Diodes AP7365-18SNG-7 600ma, low quiescent current, fast transient low dropout linear regulator Datasheet

AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Description
Pin Assignments
NEW PRODUCT
The AP7365 is a 600mA, adjustable and fixed output voltage,
low dropout linear regulator. The device included pass
element, error amplifier, band-gap, current limit and thermal
shutdown circuitry. The device is turned on when EN pin is
set to logic high level.
The characteristics of low dropout voltage and low quiescent
current make it suitable for low power applications, for
example, battery powered devices. The typical quiescent
current is approximately 35μA. Built-in current-limit and
thermal-shutdown functions prevent IC from damage in fault
conditions.
This device is available with adjustable output from 0.8V to
5.0V, and fixed version with 0.8V, 1.0V, 1.2V, 1.5V, 1.8V,
2.0V, 2.5V, 2.8V, 3.0V, 3.3V and 3.9V outputs. Please
contact your local sales office for any other voltage options.
(Top View)
(Top View)
IN 1
5 OUT
IN 1
5 OUT
GND 2
GND 2
4 NC
EN 3
EN 3
4 ADJ
SOT25 (Fixed output)
SOT25 (Adj output)
(Top View)
(Top View)
EN 1
6 NC
EN 1
GND 2
5 NC
GND 2
The AP7365 is available in SOT25, SOT89/R-3L, SOT223/R3L, and DFN2020-6 packages.
IN 3
4 OUT
DFN2020-6 (Fixed output)
6 ADJ
5 NC
IN 3
4 OUT
DFN2020-6 (Adj output)
Features
(Top View)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
600mA Low Dropout Regulator with EN
Very low IQ: 35µA
Wide input voltage range: 2V to 6V
Wide adjustable output: 0.8V to 5.0V
Fixed output options: 0.8V to 3.9V (0.1V step size
possible)
High PSRR: 65dB at 1kHz
Fast start-up time: 200µs
Stable with low ESR, 1µF ceramic output capacitor
Excellent Load/Line Transient Response
Low dropout: 300mV at 600mA
Current limit and short circuit protection
Thermal shutdown protection
Ambient temperature range: -40ºC to 85ºC
SOT25, SOT89/R-3L, SOT223/R-3L, DFN2020-6:
Available in “Green” Molding Compound (No Br, Sb)
Lead Free Finish/ RoHS Compliant (Note 1)
(Top View)
3
IN
3
OUT
2
GND (TAB)
2
IN (TAB)
1
OUT
1
GND
SOT89-3L (Fixed output)
SOT89R-3L (Fixed output)
(Top View)
(Top View)
3
IN
3
OUT
2
GND (TAB)
2
IN (TAB)
1
OUT
1
GND
SOT223-3L (Fixed output)
SOT223R-3L (Fixed output)
Applications
•
•
•
•
Servers and notebook computers
Low and medium power applications
FPGA and DSP core or I/O power
Consumer Electronics
Notes:
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
AP7365
Document number: DS32260 Rev. 1 - 2
1 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Application Circuit
V IN
1uF
ADJ
EN
G ND
OUT
AP7365
R1
1uF
Enable
V OUT
IN
OUT
AP7365
1uF
NEW PRODUCT
V IN
V OUT
IN
Enable
1uF
EN
GND
R2
Fixed Output
Adjustable Output
⎛
R ⎞
VOUT = VREF ⎜⎜1 + 1 ⎟⎟ where R 2 ≤ 80KΩ
R2 ⎠
⎝
Pin Descriptions
Pin
Name
Pin Number
DFN2020-6 DFN2020-6
(fixed)
(adj)
SOT25
(fixed)
SOT25
(adj)
IN
1
1
3
GND
EN
ADJ
NC
2
3
4
2
3
4
-
OUT
5
5
AP7365
Document number: DS32260 Rev. 1 - 2
SOT89/
SOT223
SOT89R/
SOT223R
3
3
2
2
1
5, 6
2
1
6
5
2
-
1
-
4
4
1
3
2 of 21
www.diodes.com
Description
Voltage input pin. Bypass to
ground through at least 1µF
MLCC capacitor
Ground
Enable input, active high
Output feedback pin
No connection
Voltage output pin. Bypass
to ground through 1µF
MLCC capacitor
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Functional Block Diagram
IN
OUT
Gate
Driver
EN
Current Limit
and Thermal
Shutdown
OUT
IN
Gate
Driver
EN
R
Current Limit
and Thermal
Shutdown
NEW PRODUCT
ADJ
0.8V
0.8V
R
GND
GND
Adjustable Version
Fixed Version
Absolute Maximum Ratings
Symbol
ESD HBM
ESD MM
VIN
TST
TJ
Parameter
Human Body Model ESD Protection
Machine Model ESD Protection
Input Voltage
OUT, EN Voltage
Continuous Load Current per Channel
Storage Temperature Range
Maximum Junction Temperature
Ratings
2000
200
6.5
VIN + 0.3
Internal Limited
-65 to 150
150
Unit
V
V
V
V
°C
°C
Recommended Operating Conditions
Symbol
VIN
IOUT
TA
Notes:
Parameter
Input voltage
Output Current (Note 2)
Operating Ambient Temperature
Min
2
0
-40
Max
6
600
85
Unit
V
mA
°C
2 The device maintains a stable, regulated output voltage without a load current.
AP7365
Document number: DS32260 Rev. 1 - 2
3 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Electrical Characteristics
NEW PRODUCT
(TA = 25oC, VIN = VOUT +1V, CIN = 1μF, COUT = 1μF, VEN = 2V, unless otherwise stated)
Symbol
Parameter
Test Conditions
Min Typ. Max
ADJ Reference Voltage (Adjustable version) IOUT= 0mA
0.8
VREF
ADJ Leakage (Adjustable version)
0.1
1
IADJ
TA = -40oC to 85oC,
-2
2
VOUT Output Voltage Accuracy
IOUT = 10% of IOUT-Max
VIN = (VOUT +1V) to VIN-Max,
ΔVOUT
Line Regulation
0.02 0.20
VEN = VIN, IOUT = 1mA
/ΔVIN/V
VIN = (VOUT +1V) to VIN-Max,
ΔVOUT
Load Regulation
-1.0
1.0
IOUT = 1mA to 600mA
/VOUT
VOUT < 2.5V, IOUT = 600mA
370 600
VDropout Dropout Voltage (Note 3)
VOUT ≥ 2.5V, IOUT = 600mA
300 400
Input Quiescent Current
VEN = VIN, IOUT = 0mA
35
80
IQ
VEN = 0V, IOUT = 0mA
0.1
1
ISHDN Input Shutdown Current
Input Leakage Current
VEN = 0V, OUT grounded
0.1
1
ILEAK
VEN = 0V to 2.0V in 1μs,
200
Start-up Time
tST
IOUT = 600mA
VIN = [VOUT +1V]VDC + 0.5VppAC,
65
PSRR PSRR (Note 4)
f = 1kHz, IOUT = 50mA
VIN = VIN-Min to VIN-Max,
240
VOUT < 0.2V (fixed version) or
ISHORT Short-circuit Current
25% of VOUT (ADJ version)
VIN = VIN-Min to VIN-Max,
0.8 1.4
Current limit
ILIMIT
VOUT/ROUT = 2.5A
EN Input Logic Low Voltage
VIN = VIN-Min to VIN-Max
0.4
VIL
EN Input Logic High Voltage
VIN = VIN-Min to VIN-Max
1.4
VIH
EN Input Current
VIN = 0V or VIN-Max
-1
1
IEN
145
TSHDN Thermal shutdown threshold
Thermal shutdown hysteresis
15
THYS
SOT25 (Note 5)
187
DFN2020-6 (Note 5)
251
Thermal Resistance Junction-to-Ambient
θJA
SOT89-3L (Note 5)
141
SOT223-3L (Note 5)
153
Notes:
Unit
V
μA
%
%/V
%
mV
μA
μA
μA
μs
dB
mA
A
V
V
μA
°C
°C
o
C/W
3. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal
value.
4. At VIN < 2.3V, the PSRR performance may be reduced.
5. Test condition for all packages: Device mounted on FR-4 substrate PC board, 1oz copper, with minimum recommended pad
layout.
AP7365
Document number: DS32260 Rev. 1 - 2
4 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Performance Characteristics
Start-Up Time
Start-Up Time
NEW PRODUCT
VEN=0 to 2V (1V/div)
VIN=5V
CIN=COUT=1μF
VOUT=3.3V (1V/div)
with no load
VEN=0 to 2V (1V/div)
VIN=5V
CIN=COUT=1μF
VOUT=3.3V (1V/div)
with 600mA load
Time (40μs/div)
Time (40μs/div)
Line Transient Response
Line Transient Response
VIN=4.3V to 5.3V (1V/div)
Tr=Tf=2μs
CIN=none, COUT=1μF
VIN=4.3V to 5.3V (1V/div)
Tr=Tf=2μs
CIN=none, COUT=1μF
VOUT=3.3V (20mV/div)
VOUT=3.3V (20mV/div)
IOUT=60mA (200mA/div)
IOUT=300mA(200mA/div)
Time (40μs/div)
AP7365
Document number: DS32260 Rev. 1 - 2
Time (40μs/div)
5 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Performance Characteristics (Continued)
Load Transient Response
Load Transient Response
VOUT=1.8V (200mV/div)
VOUT=1.8V (200mV/div)
NEW PRODUCT
VIN=VEN=2.8V
CIN=COUT=1μF
Tr=Tf=1μs
VIN=VEN=2.8V
CIN=COUT=1μF
Tr=Tf=1μs
IOUT=10mA to 300mA (500mA/div)
IOUT=10mA to 600mA (500mA/div)
Time (100μs/div)
Time (100μs/div)
Load Transient Response
Load Transient Response
VOUT=3.3V (200mV/div)
VOUT=3.3V (200mV/div)
VIN=VEN=4.3V
CIN=COUT=1μF
Tr=Tf=1μs
VIN=VEN=4.3V
CIN=COUT=1μF
Tr=Tf=1μs
IOUT=10mA to 300mA (500mA/div)
IOUT=10mA to 600mA (500mA/div)
Time (100μs/div)
AP7365
Document number: DS32260 Rev. 1 - 2
Time (100μs/div)
6 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Performance Characteristics (Continued)
PSRR
PSRR
80
80
IOUT=50mA
70
60
IOUT=300mA
50
40
PSRR(dB)
PSRR(dB)
60
VIN=2.25V+0.5VppAC
VOUT=0.8V
CIN=none, COUT=1μF
TA=25°C
30
20
IOUT=300mA
50
40
VIN=2.25V+0.5VppAC
VOUT=1.2V
CIN=none, COUT=1μF
TA=25°C
30
20
10
10
0
0
0.1
1
10
Frequency(kHz)
0.1
100
PSRR
1
10
Frequency(kHz)
100
PSRR
80
80
IOUT=50mA
70
IOUT=50mA
70
60
50
PSRR(dB)
60
PSRR(dB)
NEW PRODUCT
IOUT=50mA
70
IOUT=300mA
40
VIN=2.8V+0.5VppAC
VOUT=1.8V
CIN=none, COUT=1μF
TA=25°C
30
20
50
20
10
0
0
1
10
Frequency(kHz)
AP7365
Document number: DS32260 Rev. 1 - 2
VIN=4.3V+0.5VppAC
VOUT=3.3V
CIN=none, COUT=1μF
TA=25°C
30
10
0.1
IOUT=300mA
40
100
7 of 21
www.diodes.com
0.1
1
10
Frequency(kHz)
100
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Performance Characteristics (Continued)
Input Quiescent Current vs Temperature
Input Quiescent current vs Input Voltage
60
Input Quiescent Current(μA)
Input Quiescent current(μA)
TA=25°C
VOUT=3.3V
IOUT=0mA
50
40
30
20
10
VIN=VEN=4.3V
VOUT=3.3V
IOUT=0mA
50
40
30
20
10
0
0
4
4.5
5
5.5
Input Voltage(V)
-50
6
-25
0
25
50
75
Temperature(℃ )
100
125
Line Regulation
Load Regulation
0.08
0.1
-45°C
0.0
25°C
Output Variation(%/V)
Output Variation(%)
NEW PRODUCT
60
-0.1
90°C
-0.2
-0.3
90°C
0.04
0.00
25°C
-0.04
VOUT=3.3V
IOUT=1mA
VIN=VEN=4.3V
VOUT=3.3V
-0.4
-0.5
-45°C
-0.08
0
100
200
300
400
Output Current(mA)
AP7365
Document number: DS32260 Rev. 1 - 2
500
600
8 of 21
www.diodes.com
4
4.5
5
5.5
Input Voltage(V)
6
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Performance Characteristics (Continued)
Dropout Voltage vs Output Current
Dropout Voltage vs Output Current
500
600
VOUT=3.3V
VOUT=1.8V
Dropout Voltage(mV)
Dropout Voltage(mV)
90°C
400
25°C
300
200
100
400
90°C
300
25°C
200
-45°C
100
-45°C
0
0
0
100
200
300
400
Output Current(mA)
500
0
600
100
200
300
400
Output Current(mA)
500
600
Short-circuit Current vs Temperature
ADJ Reference Voltage vs Temperature
0.82
500
VIN=4.3V
VIN=4.3V
IOUT=0mA
0.81
Short-circuit Current(mA)
ADJ Reference Voltage(V)
NEW PRODUCT
500
0.80
0.79
400
300
200
100
0
0.78
-50
-25
0
25
50
75
Temperature(℃ )
AP7365
Document number: DS32260 Rev. 1 - 2
100
125
9 of 21
www.diodes.com
-50
-25
0
25
50
75
Temperature(℃ )
100
125
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Typical Performance Characteristics (Continued)
Current limit vs Temperature
2.0
Current limit(A)
NEW PRODUCT
1.6
1.2
0.8
0.4
VIN=4.3V
VOUT=3.3V
0.0
-50
-25
0
25
50
75
Temperature(℃)
AP7365
Document number: DS32260 Rev. 1 - 2
100
125
10 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Application Note
Output Capacitor
The output capacitor is required to stabilize and improve the transient response of the LDO. The AP7365 is stable
with very small ceramic output capacitors. Using a ceramic capacitor value that is at least 1μF with ESR > 15mΩ
on the output ensures stability. Higher capacitance values help to improve line and load transient response. The
output capacitance may be increased to keep low undershoot and overshoot. Output capacitor must be placed as
close as possible to OUT and GND pins.
Region of Stable COUT ESR vs. Load Current
100
Unstable Range
10
COUT ESR (Ω)
NEW PRODUCT
Input Capacitor
A 1μF ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and
noise. The amount of the capacitance may be increased without limit. This input capacitor must be located as
close as possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is
required for both IN and GND pins. A lower ESR capacitor type allows the use of less capacitance, while higher
ESR type requires more capacitance.
1
VIN=4.3V
CIN=COUT=1μF
Stable Range
0.1
0.01
Unstable Range
0.001
0
100
200
300
400
500
600
Load Current (mA)
AP7365
Document number: DS32260 Rev. 1 - 2
11 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Application Note (Continued)
Adjustable Operation
The AP7365 provides output voltage from 0.8V to 5.0V through external resistor divider as shown below.
V IN
V OUT
IN
OUT
A P 736 5
NEW PRODUCT
1uF
E nab le
R1
1 uF
ADJ
EN
GND
R2
The output voltage is calculated by:
⎛
R ⎞
VOUT = VREF ⎜⎜1 + 1 ⎟⎟
⎝ R2 ⎠
Where VREF=0.8V (the internal reference voltage)
Rearranging the equation will give the following that is used for adjusting the output to a particular voltage:
⎞
⎛V
R1 = R2 ⎜⎜ OUT − 1⎟⎟
V
⎠
⎝ REF
To maintain the stability of the internal reference voltage, R2 need to be kept smaller than 80kΩ.
No Load Stability
Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain
stable and regulated in no load condition.
ON/OFF Input Operation
The AP7365 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used,
the EN pin should be tied to IN pin to keep the regulator output on at all time. To ensure proper operation, the
signal source used to drive the EN pin must be able to swing above and below the specified turn-on/off voltage
thresholds listed in the Electrical Characteristics section under VIL and VIH.
Current Limit Protection
When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered
and clamp the output current to approximately 1.4A to prevent over-current and to protect the regulator from
damage due to overheating.
Short Circuit Protection
When OUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to
approximately 240mA. This feature protects the regulator from over-current and damage due to overheating.
AP7365
Document number: DS32260 Rev. 1 - 2
12 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Application Note (Continued)
NEW PRODUCT
Thermal Shutdown Protection
Thermal protection disables the output when the junction temperature rises to approximately +145°C, allowing the
device to cool down. When the junction temperature reduces to approximately +130°C the output circuitry is
enabled again. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal
protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it from
damage due to overheating.
Ultra Fast Start-up
After enabled, the AP7365 is able to provide full power in as little as hundreds of microseconds, typically 200µs,
without sacrificing low ground current. This feature will help load circuitry move in and out of standby mode in real
time, eventually extend battery life for mobile phones and other portable devices.
Fast Transient Response
Fast transient response LDO can extend battery life. TDMA-based cell phone protocols such as Global System for
Mobile Communications (GSM) have a transmit/receive duty factor of only 12.5 percent, enabling power savings
by putting much of the baseband circuitry into standby mode in between transmit cycles. In baseband circuits, the
load often transitions virtually instantaneously from 100µA to 100mA. To meet this load requirement, the LDO
must react very quickly without a large voltage drop or overshoot — a requirement that cannot be met with
conventional, general-purpose LDO.
The AP7365’s fast transient response from 0 to 600mA provides stable voltage supply for fast DSP and GSM
chipset with fast changing load.
Low Quiescent Current
The AP7365, consuming only around 35µA for all input range, provides great power saving in portable and low
power applications.
Wide Output Range
The AP7365, with a wide output range of 0.8V to 5.0V, provides a versatile LDO solution for many portable
applications.
Power Dissipation
The device power dissipation and proper sizing of the thermal plane that is connected to the thermal pad is critical
to avoid thermal shutdown and ensure reliable operation. Power dissipation of the device depends on input
voltage and load conditions and can be calculated by:
PD = (VIN - VOUT) X IOUT
The maximum power dissipation, handled by the device, depends on the maximum junction to ambient thermal
resistance, maximum ambient temperature, and maximum device junction temperature, which can be calculated
by the equation in the following:
PD (max@TA) =
AP7365
Document number: DS32260 Rev. 1 - 2
( +145°C - TA )
R θJA
13 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Ordering Information
NEW PRODUCT
AP7365 - XX XX G - X
Output
Package
Green
Packing
Blank : ADJ (Note 6)
08 : 0.8V
10 : 1.0V
12 : 1.2V
15 : 1.5V
18 : 1.8V
20 : 2.0V
25 : 2.5V
28 : 2.8V
30 : 3.0V
33 : 3.3V
39 : 3.9V
W : SOT25
SN : DFN2020-6
Y : SOT89-3L
YR : SOT89R-3L
E : SOT223-3L
ER : SOT223R-3L
G : Green
7/13 : Tape & Reel
Device
AP7365-XXWG-7
AP7365-XXSNG-7
AP7365-XXYG-13
AP7365-XXYRG-13
AP7365-XXEG-13
AP7365-XXERG-13
Notes:
Package
Code
W
SN
Y
YR
E
ER
Packaging
(Note 7)
SOT25
DFN2020-6
SOT89-3L
SOT89R-3L
SOT223-3L
SOT223R-3L
7”/13” Tape and Reel
Quantity
Part Number Suffix
3000/Tape & Reel
-7
3000/Tape & Reel
-7
2500/Tape & Reel
-13
2500/Tape & Reel
-13
2500/Tape & Reel
-13
2500/Tape & Reel
-13
6. Adjustable version is only available in SOT25 and DFN2020-6 package.
7. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
AP7365
Document number: DS32260 Rev. 1 - 2
14 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Marking Information
(1) SOT25
7
( Top View )
5
4
XX Y W X
NEW PRODUCT
1
2
Device
AP7365-ADJ
AP7365-08
AP7365-10
AP7365-12
AP7365-15
AP7365-18
AP7365-20
AP7365-25
AP7365-28
AP7365-30
AP7365-33
AP7365-39
3
XX : Identification code
Y : Year 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
Package
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
SOT25
Identification Code
VA
VB
VC
VD
VE
VF
VG
VH
VJ
VK
VM
VN
(2) DFN2020-6
( Top View )
XX
Y WX
Device
AP7365-ADJ
AP7365-08
AP7365-10
AP7365-12
AP7365-15
AP7365-18
AP7365-20
AP7365-25
AP7365-28
AP7365-30
AP7365-33
AP7365-39
AP7365
Document number: DS32260 Rev. 1 - 2
XX : Identification Code
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
Package
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
DFN2020-6
15 of 21
www.diodes.com
Identification Code
VA
VB
VC
VD
VE
VF
VG
VH
VJ
VK
VM
VN
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Marking Information (Continued)
(3) SOT89-3L and SOT89R-3L
( Top View )
NEW PRODUCT
XX
Y W X
1
2
Device
AP7365-08
AP7365-10
AP7365-12
AP7365-15
AP7365-18
AP7365-20
AP7365-25
AP7365-28
AP7365-30
AP7365-33
AP7365-39
AP7365-08
AP7365-10
AP7365-12
AP7365-15
AP7365-18
AP7365-20
AP7365-25
AP7365-28
AP7365-30
AP7365-33
AP7365-39
AP7365
Document number: DS32260 Rev. 1 - 2
3
XX : Identification code
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z represents 52 and 53 week
X : Internal code
A~Z : Green
Package
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
SOT89R-3L
16 of 21
www.diodes.com
Identification Code
VB
VC
VD
VE
VF
VG
VH
VJ
VK
VM
VN
TB
TC
TD
TE
TF
TG
TH
TJ
TK
TM
TN
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Marking Information (Continued)
(4) SOT223-3L
( Top View )
Logo
NEW PRODUCT
Part Number
65-VV:08 for 0.8V
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V
YWX
6 5-VV
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z repersents 52 and 53 week
X : Internal code
A~Z : Green
(5) SOT223R-3L
( Top View )
Logo
Part Number
65R-VV : 08 for 0.8V
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V
AP7365
Document number: DS32260 Rev. 1 - 2
YWX
6 5 R -VV
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z repersents 52 and 53 week
X : Internal code
A~Z : Green
17 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Package Outline Dimensions (Continued)
NEW PRODUCT
(1) Package Type: SOT25
0.57/0.63
(2) Package Type: DFN2020-6
Marking
0.15max.
0.05 C
0.15 C
B
Seating plane
C
Top View
0.65
0.37
1.95/2.075
1.45/1.65
0.15
2x
0/0.05
0.08 C
A
0.15 C
0.65nom.
CL
0.2/0.3
Document number: DS32260 Rev. 1 - 2
0.37
0.9
1.67
0.05 M C A B
Bottom View
AP7365
CL
0.15
0.30/0.40
CL
1
R0.
2x-
0.76/0.96
1.95/2.075
Pin#1 ID
0.45
CL
18 of 21
www.diodes.com
Land Pattern Recommendation
(Unit:mm)
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Package Outline Dimensions (Continued)
(3) Package Type: SOT89-3L and SOT89R-3L
1.40/1.75
Typ 1.60
2.7
3.94/4.25
1.45/1.55
Typ 1.50
1.3
1.9
0.4
0.80/
1.20
NEW PRODUCT
2.35/2.60 Typ 2.48
1.7
1.5
0.9
Land Pattern Recommendation (Unit: mm)
2.90/3.10
Typ 3.00
50 (2x)
80 (2x)
1.40/1.60
Typ 1.50
4.40/4.60 Typ 4.50
0.36/0.48 0.41/0.53 0.36/0.48
Typ 0.42 Typ 0.47 Typ 0.42
0.35/0.43
Typ 0.39
(4) Package Type: SOT223-3L and SOT223R-3L
AP7365
Document number: DS32260 Rev. 1 - 2
19 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
Taping Orientation (Note 8)
NEW PRODUCT
For DFN2020-6
Notes:
8. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf.
AP7365
Document number: DS32260 Rev. 1 - 2
20 of 21
www.diodes.com
July 2010
© Diodes Incorporated
AP7365
600mA, Low Quiescent Current, Fast Transient
Low Dropout Linear Regulator
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
NEW PRODUCT
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other
changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability
arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any
license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described
herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized
sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall
indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names
and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without
the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided
in the labeling can be reasonably expected to result in significant injury to the user.
B.
A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or
systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems,
notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further,
Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes
Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2010, Diodes Incorporated
www.diodes.com
AP7365
Document number: DS32260 Rev. 1 - 2
21 of 21
www.diodes.com
July 2010
© Diodes Incorporated
Similar pages