ATMEL ATMEGA88-15MT2 8-bit microcontroller with 8k bytes in-system programmable flash Datasheet

Appendix A - ATmega88/168 Automotive specification at
150°C
This document contains information specific to devices operating at temperatures up
to 150°C. Only deviations are covered in this appendix, all other information can be
found in the complete Automotive datasheet. The complete Automotive datasheet can
be found on www.atmel.com
8-bit
Microcontroller
with 8K Bytes
In-System
Programmable
Flash
ATmega88/168
Automotive
Appendix A
PRELIMINARY
Electrical Characteristics
Absolute Maximum Ratings*
Operating Temperature.................................. -55°C to +150°C
*NOTICE:
Storage Temperature ..................................... -65°C to +175°C
Voltage on any Pin except RESET
with respect to Ground ................................-0.5V to VCC+0.5V
Voltage on RESET with respect to Ground......-0.5V to +13.0V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Maximum Operating Voltage ............................................ 6.0V
DC Current per I/O Pin ............................................... 30.0 mA
DC Current VCC and GND Pins................................ 200.0 mA
DC Characteristics
TA = -40°C to 150°C, VCC = 2.7V to 5.5V (unless otherwise noted)
Symbol
Parameter
Condition
Min.
VIL
Input Low Voltage, except
XTAL1 and RESET pin
VCC = 2.7V - 5.5V
VIH
Input High Voltage, except
XTAL1 and RESET pins
VIL1
Max.
Units
-0.5
0.3VCC(1)
V
VCC = 2.7V - 5.5V
0.6VCC(2)
VCC + 0.5
V
Input Low Voltage,
XTAL1 pin
VCC = 2.7V - 5.5V
-0.5
0.1VCC(1)
V
VIH1
Input High Voltage,
XTAL1 pin
VCC = 2.7V - 5.5V
0.7VCC(2)
VCC + 0.5
V
VIL2
Input Low Voltage,
RESET pin
VCC = 2.7V - 5.5V
-0.5
0.2VCC(1)
V
VIH2
Input High Voltage,
RESET pin
VCC = 2.7V - 5.5V
0.9VCC(2)
VCC + 0.5
V
VIL3
Input Low Voltage,
RESET pin as I/O
VCC = 2.7V - 5.5V
-0.5
0.3VCC(1)
V
VIH3
Input High Voltage,
RESET pin as I/O
VCC = 2.7V - 5.5V
0.6VCC(2)
VCC + 0.5
V
VOL
Output Low Voltage(3),
I/O pin except RESET
IOL = 20mA, VCC = 5V
IOL = 5mA, VCC = 3V
0.8
0.5
V
VOH
Output High Voltage(4),
I/O pin except RESET
IOH = -20mA, VCC = 5V
IOH = -10mA, VCC = 3V
IIL
Input Leakage
Current I/O Pin
VCC = 5.5V, pin low
(absolute value)
1
µA
IIH
Input Leakage
Current I/O Pin
VCC = 5.5V, pin high
(absolute value)
1
µA
RRST
Reset Pull-up Resistor
30
60
kΩ
RPU
I/O Pin Pull-up Resistor
20
50
kΩ
2
Typ.
4.0
2.2
V
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
TA = -40°C to 150°C, VCC = 2.7V to 5.5V (unless otherwise noted) (Continued)
Symbol
Parameter
Condition
ICC
Power Supply Current(6)
ICC IDLE
ICC PWD
Power-down mode
Max.
Units
Active 4MHz, VCC = 3V
Active 8MHz, VCC = 5V
8
16
mA
Active 16MHz, VCC = 5V
25
mA
Idle 4MHz, VCC = 3V
Idle 8MHz, VCC = 5V
6
12
mA
Idle 16MHz, VCC = 5V
14
mA
WDT enabled, VCC = 3V
WDT enabled, VCC = 5V
90
140
µA
WDT disabled, VCC = 3V
WDT disabled, VCC = 5V
80
120
µA
40
mV
50
nA
VACIO
Analog Comparator
Input Offset Voltage
VCC = 5V
Vin = VCC/2
IACLK
Analog Comparator
Input Leakage Current
VCC = 5V
Vin = VCC/2
tACPD
Analog Comparator
Propagation Delay
VCC = 4.0V
Min.
Typ.
<10
-50
500
ns
Memory Endurance
EEPROM endurance: 50,000 Write/Erase cycles.
Flash endurance: 10,000 Write/Erase cycles.
Maximum Speed vs. VCC
Maximum frequency is dependent on VCC. As shown in Figure 131, the Maximum Frequency vs.
VCC curve is linear between 2.7V < VCC < 4.5V.
Figure 1. Maximum Frequency vs. VCC
16 MHz
8 MHz
Safe Operating Area
2.7V
4.5V
5.5V
3
7607F–AVR–03/08
ADC Characteristics(6)
TA = -40°C to 150°C, VCC = 4.5V to 5.5V (unless otherwise noted)
Symbol
Parameter
Condition
Min
Resolution
Absolute accuracy
(Including INL, DNL,
quantization error, gain
and offset error)
Max
10
Units
Bits
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
2
3.5
LSB
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
Noise Reduction Mode
2
3.5
LSB
Integral Non-Linearity
(INL)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
0.6
2.5
LSB
Differential Non-Linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
0.30
1.0
LSB
Gain Error
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
-1.3
3.5
LSB
Offset Error
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
1.8
3.5
LSB
Conversion Time
Free Running
Conversion
Clock Frequency
AVCC
Analog Supply Voltage
VREF
Reference Voltage
VIN
Typ
Input Voltage
-3.5
13 cycles
µs
50
200
kHz
VCC - 0.3
VCC + 0.3
V
1.0
AVCC
V
GND
VREF
V
Input Bandwidth
38.5
kHz
VINT
Internal Voltage
Reference
1.0
1.1
1.2
V
RREF
Reference Input
Resistance
25.6
32
38.4
kΩ
RAIN
Analog Input Resistance
Notes:
100
MΩ
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports C0 - C5, should not exceed 200 mA.
3] The sum of all IOL, for ports C6, D0 - D4, should not exceed 300 mA.
4] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 300 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at Vcc = 5V) under steady state conditions (nontransient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports C0 - C5, should not exceed 200 mA.
3] The sum of all IOH, for ports C6, D0 - D4, should not exceed 300 mA.
4] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 300 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
4
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
5. Minimum VCC for Power-down is 2.5V.
ATmega88/168 Typical Characteristics
Active Supply
Current
Figure 2. Active Supply Current vs. Frequency (1 - 20 MHz)
ACTIVE S UP P LY CURRENT vs . FREQUENCY
Te mp = 150c
16
5.5 V
14
5.0 V
12
ICC (mA)
10
8
3.3 V
3.0 V
6
4
2
0
0
2
4
6
8
10
12
14
16
18
20
Fre que nc y (MHz )
Figure 3. Idle Supply Current vs. Frequency (1 - 20 MHz)
IDLE S UP P LY CURRENT vs . FREQUENCY
Te mp = 150˚c
8
ICC (mA)
6
4
5.5 V
5.0 V
3.3 V
3.0 V
2
0
4
6
8
10
12
14
16
18
20
Fre que nc y (MHz )
5
7607F–AVR–03/08
Power-Down Supply
Current
Figure 4. Power-Down Supply Current vs. VCC (Watchdog Timer Disabled)
P OWER-DOWN S UP P LY CURRENT vs . Vcc
WATCHDOG TIMER DISABLED
30
150 ˚C
25
ICC (uA)
20
15
10
125 ˚C
5
85 ˚C
25 ˚C
-40 ˚C
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 5. Power-Down Supply Current vs. VCC (Watchdog Timer Enabled)
P OWER-DOWN S UP P LY CURRENT vs . Vcc
WATCHDOG TIMER ENABLED
35
150 ˚C
30
ICC (uA)
25
20
15
125 ˚C
10
-40 ˚C
85 ˚C
25 ˚C
5
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
6
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Pin Pull-up
Figure 6. I/O Pin Pull-up Resistor Current vs. Input Voltage (VCC = 5V)
I/O P IN P ULL-UP RES IS TOR CURRENT vs . INP UT VOLTAGE
160
150 ˚C
140
120
-40 ˚C
IOP (uA)
100
80
60
40
20
0
0
1
2
3
4
5
6
V OP (V)
Figure 7. Output Low Voltage vs. Output Low Current (VCC = 5V)
I/O P IN OUTP UT VOLTAGE vs . S INK CURRENT
Vc c = 5.00v
0.8
0.7
150 ˚C
125 ˚C
0.6
85 ˚C
Vol (V)
0.5
25 ˚C
0.4
-40 ˚C
0.3
0.2
0.1
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
7
7607F–AVR–03/08
Figure 8. Output Low Voltage vs. Output Low Current (VCC = 3V)
I/O P IN OUTP UT VOLTAGE vs . S INK CURRENT
Vc c = 3.0v
1.4
1.2
150 ˚C
125 ˚C
Vol (V)
1
85 ˚C
0.8
25 ˚C
0.6
-40 ˚C
0.4
0.2
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
Figure 9. Output High Voltage vs. Output High Current (VCC = 5V)
I/O P IN OUTP UT VOLTAGE vs . S OURCE CURRENT
Vc c = 5.00v
5.2
5
Voh (V)
4.8
4.6
-40 ˚C
25 ˚C
85 ˚C
125 ˚C
150 ˚C
4.4
4.2
4
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
8
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Figure 10. Output High Voltage vs. Output High Current (VCC = 3V)
I/O P IN OUTP UT VOLTAGE vs . S OURCE CURRENT
Vc c = 3.0v
3.5
3
Current (V)
2.5
-40 ˚C
25 ˚C
85 ˚C
125 ˚C
150 ˚C
2
1.5
1
0.5
0
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
Figure 11. Reset Pull-Up Resistor Current vs. Reset Pin Voltage (VCC = 5V)
RES ET P ULL-UP RES IS TOR CURRENT vs . RES ET P IN VOLTAGE
140
120
150 ˚C
IRES ET (uA)
100
80
-40 ˚C
60
40
20
0
0
1
2
3
4
5
6
V RE S E T (V)
9
7607F–AVR–03/08
Pin Thresholds and
Hysteresis
Figure 12. I/O Pin Input Threshold vs. VCC (VIH, I/O Pin Read as ‘1’)
IO INP UT THRES HOLD VOLTAGE vs . VC C
VIH, IO PIN READ AS '1'
150 ˚C
-40 ˚C
3
2.5
Vih (V)
2
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 13. I/O Pin Input Threshold vs. VCC (VIL, I/O Pin Read as ‘0’)
IO INP UT THRES HOLD VOLTAGE vs . V
CC
VIL, IO PIN READ AS '0'
3
150 ˚C
2.5
-40 ˚C
Vil (V)
2
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
10
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Figure 14. Reset Input Threshold Voltage vs. VCC (VIH, Reset Pin Read as ‘1’)
RES ET INP UT THRES HOLD VOLTAGE vs . VC C
VIH, IO PIN READ AS '1'
3
2.5
Thres hold (V)
2
-40 ˚C
1.5
150 ˚C
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 15. Reset Input Threshold Voltage vs. VCC (VIL, Reset Pin Read as ‘0’)
RES ET INP UT THRES HOLD VOLTAGE vs . VC C
VIL, IO PIN READ AS '0'
2.5
Thres hold (V)
2
1.5
150 ˚C
1
-40 ˚C
0.5
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
11
7607F–AVR–03/08
Internal Oscillator
Speed
Figure 16. Watchdog Oscillator Frequency vs. VCC
WATCHDOG OS CILLATOR FREQUENCY vs . TEMP ERATURE
Vcc from 2.7V to 5.5V
190
170
FRC (kHz)
150
2.7
3.0
5.0
5.5
130
V
V
V
V
110
90
70
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150 160
Te mpe ra ture
Figure 17. Calibrated 8 MHz RC Oscillator Frequency vs. Temperature
CALIBRATED 8MHz RC OS CILLATOR FREQUENCY vs . TEMP ERATURE
8.4
5.5 V
5.0 V
4.5 V
3.3 V
3.0 V
2.7 V
8.3
8.2
FRC (MHz)
8.1
8
7.9
7.8
7.7
7.6
-40
-30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
12
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Figure 18. Calibrated 8 MHz RC Oscillator Frequency vs. VCC
CALIBRATED 8MHz RC OS CILLATOR FREQUENCY vs . OP ERATING VOLTAGE
FRC (MHz)
8.4
150
8.3
125
8.2
85
8.1
25
8
-40
7.9
7.8
7.7
7.6
2
2.5
3
3.5
4
4.5
5
5.5
6
V CC (V)
Figure 19. Calibrated 8 MHz RC Oscillator Frequency vs. OSCCAL Value
CALIBRATED 8MHz RC OS CILLATOR FREQUENCY vs . OS CCAL VALUE
Vc c = 5.00v
16
150 ˚C
14
-40 ˚C
12
FRC (MHz)
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
BOD Thresholds and
Analog Comparator
Offset
Figure 20. BOD Threshold vs. Temperature (BODLEVEL is 4.0V)
BOD THRES HOLDS vs . TEMP ERATURE
BOD s e tting = 4.30v
4.6
4.5
Thres hold (V)
4.4
1
4.3
0
4.2
4.1
4
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150 160
Te mpe ra ture (C)
13
7607F–AVR–03/08
Figure 21. BOD Threshold vs. Temperature (BODLEVEL is 2.7V)
BOD THRES HOLDS vs . TEMP ERATURE
BOD s e tting = 2.70v
3
2.9
Thres hold (V)
2.8
1
2.7
0
2.6
2.5
2.4
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150 160
Te mpe ra ture (C)
Figure 22. Bandgap Voltage vs. VCC
BANDGAP VOLTAGE vs . VC C
1.25
Bandgap Voltage (V)
1.2
1.15
1.1
150 ˚C
-40 ˚C
1.05
1
0.95
2
2.5
3
3.5
4
4.5
5
5.5
Vc c (V)
14
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Peripheral Units
Figure 23. Analog to Digital Converter GAIN vs. VCC
Gain vs. Temperature
0.00
Error (LSB)
-0.50
-1.00
4 IDL
-1.50
4 STD
-2.00
-2.50
-50
-25
0
25
50
75
100
125
150
Temperature
Figure 24. Analog to Digital Converter OFFSET vs. VCC
Offset vs. Temperature
2.50
2.00
4 IDL
Error (LSB)
4 STD
1.50
1.00
0.50
0.00
-50
-25
0
25
50
75
100
125
150
Temperature
Figure 25. Analog to Digital Converter DNL vs. VCC
DNL vs. Temperature
1.00
0.90
0.80
Error (LSB)
0.70
0.60
0.50
0.40
4 IDL
0.30
4 STD
0.20
0.10
0.00
-50
-25
0
25
50
75
100
125
150
Temperature
15
7607F–AVR–03/08
Figure 26. Analog to Digital Converter INL vs. VCC
INL vs. Temperature
1.00
0.90
0.80
Error (LSB)
0.70
0.60
4 IDL
0.50
4 STD
0.40
0.30
0.20
0.10
0.00
-50
-25
0
25
50
75
100
125
150
Temperature
16
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Grade 0 Qualification
The ATmega88/168 has been developed and manufactured according to the most stringent
quality assurance requirements of ISO-TS-16949 and verified during product qualification as per
AEC-Q100 grade 0.
AEC-Q100 qualification relies on temperature accelerated stress testing. High temperature field
usage however may result in less significant stress test acceleration. In order to prevent the risk
that ATmega88/168 lifetime would not satisfy the application end-of-life reliability requirements,
Atmel has extended the testing, whenever applicable (High Temperature Operating Life Test,
High Temperature Storage Life, Data Retention, Thermal Cycles), far beyond the AEC-Q100
requirements. Thereby, Atmel verified the ATmega88/168 has a long safe lifetime period after
the grade 0 qualification acceptance limits.
The valid domain calculation depends on the activation energy of the potential failure mechanism that is considered. Examples are given in figure 1. Therefore any temperature mission
profile which could exceed the AEC-Q100 equivalence domain shall be submitted to Atmel for a
thorough reliability analysis
AEC-Q100 Lifetime Equivalence
1000000
100000
Hours
10000
1000
100
10
1
0
20
40
60
80
100
120
140
160
Temperature (°C)
HTOL 0,59eV
HTSL 0,45eV
17
7607F–AVR–03/08
Ordering
Information
ATmega88/168
Operation Range
Power Supply
16(2)
2.7 - 5.5V
ATmega88-15MT2
PN
Extended
(-40°C to 150°C)
16(2)
2.7 - 5.5V
ATmega88-15AD
MA
Extended
(-40°C to 150°C)
16(2)
2.7 - 5.5V
ATmega168-15MD
PN
Extended
(-40°C to 150°C)
16(2)
2.7 - 5.5V
ATmega168-15AD
MA
Extended
(-40°C to 150°C)
Notes:
Ordering Code
Package(1)
Speed (MHz)
1. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
2. For Speed vs. Vcc, see complete datasheet.
Package Type
PN
32-pad, 5 x 5 x 1.0 mm body, lead pitch 0.50 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF): E2/D2 3.1 +/0.1mm
MA
MA, 32 - Lead, 7x7 mm Body Size, 1.0 mm Body Thickness 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package
(TQFP)
18
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
PN
19
7607F–AVR–03/08
MA
20
ATMega88/168 Automotive
7607F–AVR–03/08
ATMega88/168 Automotive
Document Revision History
7607F - 01/08
Added memory endurance. See “Memory Endurance” on page 3.
7607E - 11/07
1. Added ATMega168 product offering.
1. Added MA package offering.
7607D - 03/07
1. Updated electrical characteristics.
2. Removed Grade0 qualification section.
3. Updated product part number in ordering information.
7607C - 09/06
4. Ordering and package information updated.
7607B - 08/06
1. Added typical characteristics.
7607A - 01/06
1. Document Creation.
21
7607F–AVR–03/08
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
Enter Product Line E-mail
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
©2008 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are ®, AVR ®, and AVR Studio ® are registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
7607F–AVR–03/08
Similar pages