GLENAIR M85049-38S11A Strain relief Datasheet

Strain
Reliefs
AS85049/38
Strain Relief
Glenair Connector
Designator H
MIL-DTL-38999
Series III & IV,
EN3645
M85049/38 S 11 W
Basic Part No.
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = 300 Series Steel, Passivated
W = Aluminum, 500 Hour Cadmium Olive Drab
Over Electroless Nickel
S = Self-Locking
Use Dash for Non-Self-Locking
Shell Size
A Thread
Cable
Entry
F
Self-Locking
Only
E
Self-Locking Only
H
Note: Screw orientation shown is for
non-self-locking configuration. Screws
on self-locking configurations are on
the same side/face of the clamp.
TABLE I
Shell
Shell Size
Size Ref.
9
A
11
B
13
C
15
D
17
E
19
F
G
21
23
H
25
J
A Thread
Class 2B
M12 X 1 - 6H
M15 X 1 - 6H
M18 X 1 - 6H
M22 X 1 - 6H
M25 X 1 - 6H
M28 X 1 - 6H
M31 X 1 - 6H
M34 X 1 - 6H
M37 X 1 - 6H
E Dia Max
Self-Locking
Only
.858 (21.8)
.984 (25.0)
1.157 (29.4)
1.279 (32.5)
1.406 (35.7)
1.516 (38.5)
1.642 (41.7)
1.768 (44.9)
1.889 (48.0)
F Max
Self-Locking
Only
.91 (23.1)
.91 (23.1)
1.01 (25.7)
1.06 (26.9)
1.16 (29.5)
1.41 (35.8)
1.51 (38.4)
1.66 (42.2)
1.76 (44.7)
H
Max
.85 (21.6)
.90 (22.9)
1.10 (27.9)
1.15 (29.2)
1.30 (33.0)
1.50 (38.1)
1.60 (40.6)
1.70 (43.2)
1.80 (45.7)
Cable Entry
Max
Min
.098 (2.5) .234 (5.9)
.153 (3.9) .234 (5.9)
.190 (4.8) .328 (8.3)
.260 (6.6) .457 (11.6)
.283 (7.2) .614 (15.6)
.325 (8.3) .634 (16.1)
.343 (8.7) .698 (17.7)
.381 (9.7) .823 (20.9)
.418 (10.6) .853 (21.7)
1. For complete dimensions see applicable Military Specification.
2. Metric dimensions (mm) are indicated in parentheses.
3. Cable Entry is defined as the accomodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
© 2005 Glenair, Inc.
CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
www.glenair.com
E-Mail: [email protected]
62-11
Similar pages