LINER LT1008 Picoamp input current, microvolt offset, low noise op amp Datasheet

LT1008
Picoamp Input Current,
Microvolt Offset,
Low Noise Op Amp
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
Guaranteed Bias Current
TA = 25°C: 100pA Max
TA = – 55°C to 125°C: 600pA Max
Guaranteed Offset Voltage: 120μV Max
Guaranteed Drift: 1.5μV/°C Max
Low Noise, 0.1Hz to 10Hz: 0.5μVP-P
Guaranteed Low Supply Current: 600μA Max
Guaranteed CMRR: 114dB Min
Guaranteed PSRR: 114dB Min
Guaranteed Voltage Gain with 5mA Load Current
Available in 8-Lead PDIP and SO Packages
U
APPLICATIO S
■
■
■
■
■
■
■
Precision Instrumentation
Charge Integrators
Wide Dynamic Range Logarithmic Amplifiers
Light Meters
Low Frequency Active Filters
Standard Cell Buffers
Thermocouple Amplifiers
The LT®1008 is a universal precision operational amplifier
that can be used in practically all precision applications.
The LT1008 combines for the first time, picoampere bias
currents (which are maintained over the full – 55°C to
125°C temperature range), microvolt offset voltage (and
low drift with time and temperature), low voltage and
current noise, and low power dissipation. Extremely high
common mode and power supply rejection ratios, and the
ability to deliver 5mA load current with high voltage gain
round out the LT1008’s superb precision specifications.
The all around excellence of the LT1008 eliminates the
necessity of the time consuming error analysis procedure
of precision system design in many applications; the
LT1008 can be stocked as the universal precision op amp.
The LT1008 is externally compensated with a single capacitor for additional flexibility in shaping the frequency
response of the amplifier. It plugs into and upgrades all
standard LM108A/LM308A applications. For an internally
compensated version with even lower offset voltage but
otherwise similar performance see the LT1012.
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Input Amplifier for 4.5 Digit Voltmeter
Input Bias Current vs Temperature
100
2
INPUT
0.1V
1V
100k
5%
–
1
15V
7
3
+
LT1008
4
9M
6
9k*
1k*
10V
100V
10V
100V
–15V
900k
1000V TO 1V FULL-SCALE
ANALOG-TO-DIGITAL
CONVERTER
*RATIO MATCH ±0.01%
90k
1000V
10k
0.1V
1V
8
FN507
ALLEN BRADLEY
DECADE VOLTAGE DIVIDER
THIS APPLICATION REQUIRES LOW
BIAS CURRENT AND OFFSET VOLTAGE,
LOW NOISE AND LOW DRIFT WITH
TIME AND TEMPERATURE
1008 TA01
INPUT BIAS CURRENT (pA)
1000pF
50
UNDERCANCELLED UNIT
0
OVERCANCELLED UNIT
–50
–100
–150
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
1008 TA02
1008fb
1
LT1008
W W
W
AXI U
U
ABSOLUTE
RATI GS (Note 1)
Supply Voltage ...................................................... ±20V
Differential Input Current (Note 2) ..................... ±10mA
Input Voltage ........................................................ ±20V
Output Short-Circuit Duration ......................... Indefinite
Storage Temperature Range ................. – 65°C to 150°C
Operating Temperature Range
LT1008M (OBSOLETE) ............... – 55°C to 125°C
LT1008C ................................................. 0°C to 70°C
LT1008I ............................................. – 40°C to 85°C
Lead Temperature (Soldering, 10 sec).................. 300°C
U
U
W
PACKAGE/ORDER I FOR ATIO
TOP VIEW
TOP VIEW
COMP2
8
COMP1 1
TOP VIEW
7 V+
–
+
–IN 2
6 OUT
COMP1 1
8
COMP2
–IN 2
7
V+
COMP1 1
8
COMP2
7
V+
+IN 3
6
OUT
–IN 2
V– 4
5
NC
+IN 3
6
OUT
V– 4
5
NC
5 NC
+IN 3
4
N8 PACKAGE
8-LEAD PDIP
TJMAX = 150°C, θJA = 130°C/W
– (CASE)
V
H PACKAGE
8-LEAD TO-5 METAL CAN
TJMAX = 150°C, θJA = 150°C/W, θJC = 45°C/W
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 190°C/W
J8 PACKAGE 8-LEAD CERDIP
TJMAX = 150°C, θJA = 100°C/W
ORDER PART
NUMBER
ORDER PART
NUMBER
ORDER PART
NUMBER
ORDER PART
NUMBER
S8 PART
MARKING
LT1008MH
LT1008CH
LT1008MJ8
LT1008CJ8
LT1008CN8
LT1008IN8
LT1008S8
1008
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
OBSOLETE PACKAGES
Consider N8 or S8 Package for Alternate Source
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
SYMBOL
PARAMETER
VOS
Input Offset Voltage
VS = ±15V, VCM = 0V, TA = 25°C, unless otherwise noted.
CONDITIONS
LT1008M/I
MIN TYP MAX
30
40
(Note 3)
IOS
Long-Term Input Offset Voltage Stability
0.3
Input Offset Current
(Note 3)
30
40
(Note 3)
Input Noise Voltage
MIN
120
180
LT1008C
TYP MAX
30
40
120
180
100
150
pA
pA
±30 ±100
±40 ±150
±30 ±100
±40 ±150
pA
pA
0.1Hz to 10Hz
0.5
0.5
Input Noise Voltage Density
fO = 10Hz (Note 4)
fO = 1000Hz (Note 5)
17
14
in
Input Noise Current Density
fO = 10Hz
20
AVOL
Large-Signal Voltage Gain
VOUT = ±12V, RL ≥ 10k
VOUT = ±10V, RL ≥ 2k
IB
en
Input Bias Current
200
120
2000
600
30
40
μV
μV
μV/Month
0.3
100
150
UNITS
30
22
17
14
200
120
μVP-P
30
22
nV√Hz
nV/√Hz
20
fA/√Hz
2000
600
V/mV
V/mV
1008fb
2
LT1008
ELECTRICAL CHARACTERISTICS
VS = ±15V, VCM = 0V, TA = 25°C, unless otherwise noted.
LT1008M/I
MIN TYP MAX
PARAMETER
CONDITIONS
CMRR
Common Mode Rejection Ratio
VCM = ±13.5V
114
132
114
132
dB
PSRR
Power Supply Rejection Ratio
VS = ±2V to ±20V
114
132
114
132
dB
±13.5 ±14
V
±13.5 ±14
Input Voltage Range
VOUT
IS
MIN
LT1008C
TYP MAX
SYMBOL
UNITS
Output Voltage Swing
RL = 10k
±13
±14
±13
±14
V
Slew Rate
CF = 30pF
0.1
0.2
0.1
0.2
V/μs
Supply Current
(Note 3)
380
600
380
600
μA
The ● indicates specifications which apply over the full operating temperature range of – 55°C ≤ TA ≤ 125°C for the LT1008M, – 40°C
≤ TA ≤ 85°C for the LT1008I and 0°C ≤ TA ≤ 70°C for the LT1008C. VS = ±15V, VCM = 0V, unless otherwise noted.
SYMBOL
PARAMETER
VOS
Input Offset Voltage
(Note 3)
Average Temperature Coefficient of
Input Offset Voltage
IOS
Input Offset Current
(Note 3)
Average Temperature Coefficient of
Input Offset Current
IB
LT1008M/I
MIN TYP MAX
CONDITIONS
Input Bias Current
(Note 3)
Average Temperature Coefficient of
Input Bias Current
MIN
LT1008C
TYP MAX
UNITS
●
●
50
60
250
320
40
50
180
250
μV
μV
●
0.2
1.5
0.2
1.5
μV/°C
●
●
60
80
250
350
40
50
180
250
pA
pA
●
0.4
2.5
0.4
2.5
pA/°C
±80 ±600
±150 ±800
●
●
●
0.6
±40 ±180
±50 ±250
6
0.4
2.5
pA
pA
pA/°C
AVOL
Large-Signal Voltage Gain
VOUT = ±12V, RL ≥ 10k
●
100
1000
150 1500
CMRR
Common Mode Rejection Ratio
VCM = ±13.5V
●
108
128
110
130
dB
Power Supply Rejection Ratio
VS = ±2.5V to ±20V
●
108
126
110
128
dB
●
±13.5
●
±13
PSRR
Input Voltage Range
VOUT
Output Voltage Swing
IS
Supply Current
RL = 10k
●
V/mV
±13.5
±14
400
±13
V
±14
V
800
μA
TYP
MAX
UNITS
30
40
200
250
μV
μV
800
400
(LT1008S8 only) VS = ±15V, VCM = 0V, TA = 25°C, unless otherwise noted.
SYMBOL
PARAMETER
VOS
Input Offset Voltage
CONDITIONS
(Note 3)
Long-Term Input Offset Voltage Stability
IOS
IB
en
MIN
μV/Month
0.3
Input Offset Current
(Note 3)
100
120
280
380
pA
pA
(Note 3)
±100
±120
±300
±400
pA
pA
Input Bias Current
Input Noise Voltage
0.1Hz to 10Hz
0.5
Input Noise Voltage Density
fO = 10Hz (Note 5)
fO = 1000Hz (Note 5)
17
14
μVP-P
30
22
nV/√Hz
nV/√Hz
1008fb
3
LT1008
ELECTRICAL CHARACTERISTICS
(LT1008S8 only) VS = ±15V, VCM = 0V, TA = 25°C, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
in
Input Noise Current Density
fO = 10Hz
AVOL
Large-Signal Voltage Gain
CMRR
PSRR
MIN
TYP
20
fA/√Hz
VOUT = ±12V, RL ≥ 10k
VOUT = ±10V, RL ≥ 2k
200
120
2000
600
V/mV
V/mV
Common Mode Rejection Ratio
VCM = ±13.5V
110
132
dB
Power Supply Rejection Ratio
VS = ±2V to ±20V
Input Voltage Range
VOUT
IS
MAX
UNITS
110
132
dB
±13.5
±14
V
±14
V
Output Voltage Swing
RL = 10k
±13
Slew Rate
CF = 30pF
0.1
Supply Current
(Note 3)
0.2
380
V/μs
600
μA
(LT1008S8 only) The ● indicates specifications which apply over the full operating temperature range of 0°C ≤ TA ≤ 70°C.
VS = ±15V, VCM = 0V, unless otherwise noted.
SYMBOL
PARAMETER
VOS
Input Offset Voltage
CONDITIONS
MIN
(Note 3)
Average Temperature Coefficient of
Input Offset Voltage
IOS
Input Offset Current
(Note 3)
Average Temperature Coefficient of
Input Offset Current
IB
Input Bias Current
(Note 3)
Average Temperature Coefficient of
Input Bias Current
TYP
MAX
UNITS
●
●
40
50
280
340
μV
μV
●
0.2
1.8
μV/°C
●
●
120
140
380
500
pA
pA
●
0.4
4
●
●
±120
±140
±420
±550
●
0.4
5
pA/°C
pA
pA
pA/°C
AVOL
Large-Signal Voltage Gain
VOUT = ±12V, RL ≥ 10k
●
150
1500
V/mV
CMRR
Common Mode Rejection Ratio
VCM = ±13.5V
●
108
130
dB
Power Supply Rejection Ratio
VS = ±2.5V to ±20V
●
108
128
dB
●
±13.5
●
±13
PSRR
Input Voltage Range
VOUT
Output Voltage Swing
IS
Supply Current
RL = 10k
Note 1:Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Differential input voltages greater than 1V will cause excessive
current to flow through the input protection diodes unless current limiting
resistors are used.
●
V
±14
400
V
800
μA
Note 3: These specifications apply for ±2V ≤ VS ≤ ±20V
(±2.5V ≤ VS ≤ ±20V over the temperature range) and
–13.5V ≤ VCM ≤ 13.5V (for VS = ±15V).
Note 4: 10Hz noise voltage density is sample tested on every lot. Devices
100% tested at 10Hz are available on request.
Note 5: This parameter is tested on a sample basis only.
1008fb
4
LT1008
W
FREQUE CY CO PE SATIO CIRCUITS
U
U
U
Standard Compensation Circuit
R1
Alternate* Frequency Compensation
R2
R1
–VIN
R2
–VIN
2
R3
+VIN
3
**BANDWIDTH AND SLEW RATE
ARE PROPORTIONAL TO 1/CF
–
+
6
LT1008
VOUT
8
3
+VIN
R1CO
R1 + R2
CO = 30pF
CF ≥
1
2
*IMPROVES REJECTION OF POWER
SUPPLY NOISE BY A FACTOR OF 5
**BANDWIDTH AND SLEW RATE ARE
PROPORTIONAL TO 1/CS
–
+
6
LT1008
VOUT
8
CS**
100pF
1008 FCC02
CF**
1008 FCC01
FOR
R2
> 200, NO EXTERNAL FREQUENCY COMPENSATION IS NECESSARY
R1
U W
Offset Voltage Drift vs Source
Resistance (Balanced or
Unbalanced)
Offset Voltage vs Source
Resistance (Balanced or
Unbalanced)
10
10
MAXIMUM
1
Input Bias Current vs
Common Mode Range
60
VS = ±15V
TA = 25°C
1
MAXIMUM
0.1
TYPICAL
10k
100k
1M
10M
SOURCE RESISTANCE (Ω)
1k
100M
100k
1M
10M
10k
SOURCE RESISTANCE (Ω)
0
100M
IB
3
2
METAL CAN (H) PACKAGE
1
DUAL-IN-LINE PACKAGE
PLASTIC (N) OR CERDIP (J)
10
–5
0
5
–10
COMMON MODE INPUT VOLTAGE (V)
15
Offset Voltage Drift with
Temperature of Four
Representative Units
60
8
40
6
OFFSET VOLTAGE (μV)
CHANGE IN OFFSET VOLTAGE (μV)
4
VCM
–
+
1008 G03
10
VS = ±15V
TA = 25°C
DEVICE WITH NEGATIVE INPUT CURRENT
–20
Long-Term Stability of Four
Representative Units
Warm-Up Drift
CHANGE IN OFFSET VOLTAGE (μV)
RINCM = 2 × 1012Ω
1008 G02
1008 G01
5
20
–60
–15
0.01
1k
DEVICE WITH POSITIVE INPUT CURRENT
–40
TYPICAL
0.1
VS = ±15V
TA = 25°C
40
INPUT BIAS CURRENT (pA)
100
INPUT OFFSET VOLTAGE (mV)
OFFSET VOLTAGE DRIFT WITH TEMPERATURE (μV/°C)
TYPICAL PERFOR A CE CHARACTERISTICS
4
2
0
–2
–4
–6
20
0
–20
–40
–8
0
0
1
3
4
2
TIME AFTER POWER ON (MINUTES)
5
1008 G04
–10
0
1
3
2
TIME (MONTHS)
4
5
1008 G05
–60
–50
–25
50
25
75
0
TEMPERATURE (°C)
100
125
1008 G06
1008fb
5
LT1008
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Supply Current vs Supply Voltage
Output Short-Circuit Current vs Time
15
500
SHORT-CIRCUIT CURRENT (mA)
SINKING
SOURCING
SUPPLY CURRENT (μA)
12
450
400
25°C
125°C
350
–55°C
–55°C
9
6
125°C
25°C
3
0
–3
125°C
–6
25°C
–9
–55°C
–12
300
–15
10
15
5
SUPPLY VOLTAGE (±V)
0
0
20
2.5 3.0 3.5
0.5 1.0 1.5 2.0
TIME FROM OUTPUT SHORT (MINUTES)
1008 G08
1008 G07
0.1Hz to 10Hz Noise
Noise Spectrum
1000
TA = 25°C
VS = ±2V TO ±20V
TOTAL NOISE DENSITY (μV/√Hz)
NOISE VOLTAGE (400nV/DIV)
VOLTAGE NOISE DENSITY (nV/√Hz)
CURRENT NOISE DENSITY (fA/√Hz)
TA = 25°C
VS = ±2V TO ±20V
Total Noise vs Source Resistance
10
100
CURRENT NOISE
VOLTAGE NOISE
10 1/f CORNER
2.5Hz
1/f CORNER
120Hz
6
4
TIME (SECONDS)
8
10
100
FREQUENCY (Hz)
1
10
1000
Voltage Gain vs Frequency
40
140
30
GAIN (dB)
20
1
10 100 1k 10k 100k 1M 10M
FREQUENCY (Hz)
1008 G12
φ
CS = 10pF
GAIN
CS = 100pF
20
φ
CS = 100pF
140
10
0
0
0.1
AT 1Hz
RESISTOR NOISE ONLY
102
103
104
105
106
107
SOURCE RESISTANCE (Ω)
160
PHASE MARGIN
WITH CS = 100pF = 56°
TA = 25°C
VS = ±15V
–10
0.01
0.1
1
FREQUENCY (MHz)
108
180
200
10
1008 G13
30
20
GAIN
CF = 3pF
100
φ
CF = 30pF
120
φ
CF = 3pF
GAIN
CF = 30pF
140
10
PHASE MARGIN
0 WITH C = 30pF = 60°
F
TA = 25°C
VS = ±15V
–10
0.1
1
0.01
FREQUENCY (MHz)
160
PHASE SHIFT (DEG)
CS = 10pF
CF = 30pF
RS = 2R
40
120
100
–20
0.01 0.1
100
PHASE SHIFT (DEG)
VOLTAGE GAIN (dB)
CF = 3pF
40
–
+
Gain, Phase Shift vs Frequency
with Standard (Feedback)
Compensation
GAIN
CS = 10pF
120
60
R
1008 G11
Gain, Phase Shift vs Frequency
with Alternate Compensation
CS = 100pF
R
1008 G10
1008 G09
80
1
AT 10Hz
GAIN (dB)
2
AT 10Hz
AT 1Hz
0.01
1
0
TA = 25°C
VS = ±2V TO ±20V
180
200
10
1008 G14
1008fb
6
LT1008
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Common Mode Rejection
vs Frequency
10M
140
–55°C
3M
VOLTAGE GAIN
COMMON MODE REJECTION RATIO (dB)
VS = ±15V
VO = ±10V
25°C
1M
125°C
300k
Power Supply Rejection
vs Frequency
VS = ±15V
TA = 25°C
120
CF = 30pF
100
CS = 100pF
80
60
40
20
100k
0
1
10
2
5
LOAD RESISTANCE (kΩ)
1
20
10k
1k
100
FREQUENCY (Hz)
10
100k
1008 G15
VS = ±15V
TA = 25°C
120
NEGATIVE
SUPPLY
100
POSITIVE
SUPPLY
CF = 30pF
80
POSITIVE
SUPPLY
CS = 100pF
60
40
20
0.1
1
10
100 1k
10k
FREQUENCY (Hz)
1008 G16
1M
Large-Signal Transient Response
VS = ±15V
TA = 25°C
2V/DIV
SLEW RATE (V/μs)
10
100k
1008 G17
Slew Rate
vs Compensation Capacitance
Large-Signal Transient Response
2V/DIV
1M
140
POWER SUPPLY REJECTION RATIO (dB)
Voltage Gain vs Load Resistance
1
CS
CF
AV = 1
CS = 100pF
20μs/DIV
AV = 1
CF = 30pF
1008 G18
0.1
0
20
40
60
80
COMPENSATION CAPACITOR (pF)
20μs/DIV
1008 G20
100
108 G19
AV = 1
CS = 100pF
CLOAD = 100pF
5μs/DIV
1008 G21
Small-Signal Transient Response
20mV/DIV
Small-Signal Transient Response
20mV/DIV
20mV/DIV
Small-Signal Transient Response
AV = 1
CS = 100pF
CLOAD = 600pF
5μs/DIV
1008 G22
AV = 1
CF = 30pF
CLOAD = 100pF
5μs/DIV
1008 G23
1008fb
7
LT1008
U
W
U U
APPLICATIO S I FOR ATIO
Achieving Picoampere/Microvolt Performance
In order to realize the picoampere—microvolt level accuracy of the LT1008, proper care must be exercised. For
example, leakage currents in circuitry external to the op
amp can significantly degrade performance. High quality
insulation should be used (e.g., TeflonTM, Kel-F); cleaning
of all insulating surfaces to remove fluxes and other
residues will probably be required. Surface coating may be
necessary to provide a moisture barrier in high humidity
environments.
The LT1008 is specified over a wide range of power supply
voltages from ±2V to ±18V. Operation with lower supplies
is possible down to ±1.2V (two Ni-Cad batteries).
Test Circuit for Offset Voltage and Its Drift with Temperature
50k*
15V
2
100Ω*
3
–
+
*RESISTORS MUST HAVE LOW
THERMOELECTRIC POTENTIAL
7
LT1008
6
VO
4
Board leakage can be minimized by encircling the input
circuitry with a guard ring operated at a potential close to
that of the inputs: in inverting configurations the guard
ring should be tied to ground, in noninverting connections
to the inverting input at Pin 2. Guarding both sides of the
printed circuit board is required. Bulk leakage reduction
depends on the guard ring width. Nanoampere level leakage into the compensation terminals can affect offset
voltage and drift with temperature.
COMPENSATION
V+
7
OUTPUT
1
6
2
4
3
1008 AI02
Noise Testing
The 0.1Hz to 10Hz peak-to-peak noise of the LT1008 is
measured in the test circuit shown. The frequency response of this noise tester indicates that the 0.1Hz corner
is defined by only one zero. The test time to measure 0.1Hz
to 10Hz noise should not exceed 10 seconds, as this time
limit acts as an additional zero to eliminate noise contributions from the frequency band below 0.1Hz.
PU
TS
Current noise is measured in the circuit shown and calculated by the following formula where the noise of the
source resistors is subtracted.
IN
V–
VO = 1000VOS
–15V
A noise voltage density test is recommended when measuring noise on a large number of units. A 10Hz noise
voltage density measurement will correlate well with a
0.1Hz to 10Hz peak-to-peak noise reading since both
results are determined by the white noise and the location
of the 1/f corner frequency.
8
5
50k*
THIS CIRCUIT IS ALSO USED AS
THE BURN-IN CONFIGURATION
FOR THE LT1008 WITH SUPPLY
VOLTAGES INCREASED TO ±20V
GUARD
1008 AI01
REFERENCE ONLY—OBSOLETE PACKAGE
Microvolt level error voltages can also be generated in the
external circuitry. Thermocouple effects caused by temperature gradients across dissimilar metals at the contacts to the input terminals can exceed the inherent drift of
the amplifier. Air currents over device leads should be
minimized, package leads should be short, and the two
input leads should be as close together as possible and
maintained at the same temperature.
1/ 2
⎡e2no – (820nV )2 ⎤
⎢
⎦⎥
in = ⎣
40MΩ × 100
10k
10M* 10M* 2
100Ω
10M* 10M* 3
*METAL FILM
–
LT1008
6
eno
+
1008 AI04
1008fb
8
LT1008
U
W
U U
APPLICATIO S I FOR ATIO
0.1Hz to 10Hz Noise Test Circuit
0.1μF
100k
10Ω
–
2k
+
+
LT1008*
4.7μF
22μF
4.3k
LT1001
VOLTAGE
GAIN: 50,000
110k
2.2μF
–
SCOPE
×1
RIN = 1M
100k
24.3k
Frequency Compensation
The LT1008 is externally frequency compensated with a
single capacitor. The two standard compensation circuits
shown earlier are identical to the LM108A/LM308A frequency compensation schemes. Therefore, the LT1008
operational amplifiers can be inserted directly into
LM108A/LM308A sockets, with similar AC and upgraded
DC performance.
External frequency compensation provides the user with
additional flexibility in shaping the frequency response of
the amplifier. For example, for a voltage gain of ten and
CF = 3pF, a gain bandwidth product of 5MHz and slew rate
of 1.2V/μs can be realized. For closed-loop gains in excess
of 200, no external compensation is necessary, and slew
rate increases to 4V/μs. The LT1008 can also be overcompensated (i.e., CF > 30pF or CS > 100pF) to improve capacitive load handling capability or to narrow noise bandwidth.
In many applications, the feedback loop around the amplifier has gain (e.g., logarithmic amplifiers); overcompensation can stabilize these circuits with a single capacitor.
The availability of the compensation terminals permits the
use of feedforward frequency compensation to enhance
slew rate in low closed-loop gain configurations. The
inverter slew rate is increased to 1.4V/μs. The voltage
follower feedforward scheme bypasses the amplifier’s
gain stages and slews at nearly 10V/μs.
The inputs of the LT1008 are protected with back-to-back
diodes. Current limiting resistors are not used, because the
leakage of these resistors would prevent the realization of
picoampere level bias currents at elevated temperatures.
0.1μF
1008 AI03
In the voltage follower configuration, when the input is
driven by a fast, large-signal pulse (>1V), the input protection diodes effectively short the output to the input during
slewing, and a current, limited only by the output shortcircuit protection, will flow through the diodes.
The use of a feedback resistor, as shown in the voltage
follower feedforward diagram, is recommended because
this resistor keeps the current below the short-circuit
limit, resulting in faster recovery and settling of the output.
Inverter Feedforward Compensation
C2
5pF
R1
10k
INPUT
2
R2
10k
–
6
LT1008
3
1
C1
500pF
VOUT
8
+
R3
3k
C3
10pF
1008 AI05
2V/DIV
*DEVICE UNDER TEST
NOTE: ALL CAPACITOR VALUES ARE FOR
NONPOLARIZED CAPACITORS ONLY
5μs/DIV
1008 AI07
1008fb
9
LT1008
U
W
U U
APPLICATIO S I FOR ATIO
Follower Feedforward Compensation
30pF
10k
10k
INPUT*
–
6
LT1008
3
+
5V/DIV
2
OUTPUT
8
1000pF
1008 AI06
*SOURCE RESISTANCE ≤15k FOR STABILITY
5μs/DIV
1008 AI07
U
TYPICAL APPLICATIO S
Logarithmic Amplifier
Q1A
2N2979
Q1B
2N2979
124k*
5.1k
15V
15V
7
–
8
1
2
LM107
1k
TEL. LABS
TYPE Q81
4
+
100pF
6
15.7k
6
LT1008
3
2k
330pF
+
2
–
10k*
INPUT
LT1004C
1.2V
3
–15V OUTPUT
*1% FILM RESISTOR
30pF
LOW BIAS CURRENT AND OFFSET VOLTAGE OF THE LT1008
ALLOW 4.5 DECADES OF VOLTAGE INPUT LOGGING
Amplifier for Bridge Transducers
R1
100k
R2
100k
3
C1
30pF
R3
510k
R6
56M
1
2
–
8
LT1008
3
+
6
OUTPUT
+
VOLTAGE GAIN ≈ 100
1008 TA04
7
+
2N3609
6
LT1008
2
R4
510k
S2
T
100k
15V
R5
56M
V+
S1
T
100k
Saturated Standard Cell Amplifier
1.018235V
SATURATED
STANDARD
CELL #101
EPPLEY LABS
NEWPORT, R.I.
OUTPUT
4
–
8
1
1000pF
–15V
R2
R1
1008 TA05
THE TYPICAL 30pA BIAS CURRENT OF THE LT1008 WILL
DEGRADE THE STANDARD CELL BY ONLY 1ppm/YEAR.
NOISE IS A FRACTION OF A ppm. UNPROTECTED GATE
MOSFET ISOLATES STANDARD CELL ON POWER DOWN
1008fb
10
LT1008
U
TYPICAL APPLICATIO S
Amplifier for Photodiode Sensor
Five Decade Kelvin-Varley Divider Buffered by the LT1008
R1
5M
1%
2
10V
LT1008
3
100k
KELVIN-VARLEY
DIVIDER
ESI #DP311
00000 – 99999 + 1
–
S1 λ
R2
5M
1%
15V
+
2
8
6
C1
100pF
OUTPUT
7
–
6
LT1008
3
OUTPUT
4
+
8
1
–15V
VOUT = 10V/μA
1000pF
1008 TA06
APPROXIMATE ERROR DUE TO NOISE, BIAS CURRENT,
COMMON MODE REJECTION. VOLTAGE GAIN OF THE
1008 TA07
AMPLIFIER IS 1/5 OF A LEAST SIGNIFICANT BIT
The LT1008 integrator extends low frequency range. Total
dynamic range is 0.01Hz to 10kHz (or 120dB) with 0.01%
linearity.
Extended Range Charge Pump Voltage to Frequency Converter
15V
50k
–15V
15V
OPTIONAL 0.01Hz TRIM
1000pF
(POLYSTYRENE)
1.8k
22M
1μF
2
–
63.4k*
6
10k*
3
+
100pF
100k
750k
10k*
2
–
LT1008
3
+
8
LM301A
1k
6
LM329
22k
10k
7
15V
2
LT1004C
1.2V
LT311A
–
10k*
+
VIN
0V TO 10V
1
3
10k
10k
–15V
15V
4
5pF
–15V
*1% METAL FILM RESISTOR
ALL DIODES 1N4148
1008 TA08
FREQUENCY OUPUT
0.01Hz TO 10kHz
1008fb
11
LT1008
U
TYPICAL APPLICATIO S
Precision, Fast Settling, Lowpass Filter
This circuit is useful where fast signal acquisition and high
precision are required, as in electronic scales.
10k
2
6
LT1008
2k
3
INPUT
1k
+
1
OPTO-MOS*
15V
8
1000pF
+
#1
LT311A
15V
–
4
–15V
The circuit settles to a final value three times as fast as a
simple 1.5M-1μF filter with almost no DC error.
2
3
1
FILTER CUT
IN ADJUST
100Ω
*OPTO-MOS SWITCH
TYPE OFM1A
THETA-J CORP
10k
5
15V
–
8
7
#2
LT311A
+
4
–15V
OUTPUT
8
1μF
7
The filter’s time constant is set by the 2k resistor and the
1μF capacitor until comparator 1 switches. The time
constant is then set by the 1.5M resistor and the 1μF
capacitor. Comparator 2 provides a quick reset.
–
1.5M
3
2
1
1008 TA09
Fast Precision Inverters
2pF TO 8pF
10k*
10k*
INPUT
10k 1N4148 ×2
10k*
2N4393
×2
10k*
INPUT
15V
1
2
300pF
5
–
7 6
LT318A
3
10pF
+
2
15V
2
4
15k
3
10k
1N4148 (4)
–
7
–
6
3
4
+
8
1
7
LT318A
LT1008
–15V
15V
1000pF
OUTPUT
+
6
OUTPUT
4
–15V
–15V
10k
30pF
FULL POWER BANDWIDTH = 2MHz
SLEW RATE AT 50V/μs
SETTLING (10V STEP) = 12μs TO 0.01%
BIAS CURRENT DC = 30pA
OFFSET DRIFT = 0.3μV/°C
OFFSET VOLTAGE = 30μV
*1% METAL FILM
300pF
15V
10k
2
7
–
6
LT1008
3
10k
4
+
8
1
30pF
–15V
SLEW RATE = 100V/μs
SETTLING (10V STEP) = 5μs TO 0.01%
OFFSET VOLTAGE = 30μV
BIAS CURRENT DC = 30pA
*1% METAL FILM
1008 TA10
1008fb
12
LT1008
W
W
SCHE ATIC DIAGRA
COMP1
COMP2
1
8
V+
7
1.3k
Q7
Q20
Q14
22k
22k
4.2k
3k
Q22
Q8
1.5k
Q6
Q5
Q27
Q4
Q24
Q3
S
S
70Ω
Q28
S
Q2
50k
Q15
Q38
Q26
J1
Q31
Q39
3k
1.5k
Q12
Q10
6
Q11 Q23
Q9
+INPUT
60Ω OUTPUT
3k
Q13
Q1
Q37
S
Q16
2
Q43
Q25
Q21
–INPUT
Q30
Q29
Q32
3
Q42
Q33
16k
Q17
Q18
Q35
Q19
Q40
20k
3.3k
Q41
3.3k
Q34
V–
4.3k
4.8k
3.3k
320Ω
40Ω
330Ω
4
1008fb
13
LT1008
U
PACKAGE DESCRIPTIO
H Package
8-Lead TO-5 Metal Can (.200 Inch PCD)
(Reference LTC DWG # 05-08-1320)
0.335 – 0.370
(8.509 – 9.398)
DIA
0.305 – 0.335
(7.747 – 8.509)
0.027 – 0.045
(0.686 – 1.143)
45°TYP
0.040
(1.016)
MAX
0.050
(1.270)
MAX
SEATING
PLANE
0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
0.010 – 0.045*
(0.254 – 1.143)
PIN 1
0.028 – 0.034
(0.711 – 0.864)
0.200
(5.080)
TYP
REFERENCE
PLANE
0.500 – 0.750
(12.700 – 19.050)
H8(TO-5) 0.200 PCD 1197
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
0.016 – 0.021**
(0.406 – 0.533)
*LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
0.016 – 0.024
**FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS
(0.406 – 0.610)
J8 Package
8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
CORNER LEADS OPTION
(4 PLCS)
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.005
(0.127)
MIN
0.405
(10.287)
MAX
8
7
6
5
0.025
(0.635)
RAD TYP
0.220 – 0.310
(5.588 – 7.874)
1
2
0.300 BSC
(0.762 BSC)
3
4
0.200
(5.080)
MAX
0.015 – 0.060
(0.381 – 1.524)
0.008 – 0.018
(0.203 – 0.457)
0° – 15°
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
0.045 – 0.065
(1.143 – 1.651)
0.014 – 0.026
(0.360 – 0.660)
0.100
(2.54)
BSC
0.125
3.175
MIN
J8 1298
OBSOLETE PACKAGES
1008fb
14
LT1008
U
PACKAGE DESCRIPTIO
N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
.255 ± .015*
(6.477 ± 0.381)
.300 – .325
(7.620 – 8.255)
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
(
+.035
.325 –.015
8.255
+0.889
–0.381
.130 ± .005
(3.302 ± 0.127)
.045 – .065
(1.143 – 1.651)
)
.120
.020
(3.048)
MIN
(0.508)
MIN
.018 ± .003
.100
(2.54)
BSC
(0.457 ± 0.076)
N8 1002
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
8
.245
MIN
7
6
5
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
1
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
.053 – .069
(1.346 – 1.752)
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
2
3
4
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
SO8 0303
1008fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT1008
U
TYPICAL APPLICATIO
Ammeter measures currents from 100pA to 100μA without the use of expensive high value resistors. Accuracy at
100μA is limited by the offset voltage between Q1 and Q2
and at 100pA by the inverting bias current of the LT1008.
Ammeter with Six Decade Range
10k
15V
Q3
100μA
METER
R1
2k
1.2k
100pA
Q1
15V
CURRENT
INPUT
10k
2
RANGE 1nA
7
–
Q2
6
LT1008
3
33k
549Ω
4
+
10nA
Q4
8
1
549Ω
–15V PIN 13
CA3146
LT1004C-1.2
549Ω
100nA
549Ω
0.01μF
Q1 TO Q4: RCA CA3146 TRANSISTOR ARRAY
CALIBRATION: ADJUST R1 FOR FULL SCALE
DEFLECTION WITH 1μA INPUT CURRENT
1μA
549Ω
10μA
549Ω
100μA
1008 TA11
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1012
Picoamp Input Current, Microvolt Offset, Low Noise Op Amp
Internally Compensated LT1008
LT1112
Dual Low Power, Precision, Picoamp Input Op Amp
Dual LT1012
LT1880
SOT-23, Rail-to-Rail Output, Picoamp Input Current Precision Op Amp
Single SOT-23 Version of LT1884
LT1881/LT1882
Dual and Quad Rail-to-Rail Output, Picoamp Input Precision Op Amps
Dual/Quad CLOAD Stable
LT1884/LT1885
Dual and Quad Rail-to-Rail Output, Picoamp Input Precision Op Amps
Dual/Quad Faster LT1881/LT1882
1008fb
16
Linear Technology Corporation
LT 0607 REV B • PRINTED IN THE USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 1991
Similar pages