MICREL MIC37100

MIC37100/37101/37102
Micrel
MIC37100/37101/37102
1A Low-Voltage µCap LDO Regulator
General Description
Features
The MIC37100, MIC37101, and MIC37102 are 1A lowdropout, linear voltage regulators that provide low-voltage,
high-current output from an extremely small package. Utilizing Micrel’s proprietary Super βeta PNP™ pass element, the
MIC37100/01/02 offers extremely low dropout (typically
280mV at 1A) and low ground current (typically 11mA at 1A).
The MIC37100 is a fixed output regulator offered in the
SOT-223 package. The MIC37101 and MIC37102 are fixed
and adjustable regulators, respectively, in a thermally enhanced power 8-lead SOIC (small outline package) and the
SOT-223 package. The MIC37102 is also available in the SPAK power package, for applications that require higher
power dissipation or higher operating ambient temperatures.
The MIC37100/01/02 is ideal for PC add-in cards that need
to convert from standard 5V to 3.3V, 3.3V to 2.5V or 2.5V to
1.8V or lower. A guaranteed maximum dropout voltage of
500mV over all operating conditions allows the
MIC37100/01/02 to provide 2.5V from a supply as low as 3V
and 1.8V from a supply as low as 2.3V.
The MIC37100/01/02 is fully protected with overcurrent limiting and thermal shutdown. Fixed output voltages of 1.5V,
1.65V, 1.8V, 2.5V and 3.3V are available on MIC37100/01
with adjustable output voltages to 1.24V on MIC37102.
• Fixed and adjustable output voltages to 1.24V
µF ceramic output capacitor
• µCap Regulator, 10µ
stable
• 280mV typical dropout at 1A
Ideal for 3.0V to 2.5V conversion
Ideal for 2.5V to 1.8V, 1.65V or 1.5V conversion
• 1A minimum guaranteed output current
• 1% initial accuracy
• Low ground current
• Current limiting and thermal shutdown
• Reversed-leakage protection
• Fast transient response
• Low-profile SOT-223 package
• Power SO-8 package
• S-PAK package (MIC37102 only)
Applications
•
•
•
•
•
•
•
For other voltages, contact Micrel.
LDO linear regulator for PC add-in cards
PowerPC™ power supplies
High-efficiency linear power supplies
SMPS post regulator
Multimedia and PC processor supplies
Battery chargers
Low-voltage microcontrollers and digital logic
All support documentation can be found on Micrel’s web
site at www.micrel.com.
Typical Applications
Dropout
vs. Output Current
350
300
MIC37100
IN
OUT
GND
2.5V
DROPOUT (mV)
VIN
3.3V
10µF
ceramic
2.5V/1A Regulator
2.5VOUT
250
200
150
3.3VOUT
100
50
0
0
0.25
0.5
0.75
OUTPUT CURRENT (A)
1
Super βeta PNP is a registered trademark of Micrel, Inc.
PowerPC is a trademark of IBM Corporation.
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
September 2004
1
M9999-091604
MIC37100/37101/37102
Micrel
Ordering Information
Part Number
Voltage
Junction Temp. Range
Package
MIC37100-1.5BS
1.5V
–40°C to +125°C
SOT-223
MIC37100-1.65BS
1.65V
–40°C to +125°C
SOT-223
MIC37100-1.8BS
1.8V
–40°C to +125°C
SOT-223
MIC37100-2.5BS
2.5V
–40°C to +125°C
SOT-223
MIC37100-3.3BS
3.3V
–40°C to +125°C
SOT-223
MIC37101-1.5BM
1.5V
–40°C to +125°C
SOIC-8
MIC37101-1.65BM
1.65V
–40°C to +125°C
SOIC-8
MIC37101-1.8BM
1.8V
–40°C to +125°C
SOIC-8
MIC37101-2.5BM
2.5V
–40°C to +125°C
SOIC-8
MIC37101-3.3BM
3.3V
–40°C to +125°C
SOIC-8
MIC37102BM
Adj.
–40°C to +125°C
SOIC-8
MIC37101-1.5YM
1.5V
–40°C to +125°C
SOIC-8 Lead Free
MIC37101-1.65YM
1.65V
–40°C to +125°C
SOIC-8 Lead Free
MIC37101-1.8YM
1.8V
–40°C to +125°C
SOIC-8 Lead Free
MIC37101-2.5YM
2.5V
–40°C to +125°C
SOIC-8 Lead Free
MIC37101-3.3YM
3.3V
–40°C to +125°C
SOIC-8 Lead Free
MIC37102YM
Adj.
–40°C to +125°C
SOIC-8 Lead Free
MIC37102BR
Adj.
–40°C to +125°C
S-PAK-5
Pin Configuration
GND
TAB
TAB
5
4
3
2
1
1
IN
2
3
GND OUT
MIC37100-x.x (Fixed)
SOT-223 (S)
MIC37102 (Adjustable)
S-PAK-5 (R)
EN 1
8 GND
EN 1
8 GND
IN 2
7 GND
IN 2
7 GND
OUT 3
6 GND
OUT 3
6 GND
FLG 4
5 GND
ADJ 4
5 GND
MIC37101-x.x (Fixed)
SOIC-8 (M)
M9999-091604
ADJ
OUT
GND
IN
EN
MIC37102 (Adjustable)
SOIC-8 (M)
2
September 2004
MIC37100/37101/37102
Micrel
Pin Description
Pin No.
MIC37100
SOT-223
Pin No.
MIC37101
SOIC-8
Pin No.
MIC37102
SOIC-8
Pin No.
MIC37102
S-PAK
Pin Name
1
1
1
1
EN
Enable (Input): CMOS-compatible control input. Logic high =
enable, logic low or open = shutdown.
2
2
2
IN
Supply (Input).
3
3
4
OUT
Regulator Output.
FLG
Flag (Output): Open-collector error flag output. Active low =
output under voltage.
3
4
2, TAB
5–8
September 2004
Pin Function
4
5
ADJ
Adjustment Input: Feedback input. Connect to resistive
voltage-divider network.
5–8
3, TAB
GND
Ground.
3
M9999-091604
MIC37100/37101/37102
Micrel
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN) ........................................ 0V to +6.5V
Enable Voltage (VEN) ................................................. +6.5V
Storage Temperature (TS) ....................... –65°C to +150°C
Lead Temperature (soldering, 5 sec.) ....................... 260°C
ESD ................................................................................ (3)
Supply Voltage (VIN) .................................... +2.25V to +6V
Enable Voltage (VEN) .......................................... 0V to +6V
Maximum Power Dissipation (P
) ........................... (4)
D(max)
Junction Temperature (TJ) ....................... –40°C to +125°C
Package Thermal Resistance
SOT-223 (θJC) ..................................................... 15°C/W
SOIC-8 (θJC) ....................................................... 20°C/W
S-PAK-5 (θJC) ....................................................... 2°C/W
Electrical Characteristics
VIN = VOUT + 1V; VEN = 2.25V; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted
Symbol
Parameter
Condition
VOUT
Output Voltage
10mA
10mA ≤ IOUT ≤ 1A, VOUT + 1V ≤ VIN ≤ 6V
Line Regulation
IOUT = 10mA, VOUT + 1V ≤ VIN ≤ 6V
Load Regulation
VIN = VOUT + 1V, 10mA ≤ IOUT ≤ 1A,
∆VOUT/∆T
Output Voltage Temp. Coefficient(6)
VDO
Dropout Voltage(6)
IGND
IOUT(lim)
Min
Typ
Max
Units
1
2
%
%
0.06
0.5
%
0.2
1
%
–1
–2
40
ppm/°C
IOUT = 100mA, ∆VOUT = –1%
125
200
mV
IOUT = 500mA, ∆VOUT = –1%
210
350
mV
IOUT = 750mA, ∆VOUT = –1%
250
400
mV
IOUT = 1A, ∆VOUT = –1%
280
500
mV
IOUT = 100mA, VIN = VOUT + 1V
650
mA
IOUT = 500mA, VIN = VOUT + 1V
3.5
mA
IOUT = 750mA, VIN = VOUT + 1V
6.7
mA
IOUT = 1A, VIN = VOUT + 1V
11
25
mA
Current Limit
VOUT = 0V, VIN = VOUT + 1V
1.6
2.5
A
Enable Input Voltage
logic low (off)
0.8
V
Ground Current(7)
Enable Input
VEN
logic high (on)
IEN
Enable Input Current
VEN = 2.25V
2.25
1
V
10
VEN = 0.8V
30
µA
2
4
µA
µA
Flag Output
IFLG(leak)
Output Leakage Current
VOH = 6V
0.01
1
2
µA
µA
VFLG(do)
Output Low Voltage
VIN = 2.250V, IOL, = 250µA
210
500
mV
VFLG
Low Threshold
% of VOUT
High Threshold
% of VOUT
93
99.2
Hysteresis
M9999-091604
%
1
4
%
%
September 2004
MIC37100/37101/37102
Symbol
Parameter
Micrel
Condition
Min
Typ
Max
Units
1.228
1.215
1.240
1.252
1.265
V
V
40
80
120
nA
nA
MIC37102 Only
Reference Voltage
Adjust Pin Bias Current
Notes:
1. Exceeding the absolute maximum ratings may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended.
4. PD(max) = (TJ(max) – TA) ÷ θJA, where θJA depends upon the printed circuit layout. See “Applications Information” section.
5. Output voltage temperature coefficient is ∆VOUT(worst case) ÷ (TJ(max) – TJ(min)) where TJ(max) is +125°C and TJ(min) is –40°C.
6. VDO = VIN – VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1V. For output voltages below 2.25V, dropout
voltage is the input-to-output voltage differential with the minimum input voltage being 2.25V. Minimum input operating voltage is 2.25V.
7. IGND is the quiescent current. IIN = IGND + IOUT.
8. VEN ≤ 0.8V, VIN ≤ 6V, and VOUT = 0V.
September 2004
5
M9999-091604
MIC37100/37101/37102
Micrel
Typical Characteristics
Power Supply
Rejection Ratio
Power Supply
Rejection Ratio
80
80
VIN = 5V
VOUT = 3.3V
70
30
50
40
30
IOUT = 1000mA
COUT = 10µF
10 C = 0
IN
IOUT = 1000mA
COUT = 47µF
10 C = 0
IN
0
0.01 0.1
1
10
100
FREQUENCY (KHz)
20
0.1
1
10
100
FREQUENCY (KHz)
1000
40
30
IOUT = 1000mA
COUT = 47µF
10 C = 0
IN
20
250
200
3.3VOUT
150
100
0
0.1
1
10
100
FREQUENCY (KHz)
1000
0
OUTPUT VOLTAGE (V)
150
0.25
0.5
0.75
OUTPUT CURRENT (A)
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
1
Dropout Characteristics
(2.5V)
3.0
1000mA Load
0.6
0.4
0.2
1.7
1.9
2.1
2.3
INPUT VOLTAGE (V)
1.2
1.0
0.4
0.2
0.0
1.5
2.5
1000mA Load
0.8
0.6
1.7 1.9 2.1 2.3 2.5
INPUT VOLTAGE (V)
GROUND CURRENT (mA)
2.0
1000mA Load
1.0
0.5
4
1000mA Load
1.0
0.5
2
2.5
3
INPUT VOLTAGE (V)
3.5
0.8
10
8
6
4 1.5V
OUT
3.3VOUT
2
0
2
2.5
3
3.5
INPUT VOLTAGE (V)
1.5
Ground Current
vs. Supply Voltage (1.5V)
12
2.5
2.0
Ground Current
vs. Output Current
3.5
10mA Load
10mA Load
2.5
0
1.5
2.7
GROUND CURRENT (mA)
OUTPUT VOLTAGE (V)
200
50
1.6
1.4
Dropout Characteristics
(3.3V)
OUTPUT VOLTAGE (V)
2.5VOUT
250
2.0
10mA Load
1.8
1
M9999-091604
300
Dropout Characteristics
(1.8V)
1.2
0
1.5
350
100
10mA Load
1.5
400
50
1.4
3.0
1000
450
Dropout Characteristics
(1.5V)
0
1.5
0.1
1
10
100
FREQUENCY (KHz)
Dropout
vs. Temperature
DROPOUT (mV)
DROPOUT (mV)
PSRR (dB)
50
0.8
0
0.01
1000
2.5VOUT
300
60
0
0.01
30
20
350
VIN = 3.3V
VOUT = 2.5V
70
40
Dropout
vs. Output Current
Power Supply
Rejection Ratio
80
50
IOUT = 1000mA
COUT = 10µF
10 C = 0
IN
20
OUTPUT VOLTAGE (V)
0
0.01
60
PSRR (dB)
PSRR (dB)
PSRR (dB)
40
VIN = 3.3V
VOUT = 2.5V
70
60
50
1.6
80
VIN = 5V
VOUT = 3.3V
70
60
Power Supply
Rejection Ratio
0
0.25
0.5
0.75
OUTPUT CURRENT (A)
6
1
0.7
0.6
100mA
0.5
0.4
0.3
0.2
10mA
0.1
0
0
1
2
3
4
5
INPUT VOLTAGE (V)
6
September 2004
MIC37100/37101/37102
Micrel
Ground Current
vs. Supply Voltage (1.5V)
Ground Current
vs. Supply Voltage (1.8V)
0.8
14
12
1000mA
10
8
6
4
750mA
2
1
2
3
4
5
INPUT VOLTAGE (V)
0.6
100mA
0.5
0.4
0.3
0.2
10mA
0.1
0
6
0
Ground Current
vs. Supply Voltage (2.5V)
100mA
0.6
0.4
10mA
1
2
3
4
5
INPUT VOLTAGE (V)
25
20
15
6
5
750mA
GROUND CURRENT (mA)
GROUND CURRENT (mA)
25
20
750mA
10
500mA
1
2
3
4
5
INPUT VOLTAGE (V)
6
10
2.5VOUT
6
4
OUTPUT VOLTAGE (V)
GROUND CURRENT (mA)
12
1
2
3
4
5
INPUT VOLTAGE (V)
0.4
0.2
5
4.5
4
0.3
2.5VOUT
0.2
0.15
0.1
0.05
IOUT=10mA
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
2.55
2.5
2.5VOUT
2.45
2.4
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
7
10mA
1
2
3
4
5
INPUT VOLTAGE (V)
6
Ground Current
vs. Temperature
0.4
0.25
100mA
0.6
0
0
6
IOUT=1000mA
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
September 2004
0
2.6
14
6
1
0.8
3.5
3
2.5
2
2.5VOUT
1.5
1
0.5
IOUT=500mA
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
Output Voltage
vs. Temperature
16
2
1
2
3
4
5
INPUT VOLTAGE (V)
1.2
0.35
Ground Current
vs. Temperature
8
750mA
Ground Current
vs. Temperature
Ground Current
vs. Supply Voltage (3.3V)
5
1000mA
10
0
30
15
5
1.4
GROUND CURRENT (mA)
0.2
1000mA
10
Ground Current
vs. Supply Voltage (3.3V)
GROUND CURRENT (mA)
GROUND CURRENT (mA)
GROUND CURRENT (mA)
1
0
0
6
30
1.2
0.8
15
Ground Current
vs. Supply Voltage (2.5V)
1.4
0
0
1
2
3
4
5
INPUT VOLTAGE (V)
20
0
0
Short Circuit Current
vs. Supply Voltage
SHORT CIRCUIT CURRENT (A)
0
0
25
0.7
GROUND CURRENT (mA)
16
GROUND CURRENT (mA)
GROUND CURRENT (mA)
18
Ground Current
vs. Supply Voltage (1.8V)
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
2.25
3
3.75 4.5 5.25
SUPPLY VOLTAGE (V)
6
M9999-091604
MIC37100/37101/37102
Micrel
1.4
2.5VIN
1.2
1.0
0.8
0.6
0.4
0.8
3.3VIN
0.6
5VIN
2.5VIN
0.4
0.2
0.2
0
0 0.5 1 1.5 2 2.5 3 3.5 4
FLAG CURRENT (mA)
0.0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
5
4
3
2
Flag Low (FAULT)
1
0
0.01
0.1
1
10
100 1000 10000
RESISTANCE (kΩ)
M9999-091604
250
200
150
100
50
Flag Current = 250µA
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
9
VIN=5V
ENABLE CURRENT (µA)
Flag High (OK)
300
Enable Current
vs. Temperature
Error Flag Pull-Up Resistor
6
FLAG LOW VOLTAGE (mV)
350
1.6
FLAG VOLTAGE (V)
SHORT CIRCUIT CURRENT (A)
1.0
1.8
FLAG VOLTAGE (V)
Flag Low Voltage
vs. Temperature
Flag Voltage
vs. Flag Current
Short Circuit Current
vs. Temperature
8
7
6
5
4
2.5VEN
3
2
1
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
8
September 2004
MIC37100/37101/37102
Micrel
Functional Characteristics
Load Transient Response
OUTPUT VOLTAGE
(200mV/div)
OUTPUT VOLTAGE
(200mV/div)
Load Transient Response
VIN = 3.3V
VOUT = 2.5V
COUT = 10µF Ceramic
100mA
Line Transient Response
Enable Transient Response
ENABLE VOLTAGE
(2V/div)
TIME (400µs/div.)
5V
3.3V
OUTPUT VOLTAGE
(1V/div)
VOUT = 2.5V
COUT = 10µF Ceramic
Load=100mA
TIME (400µs/div.)
September 2004
10mA
TIME (400µs/div.)
INPUT VOLTAGE
(2V/div)
OUTPUT VOLTAGE
(50mV/div)
1000mA
LOAD CURRENT
(500mA/div)
LOAD CURRENT
(500mA/div)
1000mA
VIN = 3.3V
VOUT = 2.5V
COUT = 10µF Ceramic
VIN = 3.3V
VOUT = 2.5V
IOUT = 100mA
COUT = 10µF Ceramic
TIME (10µs/div.)
9
M9999-091604
MIC37100/37101/37102
Micrel
Functional Diagrams
OUT
IN
1.240V
Ref.
Thermal
Shutdown
MIC37100
MIC37100 Fixed Regulator Block Diagram
OUT
IN
1.180V
FLAG
Ref.
1.240V
EN
Thermal
Shutdown
GND
MIC37101
MIC37101 Fixed Regulator with Flag and Enable Block Diagram
OUT
IN
Ref.
1.240V
ADJ
EN
Thermal
Shutdown
GND
MIC37102
MIC37102 Adjustable Regulator Block Diagram
M9999-091604
10
September 2004
MIC37100/37101/37102
Micrel
Input Capacitor
An input capacitor of 1µF or greater is recommended when
the device is more than 4 inches away from the bulk ac supply
capacitance or when the supply is a battery. Small, surface
mount, ceramic chip capacitors can be used for bypassing.
Larger values will help to improve ripple rejection by bypassing the input to the regulator, further improving the integrity of
the output voltage.
Error Flag
The MIC37101 features an error flag (FLG), which monitors
the output voltage and signals an error condition when this
voltage drops 5% below its expected value. The error flag is
an open-collector output that pulls low under fault conditions
and may sink up to 10mA. Low output voltage signifies a
number of possible problems, including an overcurrent fault
(the device is in current limit) or low input voltage. The flag
output is inoperative during overtemperature conditions. A
pull-up resistor from FLG to either VIN or VOUT is required for
proper operation. For information regarding the minimum and
maximum values of pull-up resistance, refer to the graph in
the “Typical Characteristics” section of the data sheet.
Enable Input
The MIC37101 and MIC37102 versions feature an activehigh enable input (EN) that allows on-off control of the
regulator. Current drain reduces to “zero” when the device is
shutdown, with only microamperes of leakage current. The
EN input has TTL/CMOS compatible thresholds for simple
logic interfacing. EN may be directly tied to VIN and pulled up
to the maximum supply voltage
Transient Response and 3.3V to 2.5V or 2.5V to 1.8V,
1.65V or 1.5V Conversion
The MIC37100/01/02 has excellent transient response to
variations in input voltage and load current. The device has
been designed to respond quickly to load current variations
and input voltage variations. Large output capacitors are not
required to obtain this performance. A standard 10µF output
capacitor, is all that is required. Larger values help to improve
performance even further.
By virtue of its low-dropout voltage, this device does not
saturate into dropout as readily as similar NPN-based designs. When converting from 3.3V to 2.5V or 2.5V to 1.8V, or
lower, the NPN based regulators are already operating in
dropout, with typical dropout requirements of 1.2V or greater.
To convert down to 2.5V or 1.8V without operating in dropout,
NPN-based regulators require an input voltage of 3.7V at the
very least. The MIC37100 regulator will provide excellent
performance with an input as low as 3.0V or 2.5V respectively. This gives the PNP based regulators a distinct advantage over older, NPN based linear regulators.
Applications Information
The MIC37100/01/02 is a high-performance low-dropout
voltage regulator suitable for moderate to high-current voltage regulator applications. Its 500mV dropout voltage at full
load and overtemperature makes it especially valuable in
battery-powered systems and as high-efficiency noise filters
in post-regulator applications. Unlike older NPN-pass transistor designs, where the minimum dropout voltage is limited
by the base-to-emitter voltage drop and collector-to-emitter
saturation voltage, dropout performance of the PNP output of
these devices is limited only by the low VCE saturation
voltage.
A trade-off for the low dropout voltage is a varying base drive
requirement. Micrel’s Super βeta PNP™ process reduces
this drive requirement to only 2% of the load current.
The MIC37100/01/02 regulator is fully protected from damage due to fault conditions. Linear current limiting is provided.
Output current during overload conditions is constant. Thermal shutdown disables the device when the die temperature
exceeds the maximum safe operating temperature. The
output structure of these regulators allows voltages in excess
of the desired output voltage to be applied without reverse
current flow.
VIN
MIC37100-x.x
IN
CIN
VOUT
OUT
GND
COUT
Figure 1. Capacitor Requirements
Output Capacitor
The MIC37100/01/02 requires an output capacitor to maintain stability and improve transient response. As a µCap
LDO, the MIC37100/01/02 can operate with ceramic output
capacitors as long as the amount of capacitance is 10µF or
greater. For values of output capacitance lower than 10µF,
the recommended ESR range is 200mΩ to 2Ω. The minimum
value of output capacitance recommended for the MIC37100/
01/02 is 4.7µF.
For 10µF or greater the ESR range recommended is less than
1Ω. Ultra-low ESR ceramic capacitors are recommended for
output capacitance of 10µF or greater to help improve transient response and noise reduction at high frequency.
X7R/X5R dielectric-type ceramic capacitors are recommended because of their temperature performance. X7Rtype capacitors change capacitance by 15% over their operating temperature range and are the most stable type of
ceramic capacitors. Z5U and Y5V dielectric capacitors change
value by as much as 50% and 60% respectively over their
operating temperature ranges. To use a ceramic chip capacitor with Y5V dielectric, the value must be much higher than an
X7R ceramic capacitor to ensure the same minimum capacitance over the equivalent operating temperature range.
September 2004
11
M9999-091604
MIC37100/37101/37102
Micrel
Minimum Load Current
The MIC37100/01/02 regulator is specified between finite
loads. If the output current is too small, leakage currents
dominate and the output voltage rises. A 10mA minimum load
current is necessary for proper regulation.
Adjustable Regulator Design
VIN
MIC37102
OUT
IN
been used by MOSFET manufacturers for years, proving
very reliable and cost effective for the user.
Thermal resistance consists of two main elements, θJC
(junction-to-case thermal resistance) and θCA (case-to-ambient thermal resistance). See Figure 3. θJC is the resistance
from the die to the leads of the package. θCA is the resistance
from the leads to the ambient air and it includes θCS (case-tosink thermal resistance) and θSA (sink-to-ambient thermal
resistance).
VOUT
R1
ENABLE
SHUTDOWN
EN
ADJ
GND
R2
COUT
SOIC-8
 R1
VOUT = 1.240V 1 +

 R2 
Figure 2. Adjustable Regulator with Resistors
The MIC37102 allows programming the output voltage anywhere between 1.24V and the 6V maximum operating rating
of the family. Two resistors are used. Resistors can be quite
large, up to 1MΩ, because of the very high input impedance
and low bias current of the sense comparator: The resistor
values are calculated by:
θJA
θJC
θCA
ground plane
heat sink area
AMBIENT
printed circuit board
V

R1 = R2  OUT − 1
 1.240 
Figure 3. Thermal Resistance
Using the power SOIC-8 reduces the θJC dramatically and
allows the user to reduce θCA. The total thermal resistance,
θJA (junction-to-ambient thermal resistance) is the limiting
factor in calculating the maximum power dissipation capability of the device. Typically, the power SOIC-8 has a θJC of
20°C/W, this is significantly lower than the standard SOIC-8
which is typically 75°C/W. θCA is reduced because pins 5
through 8 can now be soldered directly to a ground plane
which significantly reduces the case-to-sink thermal resistance and sink to ambient thermal resistance.
Low-dropout linear regulators from Micrel are rated to a
maximum junction temperature of 125°C. It is important not
to exceed this maximum junction temperature during operation of the device. To prevent this maximum junction temperature from being exceeded, the appropriate ground plane heat
sink must be used.
Where VO is the desired output voltage. Figure 2 shows
component definition. Applications with widely varying load
currents may scale the resistors to draw the minimum load
current required for proper operation (see above).
Power SOIC-8 Thermal Characteristics
One of the secrets of the MIC37101/02’s performance is its
power SO-8 package featuring half the thermal resistance of
a standard SO-8 package. Lower thermal resistance means
more output current or higher input voltage for a given
package size.
Lower thermal resistance is achieved by joining the four
ground leads with the die attach paddle to create a singlepiece electrical and thermal conductor. This concept has
M9999-091604
12
September 2004
MIC37100/37101/37102
Micrel
Using Figure 4, the minimum amount of required copper can
be determined based on the required power dissipation.
Power dissipation in a linear regulator is calculated as follows:
PD = (VIN – VOUT) IOUT + VIN × IGND
If we use a 2.5V output device and a 3.3V input at an output
current of 1A, then our power dissipation is as follows:
PD = (3.3V – 2.5V) × 1A + 3.3V × 11mA
PD = 800mW + 36mW
700
∆TJA =
100°C
COPPER AREA (mm2)
800
40°C
50°C
55°C
65°C
75°C
85°C
900
600
500
400
300
200
100
0
0
0.25 0.50 0.75 1.00 1.25 1.50
POWER DISSIPATION (W)
PD = 836mW
From Figure 4, the minimum amount of copper required to
operate this application at a ∆T of 75°C is 160mm2.
Quick Method
Determine the power dissipation requirements for the design
along with the maximum ambient temperature at which the
device will be operated. Refer to Figure 5, which shows safe
operating curves for three different ambient temperatures:
25°C, 50°C and 85°C. From these curves, the minimum
amount of copper can be determined by knowing the maximum power dissipation required. If the maximum ambient
temperature is 50°C and the power dissipation is as above,
836mW, the curve in Figure 5 shows that the required area of
copper is 160mm2.
The θJA of this package is ideally 63°C/W, but it will vary
depending upon the availability of copper ground plane to
which it is attached.
Figure 4. Copper Area vs. Power SO-8
Power Dissipation
Figure 4 shows copper area versus power dissipation with
each trace corresponding to a different temperature rise
above ambient.
From these curves, the minimum area of copper necessary
for the part to operate safely can be determined. The maximum allowable temperature rise must be calculated to determine operation along which curve.
∆T = TJ(max) – TA(max)
TJ(max) = 125°C
TA(max) = maximum ambient operating temperature
For example, the maximum ambient temperature is 50°C, the
∆T is determined as follows:
∆T = 125°C – 50°C
∆T = 75°C
COPPER AREA (mm2)
900
800
TJ = 125°C
700
TA = 85°C
50°C 25°C
600
500
400
300
200
100
0
0
0.25 0.50 0.75 1.00 1.25 1.50
POWER DISSIPATION (W)
Figure 5. Copper Area vs. Power-SOIC
Power Dissipation
September 2004
13
M9999-091604
MIC37100/37101/37102
Micrel
Package Information
3.15 (0.124)
2.90 (0.114)
CL
3.71 (0.146) 7.49 (0.295)
3.30 (0.130) 6.71 (0.264)
CL
2.41 (0.095)
2.21 (0.087)
1.04 (0.041)
0.85 (0.033)
4.7 (0.185)
4.5 (0.177)
0.10 (0.004)
0.02 (0.0008)
DIMENSIONS:
MM (INCH)
6.70 (0.264)
6.30 (0.248)
1.70 (0.067)
16°
1.52 (0.060)
10°
10°
MAX
0.38 (0.015)
0.25 (0.010)
0.84 (0.033)
0.64 (0.025)
0.91 (0.036) MIN
SOT-223 (S)
0.026 (0.65)
MAX)
PIN 1
0.157 (3.99)
0.150 (3.81)
DIMENSIONS:
INCHES (MM)
0.050 (1.27)
TYP
0.064 (1.63)
0.045 (1.14)
0.197 (5.0)
0.189 (4.8)
0.020 (0.51)
0.013 (0.33)
0.0098 (0.249)
0.0040 (0.102)
0°–8°
SEATING
PLANE
45°
0.010 (0.25)
0.007 (0.18)
0.050 (1.27)
0.016 (0.40)
0.244 (6.20)
0.228 (5.79)
8-Lead SOIC (M)
M9999-091604
14
September 2004
MIC37100/37101/37102
Micrel
DIMENSIONS:
INCH (MM)
0.375 (9.52)
0.365 (9.27)
0.360 (9.14)
0.350 (8.89)
0.050 (1.27)
0.030 (0.76)
0.080 (2.03)
0.070 (1.78)
0.256 BSC
(6.50 BSC)
0.010 BSC
(0.25 BSC)
0.045 (1.14)
0.035 (0.89)
0.316 BSC
(8.03 BSC)
0.420 (10.67)
0.410 (10.41)
0.320 (8.13)
0.310 (7.87)
0.067 BSC
(1.70 BSC)
0.031 (0.79)
0.025 (0.63)
0.005 (0.13)
0.001 (0.03)
0.080 (2.03)
0.070 (1.78)
0.031 (0.89)
0.041 (1.14)
0.010 BSC
(0.25 BSC)
6¡
0¡
5 Lead S-PAK (R)
MICREL, INC.
TEL
1849 FORTUNE DRIVE SAN JOSE, CA 95131
+ 1 (408) 944-0800
FAX
+ 1 (408) 474-1000
WEB
USA
http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its
use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical
implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user.
A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to
fully indemnify Micrel for any damages resulting from such use or sale.
© 2004 Micrel, Incorporated.
September 2004
15
M9999-091604