LINER LT6002 Single, dual and quad, 1.8v, 13a precision rail-to-rail op amp Datasheet

LT6000/LT6001/LT6002
Single, Dual and Quad,
1.8V, 13µA Precision
Rail-to-Rail Op Amps
U
FEATURES
DESCRIPTIO
■
The LT®6000/LT6001/LT6002 are single, dual and quad
precision rail-to-rail input and output operational amplifiers. Designed to maximize battery life in always-on applications, the devices will operate on supplies down to 1.8V
while drawing only 13µA quiescient current. The low
supply current and low voltage operation is combined with
precision specifications; input offset is guaranteed less
than 600µV. The performance on 1.8V supplies is fully
specified and guaranteed over temperature. A shutdown
feature available in the LT6000 and the 10-lead dual
LT6001 version can be used to extend battery life by
allowing the amplifiers to be switched off during periods
of inactivity.
■
■
■
■
■
Ideal for Battery-Powered Applications
– Low Voltage: 1.8V to 16V Operation
– Low Current: 16µA/Amplifier Max
– Small Packages: DFN, MSOP, SSOP
– Shutdown to 1.5µA Max (LT6000, LT6001DD)
Low Offset Voltage: 600µV Max
Rail-to-Rail Input and Output
Fully Specified on 1.8V and 5V Supplies
Operating Temperature Range: –40°C to 85°C
Single Available in DFN
Dual Available in MSOP and DFN
Quad Available in SSOP and DFN
U
APPLICATIO S
■
■
■
■
■
The LT6000 is available in a tiny, dual fine pitch leadless
DFN package. The LT6001 is available in the 8-pin MSOP
package; a 10-lead version with the shutdown feature is
available in DFN package. The quad LT6002 is available in
the 16-pin SSOP package and the 16-pin DFN package.
These devices are specified over the commercial and
industrial temperature range.
Gas Sensing
Portable Instrumentation
Battery- or Solar-Powered Systems
Low Voltage Signal Processing
Micropower Active Filters
, LTC and LT are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
U
TYPICAL APPLICATIO
Micropower Oxygen Sensor
OXYGEN SENSOR
CITY TECHNOLOGY
40X(2)
25
–
330Ω
1/2 LT6001
+
+
VOUT = 1V IN AIR,
0V WITHOUT OXYGEN
330Ω
+VE
www.citytech.com
–
VS
–
VS
200k
1/2 LT6001
+
VS = 1.8V
ISUPPLY = 145µA IN AIR,
45µA WITHOUT OXYGEN
SUPPLY CURRENT PER AMPLIFIER (µA)
10k
100Ω
–VE
Start-Up Characteristics
Supply Current vs Supply Voltage
AV = 1
VCM = 0.5V
20
TA = 125°C
15
TA = 25°C
10
TA = –55°C
5
0
0.4 0.6
20k
60012 TA01a
0.8 1.0 1.2 1.4 1.6 1.8
TOTAL SUPPLY VOLTAGE (V)
2.0
60012 TA01b
600012fa
1
LT6000/LT6001/LT6002
W W
U
W
ABSOLUTE
AXI U RATI GS (Note 1)
Total Supply Voltage (V+ to V–) .............................. 18V
Input Current ..................................................... ±10mA
SHDN Pin Voltage (Note 7) ............................... V– to V+
Output Short Current Duration (Note 2) ......... Indefinite
Operating Temperature Range (Note 3) ... –40°C to 85°C
Specified Temperature Range (Note 4) .... –40°C to 85°C
Junction Temperature ........................................... 150°C
Junction Temperature (DFN Packages) ................ 125°C
Storage Temperature Range .................. –65°C to 150°C
Storage Temperature Range
DFN Packages ................................... –65°C to 125°C
Lead Temperature (Soldering, 10 sec)
MSOP, SSOP Packages .................................... 300°C
U
U
W
PACKAGE/ORDER I FOR ATIO
TOP VIEW
TOP VIEW
OUT A
IN– A
IN+ A
V–
5 V–
7
–IN 2
4 OUT
+IN 3
1
2
3
4
IN– A 2
8 V+
–
+
–
+
8 IN– B
11
V– 4
7 IN+ B
NC 5
6 SHDN
DD PACKAGE
10-LEAD (3mm ´ 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 250°C/W
TJMAX = 125°C, θJA = 160°C/W (NOTE 2)
9 OUT B
IN+ A 3
7 OUT B
6 IN– B
5 IN+ B
MS8 PACKAGE
8-LEAD PLASTIC MSOP
DCB PACKAGE
6-LEAD (2mm × 3mm) PLASTIC DFN
10 V+
OUT A 1
TOP VIEW
6 V+
SHDN 1
TJMAX = 125°C, θJA = 160°C/W (NOTE 2)
EXPOSED PAD (PIN 7) IS CONNECTED TO V– (PIN 5)
EXPOSED PAD (PIN 11) IS CONNECTED TO V– (PIN 4)
ORDER PART
NUMBER
DCB PART
MARKING*
ORDER PART
NUMBER
LT6000CDCB
LT6000IDCB
LCDM
LCDM
LT6001CMS8
LT6001IMS8
MS8 PART
MARKING*
ORDER PART
NUMBER
DD PART
MARKING*
LT6001CDD
LT6001IDD
LBVH
LBVH
LTBVD
LTBVD
TOP VIEW
TOP VIEW
OUT A
1
IN– A
2
IN+ A
3
V+
4
IN+ B
5
IN– B
6
OUT B
7
10 OUT C
NC
8
9
16 OUT D
–
+A
–
– 15 IN D
D+
14 IN+ D
13 V –
+
–B
+
+ 12 IN C
C–
11 IN– C
NC
OUT A
1
IN– A
2
IN+ A
3
V+
4
+
5
IN B
IN–
16 OUT D
A
D
15 IN– D
14 IN+ D
13 V –
17
12 IN+ C
B
C
11 IN– C
B
6
OUT B
7
10 OUT C
NC
8
9
NC
DHC PACKAGE
16-LEAD (5mm ´ 3mm) DFN
GN PACKAGE
16-LEAD NARROW PLASTIC SSOP
TJMAX = 125°C, θJA = 160°C/W (NOTE 2)
TJMAX = 150°C, θJA = 135°C/W
EXPOSED PAD (PIN 17) IS CONNECTED TO V– (PIN 13)
ORDER PART NUMBER
GN PART MARKING
ORDER PART NUMBER
DHC PART MARKING*
LT6002CGN
LT6002IGN
6002
6002I
LT6002CDHC
LT6002IDHC
6002
6002
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
*Temperature grades are identified on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges.
600012fa
2
LT6000/LT6001/LT6002
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full specified temperature
range, otherwise specifications are TA = 25°C. VS = 1.8V, 0V, VCM = VOUT = 0.5V. For the LT6000 and the LT6001DD, VSHDN = V+,
unless otherwise noted.
SYMBOL
VOS
PARAMETER
Input Offset Voltage
CONDITIONS
LT6001MS8
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
LT6000DCB, LT6001DD, LT6002GN
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
LT6002DHC
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
VCM = V+
LT6001MS8
MIN
TYP
200
MAX
600
800
950
750
1000
1200
900
1100
1300
UNITS
µV
µV
µV
µV
µV
µV
µV
µV
µV
400
1000
1300
µV
µV
500
1200
1550
µV
µV
500
1300
1700
5
µV
µV
µV/°C
nA
nA
nA
nA
nA
nA
µVP-P
nV/√Hz
fA/√Hz
GΩ
MΩ
pF
dB
dB
dB
V
dB
●
●
250
●
●
300
●
●
●
VCM = V+
LT6000DCB, LT6001DD, LT6002GN
●
VCM = V+
LT6002DHC
●
∆VOS/∆T
IB
Input Offset Voltage Drift (Note 5)
Input Bias Current
IOS
Input Offset Current
en
in
RIN
Input Noise Voltage
Input Voltage Noise Density
Input Current Noise Density
Input Resistance
CIN
CMRR
Input Capacitance
Common Mode Rejection Ratio
PSRR
Input Voltage Range
Power Supply Rejection Ratio
AVOL
Minimum Supply
Large-Signal Gain
VOL
VOH
Output Swing Low (Note 6)
Output Swing High (Note 6)
VCM = 0.5V
VCM = 0.5V
VCM = V–
VCM = V+
VCM = 0.5V
VCM = V–
VCM = V+
0.1Hz to 10Hz
f = 1kHz
f = 1kHz
Common Mode (VCM = 0V to 0.6V)
Differential
●
VCM = 0V to 0.6V, 0°C ≤ TA ≤ 70°C
VCM = 0.1V to 0.6V, –40°C ≤ TA ≤ 85°C
VCM = 0V to 1.8V
●
●
●
●
●
●
●
●
●
10
●
82
82
60
0
86
●
1.8
●
VS = 1.8V to 16V
VCM = VO = 0.5V
VCM = VO = 0.5V
VO = 0.25V to 1.25V
RL = 100k to GND
RL = 100k to GND
RL = 10k to GND
RL = 10k to GND
Input Overdrive = 30mV
No Load
ISINK = 100µA
Input Overdrive = 30mV
No Load
ISOURCE = 100µA
RL = 10k to GND
–5
–5
●
●
25
20
40
25
2
–2
–2
4
0.2
0.2
0.4
1.2
75
25
3.5
25
5
96
96
78
10
1
1
2
1.8
100
V
65
V/mV
V/mV
V/mV
V/mV
125
●
●
30
120
60
200
mV
mV
●
●
●
30
140
160
60
225
250
mV
mV
mV
600012fa
3
LT6000/LT6001/LT6002
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full specified temperature
range, otherwise specifications are TA = 25°C. VS = 1.8V, 0V, VCM = VOUT = 0.5V. For the LT6000 and the LT6001DD, VSHDN = V+,
unless otherwise noted.
SYMBOL
ISC
PARAMETER
Short-Circuit Current
IS
Supply Current per Amplifier
ISHDN
Total Supply Current in Shutdown (Note 7)
SHDN Pin Current (Note 7)
VL
VH
tON
Shutdown Output Leakage Current (Note 7)
SHDN Pin Input Low Voltage (Note 7)
SHDN Pin Input High Voltage (Note 7)
Turn On Time (Note 7)
tOFF
Turn Off Time (Note 7)
GBW
Gain Bandwidth Product (Note 8)
SR
FPBW
Slew Rate
Full Power Bandwidth (Note 9)
CONDITIONS
Short to GND
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
Short to V+
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
VSHDN = 0.3V
VSHDN = 1.8V
VSHDN = 0V
VSHDN = 0.3V (V– ≤ VOUT ≤ V+)
●
●
●
●
MIN
2
1
0.4
0.7
0.4
0.15
TYP
4
400
UNITS
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
nA
nA
nA
V
V
µs
100
µs
50
kHz
kHz
kHz
V/ms
V/ms
V/ms
kHz
2
13
●
●
●
●
●
–300
●
0.8
0
–200
20
●
●
VSHDN = 0V to 1.8V,
RL = 10k
VSHDN = 1.8V to 0V,
RL = 10k
Freq = 1kHz
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
AV = –1, VOUT = 0.25V to 1.5V
Measure 0.5V to 1.25V, 0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
VOUT = 1.25VP-P
●
●
●
●
MAX
16
22
24
1.5
30
0.3
1.5V
32
28
24
9
7
5
2.3
15
3.8
600012fa
4
LT6000/LT6001/LT6002
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full specified temperature
range, otherwise specifications are TA = 25°C. VS = 5V, 0V, VCM = VOUT = 1/2 Supply. For the LT6000 and the LT6001DD, VSHDN = V+,
unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Offset Voltage
LT6001MS8
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
LT6000DCB, LT6001DD, LT6002GN
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
LT6002DHC
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
VCM = V+
LT6001MS8
MIN
TYP
MAX
UNITS
200
600
800
950
750
1000
1200
900
1100
1300
µV
µV
µV
µV
µV
µV
µV
µV
µV
400
1000
1300
µV
µV
500
1200
1550
µV
µV
500
1300
1700
5
µV
µV
µV/°C
●
●
250
●
●
300
●
●
●
VCM = V+
LT6000DCB, LT6001DD, LT6002GN
●
VCM = V+
LT6002DHC
●
∆VOS/∆T
Input Offset Voltage Drift (Note 5)
VCM = VS/2
●
IB
Input Bias Current
VCM = VS/2
VCM = V–
VCM = V+
●
●
●
Input Offset Current
VCM = VS/2
VCM = V–
VCM = V+
●
●
●
Input Noise Voltage
0.1Hz to 10Hz
IOS
2
–6
–6
–2
–2
4
12
nA
nA
nA
0.2
0.2
0.4
1.2
1.2
2.4
nA
nA
nA
1.2
µVP-P
en
Input Voltage Noise Density
f = 1kHz
75
nV/√Hz
in
Input Current Noise Density
f = 1kHz
25
fA/√Hz
RIN
Input Resistance
Common Mode (VCM = 0V to 3.8V)
Differential
3.5
25
GΩ
MΩ
5
pF
105
105
86
dB
dB
dB
CIN
Input Capacitance
CMRR
Common Mode Rejection Ratio
VCM = 0V to 3.8V, 0°C ≤ TA ≤ 70°C
VCM = 0.1V to 3.8V, –40°C ≤ TA ≤ 85°C
VCM = 0V to 5V
Input Voltage Range
PSRR
Power Supply Rejection Ratio
VS = 1.8V to 16V
VCM = VO = 0.5V
Minimum Supply
AVOL
VOL
Large-Signal Gain
Output Swing Low (Note 6)
VO = 0.5V to 4.5V
RL = 100k to VS/2
RL = 100k to VS/2
RL = 10k to VS/2
RL = 10k to VS/2
RL = 10k to GND
RL = 10k to GND
Input Overdrive = 30mV
No Load
ISINK = 100µA
ISINK = 500µA
●
8.5
●
●
●
90
90
68
●
0
●
86
●
1.8
●
●
●
●
●
●
30
25
16
10
160
80
5
100
V
dB
V
60
V/mV
V/mV
V/mV
V/mV
V/mV
V/mV
25
1000
30
120
180
60
200
300
mV
mV
mV
600012fa
5
LT6000/LT6001/LT6002
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full specified temperature
range, otherwise specifications are TA = 25°C. VS = 5V, 0V, VCM = VOUT = 1/2 Supply. For the LT6000 and the LT6001DD, VSHDN = V+,
unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VOH
Output Swing High (Note 6)
Input Overdrive = 30mV
No Load
ISOURCE = 100µA
RL = 10k to GND
●
●
●
Short to GND
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
5
4
3
10
●
●
mA
mA
mA
Short to V+
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
3.5
2.5
1.5
7.5
●
●
mA
mA
mA
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
ISC
IS
Short-Circuit Current
Supply Current per Amplifier
MIN
VS = ±8V
ISHDN
TYP
MAX
UNITS
30
140
160
60
225
400
mV
mV
mV
15
18
24
27
µA
µA
µA
20
25
34
µA
µA
●
Total Supply Current in Shutdown (Note 7)
VSHDN = 0.3V
●
3
5
µA
SHDN Pin Current (Note 7)
VSHDN = 5V
VSHDN = 0V
●
●
0
–650
30
nA
nA
Shutdown Output Leakage Current (Note 7)
VSHDN = 0.3V (V– ≤ VOUT ≤ V+)
●
–1000
20
nA
VL
SHDN Pin Input Low Voltage (Note 7)
●
VH
SHDN Pin Input High Voltage (Note 7)
●
tON
Turn On Time (Note 7)
VSHDN = 0V to 5V, RL = 10k
400
µs
tOFF
Turn Off Time (Note 7)
VSHDN = 5V to 0V, RL = 10k
100
µs
GBW
Gain Bandwidth Product
Freq = 1kHz
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
40
35
30
60
●
●
kHz
kHz
kHz
AV = –1, VOUT = 0.5V to 4.5V
Measure 1V to 4V, 0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
11
8
6
18
●
●
V/ms
V/ms
V/ms
0.87
1.4
kHz
SR
FPBW
Slew Rate
Full Power Bandwidth (Note 9)
VOUT = 4VP-P
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: A heat sink may be required to keep the junction temperature
below the absolute maximum. This depends on the power supply voltage
and how many amplifiers are shorted. The θJA specified for the DD and
DHC packages is with minimal PCB heat spreading metal. Using expanded
metal area on all layers of a board reduces this value.
Note 3: The LT6000C/LT6000I/LT6001C/LT6001I and LT6002C/LT6002I
are guaranteed functional over the temperature range of –40°C to 85°C.
Note 4: The LT6000C/LT6001C/LT6002C is guaranteed to meet specified
performance from 0°C to 70°C. The LT6000C/LT6001C/LT6002C are
designed, characterized and expected to meet specified performance from
0.3
V
4.7
V
–40°C to 85°C but are not tested or QA sampled at these temperatures.
The LT6000I/LT6001I/ LT6002I is guaranteed to meet specified
performance from –40°C to 85°C.
Note 5: This parameter is not 100% tested.
Note 6: Output voltage swings are measured between the output and
power supply rails.
Note 7: Specifications apply to the LT6000 or the LT6001DD with
shutdown.
Note 8: Guaranteed by correlation to slew rate at VS = 1.8V and GBW at
VS = 5V.
Note 9: Full-power bandwidth is calculated from the slew rate:
FPBW = SR/πVP-P.
600012fa
6
LT6000/LT6001/LT6002
U W
TYPICAL PERFOR A CE CHARACTERISTICS
VOS Distribution
VS = 5V, 0V
VCM = 2.5V
MS8 PACKAGE
PERCENT OF UNITS (%)
25
PERCENT OF UNITS (%)
TC VOS Distribution
Supply Current vs Supply Voltage
20
20
15
10
35
VS = 5V, 0V
18 VCM = 2.5V
MS8, GN16,
16 DD10 PACKAGES
14 –40°C TO 85°C
SUPPLY CURRENT PER AMPLIFIER (µA)
30
12
10
8
6
4
5
2
0
–600
0
400
–400 –200
0
200
INPUT OFFSET VOLTAGE (µV)
600
–5 –4 –3 –2 –1 0 1 2 3
DISTRIBUTION (µV/°C)
4
Change in Input Offset Voltage
vs Total Supply Voltage
150
TA = 25°C
TA = 125°C
100
TA = 25°C
0
–100
TA = 25°C
0
TA = 125°C
5.0
TA = 25°C
TA = –55°C
–2.5
–5.0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
COMMON MODE VOLTAGE (V)
60012 G07
TA = –55°C
–200
2
4
6
8 10 12 14
TOTAL SUPPLY VOLTAGE (V)
16
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
INPUT COMMON MODE VOLTAGE (V)
18
Output Saturation Voltage
vs Load Current (Output Low)
1.0
VS = 5V, 0V
INPUT OVERDRIVE = 30mV
TA = 25°C
TA = 125°C
0.1
TA = –55°C
0.01
0.001
0.01
0.1
1
SOURCING LOAD CURRENT (mA)
5
60012 G06
OUTPUT LOW SATURATION VOLTAGE (V)
OUTPUT HIGH SATURATION VOLTAGE (V)
INPUT BIAS CURRENT (nA)
TA = 125°C
100
600012 G05
1.0
7.5
0
200
Output Saturation Voltage
vs Load Current (Output High)
10.0
18
VS = 5V, 0V
TYPICAL PART
–100
0
Input Bias Current
vs Common Mode Voltage
2.5
400
–300
3
VS = 5V, 0V
16
TA = –55°C
60012 G35
12.5
4
6
8 10 12 14
TOTAL SUPPLY VOLTAGE (V)
600012 G03
–100
2
1.5
2.5
TOTAL SUPPLY VOLTAGE (V)
2
Input Offset Voltage
vs Input Common Mode Voltage
TA = 125°C
TA = –55°C
1
TA = –55°C
5
300
200
–50
–100
10
0
OFFSET VOLTAGE (µV)
200
0
TA = 25°C
15
0
5
VCM = 0.5V
TYPICAL PART
300
OFFSET VOLTAGE (µV)
CHANGE IN OFFSET VOLTAGE (µV)
400
250
50
20
Input Offset Voltage
vs Total Supply Voltage
VCM = 0.5V
100
TA = 125°C
25
20012 G02
60012 G01
300
VCM = 0.5V
30
10
60012 G08
VS = 5V, 0V
INPUT OVERDRIVE = 30mV
TA = 25°C
TA = 125°C
0.1
0.01
0.001
TA = –55°C
0.01
0.1
1
SINKING LOAD CURRENT (mA)
10
60012 G08
600012fa
7
LT6000/LT6001/LT6002
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Saturation Voltage
vs Input Overdrive
90
80
70
60
50
40
OUTPUT HIGH
30
OUTPUT LOW
20
10
14
0
10
VCM = 0.5V
OUTPUT SHORTED TO V–
12
TA = 25°C
10
TA = 125°C
8
TA = –55°C
6
4
2
1
30
15
20
25
10
INPUT OVERDRIVE (mV)
2
3
TA = 25°C
4
TA = –55°C
2
0.1Hz to 10Hz Output Voltage Noise
VS = 5V, 0V
TA = 25°C
90
VCM = 4.5V
80
VCM = 2.5V
70
4 5 6 7
TIME (SECONDS)
8
9
50
10
20
RL = 10k
RL = 100k
–40
0.3
0.6
0.9
1.2
OUTPUT VOLTAGE (V)
1.5
1.8
60012 G16
10
100
FREQUENCY (Hz)
1000
60012 G15
Open-Loop Gain
200
40
CHANGE IN INPUT OFFSET VOLTAGE (µV)
40
0
1
Open-Loop Gain
VS = 1.8V, 0V
VCM = 0.5V
TA = 25°C
–20
VCM = 2.5V
60012 G14
Open-Loop Gain
60
VCM = 4.5V
100
1000
60012 G13
0
VS = 5V, 0V
TA = 25°C
10
10
100
FREQUENCY (Hz)
1
VS = 5V, 0V
VCM = 2.5V
TA = 25°C
CHANGE IN INPUT OFFSET VOLTAGE (µV)
3
20
RL = 10k
0
RL = 100k
–20
–40
5
Input Noise Current vs Frequency
INPUT NOISE CURRENT DENSITY (fA/√Hz)
NOISE VOLTAGE (nV/√Hz)
NOISE VOLTAGE (500nV/DIV)
2
3
2
4
TOTAL SUPPLY VOLTAGE (V)
1000
60
1
1
60012 G12
Noise Voltage Density vs Frequency
100
VS = ±2.5V
0
0
60012 G11
60012 G10
CHANGE IN INPUT OFFSET VOLTAGE (µV)
TA = 125°C
6
5
4
TOTAL SUPPLY VOLTAGE (V)
VCM = 0.5V
OUTPUT SHORTED TO V+
8
0
5
0
–60
OUTPUT SHORT-CIRCIUT CURRENT (mA)
VS = 5V, 0V
NO LOAD
OUTPUT SHORT-CIRCUIT CURRENT (mA)
OUTPUT SATURATION VOLTAGE (mV)
100
Output Short-Circuit Current vs
Total Supply Voltage (Sinking)
Output Short-Circuit Current vs
Total Supply Voltage (Sourcing)
0
1
3
4
2
OUTPUT VOLTAGE (V)
5
60012 G17
VS = ±2.5V
TA = 25°C
150
100
RL = 10k
50
0
RL = 100k
–50
–100
–150
– 200
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
OUTPUT VOLTAGE (V)
2
2.5
20012 G18
600012fa
8
LT6000/LT6001/LT6002
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Gain Bandwidth and Phase
Margin vs Temperature
80
VS = 5V, 0V
70
VCM = 2.5V
60
50
VS = 1.8V, 0V
40
VCM = 0.5V
30
GAIN BANDWIDTH
20
10
75 100
0
50
–50 –25
25
TEMPERATURE (°C)
AV = –1
RF = RG = 100k
30
25
120
60
50
RISING
VS = 5V, 0V
FALLING
VS = 1.8V, 0V
15
30
40
VCM = 2.5V
20
125
10
0
–20
GAIN
–10
50
25
75
0
TEMPERATURE (°C)
100
125
–30
0.1
1
–60
60012 G19
Capacitive Load Handling
Overshoot vs Capacitive Load
55
GAIN BANDWIDTH (kHz)
50
80
45
40
70
GAIN BANDWIDTH
60
100
COMMON MODE REJECTION RATIO (dB)
60
PHASE MARGIN
35
30
25
20
AV = 1
15
50
10
40
5
AV = 5
AV = 2
0
30
0
2
6
4
8 10 12 14 16
TOTAL SUPPLY VOLTAGE (V)
100
1000
CAPACITIVE LOAD (pF)
10
18
10000
90
30
NEGATIVE SUPPLY
40
1000
VS = ±2.5V
TA = 25°C
AV = 10
100
AV = 1
10
1
10
1
10
FREQUENCY (kHz)
50
100
60012 G25
1
10
FREQUENCY (kHz)
0.1
0.01
0.1
1
10
FREQUENCY (kHz)
100
60012 G24
OUTPUT IMPEDANCE (kΩ)
OUTPUT IMPEDANCE (Ω)
POSITIVE SUPPLY
0.1
60
Disabled Output Impedance
vs Frequency (LT6000/LT6001DD)
1000
50
–10
0.01
70
Output Impedance vs Frequency
VS = ±2.5V
TA = 25°C
70
80
60012 G23
Power Supply Rejection Ratio
vs Frequency
110
VS = ±2.5V
TA = 25°C
90
30
0.1
10000
600012 G36
COMMON MODE REJECTION RATIO (dB)
Common Mode Rejection Ratio
vs Frequency
50
VS = 5V, 0V
45 VCM = 2.5V
OVERSHOOT (%)
65
PHASE MARGIN (DEG)
70
–80
1000
10
100
FREQUENCY (kHz)
60012 G22
RF = RG = 100k
AV = –1
f = 1kHz
–40
VS = 5V, 0V
RF = RG = 100k
AV = –1
60012 G21
Gain Bandwidth and Phase
Margin vs Supply Voltage
20
VCM = 4.5V
–20
5
–50 –25
60
VCM = 4.5V
0
FALLING
VS = 5V, 0V
10
80
VCM = 2.5V
40
RISING
VS = 1.8V, 0V
20
100
PHASE
PHASE (DEG)
VS = 5V, 0V
VCM = 2.5V
70
GAIN (dB)
VS = 1.8V, 0V
VCM = 0.5V
35
SLEW RATE (V/ms)
PHASE MARGIN
PHASE MARGIN (DEG)
f = 1kHz
GAIN BANDWIDTH (kHz)
Gain and Phase vs Frequency
Slew Rate vs Temperature
80
75
70
65
60
55
50
45
100
60012 G26
VS = ±2.5V
VPIN6(SHDN) = –2.5V
100
10
1
0
0.01
0.1
1
10
FREQUENCY (kHz)
100
60012 G27
600012fa
9
LT6000/LT6001/LT6002
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Large-Signal Response
Large-Signal Response
Small-Signal Response
4.5V
1.5V
20mV/DIV
0.25V
0.5V
AV = 1
VS = 5V, 0V
CL = 100pF
RL = 10k
60012 G28
100µs/DIV
AV = 1
VS = 1.8V, 0V
CL = 100pF
RL = 10k
SUPPLY CURRENT BOTH AMPLIFIERS (µA)
TA = 125°C
40
30
TA = 25°C
TA = –55°C
20
10
SUPPLY CURRENT BOTH AMPLIFIERS (µA)
60
VS = 1.8V, 0V
AV = 1
VS = ±2.5V
CL = 100pF
RL = 100k
Total Supply Current
vs SHDN Pin Voltage (LT6001DD)
Total Supply Current
vs SHDN Pin Voltage (LT6001DD)
50
60012 G29
100µs/DIV
Shutdown Response
(LT6000/LT6001DD)
TA = 125°C
VSHDN
40
TA = 25°C
0V
TA = –55°C
VOUT
30
20
0V
10
0
–5 –4 –3 –2 –1 0 1 2 3
SHDN PIN VOLTAGE (V)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
SHDN PIN VOLTAGE (V)
5
500µs/DIV
60012 G33
Supply Current
vs SHDN Pin Voltage (LT6000)
Supply Current
vs SHDN Pin Voltage (LT6000)
30
VS = 1.8V, 0V
VS = ±5V
TA = 125°C
25
25
TA = 125°C
SUPPLY CURRENT (µA)
SUPPLY CURRENT (µA)
4
VIN = 1V
AV = 1
VS = 1.8V, 0V
RL = 100k
60012 G32
60012 G31
30
60012 G30
VS = ±5V
50
0
0
10µs/DIV
20
TA = 25°C
15
10
TA = –55°C
20
TA = 25°C
15
TA = –55°C
10
5
5
0
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
SHDN PIN VOLTAGE (V)
60012 G37
–5 –4 –3 –2 –1 0 1 2 3
SHDN PIN VOLTAGE (V)
4
5
60012 G34
600012fa
10
LT6000/LT6001/LT6002
W
W
SI PLIFIED SCHE ATIC
V+
R4
Q17
Q16
R5
Q2
Q1
Q14
R8
7M
CM
Q10
R1
Q11
V+
V–
Q7
R2
30k
IN+
SHDN
Q3
Q4
Q5
C1
Q6
COMPLEMENTARY
DRIVE GENERATOR
+
V
IN–
Q18 Q19
R3 D3
30k
Q12
Q20 Q8
Q9
R6
Q13
OUT
V–
Q15
R7
V–
Figure 1
U
W
U U
APPLICATIO S I FOR ATIO
Supply Voltage
The positive supply of the LT6000/LT6001/LT6002 should
be bypassed with a small capacitor (about 0.01µF) within
an inch of the pin. When driving heavy loads, an additional
4.7µF electrolytic capacitor should be used. When using
split supplies, the same is true for the negative supply pin.
Rail-to-Rail Characteristics
The LT6000/LT6001/LT6002 are fully functional for an
input signal range from the negative supply to the positive
supply. Figure 1 shows a simplified schematic of the
amplifier. The input stage consists of two differential
amplifiers, a PNP stage Q3/Q6 and an NPN stage Q4/Q5
that are active over different ranges of the input common
mode voltage. The PNP stage is active for common mode
voltages, VCM, between the negative supply to approximately 1V below the positive supply. As VCM moves closer
towards the positive supply, the transistor Q7 will steer
Q2’s tail current to the current mirror Q8/Q9, activating the
NPN differential pair. The PNP pair becomes inactive for
the rest of the input common mode range up to the
positive supply.
The second stage is a folded cascode and current mirror
that converts the input stage differential signals into a
single ended output. Capacitor C1 reduces the unity cross
frequency and improves the frequency stability without
degrading the gain bandwidth of the amplifier. The complementary drive generator supplies current to the output
transistors that swing from rail to rail.
Input
The input bias current depends on which stage is active.
The input bias current polarity depends on the input
common mode voltage. When the PNP stage is active, the
input bias currents flow out of the input pins. They flow in
the opposite direction when the NPN stage is active. The
offset error due to the input bias currents can be
minimized by equalizing the noninverting and inverting
source impedance.
600012fa
11
LT6000/LT6001/LT6002
U
W
U U
APPLICATIO S I FOR ATIO
Start-Up and Output Saturation Characteristics
The input offset voltage changes depending on which
input stage is active; input offset voltage is trimmed on
both input stages, and is guaranteed to be 600µV max in
the PNP stage. By trimming the input offset voltage of
both input stages, the input offset voltage over the entire
common mode range (CMRR) is typically 400µV, maintaining the precision characteristics of the amplifier.
Micropower op amps are often not micropower during
start-up characteristics or during output saturation. This
can wreak havoc on limited current supplies, in the worst
case there may not be enough supply current available to
take the system up to nominal voltages. Also, when the
output saturates, the part may draw excessive current and
pull down the supplies, compromising rail-to-rail performance. Figure 1 shows the start-up characteristics of the
LT6000/LT6001/LT6002 for three limiting cases. The circuits are shown in Figure 2. One circuit creates a positive
offset forcing the output to come up saturated high.
Another circuit creates a negative offset forcing the output
to come up saturated low, while the last circuit brings the
output up at 1/2 supply. In all cases, the supply current is
well controlled and is not excessive when the output is on
either rail.
The input stage of the LT6000/LT6001/LT6002 incorporates phase reversal protection to prevent wrong polarity
outputs from occurring when the inputs are driven up to
2V below the negative rail. 30k protective resistors are
included in the input leads so that current does not
become excessive when the inputs are forced below V– or
when a large differential signal is applied. Input current
should be limited to 10mA when the inputs are driven
above the positive rail.
Output
20
SUPPLY CURRENT PER AMPLIFIER (µA)
The output of the LT6000/LT6001/LT6002 can swing to
within 30mV of the positive rail with no load and within
30mV of the negative rail with no load. When monitoring
input voltages within 30mV of the positive rail or within
30mV of the negative rail, gain should be taken to keep
the output from clipping. The LT6000/LT6001/LT6002
can typically source 10mA on a single 5V supply, sourcing current is reduced to 4mA on a single 1.8V supply as
noted in the electrical characteristics.
OUTPUT AT VS/2
14
12
OUTPUT HIGH
10
8
6
4
2
0
0.5
1
+
4.5
5
Figure 1. Start-Up Characteristics
+
30mV
1.5 2 2.5 3 3.5 4
SUPPLY VOLTAGE (V)
60012 F01
VS
VS
–
OUTPUT LOW
16
0
The normally reverse-biased substrate diode from the
output to V– will cause unlimited currents to flow when the
output is forced below V–. If the current is transient and
limited to 100mA, no damage will occur.
30mV
18
VS
+
VS/2
–
–
60012 F02
Output High
Output Low
Output at VS/2
Figure 2. Circuits for Start-Up Characteristics
600012fa
12
LT6000/LT6001/LT6002
U
W
U U
APPLICATIO S I FOR ATIO
The LT6000/LT6001/LT6002 outputs can swing to within
a respectable 30mV of each rail and draw virtually no
excessive supply current. Figure 3 compares the dual
LT6001 to a competitive part. Both op amps are in unity
gain and their outputs are driven into each rail. The supply
current is shown when the op amps are in linear operation
and when they are driven into each rail. As can be seen
from Figure 3, the supply current of the competitive part
increases 3-fold or 5-fold depending on which rail the
output goes to whereas the LT6001 draws virtually no
excessive current.
VOUT (V)
COMPETITIVE
PART
LT6001
4
3
2
1
0
–1
–2
–3
VIN
+
–
SUPPLY CURRENT
PER AMPLIFIER
VOUT
–3
–2
–1
0
VIN (V)
1
2
3
ICC (µA)
70
60
50
40
30
20
10
VS = ±2.5V, AV = 1
Gain
The open-loop gain is almost independent of load when
the output is sourcing current. This optimizes performance in single supply applications where the load is
returned to ground. The typical performance curve of
Open-Loop Gain for various loads shows the details.
Shutdown
The single LT6000 and the 10-lead dual LT6001 include a
shutdown feature that disables the part reducing quiescent current and makes the output high impedance. The
devices can be shut down by bringing the SHDN pin within
0.3V of V–. The amplifiers are guaranteed to shut down if
the SHDN pin is brought within 0.3V of V–. The exact
switchover point will be a function of the supply voltage.
See the Typical Performance Characteristics curves Supply Current vs Shutdown Pin Voltage. When shut down the
total supply current is about 0.8µA and the output leakage
current is 20nA (V– ≤ VOUT ≤ V+). For normal operation the
SHDN pin should be tied to V+. It can be left floating,
however, parasitic leakage currents over 1µA at the SHDN
pin may inadvertently place the part into shutdown.
60012 F03
Figure 3. VOUT and ICC vs Input Voltage
600012fa
13
LT6000/LT6001/LT6002
U
TYPICAL APPLICATIO
Gain of 100 Amplifier
(400kHz GBW on 30µA Supply)
0.9V
(NiMH)
3
VIN
8
+
1
1/2 LT6001
2
5
–
+
7
1/2 LT6001
6
–0.9V
(NiMH)
90.9k
OUT
–
90.9k
60012 TA02a
10k
10k
Gain vs Frequency
60
50
40
GAIN (dB)
30
20
10
0
–10
–20
–30
–40
100
1k
10k
100k
FREQUENCY (Hz)
1M
60012 TA02b
600012fa
14
LT6000/LT6001/LT6002
U
PACKAGE DESCRIPTIO
DCB Package
6-Lead Plastic DFN (2mm × 3mm)
(Reference LTC DWG # 05-08-1715)
0.70 ±0.05
3.55 ±0.05
1.65 ±0.05
(2 SIDES)
2.15 ±0.05
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
1.35 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
2.00 ±0.10
(2 SIDES)
R = 0.05
TYP
3.00 ±0.10
(2 SIDES)
0.40 ± 0.10
4
6
1.65 ± 0.10
(2 SIDES)
PIN 1 NOTCH
R0.20 OR 0.25
× 45° CHAMFER
PIN 1 BAR
TOP MARK
(SEE NOTE 6)
3
0.200 REF
0.75 ±0.05
1
(DCB6) DFN 0405
0.25 ± 0.05
0.50 BSC
1.35 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (TBD)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
600012fa
15
LT6000/LT6001/LT6002
U
PACKAGE DESCRIPTIO
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660)
0.889 ± 0.127
(.035 ± .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
0.42 ± 0.038
(.0165 ± .0015)
TYP
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.65
(.0256)
BSC
8
7 6 5
0.52
(.0205)
REF
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
4.90 ± 0.152
(.193 ± .006)
DETAIL “A”
0° – 6° TYP
GAUGE PLANE
0.53 ± 0.152
(.021 ± .006)
DETAIL “A”
1
2 3
4
1.10
(.043)
MAX
0.86
(.034)
REF
0.18
(.007)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
0.65
(.0256)
NOTE:
BSC
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.127 ± 0.076
(.005 ± .003)
MSOP (MS8) 0204
600012fa
16
LT6000/LT6001/LT6002
U
PACKAGE DESCRIPTIO
DD Package
10-Lead (3mm × 3mm) Plastic DFN
(Reference LTC DWG # 05-08-1699)
0.675 ±0.05
3.50 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
6
3.00 ±0.10
(4 SIDES)
0.38 ± 0.10
10
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
(DD10) DFN 1103
5
0.200 REF
1
0.75 ±0.05
0.00 – 0.05
0.25 ± 0.05
0.50 BSC
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
600012fa
17
LT6000/LT6001/LT6002
U
PACKAGE DESCRIPTIO
GN Package
16-Lead Narrow Plastic SSOP
(Reference LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.045 ± .005
16 15 14 13 12 11 10 9
.254 MIN
.009
(0.229)
REF
.150 – .165
.229 – .244
(5.817 – 6.198)
.0165 ± .0015
.150 – .157**
(3.810 – 3.988)
.0250 BSC
RECOMMENDED SOLDER PAD LAYOUT
1
.015 ± .004
× 45°
(0.38 ± 0.10)
.007 – .0098
(0.178 – 0.249)
.0532 – .0688
(1.35 – 1.75)
2 3
4
5 6
7
8
.004 – .0098
(0.102 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
.008 – .012
(0.203 – 0.305)
TYP
.0250
(0.635)
BSC
GN16 (SSOP) 0204
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
600012fa
18
LT6000/LT6001/LT6002
U
PACKAGE DESCRIPTIO
DHC Package
16-Lead (5mm × 5mm) Plastic DFN
(Reference LTC DWG # 05-08-1706)
0.65 ±0.05
3.50 ±0.05
1.65 ±0.05
2.20 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
4.40 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
5.00 ±0.10
(2 SIDES)
R = 0.20
TYP
3.00 ±0.10
(2 SIDES)
9
0.40 ± 0.10
16
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
PIN 1
NOTCH
(DHC16) DFN 1103
8
0.200 REF
1
0.25 ± 0.05
0.50 BSC
0.75 ±0.05
4.40 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJED-1) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
600012fa
19
LT6000/LT6001/LT6002
U
TYPICAL APPLICATIO
Low Power V-to-F Converter
VREF
VREF
2M
2M
VREF
42.2k
1M
3
+
7
2M
1M
2
1M
3
8
®
–
LTC 1440
0.1µF
A2
1/2 LT6001
1
VOUT
6
5
2
TP0610
+
1M
–
1
42.2k
VREF
1000pF
VREF
5
VIN
6
+
DIODES:
CENTRAL SEMI
CMOD3003
×4
8
A1
1/2 LT6001
7
2N7002
–
0.1µF
4
VS
4.3V TO 20V
0.1µF
FREQUENCY OUT ≈ 7.5Hz/mV • VIN
LINEARITY ≈ 5%, VIN 20mV TO 800mV
ISUPPLY ≈ 60µA TO 100µA
6
4
LT1790-4.096
VREF
1µF
42.2k
60012 TA03
1
MUX Amplifier
2
MUX Amplifier Waveforms
1.8V
+
VIN1
–
LT6000
SHDN
VOUT
VOUT
1.8V
+
VIN2
–
LT6000
SHDN
INPUT
SELECT
VS = 1.8V
5ms/DIV
VIN1 = 250Hz AT 1VP-P
VIN2 = 500Hz AT 0.5VP-P
INPUT SELECT = 25Hz AT 1.8VP-P
60012 TA04a
INPUT
SELECT
SN74LVC2604
60012 TA04b
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT2178/LT2179
17µA Dual/Quad Single Supply Op Amps
®
120µV VOS(MAX), Gain Bandwidth = 60kHz
LT1490A/LT1491A
50µA Dual/Quad Over-The-Top Rail-to-Rail Input and Output Op Amps
950µV VOS(MAX), Gain Bandwidth = 200kHz
LT1494/LT1495/LT1496
1.5µA Max Single/Dual/Quad Over-The-Top Precision Rail-to-Rail Input
and Output Op Amps
375µV VOS(MAX), Gain Bandwidth = 2.7kHz
LT1672/LT1673/LT1674
2µA Max, AV ≥ 5, Single/Dual/Quad Over-The-Top Precision Rail-to-Rail
Input and Output Op Amps
Gain of 5 Stable, Gain Bandwidth = 12kHz
LT1782
Micropower, Over-The-Top SOT-23 Rail-to-Rail Input and Output Op Amps
SOT-23, 800µV VOS(MAX), IS = 55µA (Max),
Gain Bandwidth = 200kHz, Shutdown Pin
Over-The-Top is a registered trademark of Linear Technology Corporation.
600012fa
20
Linear Technology Corporation
LT 0406 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2005
Similar pages