Delta DVSA283R3S-XXX High reliability hybrid dc-dc converter Datasheet

DVSA2800S Series
HIGH RELIABILITY HYBRID
DC-DC CONVERTERS
DESCRIPTION
FEATURES
The DVSA series of high reliability DC-DC converters
is operable over the full military (-55 °C to +125 °C)
temperature range with no power derating. Unique
to the DVSA series is a magnetic feedback circuit
that is radiation immune. Operating at a nominal
fixed frequency of 450 kHz, these regulated, isolated
units utilize well controlled undervoltage lockout
circuitry to eliminate slow start-up problems.
•
•
•
These converters are designed and manufactured in
a facility qualified to ISO9001 and certified to MILPRF-38534 and MIL-STD-883.
This product may incorporate one or more of the
following U.S. patents:
5,784,266
5,790,389
5,963,438
5,999,433
6,005,780
6,084,792
6,118,673
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
High Reliability
Very Low Output Noise
Wide Input Voltage Range: 15 to 50 Volts per
MIL-STD-704
Up to 6 Watts Output Power
Radiation Immune Magnetic Feedback Circuit
NO Use of Optoisolators
Undervoltage Lockout
Indefinite Short Circuit Protection
Current Limit Protection
Industry Standard Pinout
High Input Transient Voltage: 80 Volts for 1 sec
per MIL-STD-704A
Radiation Hardened Version Available
Precision Projection Welded Hermetic Package
High Power Density: > 19 W/in3
Custom Versions Available
Additional Environmental Screening Available
Meets MIL-STD-461C and MIL-STD-461D EMC
Requirements When Used With a DVMA28 EMI
Filter
MIL-PRF-38534 Element Evaluated
Components
Figure 1 – DVSA2800S DC-DC Converter
(Not To Scale)
1X001DSF
11314 4th Avenue
West, Suite 206
Everett, WA 98204
http://www.vpt-inc.com
Sales Information:
Phone: (425) 353-3010
Fax: (425) 353-4030
E-mail: [email protected]
1
DVSA2800S Series
SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified)
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Input Voltage (Transient, 1 second)
Output Power1
Power Dissipation (Full Load, TCASE = +125°C)
Parameter
50 VDC
80 Volts
6 Watts
2.7 Watts
Junction Temperature Rise to Case
Storage Temperature
Lead Solder Temperature (10 seconds)
Weight (Maximum)
DVSA283R3S
Conditions
Min
Typ
+10°C
-65°C to +150°C
270°C
15 Grams
DVSA2805S
Units
Max
Min
Typ
Max
STATIC
Continuous
INPUT
4
Voltage
Current
Ripple Current
Inhibit Pin Input
15
28
50
15
28
50
V
Transient, 1 sec
-
-
80
-
-
80
V
Inhibited
-
-
6
-
-
6
mA
No Load
-
-
60
-
-
60
mA
Full Load, 20Hz to 10MHz
-
-
50
-
-
50
mAp-p
4
Inhibit Pin Open Circuit Voltage
4
UVLO Turn On
4
UVLO Turn Off
OUTPUT
Voltage
1.5
0
-
1.5
V
13.0
9.0
11.0
13.0
V
12.0
-
14.8
12.0
-
14.8
V
V
11.0
-
14.5
11.0
-
14.5
TCASE = 25°C
3.267
3.30
3.333
4.95
5.00
5.05
V
VOUT
TCASE = -55°C to +125°C
3.25
3.30
3.35
4.925
5.00
5.075
V
0
-
4
0
-
5
W
3
Current
11.0
VOUT
Power
3
0
9.0
0
-
1.21
0
-
1.0
A
Ripple Voltage
VOUT
IOUT
Full Load, 20Hz to 10MHz
-
-
30
-
-
30
mVp-p
Line Regulation
VOUT
VIN = 15V to 50V
-
-
15
-
-
15
mV
Load Regulation
VOUT
No Load to Full Load
mV
EFFICIENCY
LOAD FAULT POWER DISSIPATION
Overload
4
Short Circuit
4
CAPACITIVE LOAD
SWITCHING FREQUENCY
ISOLATION
500 VDC
MTBF (MIL-HDBK-217F)
AIF @ TC = 55°C
-
-
50
-
-
50
62
66
-
65
70
-
%
-
-
3.3
-
-
3.3
W
-
-
3
-
-
3
W
-
-
1000
-
-
1000
µF
350
450
500
350
450
500
kHz
100
-
-
100
-
-
MΩ
-
457
-
-
457
-
kHrs
-
150
300
-
250
500
mVPK
DYNAMIC
Load Step Output Transient
VOUT
2
Load Step Recovery
Line Step Output Transient
4
VOUT
2, 4
Line Step Recovery
Turn On Delay
Turn On Overshoot
Notes:
VOUT
Half Load to Full Load
VIN = 16V to 40V
VIN = 0V to 28V
1. Dependant on output voltage.
3. Derate linearly to 0 at 135°C.
1X001DSF
-
450
700
-
450
700
µSec
-
250
500
-
350
700
mVPK
-
600
1200
-
600
1200
µSec
-
10
20
-
10
20
mSec
-
0
15
-
0
25
mVPK
2. Time for output voltage to settle within 1% of its nominal value.
4. Verified by qualification testing.
2
DVSA2800S Series
SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified)
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Input Voltage (Transient, 1 second)
Output Power1
Power Dissipation (Full Load, TCASE = +125°C)
Parameter
50 VDC
80 Volts
6 Watts
2.7 Watts
Junction Temperature Rise to Case
Storage Temperature
Lead Solder Temperature (10 seconds)
Weight (Maximum)
DVSA2812S
Conditions
Min
Typ
+10°C
-65°C to +150°C
270°C
15 Grams
DVSA2815S
Units
Max
Min
Typ
Max
STATIC
Continuous
INPUT
4
Voltage
Current
Ripple Current
Inhibit Pin Input
15
28
50
15
28
50
V
Transient, 1 sec
-
-
80
-
-
80
V
Inhibited
-
-
6
-
-
6
mA
No Load
-
-
60
-
-
60
mA
Full Load, 20Hz to 10MHz
-
-
50
-
-
50
mAp-p
4
Inhibit Pin Open Circuit Voltage
4
UVLO Turn On
4
UVLO Turn Off
OUTPUT
Voltage
1.5
0
-
1.5
V
13.0
9.0
11.0
13.0
V
12.0
-
14.8
12.0
-
14.8
V
V
11.0
-
14.5
11.0
-
14.5
TCASE = 25°C
11.88
12.0
12.12
14.85
15.0
15.15
V
VOUT
TCASE = -55°C to +125°C
11.82
12.0
12.18
14.775
15.0
15.225
V
0
-
6
0
-
6
W
3
Current
11.0
VOUT
Power
3
0
9.0
0
-
0.5
0
-
0.4
A
Ripple Voltage
VOUT
IOUT
Full Load, 20Hz to 10MHz
-
-
30
-
-
30
mVp-p
Line Regulation
VOUT
VIN = 15V to 50V
-
-
15
-
-
15
mV
Load Regulation
VOUT
No Load to Full Load
mV
EFFICIENCY
LOAD FAULT POWER DISSIPATION
Overload
4
Short Circuit
4
CAPACITIVE LOAD
SWITCHING FREQUENCY
ISOLATION
500 VDC
MTBF (MIL-HDBK-217F)
AIF @ TC = 55°C
-
-
50
-
-
50
71
75
-
72
76
-
%
-
-
3
-
-
3
W
-
-
3
-
-
3
W
-
-
500
-
-
500
µF
350
450
500
350
450
500
kHz
100
-
-
100
-
-
MΩ
-
457
-
-
457
-
kHrs
-
300
700
-
400
700
mVPK
DYNAMIC
Load Step Output Transient
VOUT
2
Load Step Recovery
Line Step Output Transient
4
VOUT
2, 4
Line Step Recovery
Turn On Delay
Turn On Overshoot
Notes:
VOUT
Half Load to Full Load
VIN = 16V to 40V
VIN = 0V to 28V
1. Dependant on output voltage.
3. Derate linearly to 0 at 135°C.
1X001DSF
-
200
400
-
200
400
µSec
-
700
1200
-
700
1300
mVPK
-
200
600
-
200
600
µSec
-
10
20
-
10
20
mSec
-
0
50
-
0
50
mVPK
2. Time for output voltage to settle within 1% of its nominal value.
4. Verified by qualification testing.
3
DVSA2800S Series
SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified)
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Input Voltage (Transient, 1 second)
Output Power1
Power Dissipation (Full Load, TCASE = +125°C)
Parameter
50 VDC
80 Volts
6 Watts
2.7 Watts
Junction Temperature Rise to Case
Storage Temperature
Lead Solder Temperature (10 seconds)
Weight (Maximum)
DVSA285R2S
Conditions
+10°C
-65°C to +150°C
270°C
15 Grams
Units
Min
Typ
Max
STATIC
Continuous
INPUT
4
Voltage
Current
Ripple Current
Inhibit Pin Input
15
28
50
V
Transient, 1 sec
-
-
80
V
Inhibited
-
-
6
mA
No Load
-
-
60
mA
Full Load, 20Hz to 10MHz
-
-
50
mAp-p
4
Inhibit Pin Open Circuit Voltage
4
UVLO Turn On
4
UVLO Turn Off
OUTPUT
Voltage
1.5
V
13.0
V
12.0
-
14.8
V
V
11.0
-
14.5
TCASE = 25°C
5.148
5.20
5.252
V
VOUT
TCASE = -55°C to +125°C
5.122
5.20
5.278
V
0
-
5.2
W
3
Current
11.0
VOUT
Power
3
0
9.0
0
-
1.0
A
Ripple Voltage
VOUT
IOUT
Full Load, 20Hz to 10MHz
-
-
30
mVp-p
Line Regulation
VOUT
VIN = 15V to 50V
-
-
15
mV
Load Regulation
VOUT
No Load to Full Load
mV
EFFICIENCY
LOAD FAULT POWER DISSIPATION
Overload
4
Short Circuit
4
CAPACITIVE LOAD
SWITCHING FREQUENCY
ISOLATION
500 VDC
MTBF (MIL-HDBK-217F)
AIF @ TC = 55°C
-
-
50
65
70
-
%
-
-
3.3
W
-
-
3
W
-
-
1000
µF
350
450
500
kHz
100
-
-
MΩ
-
457
-
kHrs
-
250
500
mVPK
DYNAMIC
Load Step Output Transient
VOUT
2
Load Step Recovery
Line Step Output Transient
4
VOUT
2, 4
Line Step Recovery
Turn On Delay
Turn On Overshoot
Notes:
VOUT
Half Load to Full Load
VIN = 16V to 40V
VIN = 0V to 28V
1. Dependant on output voltage.
3. Derate linearly to 0 at 135°C.
1X001DSF
-
450
700
µSec
-
350
700
mVPK
-
600
1200
µSec
-
10
20
mSec
-
0
25
mVPK
2. Time for output voltage to settle within 1% of its nominal value.
4. Verified by qualification testing.
4
DVSA2800S Series
BLOCK DIAGRAM
PIN 6
T1
PIN 1
D1
+V OUT
28V IN
L1
C2
C1
Rs2
OUT COM
IN COM
PIN 2
PIN 7
Q1
MAGNETIC
FEEDBACK
UNDER
VOLTAGE
SHUTDOWN
PRIMARY
HOUSEKEEPING
SUPPLY
VOLTAGE AND
CURRENT
AMPLIFIERS
Rs1
PWM
CONTROL
SECONDARY
HOUSEKEEPING
SUPPLY
INH
PIN 5
Figure 2
CONNECTION DIAGRAM
6
1
28V IN
28 Vdc
+
-
+V OUT
5
2
INH
LOAD
OUT COM
7
IN COM
Figure 3
1X001DSF
5
DVSA2800S Series
INHIBIT DRIVE CONNECTION DIAGRAMS
28V IN 6
28V IN 6
10K
INH
5
10K
OPTOISOLATOR
BIAS
OPTIONAL
CAPACITOR
INH
5
BIAS
OPTIONAL
CAPACITOR
12V
IN COM 7
12V
IN COM 7
Figure 4 – Internal Inhibit Circuit and Recommended Drive
Figure 5 – Isolated Inhibit Drive
(Shown with optional capacitor for turn-on delay)
(Shown with optional capacitor for turn-on delay)
EMI FILTER HOOKUP DIAGRAM
DVMA28 EMI FILTER
1
DVSA2800S DC-DC CONVERTER
2
28V IN
6
28V OUT
1
28V IN
+V OUT
LOAD
28 Vdc
5
+
5
4
OUT COM
7
IN COM OUT COM
3
INH
2
IN COM
CASE
8
Figure 6 – Converter with EMI Filter
1X001DSF
6
DVSA2800S Series
EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C, Full Load, Unless Otherwise Specified)
VIN = 28V
VIN = 40V
80
Efficiency (%)
70
60
50
40
5
4.5
4
3.5
3
2.5
2
Output Pow er (W)
Figure 7 – DVSA283R3S
Figure 8 – DVSA2805S / DVSA285R2S
Efficiency (%) vs. Output Power (W)
Efficiency (%) vs. Output Power (W)
90
80
80
70
Output Pow er (W)
Output Pow er (W)
Figure 9 – DVSA2812S
Figure 10 – DVSA2815S
Efficiency (%) vs. Output Power (W)
Efficiency (%) vs. Output Power (W)
1X001DSF
6
5.4
4.8
4.2
3.6
6
5.4
4.8
4.2
3.6
3
20
2.4
20
1.8
30
1.2
30
3
40
2.4
40
50
1.8
50
60
1.2
60
0.6
Efficiency (%)
70
0.6
Efficiency (%)
Output Pow er (W)
1.5
1
0.5
20
4
3.6
3.2
2.8
2.4
2
1.6
1.2
30
0.8
70
65
60
55
50
45
40
35
30
25
20
0.4
Efficiency (%)
VIN = 16V
7
DVSA2800S Series
EMI PERFORMANCE CURVES
(TCASE = 25°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified)
Figure 11 – DVSA2800S without EMI Filter
Figure 12 – DVSA2800S with EMI Filter
1X001DSF
8
DVSA2800S Series
PACKAGE SPECIFICATIONS
TOP VIEW
SIDE VIEW
PIN
FUNCTION
1
+V OUT
2
OUT COM
3
N/C
4
N/C
5
INHIBIT
6
28V IN
7
IN COM
8
CASE
BOTTOM VIEW
Figure 13 – Package and Pinout
(Dimensional Limits are ±0.005” Unless Otherwise Stated)
1X001DSF
9
DVSA2800S Series
PACKAGE PIN DESCRIPTION
Pin
Function
Description
1
+V OUT
Positive Output Voltage Connection
2
OUT COM
Output Common Connection
3
N/C
No Connection
4
N/C
No Connection
5
INHIBIT
Logic Low = Disabled Output. Connecting the inhibit pin to input common causes
converter shutdown.
Logic High = Enabled Output. Unconnected or open collector TTL.
6
28V IN
Positive Input Voltage Connection
7
IN COM
Input Common Connection
8
CASE
Case Connection
1X001DSF
10
DVSA2800S Series
ENVIRONMENTAL SCREENING (100% Tested Per MIL-STD-883 as referenced to MIL-PRF-38534)
Screening
MIL-STD-883
(No Suffix)
Extended
/ES
HB
/HB
Class H
/H
Class K
/K
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Standard
NonDestructive
Bond Pull
Method 2023
•
Internal
Visual
Method 2017, 2032
Internal Procedure
•
Temperature
Cycling
Method 1010, Condition C
Method 1010, -55°C to 125°C
•
Constant
Acceleration
Method 2001, 3000g, Y1 Direction
Method 2001, 500g, Y1 Direction
•
PIND
Method 2020, Condition A2
•
Pre Burn-In
Electrical
100% at 25°C
•
Burn-In
Method 1015, 320 hours at +125°C
Method 1015, 160 hours at +125°C
96 hours at +125°C
24 hours at +125°C
•
Final
Electrical
MIL-PRF-38534, Group A1
100% at 25°C
•
Hermeticity
Method 1014, Fine Leak, Condition A
Method 1014, Gross Leak, Condition C
-3
Dip (1 x 10 )
Radiography
Method 20123
External
Visual
Method 2009
Notes:
1X001DSF
1.
2.
3.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
100% R&R testing at –55°C, +25°C, and +125°C with all test data included in product shipment.
PIND test Certificate of Compliance included in product shipment.
Radiographic test Certificate of Compliance and film(s) included in product shipment.
11
DVSA2800S Series
ORDERING INFORMATION
DVSA
28
05
S
R
/HB
1
2
3
4
5
6
-
XXX
7
(1)
(2)
(3)
(4)
Product Series
Nominal Input
Voltage
Output Voltage
Number of Outputs
DVSA
28
1.
2.
3.
3R3
05
5R2
12
15
3.3 Volts
5 Volts
5.2 Volts
12 Volts
15 Volts
S
(5)
(6)
(7)
Rad-Hard Option2
Screening Code1,3
Additional Screening
Code
None
R
Notes:
28 Volts
Standard
100 kRad
None
/ES
/HB
/H
/K
Standard
Extended
HB
Class H
Class K
Single
Contact Sales
Contact the VPT Inc. Sales Department for availability of Class H (/H) or Class K (/K) qualified products.
VPT Inc. is not currently certified to a DSCC certified radiation hardness assurance program.
VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our
sole discretion unless specifically forbidden by customer contract.
Please contact your sales representative or the VPT Inc. Sales Department for more information
concerning additional environmental screening and testing, different input voltage, output voltage,
power requirement, source inspection, and/or special element evaluation for space or other higher
quality applications.
1X001DSF
12
DVSA2800S Series
SMD (STANDARD MICROCIRCUIT DRAWING) NUMBERS
Standard Microcircuit
Drawing (SMD)
DVSA2800S Series
Similar Part Number
5962-0324101HXC
DVSA283R3S/H
5962-0324102HXC
DVSA2805S/H
5962-0324103HXC
DVSA285R2S/H
5962-0324104HXC
DVSA2812S/H
5962-0324105HXC
DVSA2815S/H
Do not use the DVSA2800S Series similar part number for SMD product acquisition. It is listed for
reference only. For exact specifications for the SMD product, refer to the SMD drawing. SMD’s can be
downloaded from the DSCC website at http://www.dscc.dla.mil/programs/smcr/. The SMD number
listed above is for MIL-PRF-38534 Class H screening, standard gold plated lead finish, and no RHA
(Radiation Hardness Assurance) level. Please reference the SMD for other screening levels, lead
finishes, and radiation levels.
CONTACT INFORMATION
To request a quotation or place orders please contact your sales representative or the VPT Inc. Sales
Department at:
Phone:
Fax:
E-mail:
(425) 353-3010
(425) 353-4030
[email protected]
All information contained in this datasheet is believed to be accurate, however, no responsibility is assumed for possible errors
or omissions. The products or specifications contained herein are subject to change without notice.
1X001DSF
13
Similar pages