP-BF526
VDDEXT
1.8V Nominal
Parameter
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
1.8V Nominal
VDDEXT
2.5 V or 3.3V Nominal
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Timing Requirements
fUSBS
USB_XI Frequency
12
33.3
12
33.3
9
33.3
9
33.3
MHz
FSUSB
USB_XI Clock Frequency
Stability
–50
+50
–50
+50
–50
+50
–50
+50
ppm
Rev. D
|
Page 60 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Universal Asynchronous Receiver-Transmitter
(UART) Ports—Receive and Transmit Timing
For information on the UART port receive and transmit operations, see the ADSP-BF52x Hardware Reference Manual.
General-Purpose Port Timing
Table 51 and Figure 30 describe general-purpose
port operations.
Table 51. General-Purpose Port Timing for ADSP-BF522/ADSP-BF524/ADSP-BF526 Processors
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirement
tWFI
General-Purpose Port Ball Input Pulse Width
tSCLK + 1
tSCLK + 1
ns
Switching Characteristic
tGPOD
General-Purpose Port Ball Output Delay from CLKOUT 0
Low
11.0
0
8.2
ns
Table 52. General-Purpose Port Timing for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors
VDDEXT
1.8V Nominal
Parameter
Min
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirement
tWFI
General-Purpose Port Ball Input Pulse Width
tSCLK + 1
tSCLK + 1
ns
Switching Characteristic
tGPOD
General-Purpose Port Ball Output Delay from CLKOUT Low 0
CLKOUT
tGPOD
GPIO OUTPUT
tWFI
GPIO INPUT
Figure 30. General-Purpose Port Timing
Rev. D |
Page 61 of 88 | July 2013
8.2
0
6.5
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Timer Cycle Timing
Table 53 and Figure 31 describe timer expired operations. The
input signal is asynchronous in “width capture mode” and
“external clock mode” and has an absolute maximum input frequency of (fSCLK/2) MHz.
Table 53. Timer Cycle Timing
ADSP-BF522/ADSP-BF524/ADSP-BF526
VDDEXT
1.8V Nominal
Min
Parameter
ADSP-BF523/ADSP-BF525/ADSP-BF527
VDDEXT
1.8V Nominal
VDDEXT
2.5 V or 3.3V Nominal
Max
Min
Max
Min
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tWL
Timer Pulse Width Input tSCLK
Low (Measured In SCLK
Cycles)1
tSCLK
tSCLK
tSCLK
ns
tWH
Timer Pulse Width Input tSCLK
High (Measured In SCLK
Cycles)1
tSCLK
tSCLK
tSCLK
ns
tTIS
Timer Input Setup Time
Before CLKOUT Low2
10
7
8.1
6.2
ns
tTIH
Timer Input Hold Time
After CLKOUT Low2
–2
–2
–2
–2
ns
Switching Characteristics
tHTO
Timer Pulse Width Output tSCLK –1.5
(Measured In SCLK Cycles)
(232– 1)tSCLK tSCLK – 1
(232– 1)tSCLK tSCLK – 1
(232– 1)tSCLK tSCLK – 1
(232 – 1)tSCLK ns
tTOD
Timer Output Update
Delay After CLKOUT High
6
6
6
6
1
2
ns
The minimum pulse widths apply for TMRx signals in width capture and external clock modes. They also apply to the PF15 or PPI_CLK signals in PWM output mode.
Either a valid setup and hold time or a valid pulse width is sufficient. There is no need to resynchronize programmable flag inputs.
CLKOUT
tTOD
TMRx OUTPUT
tTIS
tTIH
TMRx INPUT
tWH,tWL
Figure 31. Timer Cycle Timing
Rev. D
|
Page 62 of 88 | July 2013
tHTO
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Timer Clock Timing
Table 54 and Figure 32 describe timer clock timing.
Table 54. Timer Clock Timing
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
12.0
ns
Switching Characteristic
tTODP
Timer Output Update Delay After PPI_CLK High
12.0
PPI_CLK
tTODP
TMRx OUTPUT
Figure 32. Timer Clock Timing
Up/Down Counter/Rotary Encoder Timing
Table 55. Up/Down Counter/Rotary Encoder Timing
VDDEXT
1.8V Nominal
Parameter
Min
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tWCOUNT
Up/Down Counter/Rotary Encoder Input Pulse Width tSCLK + 1
tCIS
Counter Input Setup Time Before CLKOUT High
tCIH
Counter Input Hold Time After CLKOUT High1
1
1
tSCLK + 1
ns
9.0
7.0
ns
0
0
ns
Either a valid setup and hold time or a valid pulse width is sufficient. There is no need to resynchronize counter inputs.
CLKOUT
tCIS
tCIH
CUD/CDG/CZM
tWCOUNT
Figure 33. Up/Down Counter/Rotary Encoder Timing
Rev. D |
Page 63 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
HOSTDP A/C Timing- Host Read Cycle
Table 56 describes the HOSTDP A/C Host Read Cycle timing
requirements.
Table 56. Host Read Cycle Timing Requirements
Parameter
Timing Requirements
tSADRDL
HOST_ADDR and HOST_CE Setup
before HOST_RD falling edge
tHADRDH HOST_ADDR and HOST_CE Hold
after HOST_RD rising edge
tRDWL
HOST_RD pulse width low
(ACK mode)
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
VDDEXT
2.5 V or 3.3V
Nominal
1.8V Nominal
Min
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
VDDEXT
2.5 V or 3.3V
Nominal
1.8V Nominal
Min
Max
Min
Max
Unit
4
4
4
4
ns
2.5
2.5
2.5
2.5
ns
tDRDYRDL +
tRDYPRD +
tDRDHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
tDRDYRDL +
tRDYPRD +
tDRDHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
tDRDYRDL +
tRDYPRD +
tDRDHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
ns
2.0
0
0
ns
3.5
4.5
3.5
ns
tDRDYRDL +
tRDYPRD +
tDRDHRDY
tRDWL
HOST_RD pulse width low
1.5 × tSCLK
(INT mode)
+ 8.7
tRDWH
HOST_RD pulse width high or time 2 × tSCLK
between HOST_RD rising edge and
HOST_WR falling edge
tDRDHRDY HOST_RD rising edge delay after 2.0
HOST_ACK rising edge (ACK mode)
Switching Characteristics
tSDATRDY Data valid prior HOST_ACK rising 4.5
edge (ACK mode)
tDRDYRDL Host_ACK falling edge after
HOST_CE (ACK mode)
tRDYPRD
HOST_ACK low pulse-width for
Read access (ACK mode)
tDDARWH Data disable after HOST_RD
tACC
Data valid after HOST_RD falling
edge (INT mode)
tHDARWH Data hold after HOST_RD rising
1.0
edge
1
ns
ns
12.5
11.25
11.25
11.25
ns
NM1
NM1
NM1
NM1
ns
11.0
1.5 × tSCLK
9.0
1.5 × tSCLK
9.0
1.5 × tSCLK
9.0
ns
1.5 × tSCLK ns
1.0
1.0
1.0
ns
NM (Not Measured) — This parameter is based on tSCLK. It is not measured because the number of SCLK cycles for which HOST_ACK is low depends on the Host DMA FIFO
status and is system design dependent.
Rev. D
|
Page 64 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
HOST_ADDR
HOST_CE
tSADRDL
tHADRDH
tRDWL
HOST_RD
tSDATRDY
tACC
tRDWH
tDDARWH
tHDARWH
HOST_DATA
tDRDYRDL
tDRDHRDY
tRDYPRD
HOST_ACK
In Figure 34, HOST_DATA is HOST_D0–D15.
Figure 34. HOSTDP A/C- Host Read Cycle
Rev. D |
Page 65 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
HOSTDP A/C Timing- Host Write Cycle
Table 57 describes the HOSTDP A/C Host Write Cycle timing
requirements.
Table 57. Host Write Cycle Timing Requirements
Parameter
Timing Requirements
tSADWRL HOST_ADDR/HOST_CE Setup
before HOST_WR falling edge
tHADWRH HOST_ADDR/HOST_CE Hold
after HOST_WR rising edge
HOST_WR pulse width low
tWRWL
(ACK mode)
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
VDDEXT
Nominal
1.8V Nominal
Min
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
VDDEXT
2.5 V or 3.3V
Nominal
1.8V Nominal
Min
Max
Min
Max
Unit
4
4
4
4
ns
2.5
2.5
2.5
2.5
ns
tDRDYWRL +
tRDYPRD +
tDWRHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
tDRDYWRL +
tRDYPRD +
tDWRHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
tDRDYWRL +
tRDYPRD +
tDWRHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
tDRDYWRL +
tRDYPRD +
tDWRHRDY
1.5 × tSCLK
+ 8.7
2 × tSCLK
ns
2.0
0
0
ns
2.5
2.5
2.5
2.5
2.5
2.5
ns
ns
HOST_WR pulse width low
(INT mode)
HOST_WR pulse width high
tWRWH
or time between HOST_WR
rising edge and HOST_RD
falling edge
tDWRHRDY HOST_WR rising edge delay
2.0
after HOST_ACK rising edge
(ACK mode)
tHDATWH Data Hold after HOST_WR rising edge 2.5
3.5
tSDATWH Data Setup before HOST_WR
rising edge
Switching Characteristics
tDRDYWRL HOST_ACK falling edge after HOST_CE
asserted (ACK mode)
tRDYPWR HOST_ACK low pulse-width for Write
access (ACK mode)
1
ns
ns
12.5
11.5
11.5
11.5
ns
NM1
NM1
NM1
NM1
ns
NM (Not Measured) — This parameter is based on tSCLK. It is not measured because the number of SCLK cycles for which HOST_ACK is low depends on the Host DMA FIFO
status and is system design dependent.
Rev. D
|
Page 66 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
HOST_ADDR
HOST_CE
tSADWRL
tHADWRH
tWRWH
tWRWL
HOST_WR
tSDATWH
tHDATWH
HOST_DATA
tDRDYWRL
tRDYPWR
tDWRHRDY
HOST_ACK
In Figure 35, HOST_DATA is HOST_D0–D15.
Figure 35. HOSTDP A/C- Host Write Cycle
Rev. D |
Page 67 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
10/100 Ethernet MAC Controller Timing
Table 58 through Table 63 and Figure 36 through Figure 41
describe the 10/100 Ethernet MAC Controller operations.
Table 58. 10/100 Ethernet MAC Controller Timing: MII Receive Signal
VDDEXT
1.8V Nominal
Parameter1
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Min
Max
Unit
25 + 1%
None
25 + 1%
MHz
Timing Requirements
tERXCLKF
ERxCLK Frequency (fSCLK = SCLK Frequency)
None
tERXCLKW
ERxCLK Width (tERxCLK = ERxCLK Period)
tERxCLK × 40% tERxCLK × 60% tERxCLK × 35% tERxCLK × 65% ns
tERXCLKIS
Rx Input Valid to ERxCLK Rising Edge (Data In Setup)
7.5
7.5
ns
tERXCLKIH
ERxCLK Rising Edge to Rx Input Invalid (Data In Hold) 7.5
7.5
ns
1
MII inputs synchronous to ERxCLK are ERxD3–0, ERxDV, and ERxER.
tERXCLK
tERXCLKW
ERx_CLK
ERxD3–0
ERxDV
ERxER
tERXCLKIS
tERXCLKIH
Figure 36. 10/100 Ethernet MAC Controller Timing: MII Receive Signal
Table 59. 10/100 Ethernet MAC Controller Timing: MII Transmit Signal
VDDEXT
1.8V Nominal
Parameter1
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Min
Max
Unit
25 + 1%
None
25 + 1%
MHz
Switching Characteristics
tETXCLKF
ETxCLK Frequency (fSCLK = SCLK Frequency)
None
tETXCLKW
ETxCLK Width (tETxCLK = ETxCLK Period)
tETxCLK × 40% tETxCLK × 60% tETxCLK × 35% tETxCLK × 65% ns
tETXCLKOV
ETxCLK Rising Edge to Tx Output Valid (Data Out Valid)
tETXCLKOH
ETxCLK Rising Edge to Tx Output Invalid (Data Out
Hold)
1
20
0
MII outputs synchronous to ETxCLK are ETxD3–0.
tETXCLK
MIITxCLK
tETXCLKW
tETXCLKOH
ETxD3–0
ETxEN
tETXCLKOV
Figure 37. 10/100 Ethernet MAC Controller Timing: MII Transmit Signal
Rev. D
|
Page 68 of 88 | July 2013
20
0
ns
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 60. 10/100 Ethernet MAC Controller Timing: RMII Receive Signal
VDDEXT
1.8V Nominal
Parameter1
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Min
Max
Unit
50 + 1%
None
50 + 1%
MHz
Timing Requirements
tEREFCLKF
REF_CLK Frequency (fSCLK = SCLK Frequency)
None
tEREFCLKW
EREF_CLK Width (tEREFCLK = EREFCLK Period)
tEREFCLK × 40% tEREFCLK × 60% tEREFCLK × 35% tEREFCLK × 65% ns
tEREFCLKIS
Rx Input Valid to RMII REF_CLK Rising Edge (Data In
Setup)
4
4
ns
tEREFCLKIH
RMII REF_CLK Rising Edge to Rx Input Invalid (Data In 2
Hold)
2
ns
1
RMII inputs synchronous to RMII REF_CLK are ERxD1–0, RMII CRS_DV, and ERxER.
tREFCLK
tREFCLKW
RMII_REF_CLK
ERxD1–0
ERxDV
ERxER
tREFCLKIS
tREFCLKIH
Figure 38. 10/100 Ethernet MAC Controller Timing: RMII Receive Signal
Table 61. 10/100 Ethernet MAC Controller Timing: RMII Transmit Signal
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Parameter1
Min
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Max
Min
Max
Unit
7.5
ns
Switching Characteristics
tEREFCLKOV
RMII REF_CLK Rising Edge
to Tx Output Valid (Data Out Valid)
tEREFCLKOH
RMII REF_CLK Rising Edge
2
to Tx Output Invalid (Data Out Hold)
1
8.1
8.1
2
7.5
2
RMII outputs synchronous to RMII REF_CLK are ETxD1–0.
tREFCLK
RMII_REF_CLK
tREFCLKOH
ETxD1–0
ETxEN
tREFCLKOV
Figure 39. 10/100 Ethernet MAC Controller Timing: RMII Transmit Signal
Rev. D |
Page 69 of 88 | July 2013
2
ns
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 62. 10/100 Ethernet MAC Controller Timing: MII/RMII Asynchronous Signal
VDDEXT
1.8V Nominal
Min
Parameter
VDDEXT
2.5 V or 3.3V Nominal
Max
Min
Max
Unit
Timing Requirements
tECOLH
COL Pulse Width High1
tETxCLK × 1.5
tERxCLK × 1.5
tETxCLK × 1.5
tERxCLK × 1.5
ns
tECOLL
COL Pulse Width Low1
tETxCLK × 1.5
tERxCLK × 1.5
tETxCLK × 1.5
tERxCLK × 1.5
ns
tECRSH
CRS Pulse Width High2
tETxCLK × 1.5
tETxCLK × 1.5
ns
tETxCLK × 1.5
tETxCLK × 1.5
ns
tECRSL
CRS Pulse Width Low
2
1
MII/RMII asynchronous signals are COL and CRS. These signals are applicable in both MII and RMII modes. The asynchronous COL input is synchronized separately to
both the ETxCLK and the ERxCLK, and the COL input must have a minimum pulse width high or low at least 1.5 times the period of the slower of the two clocks.
2
The asynchronous CRS input is synchronized to the ETxCLK, and the CRS input must have a minimum pulse width high or low at least 1.5 times the period of ETxCLK.
MIICRS, COL
tECRSH
tECOLH
tECRSL
tECOLL
Figure 40. 10/100 Ethernet MAC Controller Timing: Asynchronous Signal
Table 63. 10/100 Ethernet MAC Controller Timing: MII Station Management
ADSP-BF522/ADSP-BF524/
ADSP-BF526
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Parameter1
Min
Max
Min
Max
ADSP-BF523/ADSP-BF525/
ADSP-BF527
VDDEXT
2.5 V or 3.3V
Nominal
VDDEXT
1.8V Nominal
Min
Max
Min
Max
Unit
Timing Requirements
tMDIOS
MDIO Input Valid to MDC Rising Edge
(Setup)
11.5
11.5
10
10
ns
tMDCIH
MDC Rising Edge to MDIO Input Invalid 11.5
(Hold)
11.5
10
10
ns
Switching Characteristics
tMDCOV
MDC Falling Edge to MDIO Output Valid
tMDCOH
MDC Falling Edge to MDIO Output
Invalid (Hold)
1
25
–1
25
–1
25
–1
25
–1
ns
ns
MDC/MDIO is a 2-wire serial bidirectional port for controlling one or more external PHYs. MDC is an output clock whose minimum period is programmable as a multiple
of the system clock SCLK. MDIO is a bidirectional data line.
Rev. D
|
Page 70 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
MDC (OUTPUT)
tMDCOH
MDIO (OUTPUT)
tMDCOV
MDIO (INPUT)
tMDIOS
tMDCIH
Figure 41. 10/100 Ethernet MAC Controller Timing: MII Station Management
Rev. D |
Page 71 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
JTAG Test And Emulation Port Timing
Table 64 and Figure 42 describe JTAG port operations.
Table 64. JTAG Port Timing
VDDEXT
1.8V Nominal
Min
Parameter
Max
VDDEXT
2.5 V or 3.3V Nominal
Min
Max
Unit
Timing Requirements
tTCK
TCK Period
20
20
ns
tSTAP
TDI, TMS Setup Before TCK High
4
4
ns
tHTAP
TDI, TMS Hold After TCK High
4
4
ns
12
12
ns
5
5
ns
4
4
TCK
tSSYS
System Inputs Setup Before TCK High
1
1
tHSYS
System Inputs Hold After TCK High
tTRSTW
TRST Pulse Width2 (measured in TCK cycles)
Switching Characteristics
TDO Delay from TCK Low
tDTDO
System Outputs Delay After TCK Low
tDSYS
3
1
10
10
ns
12
12
ns
System Inputs = DATA15–0, ARDY, SCL, SDA, PF15–0, PG15–0, PH15–0, RESET, NMI, BMODE3–0.
50 MHz Maximum.
3
System Outputs = DATA15–0, ADDR19–1, ABE1–0, AOE, ARE, AWE, AMS3–0, SRAS, SCAS, SWE, SCKE, CLKOUT, SA10, SMS, SCL, SDA, PF15–0, PG15–0, PH15–0.
2
tTCK
TCK
tSTAP
tHTAP
TMS
TDI
tDTDO
TDO
tSSYS
tHSYS
SYSTEM
INPUTS
tDSYS
SYSTEM
OUTPUTS
Figure 42. JTAG Port Timing
Rev. D |
Page 72 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
OUTPUT DRIVE CURRENTS
Figure 43 through Figure 57 show typical current-voltage characteristics for the output drivers of the ADSP-BF52x processors.
The curves represent the current drive capability of the output
drivers. See Table 10 on Page 23 for information about which
driver type corresponds to a particular ball.
200
160
240
200
VDDEXT = 3.0V @ 105°C
120
80
0
–40
–80
VOL
–120
VDDEXT = 3.0V @ 105°C
120
VOH
40
VDDEXT = 3.6V @ – 40°C
VDDEXT = 3.3V @ 25°C
160
SOURCE CURRENT (mA)
SOURCE CURRENT (mA)
VDDEXT = 3.6V @ – 40°C
VDDEXT = 3.3V @ 25°C
–160
80
VOH
40
0
–40
–80
–120
VOL
–160
–200
–200
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
–240
0
SOURCE VOLTAGE (V)
0.5
1.0
1.5
2.0
2.5
3.0
3.5
SOURCE VOLTAGE (V)
Figure 43. Driver Type A Current (3.3V VDDEXT/VDDMEM)
Figure 46. Driver Type B Current (3.3V VDDEXT/VDDMEM)
160
VDDEXT = 2.75V @ – 40°C
120
160
VDDEXT = 2.5V @ 25°C
VDDEXT = 2.75V @ – 40°C
VDDEXT = 2.25V @ 105°C
120
VDDEXT = 2.5V @ 25°C
80
VDDEXT = 2.25V @ 105°C
40
VOH
0
–40
–80
VOL
–120
SOURCE CURRENT (mA)
SOURCE CURRENT (mA)
80
40
VOH
0
–40
–80
VOL
–120
–160
–160
0
0.5
1.0
1.5
2.0
2.5
–200
0
SOURCE VOLTAGE (V)
0.5
1.0
1.5
2.0
2.5
SOURCE VOLTAGE (V)
Figure 44. Driver Type A Current (2.5V VDDEXT/VDDMEM)
Figure 47. Driver Type B Current (2.5V VDDEXT/VDDMEM)
80
60
VDDEXT = 1.9V @ – 40°C
80
VDDEXT = 1.8V @ 25°C
VDDEXT = 1.7V @ 105°C
60
VDDEXT = 1.9V @ – 40°C
VDDEXT = 1.8V @ 25°C
VDDEXT = 1.7V @ 105°C
40
VOH
20
0
–20
VOL
–40
–60
SOURCE CURRENT (mA)
SOURCE CURRENT (mA)
40
VOH
20
0
–20
–40
VOL
–60
–80
–80
0
0.5
1.0
1.5
–100
0.5
0
SOURCE VOLTAGE (V)
1.0
1.5
SOURCE VOLTAGE (V)
Figure 45. Driver Type A Current (1.8V VDDEXT/VDDMEM)
Figure 48. Driver Type B Current (1.8V VDDEXT/VDDMEM)
Rev. D |
Page 73 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
100
160
120
VDDEXT = 3.3V @ 25°C
60
VDDEXT = 3.0V @ 105°C
40
VOH
20
0
–20
–40
VOL
–60
VDDEXT = 3.3V @ 25°C
VDDEXT = 3.0V @ 105°C
80
SOURCE CURRENT (mA)
SOURCE CURRENT (mA)
VDDEXT = 3.6V @ – 40°C
VDDEXT = 3.6V @ – 40°C
80
VOH
40
0
–40
–80
VOL
–120
–80
–100
–160
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
0.5
1.0
1.5
SOURCE VOLTAGE (V)
Figure 49. Driver Type C Current (3.3V VDDEXT/VDDMEM)
3.0
3.5
120
VDDEXT = 2.75V @ – 40°C
VDDEXT = 2.75V @ – 40°C
100
VDDEXT = 2.5V @ 25°C
VDDEXT = 2.5V @ 25°C
80
VDDEXT = 2.25V @ 105°C
40
VDDEXT = 2.25V @ 105°C
60
20
VOH
0
–20
–40
VOL
SOURCE CURRENT (mA)
SOURCE CURRENT (mA)
2.5
Figure 52. Driver Type D Current (3.3V VDDEXT/VDDMEM)
80
60
2.0
SOURCE VOLTAGE (V)
40
VOH
20
0
–20
–40
–60
VOL
–80
–60
–100
–80
–120
0
0.5
1.0
1.5
2.0
2.5
0
0.5
1.0
SOURCE VOLTAGE (V)
Figure 50. Drive Type C Current (2.5V VDDEXT/VDDMEM)
2.5
60
VDDEXT = 1.9V @ – 40°C
VDDEXT = 1.9V @ – 40°C
VDDEXT = 1.8V @ 25°C
VDDEXT = 1.7V @ 105°C
VDDEXT = 1.8V @ 25°C
VDDEXT = 1.7V @ 105°C
40
VOH
10
0
–10
VOL
–20
SOURCE CURRENT (mA)
20
SOURCE CURRENT (mA)
2.0
Figure 53. Driver Type D Current (2.5V VDDEXT/VDDMEM)
40
30
1.5
SOURCE VOLTAGE (V)
20
VOH
0
–20
VOL
–40
–30
–40
0
0.5
1.0
–60
1.5
0
0.5
SOURCE VOLTAGE (V)
1.0
1.5
SOURCE VOLTAGE (V)
Figure 51. Driver Type C Current (1.8V VDDEXT/VDDMEM)
Rev. D
Figure 54. Driver Type D Current (1.8V VDDEXT/VDDMEM)
|
Page 74 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
TEST CONDITIONS
60
VDDEXT = 3.6V @ – 40°C
50
VDDEXT = 3.3V @ 25°C
40
VDDEXT = 3.0V @ 105°C
SOURCE CURRENT (mA)
30
20
10
0
All Timing Requirements appearing in this data sheet were
measured under the conditions described in this section.
Figure 58 shows the measurement point for AC measurements
(except output enable/disable). The measurement point VMEAS is
VDDEXT/2 or VDDMEM/2 for VDDEXT/VDDMEM (nominal) = 1.8 V/
2.5 V/3.3 V.
–10
–20
–30
INPUT
OR
OUTPUT
VOL
–40
VMEAS
VMEAS
–50
–60
0
0.5
1.0
1.5
2.0
2.5
3.0
Figure 58. Voltage Reference Levels for AC Measurements
(Except Output Enable/Disable)
3.5
SOURCE VOLTAGE (V)
Output Enable Time Measurement
Figure 55. Driver Type E Current (3.3V VDDEXT/VDDMEM)
40
VDDEXT = 2.75V @ – 40°C
30
VDDEXT = 2.5V @ 25°C
VDDEXT = 2.25V @ 105°C
SOURCE CURRENT (mA)
20
10
0
Output balls are considered to be enabled when they have made
a transition from a high impedance state to the point when they
start driving.
The output enable time tENA is the interval from the point when
a reference signal reaches a high or low voltage level to the point
when the output starts driving as shown on the right side of
Figure 59.
–10
REFERENCE
SIGNAL
VOL
–20
–30
tDIS_MEASURED
tDIS
–40
0
0.5
1.0
1.5
2.0
3.0
2.5
3.5
VOH
(MEASURED)
SOURCE VOLTAGE (V)
VOL
(MEASURED)
Figure 56. Driver Type E Current (2.5V VDDEXT/VDDMEM)
tENA_MEASURED
tENA
VOH (MEASURED) ⴚ ⌬V
VOH(MEASURED)
VTRIP(HIGH)
VOL (MEASURED) + ⌬V
VTRIP(LOW)
VOL (MEASURED)
tDECAY
tTRIP
20
VDDEXT = 1.9V @ – 40°C
15
VDDEXT = 1.8V @ 25°C
VDDEXT = 1.7V @ 105°C
OUTPUT STOPS DRIVING
HIGH IMPEDANCE STATE
10
SOURCE CURRENT (mA)
OUTPUT STARTS DRIVING
Figure 59. Output Enable/Disable
5
0
–5
VOL
–10
–15
–20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
SOURCE VOLTAGE (V)
Figure 57. Driver Type E Current (1.8V VDDEXT/VDDMEM)
The time tENA_MEASURED is the interval from when the reference
signal switches to when the output voltage reaches VTRIP(high)
or VTRIP(low). For VDDEXT/VDDMEM (nominal) = 1.8 V, VTRIP
(high) is 1.05 V, and VTRIP (low) is 0.75 V. For VDDEXT/VDDMEM
(nominal) = 2.5 V, VTRIP (high) is 1.5 V and VTRIP (low) is 1.0 V.
For VDDEXT/VDDMEM (nominal) = 3.3 V, VTRIP (high) is 1.9 V, and
VTRIP (low) is 1.4 V. Time tTRIP is the interval from when the output starts driving to when the output reaches the VTRIP(high) or
VTRIP(low) trip voltage.
Time tENA is calculated as shown in the equation:
t ENA = t ENA_MEASURED – t TRIP
If multiple balls (such as the data bus) are enabled, the measurement value is that of the first ball to start driving.
Rev. D |
Page 75 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Output Disable Time Measurement
TESTER PIN ELECTRONICS
Output balls are considered to be disabled when they stop driving, go into a high impedance state, and start to decay from their
output high or low voltage. The output disable time tDIS is the
difference between tDIS_MEASURED and tDECAY as shown on the left
side of Figure 59.
t DIS = t DIS_MEASURED – t DECAY
The time for the voltage on the bus to decay by ΔV is dependent
on the capacitive load CL and the load current IL. This decay
time can be approximated by the equation:
50Ω
VLOAD
T1
DUT
OUTPUT
45Ω
70Ω
ZO = 50Ω (impedance)
TD = 4.04 ± 1.18 ns
50Ω
0.5pF
4pF
2pF
400Ω
t DECAY =  C L V   I L
The time tDECAY is calculated with test loads CL and IL, and with
V equal to 0.25 V for VDDEXT/VDDMEM (nominal) = 2.5 V/3.3 V
and 0.15 V for VDDEXT/VDDMEM (nominal) = 1.8V.
The time tDIS_MEASURED is the interval from when the reference
signal switches, to when the output voltage decays ΔV from the
measured output high or output low voltage.
NOTES:
THE WORST CASE TRANSMISSION LINE DELAY IS SHOWN AND CAN BE USED
FOR THE OUTPUT TIMING ANALYSIS TO REFELECT THE TRANSMISSION LINE
EFFECT AND MUST BE CONSIDERED. THE TRANSMISSION LINE (TD) IS FOR
LOAD ONLY AND DOES NOT AFFECT THE DATA SHEET TIMING SPECIFICATIONS.
ANALOG DEVICES RECOMMENDS USING THE IBIS MODEL TIMING FOR A GIVEN
SYSTEM REQUIREMENT. IF NECESSARY, A SYSTEM MAY INCORPORATE
EXTERNAL DRIVERS TO COMPENSATE FOR ANY TIMING DIFFERENCES.
Figure 60. Equivalent Device Loading for AC Measurements
(Includes All Fixtures)
Example System Hold Time Calculation
Capacitive Loading
Output delays and holds are based on standard capacitive loads
of an average of 6 pF on all balls (see Figure 60). VLOAD is equal
to (VDDEXT/VDDMEM) /2. The graphs of Figure 61 through
Figure 72 show how output rise time varies with capacitance.
The delay and hold specifications given should be derated by a
factor derived from these figures. The graphs in these figures
may not be linear outside the ranges shown.
Rev. D
|
12
RISE AND FALL TIME (10% TO 90%)
To determine the data output hold time in a particular system,
first calculate tDECAY using the equation given above. Choose ΔV
to be the difference between the processor’s output voltage and
the input threshold for the device requiring the hold time. CL is
the total bus capacitance (per data line), and IL is the total leakage or three-state current (per data line). The hold time will be
tDECAY plus the various output disable times as specified in the
Timing Specifications on Page 39 (for example tDSDAT for an
SDRAM write cycle as shown in SDRAM Interface Timing on
Page 47).
10
tRISE
8
tFALL
6
4
2
tRISE = 1.8V @ 25°C
tFALL = 1.8V @ 25°C
0
0
50
100
150
200
LOAD CAPACITANCE (pF)
Figure 61. Driver Type A Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (1.8V VDDEXT/VDDMEM)
Page 76 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
7
7
6
tRISE
5
tFALL
4
3
2
1
tRISE = 2.5V @ 25°C
RISE AND FALL TIME (10% TO 90%)
RISE AND FALL TIME (10% TO 90%)
8
6
5
tRISE
4
tFALL
3
2
1
tRISE = 2.5V @ 25°C
tFALL = 2.5V @ 25°C
tFALL = 2.5V @ 25°C
0
0
50
100
0
200
150
0
50
LOAD CAPACITANCE (pF)
200
150
LOAD CAPACITANCE (pF)
Figure 62. Driver Type A Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (2.5V VDDEXT/VDDMEM)
Figure 65. Driver Type B Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (2.5V VDDEXT/VDDMEM)
6
6
5
tRISE
4
tFALL
3
2
1
tRISE = 3.3V @ 25°C
RISE AND FALL TIME (10% TO 90%)
RISE AND FALL TIME (10% TO 90%)
100
5
tRISE
4
tFALL
3
2
1
tRISE = 3.3V @ 25°C
tFALL = 3.3V @ 25°C
0
tFALL = 3.3V @ 25°C
0
0
50
100
200
150
0
50
LOAD CAPACITANCE (pF)
100
200
150
LOAD CAPACITANCE (pF)
Figure 63. Driver Type A Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (3.3V VDDEXT/VDDMEM)
Figure 66. Driver Type B Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (3.3V VDDEXT/VDDMEM)
9
25
tRISE
7
6
tFALL
5
4
3
2
tRISE = 1.8V @ 25°C
1
RISE AND FALL TIME (10% TO 90%)
RISE AND FALL TIME (10% TO 90%)
8
20
tRISE
15
tFALL
10
5
tRISE = 1.8V @ 25°C
tFALL = 1.8V @ 25°C
0
tFALL = 1.8V @ 25°C
0
0
50
100
150
200
0
LOAD CAPACITANCE (pF)
50
100
150
200
LOAD CAPACITANCE (pF)
Figure 64. Driver Type B Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (1.8V VDDEXT/VDDMEM)
Rev. D |
Figure 67. Driver Type C Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (1.8V VDDEXT/VDDMEM)
Page 77 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
10
9
14
12
tRISE
10
tFALL
8
6
4
2
tRISE = 2.5V @ 25°C
RISE AND FALL TIME (10% TO 90%)
RISE AND FALL TIME (10% TO 90%)
16
100
tFALL
5
4
3
2
tRISE = 2.5V @ 25°C
tFALL = 2.5V @ 25°C
0
200
150
tRISE
6
0
0
50
7
1
tFALL = 2.5V @ 25°C
0
8
50
14
8
12
tRISE
10
8
tFALL
6
4
2
tRISE = 3.3V @ 25°C
RISE AND FALL TIME (10% TO 90%)
RISE AND FALL TIME (10% TO 90%)
200
150
Figure 71. Driver Type D Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (2.5V VDDEXT/VDDMEM)
Figure 68. Driver Type C Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (2.5V VDDEXT/VDDMEM)
7
6
tRISE
5
tFALL
4
3
2
1
tRISE = 3.3V @ 25°C
tFALL = 3.3V @ 25°C
0
tFALL = 3.3V @ 25°C
0
0
50
100
200
150
0
50
LOAD CAPACITANCE (pF)
100
200
150
LOAD CAPACITANCE (pF)
Figure 69. Driver Type C Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (3.3V VDDEXT/VDDMEM)
Figure 72. Driver Type D Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (3.3V VDDEXT/VDDMEM)
9
12
tRISE
10
tFALL
8
6
4
2
tRISE = 1.8V @ 25°C
RISE AND FALL TIME (10% TO 90%)
14
RISE AND FALL TIME (10% TO 90%)
100
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
8
tRISE
7
6
tFALL
5
4
3
2
tRISE = 1.8V @ 25°C
1
tFALL = 1.8V @ 25°C
tFALL = 1.8V @ 25°C
0
0
0
50
100
150
0
200
50
100
150
200
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
Figure 70. Driver Type D Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (1.8V VDDEXT/VDDMEM)
Rev. D
|
Figure 73. Driver Type G Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (1.8V VDDEXT/VDDMEM)
Page 78 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Values of JA are provided for package comparison and printed
circuit board design considerations. JA can be used for a first
order approximation of TJ by the equation:
9
RISE AND FALL TIME (10% TO 90%)
8
7
6
T J = T A +   JA  P D 
tRISE
5
tFALL
where:
4
TA = Ambient temperature (°C)
3
2
tRISE = 2.5V @ 25°C
1
tFALL = 2.5V @ 25°C
0
0
50
100
200
150
LOAD CAPACITANCE (pF)
Figure 74. Driver Type G Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (2.5V VDDEXT/VDDMEM)
9
RISE AND FALL TIME (10% TO 90%)
8
Values of JC are provided for package comparison and printed
circuit board design considerations when an external heat sink
is required.
Values of JB are provided for package comparison and printed
circuit board design considerations.
In Table 66, airflow measurements comply with JEDEC standards JESD51-2 and JESD51-6, and the junction-to-board
measurement complies with JESD51-8. The junction-to-case
measurement complies with MIL-STD-883 (Method 1012.1).
All measurements use a 2S2P JEDEC test board.
Table 65. Thermal Characteristics for BC-208-1 Package
7
tRISE
6
5
tFALL
4
3
2
tRISE = 3.3V @ 25°C
1
tFALL = 3.3V @ 25°C
0
0
50
100
150
200
LOAD CAPACITANCE (pF)
Figure 75. Driver Type G Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (3.3V VDDEXT/VDDMEM)
ENVIRONMENTAL CONDITIONS
To determine the junction temperature on the application
printed circuit board use:
T J = T CASE +   JT  P D 
Parameter
Condition
Typical
Unit
JA
0 linear m/s air flow
23.20
°C/W
JMA
1 linear m/s air flow
20.20
°C/W
JMA
2 linear m/s air flow
19.20
°C/W
JB
13.05
°C/W
JC
6.92
°C/W
JT
0 linear m/s air flow
0.18
°C/W
JT
1 linear m/s air flow
0.27
°C/W
JT
2 linear m/s air flow
0.32
°C/W
Table 66. Thermal Characteristics for BC-289-2 Package
Parameter
Condition
Typical
Unit
JA
0 linear m/s air flow
34.5
°C/W
JMA
1 linear m/s air flow
31.1
°C/W
JMA
2 linear m/s air flow
29.8
°C/W
JB
20.3
°C/W
JC
8.8
°C/W
where:
JT
0 linear m/s air flow
0.24
°C/W
TJ = Junction temperature (°C)
JT
1 linear m/s air flow
0.44
°C/W
JT
2 linear m/s air flow
0.53
°C/W
TCASE = Case temperature (°C) measured by customer at top
center of package.
JT = From Table 66
PD = Power dissipation — For a description, see Total Power
Dissipation on Page 35.
Rev. D |
Page 79 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
289-BALL CSP_BGA BALL ASSIGNMENT
Table 67 lists the CSP_BGA balls by signal mnemonic.
Table 68 on Page 81 lists the CSP_BGA by ball number.
Table 67. 289-Ball CSP_BGA Ball Assignment (Alphabetically by Signal)
Ball
Ball
Ball
Ball
Ball
Ball
Ball
Signal
No. Signal
No. Signal No. Signal No. Signal
No. Signal
No. Signal
No.
T2
GND M10 NC
D23 PH0
A11 USB_XO AA23 VDDINT
R8
ABE0/SDQM0 AB9 DATA6
T1
GND M11 NC
E22 PH1
A12 VDDEXT
G7 VDDINT
R16
ABE1/SDQM1 AC9 DATA7
ADDR1
AB8 DATA8
R1
GND M12 NC
E23 PH2
A13 VDDEXT
G8 VDDINT
T8
G9 VDDINT
T9
ADDR2
AC8 DATA9
P1
GND M13 NC
F22 PH3
B14 VDDEXT
G10 VDDINT
T10
ADDR3
AB7 DATA10
P2
GND M14 NC
F23 PH4
A14 VDDEXT
ADDR4
AC7 DATA11
R2
GND M15 NC
G22 PH5
K23 VDDEXT
G11 VDDINT
T11
G12 VDDINT
T12
ADDR5
AC6 DATA12
N1 GND N9 NC
H23 PH6
K22 VDDEXT
G13 VDDINT
T13
ADDR6
AB6 DATA13
N2 GND N10 NC
J23 PH7
L23 VDDEXT
ADDR7
AB4 DATA14
M2 GND N11 NMI
U22 PH8
L22 VDDEXT
G14 VDDINT
T14
G15 VDDINT
T15
ADDR8
AB5 DATA15
M1 GND N12 VPPOTP AB11 PH9
T23 VDDEXT
H7 VDDINT
T16
ADDR9
AC5 EMU
J2
GND N13 PF0
A7 PH10
M22 VDDEXT
ADDR10
AC4 EXT_WAKE0 AC19 GND N14 PF1
B8 PH11
R22 VDDEXT
J17 VDDMEM
J7
K17 VDDMEM
K7
ADDR11
AB3 GND
A1 GND N15 PF2
A8 PH12
M23 VDDEXT
L17 VDDMEM
L7
ADDR12
AC3 GND
A23 GND P9
PF3
B9 PH13
N22 VDDEXT
ADDR13
AB2 GND
B6 GND P10 PF4
B11 PH14
N23 VDDEXT
M17 VDDMEM
M7
G16 GND P11 PF5
B10 PH15
P22 VDDEXT
N17 VDDMEM
N7
ADDR14
AC2 GND1
P17 VDDMEM
P7
ADDR15
AA2 GND
G17 GND P12 PF6
B12 PPI_CLK/TMRCLK A6 VDDEXT
ADDR16
W2 GND1
H17 GND P13 PF7
B13 PPI_FS1/TMR0
B7 VDDEXT
R17 VDDMEM
R7
V22 VDDEXT
T17 VDDMEM
T7
ADDR17
Y2 GND
H22 GND P14 PF8
B16 RESET
ADDR18
AA1 GND1
J22 GND P15 PF9
A20 RTXI
U23 VDDEXT
U17 VDDMEM
U7
B5 VDDMEM
U8
ADDR19
AB1 GND
J9
GND R9 PF10
B15 RTXO
V23 VDDINT
AC17 GND
J10 GND R10 PF11
B17 SA10
AC10 VDDINT
H8 VDDMEM
U9
AMS0
AMS1
AB16 GND
J11 GND R11 PF12
B18 SCAS
AC11 VDDINT
H9 VDDMEM
U10
AC16 GND
J12 GND R12 PF13
B19 SCKE
AB13 VDDINT
H10 VDDMEM
U11
AMS2
AB15 GND
J13 GND R13 PF14
A9 SCL
B22 VDDINT
H11 VDDMEM
U12
AMS3
AOE
AC15 GND
J14 GND R14 PF15
A10 SDA
C22 VDDINT
H12 VDDMEM
U13
AC13 VDDINT
H13 VDDMEM
U14
ARDY
AC14 GND
J15 GND R15 PG0
H2 SMS
AB17 GND
K9 GND T22 PG1
G1 SRAS
AB12 VDDINT
H14 VDDMEM
U15
ARE
AWE
AB14 GND
K10 GND AC1 PG2
H1 SS/PG
AC20 VDDINT
H15 VDDMEM
U16
AB10 VDDINT
H16 VDDOTP
AC12
BMODE0
G2 GND
K11 GND AC23 PG3
F1
SWE
J8
VDDRTC
W23
BMODE1
F2
GND
K12 NC
A15 PG4
D1 TCK
L1
VDDINT
BMODE2
E1
GND
K13 NC
A16 PG5
D2 TDI
J1
VDDINT
J16 VDDUSB
W22
K8 VDDUSB
Y23
BMODE3
E2
GND
K14 NC
A17 PG6
C2 TDO
K1 VDDINT
K16 NC
G23
CLKBUF
AB19 GND
K15 NC
A18 PG7
B1 TMS
L2
VDDINT
CLKIN
R23 GND
L9
NC
A19 PG8
C1 TRST
K2 VDDINT
L8
VROUT/EXT_WAKE1 AC18
L16 VRSEL/VDDEXT
AB22
CLKOUT
AB18 GND
L10 NC
A21 PG9
B2 USB_DM
AB21 VDDINT
M8 XTAL
P23
DATA0
Y1 GND
L11 NC
A22 PG10 B4 USB_DP
AA22 VDDINT
DATA1
V2 GND
L12 NC
B20 PG11 B3 USB_ID
Y22 VDDINT
M16
N8
DATA2
W1 GND
L13 NC
B21 PG12 A2 USB_RSET
AC21 VDDINT
N16
DATA3
U2 GND
L14 NC
B23 PG13 A3 USB_VBUS
AB20 VDDINT
DATA4
V1 GND
L15 NC
C23 PG14 A4 USB_VREF
AC22 VDDINT
P8
P16
DATA5
U1 GND
M9 NC
D22 PG15 A5 USB_XI
AB23 VDDINT
NOTE: In this table, BOLD TYPE indicates the sole signal/function for that ball on ADSP-BF522/ADSP-BF524/ADSP-BF526 processors.
1
For ADSP-BF52xC compatibility, connect this ball to VDDEXT.
Rev. D
|
Page 80 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 68. 289-Ball CSP_BGA Ball Assignment (Numerically by Ball Number)
Ball
Ball
Ball
Ball
Ball
Ball
Ball
No. Signal
No. Signal No. Signal
No. Signal
No. Signal
No. Signal
No. Signal
A1 GND
B20 NC
H12 VDDINT
L9
GND
P2
DATA10 T22 GND
AB10 SWE
A2 PG12
B21 NC
H13 VDDINT
L10 GND
P7
VDDMEM
T23 PH9
AB11 VPPOTP
L11 GND
P8
VDDINT
U1 DATA5
AB12 SRAS
A3 PG13
B22 SCL
H14 VDDINT
A4 PG14
B23 NC
H15 VDDINT
L12 GND
P9
GND
U2 DATA3
AB13 SCKE
L13 GND
P10 GND
U7 VDDMEM
AB14 AWE
A5 PG15
C1 PG8
H16 VDDINT
A6 PPI_CLK/TMRCLK C2 PG6
H17 GND1
L14 GND
P11 GND
U8 VDDMEM
AB15 AMS3
A7 PF0
C22 SDA
H22 GND
L15 GND
P12 GND
U9 VDDMEM
AB16 AMS1
A8 PF2
C23 NC
H23 NC
L16 VDDINT
P13 GND
U10 VDDMEM
AB17 ARE
A9 PF14
D1 PG4
J1
TDI
L17 VDDEXT
P14 GND
U11 VDDMEM
AB18 CLKOUT
A10 PF15
D2 PG5
J2
EMU
L22 PH8
P15 GND
U12 VDDMEM
AB19 CLKBUF
L23 PH7
P16 VDDINT
U13 VDDMEM
AB20 USB_VBUS
A11 PH0
D22 NC
J7
VDDMEM
M1 DATA15 P17 VDDEXT
U14 VDDMEM
AB21 USB_DM
A12 PH1
D23 NC
J8
VDDINT
A13 PH2
E1
BMODE2 J9
GND
M2 DATA14 P22 PH15
U15 VDDMEM
AB22 VRSEL/VDDEXT
A14 PH4
E2
BMODE3 J10 GND
M7 VDDMEM
P23 XTAL
U16 VDDMEM
AB23 USB_XI
R1
DATA8
U17 VDDEXT
AC1 GND
A15 NC
E22 NC
J11 GND
M8 VDDINT
A16 NC
E23 NC
J12 GND
M9 GND
R2
DATA11 U22 NMI
AC2 ADDR14
U23 RTXI
AC3 ADDR12
A17 NC
F1
PG3
J13 GND
M10 GND
R7
VDDMEM
V1 DATA4
AC4 ADDR10
A18 NC
F2
BMODE1 J14 GND
M11 GND
R8
VDDINT
A19 NC
F22 NC
J15 GND
M12 GND
R9
GND
V2 DATA1
AC5 ADDR9
A20 PF9
F23 NC
J16 VDDINT
M13 GND
R10 GND
V22 RESET
AC6 ADDR5
M14 GND
R11 GND
V23 RTXO
AC7 ADDR4
A21 NC
G1 PG1
J17 VDDEXT
A22 NC
G2 BMODE0 J22 GND1
M15 GND
R12 GND
W1 DATA2
AC8 ADDR2
J23 NC
M16 VDDINT
R13 GND
W2 ADDR16
AC9 ABE1/SDQM1
A23 GND
G7 VDDEXT
B1
PG7
G8 VDDEXT
K1
TDO
M17 VDDEXT
R14 GND
W22 VDDUSB
AC10 SA10
K2
TRST
M22 PH10
R15 GND
W23 VDDRTC
AC11 SCAS
B2
PG9
G9 VDDEXT
B3
PG11
G10 VDDEXT
K7
VDDMEM
M23 PH12
R16 VDDINT
Y1
DATA0
AC12 VDDOTP
B4
PG10
G11 VDDEXT
K8
VDDINT
N1 DATA12 R17 VDDEXT
Y2
ADDR17
AC13 SMS
B5
VDDINT
G12 VDDEXT
K9
GND
N2 DATA13 R22 PH11
Y22 USB_ID
AC14 ARDY
K10 GND
N7 VDDMEM
R23 CLKIN
Y23 VDDUSB
AC15 AOE
B6
GND
G13 VDDEXT
B7
PPI_FS1/TMR0
G14 VDDEXT
K11 GND
N8 VDDINT
T1
DATA7
AA1 ADDR18
AC16 AMS2
B8
PF1
G15 VDDEXT
K12 GND
N9 GND
T2
DATA6
AA2 ADDR15
AC17 AMS0
1
B9
PF3
G16 GND
K13 GND
N10 GND
T7
VDDMEM
AA22 USB_DP
AC18 VROUT/EXT_WAKE1
B10 PF5
G17 GND
K14 GND
N11 GND
T8
VDDINT
AA23 USB_XO
AC19 EXT_WAKE0
AB1 ADDR19
AC20 SS/PG
B11 PF4
G22 NC
K15 GND
N12 GND
T9
VDDINT
B12 PF6
G23 NC
K16 VDDINT
N13 GND
T10 VDDINT
AB2 ADDR13
AC21 USB_RSET
B13 PF7
H1 PG2
K17 VDDEXT
N14 GND
T11 VDDINT
AB3 ADDR11
AC22 USB_VREF
AB4 ADDR7
AC23 GND
B14 PH3
H2 PG0
K22 PH6
N15 GND
T12 VDDINT
K23 PH5
N16 VDDINT
T13 VDDINT
AB5 ADDR8
B15 PF10
H7 VDDEXT
B16 PF8
H8 VDDINT
L1
TCK
N17 VDDEXT
T14 VDDINT
AB6 ADDR6
L2
TMS
N22 PH13
T15 VDDINT
AB7 ADDR3
B17 PF11
H9 VDDINT
L7
VDDMEM
N23 PH14
T16 VDDINT
AB8 ADDR1
B18 PF12
H10 VDDINT
B19 PF13
H11 VDDINT
L8
VDDINT
P1
DATA9
T17 VDDEXT
AB9 ABE0/SDQM0
NOTE: In this table, BOLD TYPE indicates the sole signal/function for that ball on ADSP-BF522/ADSP-BF524/ADSP-BF526 processors.
1
For ADSP-BF52xC compatibility, connect this ball to VDDEXT.
Rev. D |
Page 81 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Figure 76 shows the top view of the BC-289-2 CSP_BGA ball
configuration. Figure 77 shows the bottom view of the
BC-289-2 CSP_BGA ball configuration.
A1 BALL
PAD CORNER
A
B
C
D
E
F
G
H
J
K
L
TOP VIEW
M
N
P
KEY:
R
V
DDINT
GND
T
NC
U
V
V
DDEXT
I/O
V
W
DDMEM
Y
AA
AB
AC
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Figure 76. 289-Ball CSP_BGA Ball Configuration (Top View)
A1 BALL
PAD CORNER
A
B
C
D
E
BOTTOM VIEW
F
G
H
KEY:
J
K
L
V
GND
NC
V
I/O
V
DDINT
M
N
P
DDEXT
R
T
U
V
W
Y
AA
AB
AC
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
Figure 77. 289-Ball CSP_BGA Ball Configuration (Bottom View)
Rev. D
|
Page 82 of 88 | July 2013
DDMEM
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
208-BALL CSP_BGA BALL ASSIGNMENT
Table 69 lists the CSP_BGA balls by signal mnemonic.
Table 70 on Page 84 lists the CSP_BGA by ball number.
Table 69. 208-Ball CSP_BGA Ball Assignment (Alphabetically by Signal)
Signal
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
ABE0/SDQM0 V19
CLKOUT
K20
GND
K11
PF13
A5
PPI_CLK/TMRCLK
G2
VDDEXT
J8
ABE1/SDQM1 V20
DATA0
Y8
GND
K12
PF14
B6
PPI_FS1/TMR0
F2
VDDEXT
K7
Signal
Ball
No.
ADDR1
W20 DATA1
W8
GND
K13
PF15
A6
RESET
B18
VDDEXT
K8
ADDR2
W19 DATA2
Y7
GND
L9
PG0
R2
RTXI
A14
VDDEXT
L7
ADDR3
Y19
ADDR4
W18 DATA4
DATA3
DATA5
W7
GND
L10
PG1
P1
RTXO
A15
VDDINT
G12
Y6
GND
L11
PG2
P2
SA10
U19
VDDINT
G13
ADDR5
Y18
W6
GND
L12
PG3
N1
SCAS
U20
VDDINT
G14
ADDR6
W17 DATA6
Y5
GND
L13
PG4
N2
SCKE
P20
VDDINT
H14
ADDR7
Y17
W5
GND
M9
PG5
M1
SCL
A4
VDDINT
J14
ADDR8
W16 DATA8
Y4
GND
M10 PG6
M2
SDA
B4
VDDINT
K14
ADDR9
Y16
W4
GND
M11 PG7
L1
SMS
R19
VDDINT
L14
ADDR10
W15 DATA10
Y3
GND
M12 PG8
L2
SRAS
T19
VDDINT
M14
ADDR11
Y15
W3
GND
M13 PG9
K1
SS/PG
G19
VDDINT
N14
ADDR12
W14 DATA12
Y2
GND
N9
K2
SWE
T20
VDDINT
P12
DATA7
DATA9
DATA11
PG10
ADDR13
Y14
DATA13
W2
GND
N10
PG11
J1
TCK
V2
VDDINT
P13
ADDR14
W13 DATA14
W1
GND
N11
PG12
J2
TDI
R1
VDDINT
P14
ADDR15
Y13
V1
GND
N12
PG13
H1
TDO
T1
VDDMEM
L8
ADDR16
W12 EMU
T2
GND
N13
PG14
H2
TMS
U2
VDDMEM
M7
ADDR17
Y12
J20
GND
Y1
PG15
G1
TRST
U1
VDDMEM
M8
ADDR18
W11 GND
A1
GND
Y20
PH0
A7
USB_DM
F20
VDDMEM
N7
ADDR19
Y11
GND
A17
NMI
B19
PH1
B7
USB_DP
E20
VDDMEM
N8
AMS0
J19
GND
A20
VPPOTP
L19
PH2
A8
USB_ID
C20
VDDMEM
P7
AMS1
K19
GND
B20
PF0
F1
PH3
B8
USB_RSET
D20
VDDMEM
P8
AMS2
M19 GND
H9
PF1
E1
PH4
A9
USB_VBUS
E19
VDDMEM
P9
AMS3
L20
GND
H10
PF2
E2
PH5
B9
USB_VREF
H19
VDDMEM
P10
AOE
N20
GND
H11
PF3
D1
PH6
B10
USB_XI
A19
VDDMEM
P11
ARDY
P19
GND
H12
PF4
D2
PH7
B11
USB_XO
A18
VDDOTP
R20
ARE
M20 GND
H13
PF5
C1
PH8
A12
VDDEXT
G7
VDDRTC
A16
AWE
N19
GND
J9
PF6
C2
PH9
B12
VDDEXT
G8
VDDUSB
D19
BMODE0
Y10
GND
J10
PF7
B1
PH10
A13
VDDEXT
G9
VDDUSB
G20
DATA15
EXT_WAKE0
BMODE1
W10 GND
J11
PF8
B2
PH11
B13
VDDEXT
G10
VROUT/EXT_WAKE1
H20
BMODE2
Y9
GND
J12
PF9
A2
PH12
B14
VDDEXT
G11
VRSEL/VDDEXT
F19
BMODE3
W9
GND
J13
PF10
B3
PH13
B15
VDDEXT
H7
XTAL
A10
CLKBUF
C19
GND
K9
PF11
A3
PH14
B16
VDDEXT
H8
CLKIN
A11
GND
K10
PF12
B5
PH15
B17
VDDEXT
J7
NOTE: In this table, BOLD TYPE indicates the sole signal/function for that ball on ADSP-BF522/ADSP-BF524/ADSP-BF526 processors.
Rev. D |
Page 83 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Table 70. 208-Ball CSP_BGA Ball Assignment (Numerically by Ball Number)
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
Signal
Ball
No.
Signal
A1
GND
B16
PH14
H7
VDDEXT
L2
PG8
P1
PG1
W8
DATA1
A2
PF9
B17
PH15
H8
VDDEXT
L7
VDDEXT
P2
PG2
W9
BMODE3
A3
PF11
B18
RESET
H9
GND
L8
VDDMEM
P7
VDDMEM
W10 BMODE1
A4
SCL
B19
NMI
H10
GND
L9
GND
P8
VDDMEM
W11 ADDR18
A5
PF13
B20
GND
H11
GND
L10
GND
P9
VDDMEM
W12 ADDR16
A6
PF15
C1
PF5
H12
GND
L11
GND
P10
VDDMEM
W13 ADDR14
A7
PH0
C2
PF6
H13
GND
L12
GND
P11
VDDMEM
W14 ADDR12
A8
PH2
C19
CLKBUF
H14
VDDINT
L13
GND
P12
VDDINT
W15 ADDR10
A9
PH4
C20
USB_ID
H19
USB_VREF
L14
VDDINT
P13
VDDINT
W16 ADDR8
A10
XTAL
D1
PF3
H20
VROUT/EXT_WAKE1
L19
VPPOTP
P14
VDDINT
W17 ADDR6
A11
CLKIN
D2
PF4
J1
PG11
L20
AMS3
P19
ARDY
W18 ADDR4
A12
PH8
D19
VDDUSB
J2
PG12
M1
PG5
P20
SCKE
W19 ADDR2
A13
PH10
D20
USB_RSET
J7
VDDEXT
M2
PG6
R1
TDI
W20 ADDR1
A14
RTXI
E1
PF1
J8
VDDEXT
M7
VDDMEM
R2
PG0
Y1
GND
A15
RTXO
E2
PF2
J9
GND
M8
VDDMEM
R19
SMS
Y2
DATA12
GND
A16
VDDRTC
E19
USB_VBUS
J10
GND
M9
R20
VDDOTP
Y3
DATA10
A17
GND
E20
USB_DP
J11
GND
M10 GND
T1
TDO
Y4
DATA8
A18
USB_XO
F1
PF0
J12
GND
M11 GND
T2
EMU
Y5
DATA6
A19
USB_XI
F2
PPI_FS1/TMR0
J13
GND
M12 GND
T19
SRAS
Y6
DATA4
A20
GND
F19
VRSEL/VDDEXT
J14
VDDINT
M13 GND
T20
SWE
Y7
DATA2
B1
PF7
F20
USB_DM
J19
AMS0
M14 VDDINT
U1
TRST
Y8
DATA0
B2
PF8
G1
PG15
J20
EXT_WAKE0
M19 AMS2
U2
TMS
Y9
BMODE2
B3
PF10
G2
PPI_CLK/TMRCLK
K1
PG9
M20 ARE
U19
SA10
Y10
BMODE0
B4
SDA
G7
VDDEXT
K2
PG10
N1
PG3
U20
SCAS
Y11
ADDR19
B5
PF12
G8
VDDEXT
K7
VDDEXT
N2
PG4
V1
DATA15
Y12
ADDR17
B6
PF14
G9
VDDEXT
K8
VDDEXT
N7
VDDMEM
V2
TCK
Y13
ADDR15
B7
PH1
G10
VDDEXT
K9
GND
N8
VDDMEM
V19
ABE0/SDQM0
Y14
ADDR13
B8
PH3
G11
VDDEXT
K10
GND
N9
GND
V20
ABE1/SDQM1
Y15
ADDR11
B9
PH5
G12
VDDINT
K11
GND
N10
GND
W1
DATA14
Y16
ADDR9
B10
PH6
G13
VDDINT
K12
GND
N11
GND
W2
DATA13
Y17
ADDR7
B11
PH7
G14
VDDINT
K13
GND
N12
GND
W3
DATA11
Y18
ADDR5
B12
PH9
G19
SS/PG
K14
VDDINT
N13
GND
W4
DATA9
Y19
ADDR3
B13
PH11
G20
VDDUSB
K19
AMS1
N14
VDDINT
W5
DATA7
Y20
GND
B14
PH12
H1
PG13
K20
CLKOUT
N19
AWE
W6
DATA5
B15
PH13
H2
PG14
L1
PG7
N20
AOE
W7
DATA3
NOTE: In this table, BOLD TYPE indicates the sole signal/function for that ball on ADSP-BF522/ADSP-BF524/ADSP-BF526 processors.
Rev. D
|
Page 84 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Figure 78 shows the top view of the CSP_BGA ball configuration. Figure 79 shows the bottom view of the CSP_BGA
ball configuration.
A1 BALL
PAD CORNER
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
TOP VIEW
KEY:
VDDINT
GND
VDDEXT
I/O
VDDMEM
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
Figure 78. 208-Ball CSP_BGA Ball Configuration (Top View)
A1 BALL
PAD CORNER
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
BOTTOM VIEW
KEY:
VDDINT
GND
VDDEXT
I/O
VDDMEM
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Figure 79. 208-Ball CSP_BGA Ball Configuration (Bottom View)
Rev. D |
Page 85 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
OUTLINE DIMENSIONS
Dimensions in the outline dimension figures (Figure 80 and
Figure 81) are shown in millimeters.
A1 BALL
CORNER
12.00 BSC SQ
22 20 18 16 14 12 10 8 6 4 2
23 21 19 17 15 13 11 9 7 5 3 1
A
C
E
G
11.00
BSC SQ
J
L
N
R
0.50
BSC
U
W
B
D
F
H
K
M
P
T
V
Y
AA
AB
AC
TOP VIEW
BOTTOM VIEW
DETAIL A
1.40
1.26
1.11
DETAIL A
0.20 MIN
0.35
COPLANARITY
0.08
0.30
0.25
BALL DIAMETER
SEATING
PLANE
*COMPLIANT WITH JEDEC STANDARD MO-275-GGCE-1
Figure 80. 289-Ball CSP_BGA (BC-289-2)
A1 BALL
CORNER
17.10
17.00 SQ
16.90
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
15.20
BSC SQ
0.80
BSC
BOTTOM VIEW
TOP VIEW
*1.75
1.61
1.46
A1 BALL
CORNER
20 18 16 14 12 10 8 6 4 2
19 17 15 13 11 9 7 5 3 1
DETAIL A
DETAIL A
0.35 NOM
0.30 MIN
SEATING
PLANE
0.50
0.45
0.40
BALL DIAMETER
*COMPLIANT TO JEDEC STANDARDS MO-275-MMAB-1 WITH
EXCEPTION TO PACKAGE HEIGHT AND THICKNESS.
Figure 81. 208-Ball CSP_BGA (BC-208-2)
Rev. D
|
Page 86 of 88 | July 2013
*1.36
1.26
1.16
COPLANARITY
0.12
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
SURFACE-MOUNT DESIGN
Table 71 is provided as an aid to PCB design. For industry-standard design recommendations, refer to IPC-7351, Generic
Requirements for Surface Mount Design and Land Pattern
Standard.
Table 71. Surface-Mount Design Supplement
Package
289-Ball CSP_BGA
208-Ball CSP_BGA
Package Ball Attach Type
Solder Mask Defined
Solder Mask Defined
Package Solder Mask
Opening
0.26 mm diameter
0.40 mm diameter
Package Ball Pad Size
0.35 mm diameter
0.50 mm diameter
AUTOMOTIVE PRODUCTS
The ADBF525W model is available with controlled manufacturing to support the quality and reliability requirements of
automotive applications. Note that these automotive models
may have specifications that differ from the commercial models
and designers should review the product Specifications section
of this data sheet carefully. Only the automotive grade products
shown in Table 72 are available for use in automotive applications. Contact your local ADI account representative for specific
product ordering information and to obtain the specific automotive Reliability reports for these models.
Table 72. Automotive Products
Automotive Models1, 2
ADBF525WBBCZ4xx
ADBF525WBBCZ5xx
ADBF525WYBCZxxx
Temperature
Range3
–40°C to +85°C
–40°C to +85°C
–40°C to +105°C
Package Description
208-Ball CSP_BGA
208-Ball CSP_BGA
208-Ball CSP_BGA
1
Package
Option
BC-208-2
BC-208-2
BC-208-2
Instruction
Rate (Max)
400 MHz
533 MHz
For product details, please contact your
ADI account representative.
Z = RoHS Compliant Part.
The information indicated by x in the model number will be provided by your ADI account representative.
3
Referenced temperature is ambient temperature. The ambient temperature is not a specification. Please see Operating Conditions for ADSP-BF523/ADSP-BF525/
ADSP-BF527 Processors on Page 30 for junction temperature (TJ) specification which is the only temperature specification.
2
Rev. D |
Page 87 of 88 | July 2013
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
ORDERING GUIDE
Model1
Temperature
Range2
Instruction
Rate (Max)
Package Description
Package
Option
ADSP-BF522BBCZ-3A
–40°C to +85°C
300 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF522BBCZ-4A
–40°C to +85°C
400 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF522KBCZ-3
0°C to +70°C
300 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF522KBCZ-4
0°C to +70°C
400 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF523BBCZ-5A
–40°C to +85°C
533 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF523KBCZ-5
0°C to +70°C
533 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF523KBCZ-6
0°C to +70°C
600 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF523KBCZ-6A
0°C to +70°C
600 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF524BBCZ-3A
–40°C to +85°C
300 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF524BBCZ-4A
–40°C to +85°C
400 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF524KBCZ-3
0°C to +70°C
300 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF524KBCZ-4
0°C to +70°C
400 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF525ABCZ-5
–40°C to +70°C
500 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF525ABCZ-6
–40°C to +70°C
600 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF525BBCZ-5A
–40°C to +85°C
533 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF525KBCZ-5
0°C to +70°C
533 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF525KBCZ-6
0°C to +70°C
600 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF525KBCZ-6A
0°C to +70°C
600 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF526BBCZ-3A
–40°C to +85°C
300 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF526BBCZ-4A
–40°C to +85°C
400 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF526KBCZ-3
0°C to +70°C
300 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF526KBCZ-4
0°C to +70°C
400 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF527BBCZ-5A
–40°C to +85°C
533 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
ADSP-BF527KBCZ-5
0°C to +70°C
533 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF527KBCZ-6
0°C to +70°C
600 MHz
289-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-289-2
ADSP-BF527KBCZ-6A
0°C to +70°C
600 MHz
208-Ball Chip Scale Package Ball Grid Array (CSP_BGA)
BC-208-2
1
2
Z = RoHS Compliant Part.
Referenced temperature is ambient temperature. The ambient temperature is not a specification. Please see Operating Conditions for ADSP-BF522/ADSP-BF524/ADSP-BF526
Processors on Page 28 and Operating Conditions for ADSP-BF523/ADSP-BF525/ADSP-BF527 Processors on Page 30 for junction temperature (TJ) specification which is
the only temperature specification.
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06675-0-7/13(D)
Rev. D
|
Page 88 of 88 | July 2013
Similar pages