XC6219/6211 Series
ETR0307-005
High Speed LDO Regulators, Low ESR Cap. Compatible, ON/OFF Switch
■GENERAL DESCRIPTION
The XC6219/XC6211 series are highly accurate, low noise, CMOS LDO Voltage Regulators. Offering low output noise, high
ripple rejection ratio, low dropout and very fast turn-on times, the XC6219/6211 series is ideal for today’s cutting edge mobile
phone. Internally the XC6219/6211 includes a reference voltage source, error amplifiers, driver transistors, current limiters
and phase compensators. The XC6219/6211’s current limiters' foldback circuit also operates as a short protect for the output
current limiter and. the output pin. The output voltage is set by laser trimming. Voltages are selectable in 50mV steps within
a range of 0.9V to 5.0V. The XC6219/6211 series is also fully compatible with low ESR ceramic capacitors, reducing cost and
improving output stability. This high level of output stability is maintained even during frequent load fluctuations, due to the
excellent transient response performance and high PSRR achieved across a broad range of frequencies.
The CE function allows the output of regulator to be turned off, resulting in greatly reduced power consumption.
■APPLICATIONS
■FEATURES
●Mobile phones
●Cordless phones, radio communication equipment
●Portable games
●Cameras, Video cameras
●Reference voltage sources
●Battery powered equipment
Maximum Output Current
Dropout Voltage
Operating Voltage Range
Output Voltage Range
Highly Accuracy
Low Power Consumption
Standby Current
High Ripple Rejection
: 150mA (VOUT<1.75V, A~D type)
: 240mA (VOUT>1.8V, A~D type)
: 300mA (VOUT>1.3V, E~H type)
: 200mV @ IOUT=100mA
: 2.0V ~ 6.0V
: 0.9V ~ 5.0V (50mV steps)
: +2% (VOUT>1.5V)
: +30mV (VOUT≦1.5V)
: +1% (VOUT≧3.0V)
: 25μA (TYP.)
: Less than 0.1μA (TYP.)
: 65dB @10kHz
Operating Temperature Range
Low ESR Capacitor
Ultra Small Packages
■TYPICAL APPLICATION CIRCUIT
●XC6219 series
: Ceramic capacitor compatible
: SOT-25 (SOT-23-5)
: SOT-89-5 (for XC6219 only)
: USP-6B (for XC6219 only)
■TYPICAL PERFORMANCE
CHARACTERISTICS
●Ripple Rejection Rate
1
VIN
2
VSS
3
CE
VOUT
5
CL
1µF
NC
4
CIN
1µF
SOT-25 (SOT-23-5)
1/23
XC6219/6211 Series
■PIN CONFIGURATION
[XC6219 Series]
VOUT
NC
5
4
1
2
3
VIN
VSS
CE
VOUT VSS
5
VIN
2
1
NC
2
VSS
4
CE 6
1 VIN
VSS 5
2 NC
3 VOUT
NC 4
3
CE
SOT-25 (SOT-23-5)
SOT-89-5
USP-6B
(TOP VIEW)
(TOP VIEW)
(BOTTOM VIEW)
[XC6211 Series]
VIN
5
VOUT
4
1
2
3
CE
VSS
NC
SOT-25 (SOT-23-5)
(TOP VIEW)
■PIN ASSIGNMENT
XC6211
SOT-25
5
2
1
3
4
PIN NUMBER
XC6219
SOT-25
SOT-89-5
1
4
2
2
3
3
4
1
5
5
USP-6B
1
5
6
2, 4
3
PIN NAME
FUNCTIONS
VIN
VSS
CE
NC
VOUT
Power Input
Ground
ON / OFF Control
No Connection
Output
■FUNCTION
SERIES
A, B, E, F Series
C, D, G, H Series
H=High Level
L=Low Level
2/23
CE
H
L
H
L
OPERATIONAL STATE
ON
OFF
OFF
ON
* The dissipation pad for the USP-6B
package should be solder-plated in
recommended mount pattern and
metal masking so as to enhance
mounting strength and hear release.
XC6219/6211
Series
■PRODUCT CLASSIFICATION
●Selection Guide
The following options for the CE pin logic and internal pull-up/down are available:
High Active + no pull-down resistor built-in (standard)
High Active + 2.0MΩ pull-down resistor built-in <between CE-VSS> (semi-custom)
Low Active + no pull-up resistor built-in (semi-custom)
Low Active + 2.0MΩ pull-up resistor built-in <between VIN-CE> (semi-custom)
Note: *With the pull-up resistor or pull-down resistor built-in types, the supply current during operation will increase
by VIN / 2.0MΩ (TYP.)
●Ordering Information
XC6219/XC6211 ①②③④⑤⑥
DESIGNATOR
①
(*1)
② ③
DESCRIPTION
SYMBOL
CE Pin Logic
A/E
B/F
C/G
D/H
Output Voltage
09～50
P
: SOT-89-5 (for XC6219 only)
D
: USP-6B (for XC6219 only)
R
: Embossed tape, standard feed
L
: Embossed tape, reverse feed
Output Voltage Accuracy
A
B (*2)
⑥
Packages
Device Orientation
: e.g. ②=3, ③=0, → 3.0V
M
1 (*2)
⑤
: High Active, pull-down resistor built in (Semi-custom)
: High Active, no pull-down resistor built in (Standard)
: Low Active, pull-up resistor built in (Semi-custom)
: Low Active, no pull-up resistor built in (Semi-custom)
: 100mV increments, ±2% accuracy
e.g. ③=2, ③=8, ④=2 → 2.80V, ±2%
: 100mV increments, ±1% accuracy
e.g. ②=2, ③=8, ④=1 → 2.80V, ±1%
: 50mV increments, ±2% accuracy
e.g. ②=2, ③=8, ④=A → 2.85V, ±2%
: 50mV increments, ±1% accuracy
e.g. ②=2, ③=8, ④=B → 2.85V, ±1%
: SOT-25 (SOT-23-5)
1/2
④
DESCRIPTION
NOTE：
*1：Maximum output current of XC6219/6211 E to H series is 300mA.
*2：Output voltage of the ±1% accuracy product is 3.0V or more.
3/23
XC6219/6211 Series
■BLOCK DIAGRAM
■ABSOLUTE MAXIMUM RATINGS
Ta=25℃
PARAMETER
SYMBOL
RATINGS
UNITS
Input Voltage
Output Current
Output Voltage
CE Pin Voltage
VIN
IOUT
VOUT
VCE
7.0
500
VSS - 0.3 ~ VIN + 0.3
VSS - 0.3 ~ VIN + 0.3
250
500
100
- 40 ~ + 85
- 55 ~ + 125
V
mA
V
V
SOT-25
SOT-89
USP-6B
Operating Temperature Range
Storage Temperature Range
Power Dissipation
4/23
Pd
Topr
Tstg
mW
℃
℃
XC6219/6211
Series
■ELECTRICAL CHARACTERISTICS
●XC6219/6211 series
Ta=25℃
PARAMETER
SYMBOL
Output Voltage
VOUT(E)
Maximum Output Current
Load Regulation
Line Regulation
IOUTMAX
UVOUT
Vdif1
Vdif2
IDD
Istby
UVOUT
UVIN・VOUT
Input Voltage
VIN
Dropout Voltage
Supply Current
Stand-by Current
CONDITIONS
MIN.
IOUT=30mA (*1, 2, 8)
x 0.98
1% accuracy=VOUT(T)>3.0V
x 0.99
Input conditions (E-1)
1mA≦IOUT≦100mA
IOUT=30mA (*3, 4, 5)
IOUT=100mA (*3, 4, 5)
VCE=VIN
VCE=VSS
VOUT(T) +1.0V≦VIN≦7.0V
IOUT=30mA
Output Voltage
UVOUT
IOUT=30mA
Temperature Characteristics UTopr・VOUT -40℃≦Topr≦85℃
IOUT=50mA,
f=10kHz
Ripple Rejection Rate
PSRR
Current Limiter
Ilim
Short Circuit Current
CE ‘High’ Level Voltage
CE ‘Low’ Level Voltage
Ishort
VCEH
VCEL
CE ‘High’ Level Current
ICEH
VCE=VIN
CE ‘Low’ Level Current
ICEL
VCE=VSS
E-2
-
XC6219/11A, E
XC6219/11B, C, D, F, G, H
XC6219/11D, G
XC6219/11A, B, C, E, F, H
VOUT(T)
MAX.
UNITS CIRCUIT
x 1.02
x 1.01
50
V
①
①
①
-
15
E-3
E-4
25
0.01
50
0.10
mA
mV
mV
mV
μA
μA
-
0.01
0.20
%/V
①
2.0
-
6.0
V
-
-
100
-
ppm/℃
①
-
65
-
dB
④
mA
①
mA
V
V
①
①
②
μA
②
μA
②
VOUT(E)>1.8V
XC6219/6211A~D type (*7)
XC6219/6211 E~H type (*7)
TYP.
70
1.60
-
300
380
50
-
-0.10
-
-5.0
-0.10
-
VIN
0.25
5.0
0.10
0.10
①
②
②
NOTE: * 1: VOUT(T) = Specified output voltage
* 2: VOUT(E) = Effective output voltage
(I.e. the output voltage when "VOUT(T)+1.0V" is provided at the VIN pin while maintaining a certain IOUT value.)
* 3: Vdif={VIN1(*5)-VOUT1(*4) }
* 4: VOUT1=A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VOUT(T)+1.0V} is input.
* 5: VIN1=The Input Voltage when VOUT1 appears as Input Voltage is gradually decreased.
* 6: Unless otherwise stated, VIN=VOUT(T)+1.0V.
* 7: Input conditions of current limit when 0.9V<VOUT(T)<1.75V is VIN=VOUT(T)+2.0V
* 8: The rated value when VOUT(T)<1.5V is VOUT(T)+30mV
5/23
XC6219/6211 Series
■ELECTRICAL CHARACTERISTICS (Continued)
●Maximum Output Current, Input Voltage Chart
XC6219/6211A~D series
SYMBOL
E-1
CONDITION, RATINGS
E-2
MAX. OUTPUT
CURRENT (mA)
IOUTMAX (MIN.)
150
240
INPUT VOLTAGE (V)
VIN
VOUT(T)+2.0V
VOUT(T)+1.0V
SETTING VOLTAGE (V)
VOUT(T)<1.75V
VOUT(T)>1.8V
XC6219/6211E~H series
SYMBOL
E-1
CONDITION, RATINGS
E-2
MAX. OUTPUT
CURRENT (mA)
IOUTMAX (MIN.)
260
270
290
INPUT VOLTAGE (V)
VIN
2.5
2.6
2.7
2.8
2.9
3.0
VOUT(T)+1.0V
SETTING VOLTAGE (V)
0.90 ~ 1.05
1.10 ~ 1.15
1.20 ~ 1.25
1.30 ~ 1.35
1.40 ~ 1.45
1.50 ~ 1.95
2.00 ~ 6.00
300
●Dropout Voltage Chart
E-3
Vdif1
SYMBOL
E-4
Vdif2
PARAMETER
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
1100
500
200
100
-
1100
500
200
120
80
80
80
70
70
60
60
60
50
1110
510
210
150
120
120
120
100
100
90
90
80
70
1100
500
200
100
-
1150
550
300
280
240
240
240
220
220
200
200
180
160
1200
600
400
380
350
330
310
290
270
270
250
230
210
OUTPUT VOLTAGE
0.9
1.50
1.80 ~ 1.85
1.90 ~ 1.95
2.00 ~ 2.05
2.10 ~ 2.25
2.30 ~ 2.45
2.50 ~ 2.75
2.80 ~ 2.95
3.00 ~ 3.05
3.10 ~ 3.95
4.00 ~ 4.95
5.00
* The input voltage 2.0V (MIN.) is needed to operate the IC series.
When the output voltage is less than 2.0V, 2.0V-VOUT(T) of dropout voltage is needed at minimum.
6/23
XC6219/6211
Series
■TEST CIRCUITS
Circuit ①
VIN
CIN=1.0μF
(ceramic)
CE
V
A
VOUT
CL=1.0 μF
(ceramic)
VSS
RL
V
V
Circuit ②
A
VIN
A
CE
VO UT
OPEN
VSS
Circuit ③
VIN
CIN=1.0µF
(ceramic)
CE
VO UT
CL=1.0µF
(ceramic)
F.F.T
VSS
IOUT=10mA
Circuit ④
VIN
V
CE
VOUT
IOUT=50mA
CL=1.0µF
(ceramic)
VSS
V
VIN={VO UT+1}V DC
+0.5V p-pAC
7/23
XC6219/6211 Series
■OPERATIONAL EXPLANATION
<Output Voltage Control>
The voltage divided by resistors R1 & R2 is compared with the internal reference voltage by the error amplifier. The
P-channel MOSFET, which is connected to the VOUT pin, is then driven by the subsequent output signal. The output
voltage at the VOUT pin is controlled and stabilized by a system of negative feedback. The current limit circuit and short
protect circuit operate in relation to the level of output current. Further, the IC's internal circuitry can be shutdown via the
CE pin's signal
<Low ESR Capacitors>
With the XC6209/6212 series, a stable output voltage is achievable even if used with low ESR capacitors as a phase
compensation circuit is built-in. In order to ensure the effectiveness of the phase compensation, we suggest that an output
capacitor (CL) is connected as close as possible to the output pin (VOUT) and the VSS pin. Please use an output capacitor
with a capacitance value of at least 1μF. Also, please connect an input capacitor (CIN) of 0.1μF between the VIN pin and the
VSS pin in order to ensure a stable power input.
Stable phase compensation may not be ensured if the capacitor runs out capacitance when depending on bias and
temperature. In case the capacitor depends on the bias and temperature, please make sure the capacitor can ensure the
actual capacitance.
<Current Limiter, Short-Circuit Protection>
The XC6219/6211 series includes a combination of a fixed current limiter circuit & a foldback circuit, which aid the operations
of the current limiter and circuit protection. When the load current reaches the current limit level, the fixed current limiter
circuit operates and output voltage drops. As a result of this drop in output voltage, the foldback circuit operates, output
voltage drops further and output current decreases. When the output pin is shorted, a current of about 50mA flows.
<CE Pin>
The IC's internal circuitry can be shutdown via the signal from the CE pin with the XC6219/6211 series. In shutdown mode,
output at the VOUT pin will be pulled down to the VSS level via R1 & R2. The operational logic of the IC's CE pin is selectable
(please refer to the selection guide). Note that as the standard XC6219/6211B type's regulator 1 and 2 are both ' High
Active/No Pull-Down', operations will become unstable with the CE pin open. Although the CE pin is equal to an inverter input
with CMOS hysteresis, with either the pull-up or pull-down options, the CE pin input current will increase when the IC is in
operation. We suggest that you use this IC with either a VIN voltage or a VSS voltage input at the CE pin. If this IC is used with
the correct specifications for the CE pin, the operational logic is fixed and the IC will operate normally. However, supply
current may increase as a result of through current in the IC's internal circuitry.
■NOTES ON USE
1. Please use this IC within the stated absolute maximum ratings. The IC is liable to malfunction should the ratings be
exceeded.
2. Where wiring impedance is high, operations may become unstable due to noise and/or phase lag depending on output
current. Please keep the resistance low between VIN and VSS wiring in particular.
3. Please wire the input capacitor (CIN) and the output capacitor (CL) as close to the IC as possible.
8/23
XC6219/6211
Series
■TYPICAL PERFORMANCE CHARACTERISTICS
(1) Output Voltage vs. Output Current
XC6219/11B182
XC6219/11B182
Topr=85℃
25℃
-40℃
XC6219/11B182
XC6219/11B252
Topr=85℃
25℃
-40℃
XC6219/11B302
XC6219/11B302
Topr=85℃
25℃
-40℃
9/23
XC6219/6211 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(2) Output Voltage vs. Input Voltage
XC6219/11x182
XC6219/11x182
XC6219/11x252
XC6219/11x252
XC6219/11x302
10/23
XC6219/11x302
XC6219/6211
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(3) Dropout Voltage vs. Output Current
XC6219/11x252
XC6219/11x182
XC6219/11x302
(4) Supply Current vs. Input Voltage
XC6219/11x182
XC6219/11x252
Topr=85℃
Topr=85℃
25℃
25℃
-40℃
-40℃
11/23
XC6219/6211 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(4) Supply Current vs. Input Voltage (Continued)
XC6219/11x302
Topr=85℃
25℃
-40℃
(5) Output Voltage vs. Ambient Temperature
XC6219/11x182
XC6219/11x302
12/23
XC6219/11x252
XC6219/6211
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(6) Supply Current vs. Ambient Temperature
XC6219/11x182
XC6219/11x252
XC6219/11x302
13/23
XC6219/6211 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(7) Input Transient Response
XC6219/11x182
XC6219/11x182
XC6219/11x252
XC6219/11x252
14/23
XC6219/11x182
XC6219/11x252
XC6219/11x252
XC6219/11x252
XC6219/11x252
XC6219/6211
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(7) Input Transient Response (Continued)
XC6219/11x302
XC6219/11x302
XC6219/11x302
(8) Load Transient Response
XC6219/11x182
XC6219/11x182
15/23
XC6219/6211 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) Load Transient Response (Continued)
XC6219/11x182
VIN=2.8V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
XC6219/11x252
VIN=3.5V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
XC6219/11x302
VIN=4.0V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
16/23
XC6219/11x252
VIN=3.5V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
XC6219/11x252
VIN=3.5V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
XC6219/11x302
VIN=4.0V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
XC6219/6211
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) Load Transient Response (Continued)
XC6219/11x302
VIN=4.0V, trr=tf=5use
CL=1μF (ceramic), CL=1uF (ceramic)
(9) Ripple Rejection Rate
XC6219/11x252
VIN=2.8V, DC+1Vp-pAC
IOUT=50mA, CL=1uF (ceramic)
XC6219/11x252
VIN=2.8V, DC+1Vp-pAC
IOUT=50mA, CL=1uF (ceramic)
XC6219/11x302
VIN=2.8V, DC+1Vp-pAC
IOUT=50mA, CL=1uF (ceramic)
17/23
XC6219/6211 Series
■PACKAGING INFORMATION
●SOT-25 (SOT-23-5)
●SOT-89-5
●USP-6B
2.0±0.15
(0.45) 0.5±0.1
3
(0.27)
5
4
45 ﾟ
45 ﾟ
2
A’
(0.27)
6
(0.27)
1
AAA
AAA
1.8±0.15
A
(φ0.45)
(0.05)
45 ﾟ
0.05+0.01
- 0.005
45 ﾟ
0.005±0.002
（0.125 ）
0.65+0.15
- 0.05
(0.45) (0.45)
5
1
6
0.5±0.1
4
2
0.5±0.1
3
1.6±0.1
A-A' cross section
0.1±0.03
0.2±0.05
5-0.2±0.05
0.7±0.03
1.0±0.1
0.25±0.1
18/23
0.25±0.1
Note : Pin 1 is larger than the other pins.
XC6219/6211
Series
■ RECOMMENDED MOUNT PATTERN
●USP-6B
■ RECOMMENDED METAL MASK DESIGN
●USP-6B
19/23
XC6219/6211 Series
■MARKING RULE
[XC6219 Series]
●SOT-25 (SOT-23-5), SOT-89-5
5
①
1
①Represents product series
4
②
MARK
PRODUCT SERIES
L
XC6219xxxxxx
③ ④
2
②Represents type of regulator
3
MARK
SOT-25
(TOP VIEW)
VOUT 100mV INCREMENTS
VOUT:0.1~3.0V
④
③
4
②
2
①
5
PRODUCT SERIES
VOUT 50mV INCREMENTS
VOUT:3.1~6.0V
VOUT:0.15~3.05V
VOUT:3.15~6.05V
V
A
E
L
X
B
F
M
Y
C
H
N
Z
D
K
P
XC6219Axxxxx
XC6219Bxxxxx
XC6219Cxxxxx
XC6219Dxxxxx
③Represents output voltage
1
2
SOT-89-5
(TOP VIEW)
3
MARK
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
OUTPUT VOLTAGE (V)
0.9
1.0
1.1
1.2
1.3
1.4
1.5
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
0.95
1.05
1.15
1.25
1.35
1.45
1.55
3.15
3.25
3.35
3.45
3.55
3.65
3.75
3.85
3.95
4.05
4.15
4.25
4.35
4.45
4.55
MARK
F
H
K
L
M
N
P
R
S
T
U
V
X
Y
Z
OUTPUT VOLTAGE (V)
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
4.6
4.7
4.8
4.9
5.0
-
1.65
1.75
1.85
1.95
2.05
2.15
2.25
2.35
2.45
2.55
2.65
2.75
2.85
2.95
3.05
④Represents production lot number
0 to 9, A to Z reverse character of 0 to 9, A to Z repeated (G, I, J, O, Q, W excepted)
20/23
4.65
4.75
4.85
4.95
-
XC6219/6211
Series
■MARKING RULE (Continued)
●USP-6B
①②Represents product series
MARK
①
②
1
9
PRODUCT SERIES
XC6219xxxxDx
③Represents type of regulator
USP-6B
(TOP VIEW)
MARK
TYPE
PRODUCT SERIES
A
B
C
D
High Active, pull-down resistor built-in (semi-custom)
High Active, no pull-down resistor built-in (semi-custom)
Low Active, pull-up resistor built-in (semi-custom)
Low Active, no pull-up resistor built-in (semi-custom)
XC6219AxxxMx
XC6219BxxxMx
XC6219CxxxMx
XC6219DxxxMx
④Represents product series
MARK
VOLTAGE (V)
PRODUCT SERIES
3
5
3.X
5.X
XC6219x3xxDx
XC6219x5xxDx
PRODUCT SERIES SYMBOL
VOLTAGE PRODUCT SERIES
⑤Represents output voltage
MARK
VOLTAGE
0
1
2
3
4
5
6
7
8
9
X.0
X.1
X.2
X.3
X.4
X.5
X.6
X.7
X.8
X.9
XC6219xx0xDx
XC6219xx1xDx
XC6219xx2xDx
XC6219xx3xDx
XC6219xx4xDx
XC6219xx5xDx
XC6219xx6xDx
XC6219xx7xDx
XC6219xx8xDx
XC6219xx9xDx
A
B
C
D
E
F
H
K
L
M
X.05
X.15
X.25
X.35
X.45
X.55
X.65
X.75
X.85
X.95
XC6219xx0ADx
XC6219xx1ADx
XC6219xx2ADx
XC6219xx3ADx
XC6219xx4ADx
XC6219xx5ADx
XC6219xx6ADx
XC6219xx7ADx
XC6219xx8ADx
XC6219xx9ADx
⑥Represents production lot number
0 to 9, A to Z repeated (G, I, J, O, Q, W excepted)
* No character inversion used.
21/23
XC6219/6211 Series
■MARKING RULE (Continued)
[XC6211 Series]
●SOT-25(SOT-23-5)
5
①
1
4
②
①Represents product series
③ ④
2
3
MARK
PRODUCT SERIES
A
XC6211xxxxMx
②Represents type of regulator
MARK
VOUT 100mV INCREMENTS
PRODUCT SERIES
VOUT 50mV INCREMENTS
VOUT:0.1~3.0V
VOUT:3.1~6.0V
VOUT:0.15~3.05V
VOUT:3.15~6.05V
V
X
Y
Z
A
B
C
D
E
F
H
K
L
M
N
P
XC6211AxxxMx
XC6211BxxxMx
XC6211CxxxMx
XC6211DxxxMx
③Represents output voltage
MARK
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
OUTPUT VOLTAGE (V)
-
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
-
3.15
3.25
3.35
3.45
3.55
3.65
3.75
3.85
3.95
4.05
4.15
4.25
4.35
4.45
4.55
MARK
F
H
K
L
M
N
P
R
S
T
U
V
X
Y
Z
OUTPUT VOLTAGE (V)
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
4.6
4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
1.65
1.75
1.85
1.95
2.05
2.15
2.25
2.35
2.45
2.55
2.65
2.75
2.85
2.95
3.05
④Represents production lot number
0 to 9, A to Z reverse character of 0 to 9, A to Z repeated (G, I, J, O, Q, W excepted)
22/23
4.65
4.75
4.85
4.95
5.05
5.15
5.25
5.35
5.45
5.55
5.65
5.75
5.85
5.95
6.05
XC6219/6211
Series
1. The products and product specifications contained herein are subject to change without
notice to improve performance characteristics.
Consult us, or our representatives
before use, to confirm that the information in this catalog is up to date.
2. We assume no responsibility for any infringement of patents, patent rights, or other
rights arising from the use of any information and circuitry in this catalog.
3. Please ensure suitable shipping controls (including fail-safe designs and aging
protection) are in force for equipment employing products listed in this catalog.
4. The products in this catalog are not developed, designed, or approved for use with such
equipment whose failure of malfunction can be reasonably expected to directly
endanger the life of, or cause significant injury to, the user.
(e.g. Atomic energy; aerospace; transport; combustion and associated safety
equipment thereof.)
5. Please use the products listed in this catalog within the specified ranges.
Should you wish to use the products under conditions exceeding the specifications,
please consult us or our representatives.
6. We assume no responsibility for damage or loss due to abnormal use.
7. All rights reserved. No part of this catalog may be copied or reproduced without the
prior permission of Torex Semiconductor Ltd.
23/23