SAMTEC MEC1-108-02-SM-D-NP-K 1mm mini-edge card assembly Datasheet

REVISION AD
MEC1-1XX-XX-XX-D-XX-XX
(No OF POS -1) x .03937 [1.00]
.109 2.77
REF
C1
({(No OF POS +2) x .03937 [1.00]}
+ .100 [2.54]) .007[.18]
.005[.13]
DO NOT
SCALE FROM
THIS PRINT
CARD THICKNESS
-02: .062 [1.58] THICK CARD
(USE MEC1-XX-S-D-X-X)
.026 0.66 REF
16
02
FLOW INHIBITORS
AT VENDOR DISCRETION
40
.275 6.99
REF
.072 1.83 REF
15
01
1.5° MAX SWAY
(ANY DIRECTION)
39
-F: FLASH GOLD (USE C-113-02-F)
-L: LIGHT GOLD (USE C-113-02-L)
-S: SELECTIVE GOLD (USE C-113-02-S)
-FM: FLASH GOLD (USE C-113-02-F)/
ROW SPECIFICATION
MATTE TIN TAILS
-D: DOUBLE ROW
-LM: LIGHT GOLD (USE C-113-02-L)/
(USE MEC1-XX-X-D-X-X)
MATTE TIN TAILS
-SM: SELECTIVE GOLD (USE C-113-02-S)/
MATTE TIN TAILS
.160 4.07 REF
C7 .020 0.51
MEC1-XX-X-D-X-X
FIG. 1
(No OF POS +2) x
.03937 [1.00] REF
"A"
MEC1-120-02-X-D SHOWN
SEE NOTE 5
C2
.350 8.89
REF
POLARIZED OPTION (SEE TABLE 2)
-BLANK: BODY IS POLARIZED
-NP: NO POLARIZATION (-05 THRU -30 ONLY)
(USE MEC1-XX-X-D-N-X)
PLATING SPECIFICATION
C6
.050 1.27
OTHER OPTIONS
-LC: LOCKING CLIP
(SEE FIG. 2)(USE LC-05-TM)
-A: ALIGNMENT PIN
(MOLDED, SEE FIG. 4, SHT. 2)
(USE MEC1-XX-X-D-X-A)
-K: POLYIMIDE FILM PAD
(SEE FIG. 6, SHT. 2)(USE K-500-300)
-TR: TAPE & REEL PACKAGING
(N/A IN 70 POSITION)(SEE FIG. 5, SHT. 2)
No OF POSITIONS
05, 08, 20, 30, 40 , 50, 60 & 70
(PER ROW, SEE TABLE 2)
+.004
90°±3°
+0.10
.356 - .002 9.04 - 0.05
"A"
SEE NOTE 2
.334 8.49
C-113-02-XX
.320 8.13
REF
.006 0.15 REF
.030 0.75
.079 2.00
SECTION "A"-"A"
PACKAGING VIEW
IN-PROCESS
(FILL STEP)
40
01
39
MEC1-XX-X-D-N-X
C4
+.005
+0.13
0.00
.535 - .000 13.59
NOTES:
C3
02
1. MINIMUM PUSHOUT FORCE: 10 oz.
2. COPLANARITY: POS -05 THRU -26: .004 [.10]
POS -27 THRU -70: .006 [.15]
3. C REPRESENTS A CRITICAL DIMENSION.
4. PACKAGE ALL POSITIONS IN TUBES.
(WITH -K OPTION, USE PT-1-24-01-70 TUBE & TP-29 TUBE PLUG)
(WITHOUT -K OPTION, USE PT-1-24-01-69 TUBE & TP-07 TUBE PLUG)
5. MAXIMUM CUT FLASH: .010; FLASH NOT TO EXTEND BELOW LEADS.
6. MAXIMUM ALLOWABLE BOW: .002 INCH/INCH AFTER ASSEMBLY.
7. MAXIMUM BURR: .003[.08], BURR DIRECTION TO BE OPPOSITE OF SOLDER PAD AREA
FOR -K OPTION
-NP: NON-POLARIZED OPTION
(AVAILABLE ON -05, -08, -20 & -30 POS. ONLY)
(SHOWN: MEC1-120-02-X-D-NP)
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0015 [.038]
MATERIAL:
NO -K OPTION
TUBE: PT-1-24-01-70
PLUG: TP-29
TUBE: PT-1-24-01-69
PLUG: TP-07
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
INSULATOR:
VECTRA E130i COLOR: BLACK
CONTACT:
BeCu 190 HM
c:\enterprisevault\DWG\MISC\MKTG\MEC1-1XX-XX-XX-D-XX-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: [email protected]
code: 55322
DESCRIPTION:
1mm MINI-EDGE CARD ASSEMBLY
DWG. NO.
MEC1-1XX-XX-XX-D-XX-XX
BY: KEVIN B
5/11/2000
SHEET 1 OF 2
REVISION AD
FIG. 5
.059 1.50 (TYP)
-TR: TAPE & REEL PACKAGING VIEW
(NOT DRAWN TO SCALE)
LC-05-TM
.010 0.25 REF
.056 1.42 REF (TYP)
2 MAX SWAY
(EITHER DIRECTION)
C8
POSITION 1
C5
({(No OF POS +2) x .03937[1.00]}
+ .0490[1.245]) .005[.13]
FIG.2
-LC OPTION
(SHOWN: MEC1-120-02-X-D-LC)
.0625 1.588 REF
MEC1-XX-X-D-X-A
.035 0.89 REF
(TYP)
.055 1.40 REF
({(No OF POS +2) x .03937[1.0000]}
+ .0490[1.245]) REF
.0625 1.59 REF
FIG. 4
-A: ALIGNMENT PIN OPTION (MOLDED)
(SHOWN: MEC1-120-02-X-D-A)
FIG. 6
-K: POLYIMIDE FILM PAD OPTION
(SHOWN: MEC1-120-02-X-D-K)
"M"
"P"
02
01
.376 9.55 REF
USER DIRECTION OF UNREELING
c:\enterprisevault\DWG\MISC\MKTG\MEC1-1XX-XX-XX-D-XX-XX-MKT.SLDDRW
16
15
40
PROPRIETARY NOTE
39
.310 7.87
.361 9.17
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
NOTE: "M" = USED MEASURED DIMENSION (REF)
"P" = {("M" - .310 [7.87]) / 2} .020 [.51]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: [email protected]
code: 55322
DESCRIPTION:
1mm MINI-EDGE CARD ASSEMBLY
DWG. NO.
MEC1-1XX-XX-XX-D-XX-XX
BY: KEVIN B
5/11/2000
SHEET 2 OF 2
Similar pages