Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide Smallest Power Entry Module with Metric Fuse Holders GG & HG Series UL Recognized CSA Certified VDE Approved GG1 GG8 GG Series Specifications • Power entry module with enhanced EMI filter • Single or dual fusing • Two element circuit provides basic attenuation • Available with an internal ground-circuit inductor (C versions) to isolate equipment chassis from power line ground at radio frequencies • Multiple termination and mounting styles HG Series • Medical version of our GG Series • Mechanically identical to GG Series Maximum leakage current each Line to Ground: HG Models GG Models @ 120 VAC 60 Hz: 2 A .25 mA @250 VAC 50 Hz: 5 A .42 mA Hipot rating (one minute): Line to Ground: Line to Line: 2250 VDC 1450 VDC Rated Voltage (max.): 250 VAC Operating Frequency: 50/60 Hz Rated Current: 1 to 10A Required Fuse(s): 5 x 20mm (not included) • Available only with dual fusing Ordering Information 3 E GG 1 C -2 Metric Fuse Holders 1 – Single 2 – Double Ground Circuit Inductor Omit if none Output Styles 1 – .250 [6.3] spade terminals 8 – Wire leads GG or HG Series (Flange mount) GGS or HGS Series (Snap-in mount) Leakage current designation E – Low leakage (<0.5 mA) Current Rating 1, 3, 6 or 10A Available Part Numbers Filtered modules 1EGG1-1 3EGG1-1 6EGG1-1 10EGG1-1 1EGG1-2 3EGG1-2 6EGG1-2 10EGG1-2 1EGG8-1 3EGG8-1 6EGG8-1 10EGG8-1 1EGG8-2 3EGG8-2 6EGG8-2 10EGG8-2 1EGS1-1 3EGS1-1 6EGS1-1 10EGS1-1 1EGS1-2 3EGS1-2 6EGS1-2 10EGS1-2 Filtered modules with ground circuit inductor 1EGG1C-1 3EGG1C-1 6EGG1C-1 1EGG1C-2 3EGG1C-2 6EGG1C-2 1EGG8C-1 3EGG8C-1 6EGG8C-1 1EGG8C-2 3EGG8C-2 6EGG8C-2 Medical filter modules 1EHG1-2 3EHG1-2 6EHG1-2 10EHG1-2 1EHG8-2 3EHG8-2 6EHG8-2 10EHG8-2 1EHGS1-2 3EHGS1-2 6EHGS1-2 10EHGS1-2 166 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide Smallest Power Entry Module with Metric Fuse Holders (continued) GG & HG Series Electrical Schematic GG8 & HG8 LINE LOAD 1 Blue 2 3 Green/Yellow B D E Brown 3 Note 1: Second fuse only in -2 version Note 2: C versions only Note 3: not present in HG versions A C Accessories GA400: NEMA 5-15P to IEC 60320-1 C-13 line cord 3 Part No. Case Styles GG1 & HG1 GG1, GG1C & HG1 GG1C GS1, HGS1 C GG8, HG8 D E A A B C D E B Power Inlet Filters & Power Entry Modules Case Dimensions Recommended Panel Cutouts GG / HG GS / HGS 1.14 29.0 1.24 31.5 GS1 & HGS1 1.29 32.8 1.30 33.0 D E C A 1.417 36.0 B Front or Back Mount Front Mount Only 167 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide Smallest Power Entry Module with Metric Fuse Holders (continued) GG & HG Series Performance Data Typical Insertion Loss GG & GS Models Measured in closed 50 Ohm system 1A 3A 6A 10A db 100 db 100 db 100 db 100 90 90 90 90 80 80 80 70 70 70 70 60 60 60 60 80 50 50 50 50 40 40 40 40 30 30 30 30 20 20 20 20 10 10 10 0 0.1 1 10 30 Frequency in MHz 0 0.1 1 3A GG1C 6A GG1C db 100 db 100 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 0 10 30 Frequency in MHz 0 10 0.1 1 0 10 30 Frequency in MHz 0.01 0.1 1 10 30 Frequency in MHz Common Mode / Asymmetrical (L-G) Differential Mode / Symmetrical (L-L) 10 0.1 1 10 30 Frequency in MHz 0 0.1 1 10 30 Frequency in MHz HG Models 1A 3A 6A 10A db 100 db 100 db 100 db 100 90 90 90 90 80 80 80 80 70 70 70 70 60 60 60 60 50 50 50 50 40 40 40 40 30 30 30 30 20 20 20 20 10 10 10 0 0.1 1 10 30 Frequency in MHz 0 0.1 1 Minimum Insertion Loss 10 30 Frequency in MHz 10 0.1 1 0 10 30 Frequency in MHz 0.1 1 10 30 Frequency in MHz Measured in closed 50 Ohm system Common Mode / Asymmetrical (Line to Ground) Differential Mode / Symmetrical (Line to Line) 0 168 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com