TC7MA574FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MA574FK Low-Voltage Octal D-Type Flip-Flop with 3.6 V Tolerant Inputs and Outputs The TC7MA574FK is a high performance CMOS octal D-type flip-flop which is guaranteed to operate from 1.2-V to 3.6-V. Designed for use in 1.5 V, 1.8 V, 2.5 V or 3.3 V systems, it achieves high speed operation while maintaining the CMOS low power dissipation. It is also designed with over voltage tolerant inputs and outputs up to 3.6 V. This 8 bit D-type flip-flop is controlled by a clock input (CK) and an output enable input (OE).When OE input is high, the eight outputs are in a high impedance state. All inputs are equipped with protection circuits against static discharge. Weight: 0.03 g (typ.) Features • Low voltage operation: VCC = 1.2~3.6 V • High speed operation: tpd = 4.2 ns (max) (VCC = 3.0~3.6 V) tpd = 4.8 ns (max) (VCC = 2.3~2.7 V) tpd = 9.6 ns (max) (VCC = 1.65~1.95 V) tpd = 19.2 ns (max) (VCC = 1.4~1.6 V) tpd = 48.0 ns (max) (VCC = 1.2 V) • 3.6 V tolerant inputs and outputs. • Output current: IOH/IOL = ±24 mA (min) (VCC = 3.0 V) IOH/IOL = ±18 mA (min) (VCC = 2.3 V) IOH/IOL = ±6 mA (min) (VCC = 1.65 V) IOH/IOL = ±2 mA (min) (VCC = 1.4 V) • Latch-up performance: −300 mA • ESD performance: Machine model ≥ ±200 V Human body model ≥ ±2000 V • Package: VSSOP (US) • Power down protection is provided on all inputs and outputs. 1 2007-10-19 TC7MA574FK Pin Assignment (top view) IEC Logic Level OE 1 20 VCC D0 2 19 Q0 D1 3 18 Q1 D2 4 17 Q2 D3 5 16 Q3 D4 6 15 Q4 D5 7 14 Q5 OE CK D0 D1 D2 D3 D6 8 13 Q6 D7 9 12 Q7 GND 10 11 CK D4 D5 D6 D7 (1) (11) EN C1 (2) (19) 1D (3) (18) (4) (17) (5) (16) (6) (15) (7) (14) (8) (13) (9) (12) Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Truth Table Inputs Outputs OE CK D H X X Z X Qn L L L L L H H X: Don’t care Z: High impedance Qn: No change System Diagram D1 3 D0 2 D CK OE 11 D2 4 D CK Q D3 5 D CK Q D4 6 D CK Q D5 7 D CK Q D6 8 D CK Q D7 9 D CK Q D CK Q Q CK 1 19 Q0 18 Q1 17 16 Q2 Q3 2 15 Q4 14 Q5 13 Q6 12 Q7 2007-10-19 TC7MA574FK Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Power supply voltage VCC −0.5~4.6 V DC input voltage VIN −0.5~4.6 V −0.5~4.6 (Note 2) DC output voltage VOUT Input diode current IIK −50 Output diode current IOK ±50 DC output current IOUT ±50 mA Power dissipation PD 180 mW ICC/IGND ±100 mA Tstg −65~150 °C DC VCC/ground current Storage temperature V −0.5~VCC + 0.5 (Note 3) mA (Note 4) mA Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: VCC = 0 V Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC Operating Ranges (Note 1) Characteristics Symbol Rating Unit Supply voltage VCC 1.2~3.6 V Input voltage VIN −0.3~3.6 V Output voltage Output current VOUT IOH/IOL 0~3.6 (Note 2) 0~VCC (Note 3) ±24 (Note 4) ±18 (Note 5) ±6 (Note 6) ±2 (Note 7) Operating temperature Topr −40~85 Input rise and fall time dt/dv 0~10 V mA °C (Note 8) ns/V Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Off-state Note 3: High or low state Note 4: VCC = 3.0~3.6 V Note 5: VCC = 2.3~2.7 V Note 6: VCC = 1.65~1.95 V Note 7: VCC = 1.4~1.6 V Note 8: VIN = 0.8~2.0 V, VCC = 3.0 V 3 2007-10-19 TC7MA574FK Electrical Characteristics DC Characteristics (Ta = −40~85°C, 2.7 V < VCC =< 3.6 V) Characteristics Input voltage Symbol Test Condition High level VIH ⎯ Low level VIL ⎯ High level VOH Min Max 2.7~3.6 2.0 ⎯ 2.7~3.6 ⎯ 0.8 IOH = −100 μA 2.7~3.6 VCC − 0.2 ⎯ IOH = −12 mA 2.7 2.2 ⎯ IOH = −18 mA 3.0 2.4 ⎯ IOH = −24 mA 3.0 2.2 ⎯ IOL = 100 μA 2.7~3.6 ⎯ 0.2 IOL = 12 mA 2.7 ⎯ 0.4 IOL = 18 mA 3.0 ⎯ 0.4 IOL = 24 mA 3.0 ⎯ 0.55 2.7~3.6 ⎯ ±5.0 μA 2.7~3.6 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 2.7~3.6 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.7~3.6 ⎯ ±20.0 VIH = VCC − 0.6 V (per input) 2.7~3.6 ⎯ 750 Min Max VIN = VIH or VIL Output voltage Low level VOL Input leakage current IIN 3-state output off-state current IOZ Power off leakage current IOFF Quiescent supply current ICC ΔICC VIN = VIH or VIL VIN = 0~3.6 V VIN = VIH or VIL VOUT = 0~3.6 V VIN, VOUT = 0~3.6 V VCC (V) Unit V V μA DC Characteristics (Ta = −40~85°C, 2.3 V =< VCC =< 2.7 V) Characteristics Input voltage Symbol Test Condition High level VIH ⎯ 2.3~2.7 1.6 ⎯ Low level VIL ⎯ 2.3~2.7 ⎯ 0.7 2.3~2.7 VCC − 0.2 ⎯ IOH = −6 mA 2.3 2.0 ⎯ IOH = −12 mA 2.3 1.8 ⎯ IOH = −18 mA 2.3 1.7 ⎯ IOL = 100 μA 2.3~2.7 ⎯ 0.2 IOL = 12 mA 2.3 ⎯ 0.4 IOL = 18 mA 2.3 ⎯ 0.6 2.3~2.7 ⎯ ±5.0 μA 2.3~2.7 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 2.3~2.7 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.3~2.7 ⎯ ±20.0 IOH = −100 μA High level VOH VIN = VIH or VIL Output voltage Low level VOL Input leakage current IIN 3-state output off-state current IOZ Power off leakage current IOFF Quiescent supply current ICC VIN = VIH or VIL VIN = 0~3.6 V VIN = VIH or VIL VOUT = 0~3.6 V VIN, VOUT = 0~3.6 V 4 VCC (V) Unit V V μA 2007-10-19 TC7MA574FK DC Characteristics (Ta = −40~85°C, 1.65 V =< VCC < 2.3 V) Characteristics Symbol Test Condition High level VIH ⎯ Low level VIL ⎯ High level VOH Min Max 1.65~2.3 0.65 × VCC ⎯ 1.65~2.3 ⎯ 0.2 × VCC 1.65~2.3 VCC − 0.2 ⎯ 1.65 1.25 ⎯ ⎯ 0.2 1.65 ⎯ 0.3 1.65~2.3 ⎯ ±5.0 μA 1.65 ⎯ ±10.0 μA μA VCC (V) Input voltage IOH = −100 μA VIN = VIH or VIL IOH = −6 mA Output voltage Low level VOL Input leakage current IIN 3-state output off-state current IOZ Power off leakage current IOFF Quiescent supply current ICC IOL = 100 μA VIN = VIH or VIL IOL = 6 mA VIN = 0~3.6 V VIN = VIH or VIL VOUT = 0~3.6 V VIN, VOUT = 0~3.6 V 1.65~2.3 0 ⎯ 10.0 VIN = VCC or GND 1.65~2.3 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 1.65~2.3 ⎯ ±20.0 Unit V V μA DC Characteristics (Ta = −40~85°C, 1.4V =< VCC <1.65 V) Characteristics Symbol Test Condition High level VIH ⎯ Low level VIL ⎯ High level VOH Min Max 1.4~1.65 0.65 × VCC ⎯ 1.4~1.65 ⎯ 0.05 × VCC 1.4~1.65 VCC − 0.2 ⎯ IOH = −2 mA 1.4 1.05 ⎯ IOL = 100 μA 1.4~1.65 ⎯ 0.05 1.4 ⎯ 0.35 1.4~1.65 ⎯ ±5.0 μA 1.4~1.65 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 1.4~1.65 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 1.4~1.65 ⎯ ±20.0 VCC (V) Input voltage IOH = −100 μA VIN = VIH or VIL Output voltage Low level VOL Input leakage current IIN 3-state output off-state current IOZ Power off leakage current IOFF Quiescent supply current ICC VIN = VIH or VIL IOL = 2 mA VIN = 0~3.6 V VIN = VIH or VIL VOUT = 0~3.6 V VIN, VOUT = 0~3.6 V 5 Unit V V μA 2007-10-19 TC7MA574FK DC Characteristics (Ta = −40~85°C, 1.2 V =< VCC < 1.4 V) Characteristics Input voltage Output voltage Symbol Test Condition High level VIH ⎯ Low level VIL ⎯ High level VOH VIN = VIH or VIL Low level VOL VIN = VIH or VIL Input leakage current IIN 3-state output off-state current IOZ Power off leakage current IOFF Quiescent supply current ICC Min Max 1.2~1.4 0.8 × VCC ⎯ 1.2~1.4 ⎯ 0.05 × VCC IOH = −100 μA 1.2 VCC − 0.1 ⎯ IOL = 100 μA 1.2 ⎯ 0.05 1.2 ⎯ ±5.0 μA 1.2 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 1.2 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 1.2 ⎯ ±20.0 VIN = 0~3.6 V VIN = VIH or VIL VOUT = 0~3.6 V VIN, VOUT = 0~3.6 V 6 VCC (V) Unit V V μA 2007-10-19 TC7MA574FK AC Characteristics (Ta = −40~85°C, Input: tr = tf = 2.0 ns) Characteristics Symbol Test Condition CL = 15 pF, RL = 2 kΩ Maximum clock frequency fmax Figure 1, Figure 2 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ Propagation delay time (CK-Q) tpLH tpHL Figure 1, Figure 2 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ 3-state output enable time tpZL tpZH Figure 1, Figure 3 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ 3-state output disable time tpLZ tpHZ Figure 1, Figure 3 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ Minimum pulse width (CK) tw (H) tw (L) Figure 1, Figure 2 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ Minimum set-up time ts Figure 1, Figure 2 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ Minimum hold time th Figure 1, Figure 2 CL = 30 pF, RL = 500 Ω CL = 15 pF, RL = 2 kΩ Output to output skew tosLH tosHL (Note) CL = 30 pF, RL = 500 Ω Min Max 1.2 40 ⎯ 1.5 ± 0.1 80 ⎯ 1.8 ± 0.15 100 ⎯ 2.5 ± 0.2 200 ⎯ 3.3 ± 0.3 250 ⎯ 1.2 1.5 48 VCC (V) 1.5 ± 0.1 1.0 19.2 1.8 ± 0.15 1.5 9.6 2.5 ± 0.2 0.8 4.8 3.3 ± 0.3 0.6 4.2 1.2 1.5 49.0 1.5 ± 0.1 1.0 19.6 1.8 ± 0.15 1.5 9.8 2.5 ± 0.2 0.8 5.5 3.3 ± 0.3 0.6 4.5 1.2 1.5 32.5 1.5 ± 0.1 1.0 13.0 1.8 ± 0.15 1.5 6.5 2.5 ± 0.2 0.8 3.6 3.3 ± 0.3 0.6 3.3 1.2 24 ⎯ 1.5 ± 0.1 8.0 ⎯ 1.8 ± 0.15 4.0 ⎯ 2.5 ± 0.2 1.5 ⎯ 3.3 ± 0.3 1.5 ⎯ 1.2 20 ⎯ 1.5 ± 0.1 7.5 ⎯ 1.8 ± 0.15 2.5 ⎯ 2.5 ± 0.2 1.5 ⎯ 3.3 ± 0.3 1.5 ⎯ 1.2 8.0 ⎯ 1.5 ± 0.1 3.0 ⎯ 1.8 ± 0.15 1.0 ⎯ 2.5 ± 0.2 1.0 ⎯ 3.3 ± 0.3 1.0 ⎯ 1.2 ⎯ 1.5 1.5 ± 0.1 ⎯ 1.5 1.8 ± 0.15 ⎯ 0.5 2.5 ± 0.2 ⎯ 0.5 3.3 ± 0.3 ⎯ 0.5 Unit MHz ns ns ns ns ns ns ns For CL = 50 pF, add approximately 300 ps to the AC maximum specification. Note: This parameter is guaranteed by design. (tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn|) 7 2007-10-19 TC7MA574FK Dynamic Switching Characteristics (Ta = 25°C, Input: tr = tf = 2.0 ns, CL = 30 pF) Characteristics Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL Quiet output minimum dynamic VOH Symbol VOLP VOLV VOHV Test Condition VCC (V) Typ. VIH = 1.8 V, VIL = 0 V (Note) 1.8 0.25 VIH = 2.5 V, VIL = 0 V (Note) 2.5 0.6 VIH = 3.3 V, VIL = 0 V (Note) 3.3 0.8 VIH = 1.8 V, VIL = 0 V (Note) 1.8 −0.25 VIH = 2.5 V, VIL = 0 V (Note) 2.5 −0.6 VIH = 3.3 V, VIL = 0 V (Note) 3.3 −0.8 VIH = 1.8 V, VIL = 0 V (Note) 1.8 1.5 VIH = 2.5 V, VIL = 0 V (Note) 2.5 1.9 VIH = 3.3 V, VIL = 0 V (Note) 3.3 2.2 Unit V V V Note: This parameter is guaranteed by design. Capacitive Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Input capacitance CIN ⎯ Output capacitance CO ⎯ Power dissipation capacitance CPD fIN = 10 MHz Typ. Unit 1.8, 2.5, 3.3 6 pF 1.8, 2.5, 3.3 7 pF 1.8, 2.5, 3.3 20 pF VCC (V) (Note) Note: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/8 (per bit) 8 2007-10-19 TC7MA574FK AC Test Circuit 6.0 V or VCC × 2 Open GND RL Switch Parameter VCC Switch tpLH, tpHL tpLZ, tpZL RL Measure CL Output Open 6.0 V VCC × 2 @VCC = 3.3 ± 0.3 V @VCC = 2.5 ± 0.2 V @VCC = 1.8 ± 0.15 V @VCC = 1.5 ± 0.1 V @VCC = 1.2 V tpHZ, tpZH Symbol 3.3 ± 0.3 V 2.5 ± 0.2 V 1.8 ± 0.15 V 1.5 ± 0.1 V 1.2 V RL 500Ω 2kΩ CL 30pF 15pF GND Figure 1 AC Waveform tr 2.0 ns Input (CK) 10% tf 2.0 ns VIH 90% VM GND tr 2.0 ns Input (D) tw (H) VIH 90% 10% tw (L) VM ts (H) Output (Q) tf 2.0 ns th (H) ts (L) th (L) GND VOH VM tpHL tpLH VOL Figure 2 tpLH, tpHL, tw, ts, th 9 2007-10-19 TC7MA574FK tf 2.0 ns tr 2.0 ns 90% VM Output Enable Control ( OE ) VIH 10% tpLZ GND tpZL 3.0 V or VCC Output (Q) Low to Off to Low tpHZ VM VX VOH VY Output (Q) High to Off to High VOL tpZH VM GND Outputs enabled Outputs disabled Outputs enabled Figure 3 tpLZ, tpHZ, tpZL, tpZH Symbol VCC 3.3 ± 0.3 V 2.5 ± 0.2 V 1.8 ± 0.15 V 1.5 ± 0.1 V 1.2 V VIH 2.7 V VCC VCC VCC VCC VM 1.5 V VCC/2 VCC/2 VCC/2 VCC/2 VX VOL + 0.3 V VOL + 0.15 V VOL + 0.15 V VOL + 0.1 V VOL + 0.1 V VY VOH − 0.3 V VOH − 0.15 V VOH − 0.15 V VOH − 0.1 V VOH − 0.1 V 10 2007-10-19 TC7MA574FK Package Dimensions Weight: 0.03 g (typ.) 11 2007-10-19 TC7MA574FK RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 12 2007-10-19