TI ADS62P22IRGCR Dual channel, 12-bits, 125/105/80/65 msps adc with ddr lvds/cmos output Datasheet

ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DUAL CHANNEL, 12-BITS, 125/105/80/65 MSPS ADC WITH DDR LVDS/CMOS OUTPUTS
•
FEATURES
1
•
•
•
•
•
•
•
•
•
•
•
Maximum Sample Rate: 125 MSPS
12-Bit Resolution with No Missing Codes
95 dB Crosstalk
Parallel CMOS and DDR LVDS Output Options
3.5 dB Coarse Gain and Programmable Fine
Gain up to 6 dB for SNR/SFDR Trade-Off
Digital Processing Block with:
– Offset Correction
– Fine Gain Correction, in Steps of 0.05 dB
– Decimation by 2/4/8
– Built-in and Custom Programmable 24-Tap
Low-/High-/Band-Pass Filters
Supports Sine, LVPECL, LVDS, and LVCMOS
Clocks and Amplitude Down to 400 mVPP
Clock Duty Cycle Stabilizer
Internal Reference; Supports External
Reference also
64-QFN Package (9mm × 9mm)
Pin Compatible 14-Bit Family (ADS62P4X)
APPLICATIONS
•
•
•
•
•
•
•
Wireless Communications Infrastructure
Software Defined Radio
Power Amplifier Linearization
802.16d/e
Test and Measurement Instrumentation
High Definition Video
Medical Imaging
Radar Systems
DESCRIPTION
ADS62P2X is a dual channel 12-bit A/D converter
family with maximum sample rates up to 125 MSPS.
It combines high performance and low power
consumption in a compact 64 QFN package. Using
an internal sample and hold and low jitter clock
buffer, the ADC supports high SNR and high SFDR at
high input frequencies. It has coarse and fine gain
options that can be used to improve SFDR
performance at lower full-scale input ranges.
ADS62P2X includes a digital processing block that
consists of several useful and commonly used digital
functions such as ADC offset correction, fine gain
correction (in steps of 0.05 dB), decimation by 2,4,8
and in-built and custom programmable filters. By
default, the digital processing block is bypassed, and
its functions are disabled.
Two output interface options exist – parallel CMOS
and DDR LVDS (Double Data Rate). ADS62P2X
includes internal references while traditional
reference pins and associated decoupling capacitors
have been eliminated. Nevertheless, the device can
also be driven with an external reference. The device
is specified over the industrial temperature range
(–40°C to 85°C).
ADS62P2X Performance Summary
SFDR, dBc
SINAD, dBFS
ADS62P25
ADS62P24
ADS62P23
ADS62P22
Fin = 10 MHz (0 dB gain)
88
92
93
94
Fin = 190 MHz (3.5 dB gain)
84
86
87
85
Fin = 10 MHz (0 dB gain)
Fin = 190 MHz (3.5 dB gain)
Analog power, mW
71
71.3
71.5
71.5
69.5
69.5
69.7
69.2
799
710
594
515
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2008, Texas Instruments Incorporated
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
DRGND
DRVDD
AGND
AVDD
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Digital Processing
Block
DA0
DA1
DA2
DA3
DA4
DA5
DA6
DA7
DA8
DA9
DA10
DA11
Channel A
INA_P
INA_M
SHA
CLKP
CLKM
12-Bit ADC
Output
Buffers
12 Bit
12 Bit
SHA
12-Bit ADC
Channel A
Output Clock
Buffer
CLOCKGEN
INB_P
INB_M
Digital
Encoder
Digital
Encoder
12 Bit
12 Bit
CLKOUT
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DB8
DB9
DB10
DB11
Output
Buffers
Channel B
Digital Processing
Block
Channel B
VCM
Reference
Control Interface
CTRL1
CTRL2
CTRL3
RESET
SCLK
SEN
SDAATA
CMOS Interface
B0286-02
ADS62PXX FAMILY
2
125 MSPS
105 MSPS
80 MSPS
65 MSPS
ADS62P4X
14 Bits
ADS62P45
ADS62P44
ADS62P43
ADS62P42
ADS62P2X
12 Bits
ADS62P25
ADS62P24
ADS62P23
ADS62P22
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
PACKAGE/ORDERING INFORMATION (1)
PRODUCT
PACKAGELEAD
PACKAGE
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ADS62P25
QFN-64 (2)
RGC
–40°C to 85°C
AZ62P25
ADS62P24
QFN-64 (2)
RGC
–40°C to 85°C
AZ62P24
ADS62P23
QFN-64 (2)
RGC
–40°C to 85°C
AZ62P23
ADS62P22
(1)
(2)
QFN-64 (2)
RGC
–40°C to 85°C
AZ62P22
ORDERING
NUMBER
TRANSPORT MEDIA,
QUANTITY
ADS62P25IRGCT
Tape and Reel, 250
ADS62P25IRGCR
Tape and Reel, 2500
ADS62P24IRGCT
Tape and Reel, 250
ADS62P24IRGCR
Tape and Reel, 2500
ADS62P23IRGCT
Tape and Reel, 250
ADS62P23IRGCR
Tape and Reel, 2500
ADS62P22IRGCT
Tape and Reel, 250
ADS62P22IRGCR
Tape and Reel, 2500
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
For thermal pad size on the package, see the mechanical drawings at the end of this data sheet. θJA = 23.17 °C/W (0 LFM air flow),
θJC = 22.1 °C/W when used with 2 oz. copper trace and pad soldered directly to a JEDEC standard four layer 3 in × 3 in (7.62 cm ×
7.62 cm) PCB.
ABSOLUTE MAXIMUM RATINGS (1)
VI
VALUE
UNIT
Supply voltage range, AVDD
–0.3 to 3.9
V
Supply voltage range, DRVDD
–0.3 to 3.9
V
Voltage between AGND and DRGND
–0.3 to 0.3
V
Voltage between AVDD to DRVDD
–0.3 to 3.3
V
–0.3 to 2
V
–0.3 to minimum ( 3.6, AVDD + 0.3)
V
Voltage applied to VCM pin (in external reference mode)
Voltage applied to analog input pins, INP and INM
Voltage applied to analog input pins, CLKP and CLKM
TA
Operating free-air temperature range
TJ
Operating junction temperature range
Tstg
Storage temperature range
(1)
–0.3 to (AVDD + 0.3)
V
–40 to 85
°C
125
°C
–65 to 150
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
3
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
3
3.3
3.6
V
1.65
1.8 to 3.3
3.6
V
3
3.3
3.6
V
SUPPLIES
AVDD
Analog supply voltage
(1)
DRVDD Output buffer supply voltage
CMOS interface
LVDS interface
ANALOG INPUTS
Differential input voltage range
VIC
2
Input common-mode voltage
Vpp
1.5 ± 0.1
Voltage applied on VCM in external reference mode
1.45
1.5
V
1.55
V
CLOCK INPUT
Input clock sample rate, FS
ADS62P25
1
125
ADS62P24
1
105
ADS62P23
1
80
ADS62P22
1
Sine wave, ac-coupled
Input clock amplitude differential
(VCLKP – VCLKM)
0.4
LVPECL, ac-coupled
65
1.5
± 0.8
LVDS, ac-coupled
Vpp
± 0.35
LVCMOS, ac-coupled
MSPS
3.3
Input Clock duty cycle
35%
50%
65%
DIGITAL OUTPUTS
Output buffer drive strength
(2)
for CLOAD ≤ 5 pF and DRVDD ≥ 2.2 V
DEFAULT
strength
for CLOAD > 5 pF and DRVDD ≥ 2.2 V
MAXIMUM
strength
for DRVDD < 2.2 V
MAXIMUM
strength
CMOS interface, maximum buffer
strength
CLOAD
Maximum external load capacitance from each
output pin to DRGND
10
LVDS interface, without internal
termination
5
LVDS interface, with internal
termination
RLOAD
Differential load resistance (external) between the LVDS output pairs
TA
Operating free-air temperature
(1)
(2)
4
pF
10
Ω
100
-40
85
°C
For easy migration to the next generation, higher sampling speed devices (> 125 MSPS), use 1.8 V DRVDD supply.
See Output Buffer Strength Programmability in application section
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
ELECTRICAL CHARACTERISTICS
Typical values are at 25°C, AVDD = 3.3 V, DRVDD = 1.8 V to 3.3 V, maximum rated sampling frequency, 50% clock duty
cycle, –1 dBFS differential analog input, internal reference mode, applies to CMOS and LVDS interfaces, unless otherwise
noted.
Min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD = 3.3 V, DRVDD = 3.3 V,
unless otherwise noted.
PARAMETER
ADS62P25
FS = 125 MSPS
ADS62P24
FS = 105 MSPS
MIN
MIN TYP
RESOLUTION
TYP
MA
X
MA
X
ADS62P23
FS = 80 MSPS
MIN
TYP
ADS62P22
FS = 65 MSPS
MA
X
MIN
TYP
MA
X
UNIT
12
12
12
12
Bits
2
2
2
2
VPP
>1
>1
>1
>1
MΩ
7
7
7
7
pF
Analog input bandwidth
450
450
450
450
MHz
Analog input common mode current (per input pin
of each ADC)
1.3
1.3
1.3
1.3
µA/MSPS
ANALOG INPUT
Differential input voltage range
Differential input resistance (dc)
see Figure 82
Differential input capacitance
see Figure 83
REFERENCE VOLTAGES
VREFB
Internal reference bottom voltage
1
1
1
1
V
VREFT
Internal reference top voltage
2
2
2
2
V
VCM
Common mode output voltage
1.5
1.5
1.5
1.5
4
4
4
4
VCM output current capability
V
mA
DC ACCURACY
No missing codes
EO
Specified
Offset error
-10
Offset error temperature coefficient
±2
Specified
10
-10
0.05
±2
10
Specified
-10
0.05
±2
Specified
10
-10
0.05
±2
10
0.05
mV
mV/°C
There are two sources of gain error – internal reference inaccuracy and channel gain error
EGREF
EGCHAN
Gain error due to internal reference inaccuracy
alone, (ΔVREF /2) %
-2
±0.25
2
-2
±0.2
5
2
-2
±0.25
2
-2
±0.25
2
% FS
-1
±0.3
1
-1 ±0.3
1
-1
±0.3
1
-1
±0.3
1
% FS
(1)
Gain error of channel alone
across devices & across channels within a device
Channel gain error temperature coefficient
DNL
Differential nonlinearity
INL
Integral nonlinearity
0.00
5
0.005
0.005
-0.75
±0.3
- ±0.3
0.75
-2
±0.6
2
-2 ±0.6
2
240
275
212
240
Δ%/°C
0.005
0.75
±0.3
-2
±0.6
2
177
200
0.75
±0.3
-2
±0.6
2
LSB
153
175
mA
LSB
POWER SUPPLY
IAVDD
Analog supply current
IDRVDD
Digital supply current,
CMOS interface
DRVDD = 1.8 V
FIN= 2 MHZ (2)
No external load
capacitance
15
13
11.5
10
mA
10 pF external
load capacitance
28
25
21
18
mA
73
73
73
73
mA
IDRVDD
Digital supply current, LVDS interface
DRVDD = 3.3 V
with 100 Ω external termination
PAVDD
Analog power dissipation
PDRVDD
Digital power dissipation
CMOS interface
DRVDD = 1.8 V (3)
799
(3)
710
792
594
660
515
578
mW
27
24
21
18
mW
10 pF external
load capacitance
51
45
38
32
mW
Global powerdown
(1)
(2)
908
No external load
capacitance
50
75
50
75
50
75
50
75
mW
This is specified by design and characterization; it is not tested in production.
In CMOS mode, the DRVDD current scales with the sampling frequency, load capacitance on output pins, input frequency and supply
voltage (see Figure 79 and CMOS power dissipation in the application section).
The maximum DRVDD current depends on the actual load capacitance on the digital output lines. Note that the maximum
recommended load capacitance is 10 pF.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
5
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
ELECTRICAL CHARACTERISTICS
Typical values are at 25°C, AVDD = 3.3 V, DRVDD = 1.8 V to 3.3 V, maximum rated sampling frequency, 50% clock duty
cycle, –1 dBFS differential analog input, internal reference mode, applies to CMOS and LVDS interfaces, unless otherwise
noted.
Min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD = 3.3 V, DRVDD = 3.3 V,
unless otherwise noted.
PARAMETER
TEST CONDITIONS
ADS62P25
FS = 125 MSPS
MIN
TYP
MAX
ADS62P24
FS = 105 MSPS
MIN
TYP
MAX
ADS62P23
FS = 80 MSPS
MIN
TYP
MAX
ADS62P22
FS = 65 MSPS
MIN
TYP
UNIT
MAX
DYNAMIC AC CHARACTERISTICS
Fin = 10 MHz
Fin = 50 MHz
SNR
Signal to Noise
Ratio
RMS Output
Noise
68.5
Fin = 70 MHz
Fin = 190
MHz
ENOB
Effective
Number of Bits
71.3
71.4
69
71.3
70.3
69.9
3.5 dB coarse
gain
69.5
69.5
69.7
69.2
Fin = 50 MHz
Fin = 70 MHz
Fin = 190
MHz
71
71.3
70.5
70.9
70.7
70.9
71.1
71.3
68.5
71.1
69.9
69.8
69.7
3.5 dB coarse
gain
69.2
69.3
69.5
69.4
11.0
11.4
11.1
11.0
76
92
80
83
76
11.1
93
79
89
87
79
89
81
83
83
81
3.5 dB coarse
gain
84
86
87
85
88
90
92
93
79
82
84.5
75
76
86
84
88
88
79
80
80
79
3.5 dB coarse
gain
81
82
82
82
94
93
95
98
92
93
Fin = 50 MHz
76
Fin = 70 MHz
92
76
79
94
93
94
96
86
86
85
86
3.5 dB coarse
gain
88
88
88
89
88
92
93
94
80
83
Fin = 50 MHz
76
Fin = 70 MHz
86
76
79
87
85
89
89
81
83
83
81
3.5 dB coarse
gain
84
86
87
85
Fin = 10 MHz
95
96
97
99
Fin = 50 MHz
94
95
96
98
Fin = 70 MHz
94
95
96
97
Fin = 190 MHz
90
93
95
92
Submit Documentation Feedback
dBc
87
79
0 dB gain
Fin = 190
MHz
dBc
97
79
0 dB gain
Fin = 10 MHz
dBc
86
77
0 dB gain
Fin = 10 MHz
Bits
94
87
85
11.5
0 dB gain
74
dBFS
11.6
11.5
88
86
Fin = 70 MHz
Fin = 190
MHz
71.5
71.3
69.6
Fin = 70 MHz
Fin = 190
MHz
68
71.5
68.5
0 dB gain
Fin = 50 MHz
dBFS
LSB
68
Fin = 50 MHz
6
71.2
70.2
Fin = 10 MHz
Worst Spur
(Other than
HD2, HD3)
71.6
71.4
Inputs tied to common-mode
SFDR
Fin = 70 MHz
Spurious Free
Dynamic Range
Fin = 190
MHz
HD3
Third Harmonic
Distortion
68.5
71.6
69
70.2
Fin = 50 MHz
HD2
Second
Harmonic
Distortion
71.3
0 dB gain
Fin = 10 MHz
THD
Total Harmonic
Distortion
71.5
71.1
71
Fin = 10 MHz
SINAD
Signal to Noise
and Distortion
Ratio
71.3
dBc
dBc
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
ELECTRICAL CHARACTERISTICS (continued)
Typical values are at 25°C, AVDD = 3.3 V, DRVDD = 1.8 V to 3.3 V, maximum rated sampling frequency, 50% clock duty
cycle, –1 dBFS differential analog input, internal reference mode, applies to CMOS and LVDS interfaces, unless otherwise
noted.
Min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD = 3.3 V, DRVDD = 3.3 V,
unless otherwise noted.
PARAMETER
ADS62P25
FS = 125 MSPS
TEST CONDITIONS
MIN
TYP
ADS62P24
FS = 105 MSPS
MAX
MIN
TYP
MAX
ADS62P23
FS = 80 MSPS
MIN
TYP
MAX
ADS62P22
FS = 65 MSPS
MIN
TYP
UNIT
MAX
IMD
2-Tone
Intermodulation
Distortion
F1 = 185 MHz, F2 = 190 MHz
each tone at -7 dBFS
88
87
92
92
dBFS
Crosstalk
Up to 100 MHz
95
95
95
95
dB
Input Overload
Recovery
Recovery to within 1% (of final
value) for 6-dB overload with sine
wave input
1
1
1
1
clock
cycles
PSRR
AC Power
Supply
Rejection Ratio
for 100 mVpp signal on AVDD
supply
35
35
35
35
dBc
DIGITAL CHARACTERISTICS (1)
The DC specifications refer to the condition where the digital outputs are not switching, but are permanently at a valid logic
level 0 or 1 AVDD = 3.0 V to 3.6 V.
PARAMETER
TEST CONDITIONS
ADS62P25/ADS62P24
ADS62P23/ADS62P22
MIN
TYP
MAX
UNIT
DIGITAL INPUTS
RESET, CTRL1, CTRL2, CTRL3, SCLK, SDATA,
SEN (2) (3)
High-level input voltage
2.4
V
Low-level input voltage
0.8
V
High-level input current
33
µA
Low-level input current
–33
µA
4
pF
High-level output voltage
DRVDD
V
Low-level output voltage
0
V
2
pF
High-level output voltage
1375
mV
Low-level output voltage
1025
mV
350
mV
1200
mV
2
pF
Input capacitance
DIGITAL OUTPUTS
CMOS INTERFACE, DRVDD = 1.65 V to 3.6 V
Output capacitance inside the device, from
each output to ground
Output capacitance
DIGITAL OUTPUTS
LVDS INTERFACE, DRVDD = 3.0 V to 3.6 V, IO = 3.5 mA, RL = 100 Ω
(4)
Output differential voltage, |VOD|
225
VOS Output offset voltage, single-ended
Common-mode voltage of OUTP, OUTM
Output capacitance
Output capacitance inside the device, from
either output to ground
(1)
(2)
(3)
(4)
All LVDS and CMOS specifications are characterized, but not tested at production.
SCLK and SEN function as digital input pins when they are used for serial interface programming. When used as parallel control pins,
analog voltage needs to be applied as per Table 2 and Table 3.
All digital input pins are referred to AVDD supply.
IO refers to the LVDS buffer current setting, RL is the differential load resistance between the LVDS output pair.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
7
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TIMING CHARACTERISTICS – LVDS AND CMOS MODES (1)
Typical values are specified at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock,
1.5 VPP clock amplitude, CL = 5 pF (2), IO = 3.5 mA, RL = 100 Ω (3), no internal termination, unless otherwise noted.
Min and max values are specified across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD = 3.0 V to 3.6 V,
unless otherwise specified.
PARAMETER
TEST CONDITIONS
Aperture
delay
ta
Aperture
delay
variation
ADS62P25
FS = 125 MSPS
Wake-up
time
(to valid
data)
UNIT
MAX
MIN
TYP
MAX
MIN
TYP
MAX
MIN
TYP
MAX
0.7
1.5
2.5
0.7
1.5
2.5
0.7
1.5
2.5
0.7
1.5
2.5
from global
powerdown
ns
±80
±80
±80
±80
ps
150
150
150
150
fs rms
15
50
15
50
15
50
15
50
µs
15
50
15
50
15
50
15
50
µs
CMOS
100
200
100
200
100
200
100
200
ns
LVDS
200
500
200
500
200
500
200
500
from standby
Default, after reset
Latency
ADS62P22
FS = 65 MSPS
TYP
channel-to-channel
within a device
from output
buffer
disable
ADS62P23
FS = 80 MSPS
MIN
Aperture
jitter
tj
ADS62P24
FS = 105 MSPS
ns
14
14
14
14
clock
cycles
with low latency mode
enabled
10
10
10
10
clock
cycles
with digital filter
enabled
15
15
15
15
clock
cycles
DDR LVDS MODE (4), DRVDD = 3.0 V to 3.6V
tsu
Data setup
time (5)
Data valid (6) to
zero-cross of
CLKOUTP
1.7
2.3
2.5
3.1
3.9
4.5
5.4
6.0
ns
th
Data hold
time (5)
Zero-cross of
CLKOUTP to data
becoming invalid (6)
0.7
1.7
0.7
1.7
0.7
1.7
0.7
1.7
ns
tPDI
Clock
propagation
delay
Input clock rising edge
zero-cross to output
clock rising edge
zero-cross
4.3
5.8
7.3
4.3
5.8
7.3
4.3
5.8
7.3
4.3
5.8
7.3
LVDS bit
clock duty
cycle
Duty cycle of
differential clock,
(CLKOUTPCLKOUTM)
10 ≤ Fs ≤ 125 MSPS
40%
47%
55%
40%
47%
55%
40%
47%
55%
40%
47%
55%
Data rise
time,
Data fall
time
Rise time measured
from –50 mV to 50 mV
Fall time measured
from 50 mV to –50 mV
1 ≤ Fs ≤ 125 MSPS
70
100
170
70
100
170
70
100
170
70
100
170
ps
Output clock
rise time,
Output clock
fall time
Rise time measured
from –50 mV to 50 mV
Fall time measured
from 50 mV to –50 mV
1 ≤ Fs ≤ 125 MSPS
70
100
170
70
100
170
70
100
170
70
100
170
ps
5.1
6.6
6.5
8.0
tr
tf
tCLKRI
SE
tCLKFA
LL
PARALLEL CMOS MODE, DRVDD = 2.5 V to 3.6 V, default output buffer drive strength
tsu
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
8
Data setup
time (5)
ns
(7)
(8)
Data valid to 50% of
CLKOUT rising edge
2.9
4.4
3.6
5.1
ns
Timing parameters are specified by design and characterization and not tested in production.
CL is the effective external single-ended load capacitance between each output pin and ground.
IO refers to the LVDS buffer current setting; RL is the differential load resistance between the LVDS output pair.
Measurements are done with a transmission line of 100 Ω characteristic impedance between the device and the load.
Setup and hold time specifications take into account the effect of jitter on the output data and clock.
Data valid refers to logic high of +100 mV and logic low of –100 mV.
For DRVDD < 2.2 V, it is recommended to use external clock for data capture and NOT the device output clock signal (CLKOUT). See
Parallel CMOS interface in application section.
Data valid refers to logic high of 2 V (1.7 V) and logic low of 0.8 V (0.7 V) for DRVDD = 3.3 V (2.5 V).
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TIMING CHARACTERISTICS – LVDS AND CMOS MODES (continued)
Typical values are specified at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock,
1.5 VPP clock amplitude, CL = 5 pF, IO = 3.5 mA, RL = 100 Ω , no internal termination, unless otherwise noted.
Min and max values are specified across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD = 3.0 V to 3.6 V,
unless otherwise specified.
PARAMETER
TEST CONDITIONS
ADS62P25
FS = 125 MSPS
MIN
TYP
ADS62P24
FS = 105 MSPS
MAX
MIN
TYP
2.1
3.5
ADS62P23
FS = 80 MSPS
MAX
MIN
TYP
3.6
5.0
ADS62P22
FS = 65 MSPS
MAX
MIN
TYP
5.1
6.5
UNIT
MAX
th
Data hold
time (5)
50% of CLKOUT rising
edge to data becoming
invalid (8)
1.3
2.7
tPDI
Clock
propagation
delay
Input clock rising edge
zero-cross to 50% of
CLKOUT rising edge
5
6.5
7.9
5
6.5
7.9
5
6.5
7.9
5
6.5
7.9
Output clock
duty cycle
Duty cycle of output
clock (CLKOUT)
10 ≤ Fs ≤ 125 MSPS
45%
50%
55%
45%
50%
55%
45%
50%
55%
45%
50%
55%
Data rise
time
Data fall
time
Rise time measured
from 20% to 80% of
DRVDD
Fall time measured
from 80% to 20% of
DRVDD
1 ≤ Fs ≤ 125 MSPS
0.8
1.5
2.4
0.8
1.5
2.4
0.8
1.5
2.4
0.8
1.5
2.4
ns
Output clock
rise time
Output clock
fall time
Rise time measured
from 20% to 80% of
DRVDD
Fall time measured
from 80% to 20% of
DRVDD
1 ≤ Fs ≤ 125 MSPS
0.8
1.5
2.4
0.8
1.5
2.4
0.8
1.5
2.4
0.8
1.5
2.4
ns
tr
tf
tCLKRI
SE
tCLKFA
LL
ns
ns
Timing Characteristics at Lower Sampling Frequencies
SAMPLING
FREQUENCY,
MSPS
tsu DATA SETUP TIME, ns
MIN
TYP
MAX
th DATA HOLD TIME, ns
MIN
TYP
MAX
tPDI CLOCK PROPAGATION DELAY,
ns
MIN
TYP
MAX
5.8
7.3
8.8
3.5
5.5
7.5
CMOS INTERFACE, DRVDD = 2.5 V TO 3.6 V
40
10.5
12
10.3
11.8
20
23
24.5
23
24.5
LVDS INTERFACE, DRVDD = 3.0 V to 3.6 V
40
8.5
10
1
2.3
20
21
22.5
1
2.3
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
9
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
N+4
N+3
N+2
N+16
N+15
N+1
Sample
N
N+14
Input
Signal
ta
CLKM
Input
Clock
CLKP
CLKOUTM
CLKOUTP
tsu
14 Clock Cycles
DDR
LVDS
Output Data
DXP, DXM
O
E
E
O
O
E
O
E
E – Even Bits D0,D2,D4,D6,D8,D10
O – Odd Bits D1,D3,D5,D7,D9,D11
(1)
O
tPDI
th
E
E
O
N–10
E
O
N–1
N–9
E
O
E
O
N+1
N
E
O
N+2
tPDI
CLKOUT
tsu
Parallel
CMOS
14 Clock Cycles
Output Data
D0–D11
(1)
N–10
th
N–9
N–1
N
N+1
N+2
T0105-07
(1)
Latency is 10 clock cycles in low-latency mode.
Figure 1. Latency
Input
Clock
CLKM
Input
Clock
CLKP
CLKM
CLKP
tPDI
Output
Clock
tPDI
CLKOUTM
Output
Clock
CLKOUTP
th
tsu
tsu
Output
Data Pair
(1)
(2)
Dn
Dn_Dn+1_P,
Dn_Dn+1_M
CLKOUT
th
th
Dn
(1)
Dn+1
tsu
(2)
Output
Data
– Bits D0, D2, D4, D6, D8, D10
(1)
Dn+1 – Bits D1, D3, D5, D7, D9, D11
Dn
Dn
(1)
Dn – Bits D0 to D11
T0107-03
T0106-05
Figure 2. LVDS Mode Timing
10
Submit Documentation Feedback
Figure 3. CMOS Mode Timing
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DEVICE CONFIGURATION
ADS62P2X can be configured independently using either parallel interface control or serial interface
programming.
USING PARALLEL INTERFACE CONTROL ONLY
To control the device using the parallel interface, keep RESET tied to high (AVDD). Pins SEN, SCLK, CTRL1,
CTRL2 and CTRL3 can be used to directly control certain modes of the ADC. After power-up, the device will
automatically get configured as per the parallel pin voltage settings (Table 2 to Table 4).
In this mode, SEN and SCLK function as parallel analog control pins, which can be configured using a simple
resistor divider (Figure 4). Table 1 has a brief description of the modes controlled by the parallel pins.
Table 1. Parallel Pin Definition
PIN
SCLK
SEN
CTRL1
CTRL2
CTRL3
TYPE OF PIN
Analog control pins
(controlled by analog
voltage levels, see )
Digital control pins
(controlled by digital
logic levels)
CONTROLS MODES
Coarse gain and internal/external reference
LVDS/CMOS interface and output data format
Together control various power down modes and MUX mode.
USING SERIAL INTERFACE PROGRAMMING ONLY
To program the device using the serial interface, keep RESET low. Pins SEN, SDATA, and SCLK function as
serial interface digital pins and are used to access the internal registers of ADC. The registers must first be reset
to their default values either by applying a pulse on RESET pin or by setting bit <RST> = 1. After reset, the
RESET pin must be kept low.
The serial interface section describes the register programming and register reset in more detail. Since the
parallel pins (CTRL1, CTRL2, CTRL3) are not used in this mode, they must be tied to ground.
USING BOTH SERIAL INTERFACE and PARALLEL CONTROLS
For increased flexibility, a combination of serial interface registers and parallel pin controls (CTRL1 to CTRL3)
can also be used to configure the device. To allow this, keep RESET low.
The parallel interface control pins CTRL1 to CTRL3 are available. After power-up, the device will automatically
get configured as per the voltage settings on these pins (Table 4).
SEN, SDATA, and SCLK function as serial interface digital pins and are used to access the internal registers of
ADC. The registers must first be reset to their default values either by applying a pulse on RESET pin or by
setting bit <RST> = 1. After reset, the RESET pin must be kept low. The serial interface section describes the
register programming and register reset in more detail.
Since the power down modes can be controlled using both the parallel pins and serial registers, the priority
between the two is determined by <OVRD> bit. When <OVRD> bit = 0, pins CTRL1 to CTRL3 control the power
down modes. With <OVRD> = 1, register bits <POWER DOWN> control these modes, over-riding the pin
settings.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
11
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DETAILS OF PARALLEL CONFIGURATION ONLY
The functions controlled by each parallel pin are described below. A simple way of configuring the parallel pins is
shown in Figure 4.
Table 2. SCLK (Analog Control Pin)
SCLK
DESCRIPTION
0
0dB gain and internal reference
(3/8)AVDD
0dB gain and external reference
(5/8)2AVDD
3.5dB coarse gain and external reference
AVDD
3.5dB coarse gain and internal reference
Table 3. SEN (Analog Control Pin)
SEN
DESCRIPTION
0
2s complement format and DDR LVDS output
(3/8)AVDD
Straight binary and DDR LVDS output
(5/8)AVDD
Straight binary and parallel CMOS output
AVDD
2s complement format and parallel CMOS output
Table 4. CTRL1, CTRL2 and CTRL3 (Digital Control Pins)
CTRL1
CTRL2
CTRL3
LOW
LOW
LOW
Normal operation
DESCRIPTION
LOW
LOW
HIGH
Channel A output buffer disabled
LOW
HIGH
LOW
Channel B output buffer disabled
LOW
HIGH
HIGH
Channel A and B output buffer disabled
HIGH
LOW
LOW
Channel A and B powered down
HIGH
LOW
HIGH
Channel A standby
HIGH
HIGH
LOW
Channel B standby
HIGH
HIGH
HIGH
MUX mode of operation (only with CMOS interface Channel A and B data is multiplexed and
output on DB10 to DB0 pins. See multiplexed output mode for detailed description.
AVDD
(5/8) AVDD
3R
(5/8) AVDD
GND
AVDD
2R
(3/8) AVDD
(3/8) AVDD
3R
To Parallel Pin
GND
S0321-01
Figure 4. Simple Scheme to Configure Parallel Pins
12
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
SERIAL INTERFACE
The ADC has a set of internal registers, which can be accessed by the serial interface formed by pins SEN
(Serial interface Enable), SCLK (Serial Interface Clock) and SDATA (Serial Interface Data).
Serial shift of bits into the device is enabled when SEN is low. Serial data SDATA is latched at every falling edge
of SCLK when SEN is active (low). The serial data is loaded into the register at every 16th SCLK falling edge
when SEN is low. In case the word length exceeds a multiple of 16 bits, the excess bits are ignored. Data can be
loaded in multiple of 16-bit words within a single active SEN pulse.
The first 8 bits form the register address and the remaining 8 bits the register data. The interface can work with
SCLK frequency from 20 MHz down to low speeds (few Hertz), and also with a non-50% SCLK duty cycle.
Register Initialization
After power-up, the internal registers must be initialized to their default values. This can be done in one of two
ways:
1. Either through hardware reset by applying a high-going pulse on RESET pin (of width greater than 10 ns) as
shown in Figure 5.
OR
2. By applying software reset. Using the serial interface, set the <RST> bit to high. This initializes internal
registers to their default values and then self-resets the <RST> bit to low. In this case the RESET pin is kept
low.
SERIAL INTERFACE TIMING CHARACTERISTICS
Typical values at 25°C, min and max values across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD = 3.3 V,
DRVDD = 1.8 V to 3.3 V, unless otherwise noted.
PARAMETER
MIN
> DC
TYP
MAX
UNIT
20
MHz
fSCLK
SCLK frequency
tSLOADS
SEN to SCLK setup time
25
ns
tSLOADH
SCLK to SEN hold time
25
ns
tDSU
SDATA setup time
25
ns
tDH
SDATA hold time
25
ns
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
13
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Register Data
Register Address
SDATA
A7
A6
A5
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
t(DH)
t(SCLK)
t(DSU)
SCLK
t(SLOADH)
t(SLOADS)
SEN
RESET
T0109-01
Figure 5. Serial Interface Timing
RESET TIMING
Typical values at 25°C, min and max values across the full temperature range TMIN = –40°C to TMAX = 85°C, unless otherwise
noted.
PARAMETER
CONDITIONS
MIN
t1
Power-on delay
Delay from power-up of AVDD and DRVDD to RESET pulse
active
t2
Reset pulse width
t3
Register write delay
tPO
Power-up time
Delay from power-up of AVDD and DRVDD to output stable
TYP
MAX
UNIT
5
ms
Pulse width of active RESET signal
10
ns
Delay from RESET disable to SEN active
25
ns
7
ms
Power Supply
AVDD, DRVDD
t1
RESET
t2
t3
SEN
T0108-01
NOTE: A high-going pulse on RESET pin is required in serial interface mode in case of initialization through hardware reset.
For parallel interface operation, RESET has to be tied permanently HIGH.
Figure 6. Reset Timing Diagram
14
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
SERIAL REGISTER MAP
Table 5. Summary of Functions Supported by Serial Interface (1)
REGISTER
ADDRESS
REGISTER FUNCTIONS
A7–A0 IN
HEX
D7
D6
D5
D4
D3
D2
D1
D0
00
0
0
0
0
0
0
<RST>
Software Reset
0
0
0
0
0
0
0
10
<CLKOUT
STRENGTH>
<CURRENT DOUBLE>
LVDS buffer current double
<DATAOUT
STRENGTH>
0
0
12
0
0
13
0
0
0
<OFFSET FREEZE>
0
14
<OVRD>
Over-ride
bit
0
<OUTPUT
INTERFACE>
LVDS or CMOS
interface
<COARSE GAIN>
3.5 dB gain
<REF>
Internal/External
reference
<POWER DOWN MODES>
and
MUX mode
16
0
0
0
<DATA FORMAT>
2s complement or straight
binary
Bit/Byte wise
(LVDS only)
<TEST PATTERNS>
17
0
0
0
0
19
0
0
1A
<LOW
LATENCY>
1B
<OFFSET
EN>
Other
correction
enable
0
<FILTER COEFF
SELECT>
In-built or custom
coefficients
<FILTER ENABLE>
Enable digital filtering
<ODD TAP
ENABLE>
1D
0
0
0
0
0
<LVDS TERMINATION>
Internal termination programmability
18
1E to 2F
(1)
<LVDS CURRENT>
LVDS buffer current
programmability
11
0
0
0
<FINE GAIN>
0 to 6 dB gain in 0.5 dB steps
<CUSTOM LOW> Lower 6 bits
<CUSTOM HIGH> Upper 6 bits
<OFFSET TC>
Offset correction time constant
<GAIN CORRECTION>
0 to 0.5 dB, steps of 0.05 dB
<DECIMATION RATE>
Decimate by 2, 4, 8
0
<DECIMATION FILTER
FREQ BANDS>
<FILTER COEFFICIENTS> 12 coefficients, each 12 bit signed
Multiple functions in a register can be programmed in a single write operation.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
15
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DESCRIPTION OF SERIAL REGISTERS
Table 6.
A7–A0
(hex)
D7
D6
D5
D4
D3
D2
D1
D0
00
0
0
0
0
0
0
<RST>
Software Reset
0
D1
1
<RST>
Software reset applied – resets all internal registers and self-clears to 0.
Table 7.
A7–A0
(hex)
10
D7
D6
<CLKOUT STRENGTH>
D7–D6
01
00
11
10
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
D2
D1
D0
<CLKOUT STRENGTH> Output clock buffer drive strength control
WEAKER than default drive
DEFAULT drive strength
STRONGER than default drive strength (recommended for load capacitances > 5 pF)
MAXIMUM drive strength (recommended for load capacitances > 5 pF)
Table 8.
A7–A0
(hex)
D7
D6
11
0
0
D5
D4
<CURRENT DOUBLE>
LVDS buffer current double
D3
LVDS CURRENT> LVDS
buffer current
programmability
D1–D0
01
00
11
10
<DATAOUT STRENGTH> Output data buffer drive strength control
WEAKER than default drive
DEFAULT drive strength
STRONGER than default drive strength (recommended for load capacitances > 5 pF)
MAXIMUM drive strength (recommended for load capacitances > 5 pF)
D3–D2
00
01
10
11
<LVDS CURRENT> LVDS Current programmability
3.5 mA
2.5 mA
4.5 mA
1.75 mA
D5–D4
00
01
10
11
CURRENT DOUBLE> LVDS Current double control
default current, set by <LVDS CURR>
LVDS clock buffer current is doubled, 2x <LVDS CURR>
LVDS data and clock buffers current are doubled, 2x <LVDS CURR>
unused
16
Submit Documentation Feedback
DATAOUT STRENGTH>
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Table 9.
A7–A0
(hex)
D7
D6
12
0
0
D5
D4
D3
D2
D1
D0
<LVDS TERMINATION> Internal termination programmability
D5–D3
000
001
010
011
100
101
110
111
<LVDS DATA TERM> Internal termination control for data outputs
No internal termination
300 Ω
180 Ω
110 Ω
150 Ω
100 Ω
81 Ω
60 Ω
D2–D0
000
001
010
011
100
101
110
111
<LVDS CLK TERM> Internal termination control for clock output
No internal termination
300 Ω
180 Ω
110 Ω
150 Ω
100 Ω
81 Ω
60 Ω
Table 10.
D4
0
1
A7–A0
(hex)
D7
D6
D5
D4
D3
D2
D1
D0
13
0
0
0
<OFFSET FREEZE>
0
0
0
0
<OFFSET FREEZE> Offset correction becomes inactive and the last estimated offset value is used to cancel the offset
Offset correction active
Offset correction inactive
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
17
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Table 11.
A7–A0
(hex)
D7
14
<OVRD>
Over-ride bit
D6
D5
D4
D3
0
<OUTPUT
INTERFACE>
LVDS or CMOS
interface
<COARSE GAIN>
3.5 dB gain
<REF>
Internal / External
reference
D2
D1
D0
<POWER DOWN
MODES>
D2-D0
000
001
010
011
100
101
110
111
<POWER DOWN MODES>
Normal operation
Channel A output buffer disabled
Channel B output buffer disabled
Channel A and B output buffers disabled
Global power down
Channel A standby
Channel B standby
Multiplexed mode, MUX– (only with CMOS interface)
Channel A and B data is multiplexed and output on DA10 to DA0 pins.
D3
0
1
<REF> Reference mode
Internal reference enabled
External reference enabled
D4
0
1
<COARSE GAIN> Coarse gain control
0 dB coarse gain
3.5 dB coarse gain
D5
0
1
<OUTPUT INTERFACE> Output interface selection
Parallel CMOS data outputs
DDR LVDS data outputs
D7
<OVRD> Over-ride bit – the LVDS/CMOS selection, power down and MUX modes can also be controlled using parallel pins.
By setting <OVRD> = 1, register bits LVDS <CMOS> and <POWER DOWN MODES> will over-ride the settings of the parallel
pins.
Disable over-ride
Enable over-ride
0
1
Table 12.
A7–A0
(hex)
D7
D6
D5
D4
D3
16
0
0
0
DATA FORMAT>
2s complement or straight binary
Bit / Byte wise (LVDS only)
D2
D1
D0
<TEST PATTERNS>
D2–D0
000
001
010
011
100
101
110
111
<TEST PATTERNS> Test Patterns to verify capture
Normal ADC operation
Outputs all zeros
Outputs all ones
Outputs toggle pattern
Outputs digital ramp
Outputs custom pattern
Unused
Unused
D3
0
1
Bit-wise/Byte-wise selection (DDR LVDS mode ONLY)
Bit wise – Odd bits (D1, D3, D5, D7, D9) on CLKOUT rising edge and even bits (D0, D2, D4, D6, D8, D10) on CLKOUT
falling edge
Byte wise – Lower 7 bits (D0-D6) at CLKOUT rising edge and upper 4 bits (D7-D10) at CLKOUT falling edge
D4
0
1
<DATA FORMAT> Data format selection
2s complement
Straight binary
18
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Table 13.
A7–A0
(hex)
D7
D6
D5
D4
17
0
0
0
0
D2–D0
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
Others
D3
D2
D1
D0
<FINE GAIN> 0 to 6 dB gain in 0.5 dB steps
<FINE GAIN> Gain programmability in 0.5 dB steps
0 dB gain, default after reset
0.5 dB gain
1.0 dB gain
1.5 dB gain
2.0 dB gain
2.5 dB gain
3.0 dB gain
3.5 dB gain
4.0 dB gain
4.5 dB gain
5.0 dB gain
5.5 dB gain
6.0 dB gain
Unused
Table 14.
A7–A0
(hex)
D7
D6
18
19
D5
D4
D3
D2
D1
D0
<CUSTOM LOW> Lower 6 bits
0
0
<CUSTOM HIGH> Upper 6 bits
D7-D2
<CUSTOM LOW>
6 lower bits of custom pattern available at the output instead of ADC data.
D5-D0
<CUSTOM HIGH>
6 upper bits of custom pattern available at the output instead of ADC data.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
19
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Table 15.
A7–A0
(hex)
D7
1A
<LOW LATENCY>
D6
D5
D4
D3
<OFFSET TC>
Offset correction time constant
D2
D1
D0
<GAIN CORRECTION>
0 to 0.5 dB, steps of 0.05 dB
D2–D0
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
<GAIN CORRECTION> Enables fine gain correction in steps of 0.05 dB (same correction applies to both channels)
0 dB gain, default after reset
+0.5 dB gain
+0.10 dB gain
+0.15 dB gain
+0.20 dB gain
+0.25 dB gain
+0.30 dB gain
+0.35 dB gain
+0.40 dB gain
+0.45 dB gain
+0.5 dB gain
D6-D4
000
001
010
011
100
101
110
111
<OFFSET TC> Time constant of offset correction in number of clock cycles (seconds, for sampling frequency = 125
MSPS)
227 (1.1 s)
226 (0.55 s)
225 (0.27 s)
224 (0.13 s)
228 (2.15 s)
229 (4.3 s)
227 (1.1 s)
227 (1.1 s)
D7
0
1
<LOW LATENCY>
Default latency, 14 clock cycles
Low latency enabled, 10 clock cycles – Digital Processing Block is bypassed.
Table 16.
A7–A0
(hex)
D7
D6
D5
D4
D3
1B
<OFFSET Enable>
Offset correction
enable
0
<FILTER COEFF
SELECT>
In-built or custom
coefficients
<FILTER Enable>
Enable digital filtering
<ODD TAP
Enable>
D2-D0
000
001
011
100
<DECIMATION RATE> Decimation filters
Decimate by 2 (pre-defined or user coefficients can be used)
Decimate by 4 (pre-defined or user coefficients can be used)
No decimation (pre-defined coefficients are disabled, only custom coefficients are available)
Decimate by 8 (only custom coefficients are available)
D3
0
1
<ODD TAP ENABLE>
Even taps enabled (24 coefficients)
0 Odd taps enabled (23 coefficients)
D4
0
1
<FILTER ENABLE>
Digital filter bypassed
Digital filtering enabled
D5
0
1
<FILTER COEFF SELECT>
Pre-defined coefficients are loaded in the filter
User-defined coefficients are loaded in the filter (coefficients have to be loaded in registers – to - )
D7
0
1
<OFFSET Enable>
Offset correction disabled
Offset correction enabled
20
Submit Documentation Feedback
D2
D1
D0
<DECIMATION RATE>
Decimate by 2,4,8
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Table 17.
A7–A0
(hex)
D7
D6
D5
D4
D3
D2
1D
0
0
0
0
0
0
D1-D0
00
01
10, 11
<DECIMATION FILTER FREQ BAND> Decimation filters
With decimate by 2, <DECIMATION RATE> = 000:
Low-pass filter (–6 dB frequency at Fs/4)
High-pass filter (–6 dB frequency at Fs/4)
Unused
00
01
10
11
With decimate by 4, <DECIMATION RATE> = 001:
Low-pass filter (-3 dB frequency at Fs/8)
Band-pass filter (center frequency at 3Fs/16)
Band-pass filter (center frequency at 5Fs/16)
High-pass filter (-3 dB frequency at 3Fs/8)
Copyright © 2007–2008, Texas Instruments Incorporated
D1
D0
<DECIMATION FILTER FREQ BANDS>
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
21
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
PIN CONFIGURATION (CMOS MODE)
DRGND
DA6
DA7
DA8
DA9
DA10
DA11
NC
CLKOUT
DRVDD
DRGND
NC
NC
DB0
DB1
DRGND
RGC PACKAGE
(TOP VIEW)
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
48
DRVDD
DB2
2
47
DA5
DB3
3
46
DA4
DB4
4
45
DA3
DB5
5
44
DA2
DB6
6
43
DA1
DB7
7
42
DA0
DB8
8
41
NC
DB9
9
40
NC
DRVDD
PAD
(Connected to DRGND)
CTRL2
SDATA
14
35
CTRL1
SEN
15
34
AVDD
16
33
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
AVDD
AGND
AVDD
AGND
36
AGND
13
INM_A
SCLK
INP_A
CTRL3
AGND
37
AGND
12
CLKM
RESET
CLKP
DRVDD
AGND
38
VCM
11
AGND
DB11
AGND
DRGND
INM_B
39
INP_B
10
AGND
DB10
P0056-11
Pin Assignments (CMOS INTERFACE)
PIN NAME
DESCRIPTION
AVDD
Analog power supply
AGND
Analog ground
CLKP, CLKM
INP_A, INM_A
PIN NUMBER
NUMBER OF
PINS
16, 33, 34
3
17, 18, 21, 22, 24,
27, 28, 31, 32
9
Differential input clock
25, 26
2
Differential input signal – channel A
29, 30
2
INP_B, INM_B
Differential input signal – channel B
19, 20
2
VCM
Internal reference mode – Common-mode voltage output.
External reference mode – Reference input. The voltage forced on this pin sets
the ADC internal references.
23
1
RESET
Serial interface RESET input.
In serial interface mode, the user must initialize internal registers through
hardware RESET by applying a high-going pulse on this pin or by using
software reset (refer to Serial Interface section).
In parallel interface mode, the user has to tie RESET pin permanently high.
(SCLK, SDATA and SEN are used as parallel pin controls in this mode) The pin
has an internal 100 kΩ pull-down resistor.
12
1
22
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Pin Assignments (CMOS INTERFACE) (continued)
PIN NAME
DESCRIPTION
PIN NUMBER
NUMBER OF
PINS
SCLK
This pin functions as serial interface clock input when RESET is low.
It functions as analog control pin when RESET is tied high and controls coarse
gain and internal/external reference selection. See Table 2 for details.
The pin has an internal pull-down resistor to ground.
13
1
SDATA
This pin functions as serial interface data input when RESET is low. The pin has
an internal pull-down resistor to ground.
14
1
SEN
This pin functions as serial interface enable input when RESET is low.
It functions as analog control pin when RESET is tied high and controls the
output interface (LVDS/CMOS) and data format selection. See Table 3 for
details.
The pin has an internal pull-up resistor to AVDD.
15
1
CTRL1
These are digital logic input pins. Together they control various power down and
multiplexed mode. see Table 4 for details
35
1
36
1
CTRL2
CTRL3
37
1
DA11 to DA0
Channel A 12-bit data outputs, CMOS
42-47, 50-55
12
DB11 to DB0
Channel B 12-bit data outputs, CMOS
62-63, 2-11
12
CLKOUT
CMOS output clock
57
1
DRVDD
Digital supply
1, 38, 48, 58
4
DRGND
Digital ground
39, 49, 59, 64 and
PAD
4
PAD
Digital ground. Solder the pad to the digital ground on the board using multiple
vias for good electrical and thermal performance.
–
1
NC
Do not connect
40,41,60,61,56
5
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
23
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
PIN CONFIGURATION (LVDS MODE)
DRGND
DA6M
DA6P
DA8M
DA8P
DA10M
DA10P
CLKOUTM
CLKOUTP
DRVDD
DRGND
NC
NC
DB0M
DB0P
DRGND
RGC PACKAGE
(TOP VIEW)
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
48
DRVDD
DB2M
2
47
DA4P
DB2P
3
46
DA4M
DB4M
4
45
DA2P
DB4P
5
44
DA2M
DB6M
6
43
DA0P
DB6P
7
42
DA0M
DB8M
8
41
NC
DB8P
9
40
NC
DRVDD
PAD
(Connected to DRGND)
CTRL2
SDATA
14
35
CTRL1
SEN
15
34
AVDD
16
33
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
AVDD
AGND
AVDD
AGND
36
AGND
13
INM_A
SCLK
INP_A
CTRL3
AGND
37
AGND
12
CLKM
RESET
CLKP
DRVDD
AGND
38
VCM
11
AGND
DB10P
AGND
DRGND
INM_B
39
INP_B
10
AGND
DB10M
P0056-12
Pin Assignments (LVDS INTERFACE)
PIN NAME
DESCRIPTION
PIN
NUMBER
NUMBER OF
PINS
AVDD
Analog power supply
16, 33, 34
3
AGND
Analog ground
17, 18, 21,
22, 24, 27,
28, 31,32
9
CLKP, CLKM
Differential input clock
25, 26
2
INP_A, INM_A
Differential input signal – Channel A
29, 30
2
INP_B, INM_B
Differential input signal – Channel B
19, 20
2
VCM
Internal reference mode – Common-mode voltage output.
External reference mode – Reference input. The voltage forced on this pin sets the
ADC internal references.
23
1
RESET
Serial interface RESET input.
In serial interface mode, the user must initialize internal registers through hardware
RESET by applying a high-going pulse on this pin or by using software reset (refer to
Serial Interface section).
In parallel interface mode, the user has to tie RESET pin permanently high. (SCLK,
SDATA and SEN are used as parallel pin controls in this mode) The pin has an internal
100 kΩ pull-down resistor.
12
1
24
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Pin Assignments (LVDS INTERFACE) (continued)
PIN NAME
DESCRIPTION
PIN
NUMBER
NUMBER OF
PINS
SCLK
This pin functions as serial interface clock input when RESET is low.
It functions as analog control pin when RESET is tied high and controls coarse gain
and internal/external reference selection. See Table 2 for details.
The pin has an internal pull-down resistor to ground.
13
1
SDATA
This pin functions as serial interface data input when RESET is low. The pin has an
internal pull-down resistor to ground.
14
1
SEN
This pin functions as serial interface enable input when RESET is low.
It functions as analog control pin when RESET is tied high and controls the output
interface (LVDS/CMOS) and data format selection. See Table 3 for details.
The pin has an internal pull-up resistor to AVDD.
15
1
CTRL1
These are digital logic input pins. Together they control various power down and
multiplexed mode. See Table 4 for details.
35
1
36
1
37
1
CTRL2
CTRL3
DA0P
Channel A Differential output data D0 and D1 multiplexed, true
43
1
DA0M
Channel A Differential output data D0 and D1 multiplexed, complement
42
1
DA2P
Channel A Differential output data D2 and D3 multiplexed, true
45
1
DA2M
Channel A Differential output data D2 and D3 multiplexed, complement
44
1
DA4P
Channel A Differential output data D4 and D5 multiplexed, true
47
1
DA4M
Channel A Differential output data D4 and D5 multiplexed, complement
46
1
DA6P
Channel A Differential output data D6 and D7 multiplexed, true
51
1
DA6M
Channel A Differential output data D6 and D7 multiplexed, complement
50
1
DA8P
Channel A Differential output data D8 and D9 multiplexed, true
53
1
DA8M
Channel A Differential output data D8 and D9 multiplexed, complement
52
1
DA10P
Channel A Differential output data D10 and D11 multiplexed, true
55
1
DA10M
Channel A Differential output data D10 and D11 multiplexed, complement
54
1
CLKOUTP
Differential output clock, true
57
1
CLKOUTM
Differential output clock, complement
56
1
DB0P
Channel B Differential output data D0 and D1 multiplexed, true
63
1
DB0M
Channel B Differential output data D0 and D1 multiplexed, complement
62
1
DB2P
Channel B Differential output data D2 and D3 multiplexed, true
3
1
DB2M
Channel B Differential output data D2 and D3 multiplexed, complement
2
1
DB4P
Channel B Differential output data D4 and D5 multiplexed, true
5
1
DB4M
Channel B Differential output data D4 and D5 multiplexed, complement
4
1
DB6P
Channel B Differential output data D6 and D7 multiplexed, true
7
1
DB6M
Channel B Differential output data D6 and D7 multiplexed, complement
6
1
DB8P
Channel B Differential output data D8 and D9 multiplexed, true
9
1
DB8M
Channel B Differential output data D8 and D9 multiplexed, complement
8
1
DB10P
Channel B Differential output data D10 and D11 multiplexed, true
11
1
DB10M
Channel B Differential output data D10 and D11 multiplexed, complement
10
1
DRVDD
Digital supply
1, 38, 48,
58
4
DRGND
Digital ground
39, 49, 59,
64 and PAD
4
PAD
Digital ground. Solder the pad to the digital ground on the board using multiple vias for
good electrical and thermal performance.
–
1
NC
Do not connect
40,41,60,61
4
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
25
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P25 (FS= 125 MSPS)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
FFT for 20 MHz INPUT SIGNAL
FFT for 70 MHz INPUT SIGNAL
0
0
SFDR = 88.31 dBc
SINAD = 70.95 dBFS
SNR = 71.03 dBFS
THD = 87.1 dBc
−20
−40
Amplitude − dB
Amplitude − dB
−40
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
40
50
60
f − Frequency − MHz
0
10
20
30
60
G001
G002
Figure 8.
FFT for 190 MHz INPUT SIGNAL
INTERMODULATION DISTORTION (IMD) vs FREQUENCY
0
fIN1 = 190.1 MHz, –7 dBFS
fIN2 = 185.3 MHz, –7 dBFS
2-Tone IMD = –88.5 dBFS
SFDR = –96.08 dBFS
−20
−40
Amplitude − dB
−40
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
40
50
60
f − Frequency − MHz
0
10
20
30
40
50
60
f − Frequency − MHz
G003
Figure 9.
G004
Figure 10.
SFDR vs INPUT FREQUENCY
SNR vs INPUT FREQUENCY
94
74
92
73
Gain = 3.5 dB
90
72
88
SNR − dBFS
SFDR − dBc
50
Figure 7.
SFDR = 78.88 dBc
SINAD = 69.49 dBFS
SNR = 70.11 dBFS
THD = 77.27 dBc
−20
86
84
82
Gain = 0 dB
71
70
Gain = 3.5 dB
69
68
Gain = 0 dB
80
67
78
76
66
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
Figure 11.
26
40
f − Frequency − MHz
0
Amplitude − dB
SFDR = 86.51 dBc
SINAD = 70.88 dBFS
SNR = 71.01 dBFS
THD = 85.12 dBc
−20
Submit Documentation Feedback
175
200
G005
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
175
200
G006
Figure 12.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P25 (FS= 125 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
SFDR vs INPUT FREQUENCY (LVDS interface)
SFDR vs INPUT FREQUENCY ACROSS GAIN
94
94
92
Input adjusted to get −1dBFS input
4 dB
92
90
90
88
88
SFDR − dBc
86
84
86
84
82
5 dB
82
Gain = 0 dB
80
78
78
76
76
0
25
50
75
100
125
150
175
200
fIN − Input Frequency − MHz
6 dB
1 dB
0 dB
0
25
50
75
G007
Figure 13.
SINAD vs INPUT FREQUENCY ACROSS GAIN
175
200
G009
PERFORMANCE vs AVDD
Input adjusted to get −1dBFS input
0 dB
89
1 dB
71
SINAD − dBFS
150
90
72
2 dB
SFDR − dBc
3 dB
70
69
68
67
4 dB
66
5 dB
0
20
40
60
76
fIN = 70.1 MHz
DRVDD = 3.3 V
75
SFDR
88
74
87
73
86
80
85
71
84
70
83
69
82
3.0
100 120 140 160 180 200
fIN − Input Frequency − MHz
3.1
3.2
PERFORMANCE vs DRVDD
fIN = 70.1 MHz
AVDD = 3.3 V
G011
89
75
fIN = 70.1 MHz
75
88
74
73
86
72
SNR
85
71
84
70
83
69
3.4
DRVDD − Supply Voltage − V
Figure 17.
Copyright © 2007–2008, Texas Instruments Incorporated
3.5
SNR − dBFS
87
68
3.6
SFDR − dBc
74
SFDR
3.3
68
3.6
3.5
PERFORMANCE vs TEMPERATURE
76
3.2
3.4
Figure 16.
90
3.1
3.3
AVDD − Supply Voltage − V
G010
Figure 15.
88
72
SNR
6 dB
65
SFDR − dBc
125
Figure 14.
73
82
3.0
100
fIN − Input Frequency − MHz
SNR − dBFS
80
89
3 dB
2 dB
87
86
72
SNR
85
71
84
70
83
−40
G012
73
SFDR
SNR − dBFS
SFDR − dBc
Gain = 3.5 dB
69
−20
0
20
40
60
80
T − Temperature − °C
G013
Figure 18.
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
27
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P25 (FS= 125 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
PERFORMANCE vs INPUT AMPLITUDE
PERFORMANCE vs CLOCK AMPLITUDE
90
SFDR (dBFS)
90
80
90
74
80
75
88
73
70
70
SNR (dBFS)
60
65
50
SFDR (dBc)
30
−60
fIN = 20.1 MHz
−50
−40
−30
−20
−10
SFDR − dBc
92
40
86
72
SNR
71
60
82
70
55
80
69
50
78
0.5
0
1.0
1.5
2.0
2.5
Figure 20.
PERFORMANCE vs INPUT CLOCK DUTY CYCLE
OUTPUT NOISE HISTOGRAM
(INPUTS TIED TO COMMON-MODE)
76
60
75
74
86
73
84
72
SNR
82
71
80
70
78
69
76
SNR − dBFS
SFDR
88
Occurence − %
90
G015
70
77
fIN = 20.1 MHz
68
3.0
Input Clock Amplitude − VPP
G014
Figure 19.
94
92
75
SFDR
84
Input Amplitude − dBFS
SFDR − dBc
76
fIN = 20.1 MHz
85
SNR − dBFS
SFDR − dBc, dBFS
100
94
SNR − dBFS
110
50
40
30
20
10
0
68
30
35
40
45
50
55
60
65
70
Input Clock Duty Cycle − %
2040 2041 2042 2043 2044 2045 2046 2047 2048
Output Code
G016
Figure 21.
G017
Figure 22.
PERFORMANCE IN EXTERNAL REFERENCE MODE
93
78
fIN = 20.1 MHz
External Reference Mode
SFDR
76
89
74
87
72
SNR
85
83
1.35
SNR − dBFS
SFDR − dBc
91
70
1.40
1.45
1.50
1.55
VVCM − VCM Voltage − V
1.60
68
1.65
G018
Figure 23.
28
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P24 (FS= 105 MSPS)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
FFT for 20 MHz INPUT SIGNAL
FFT for 70 MHz INPUT SIGNAL
0
0
SFDR = 88.38 dBc
SINAD = 71.02 dBFS
SNR = 71.09 dBFS
THD = 87.61 dBc
−20
−40
Amplitude − dB
Amplitude − dB
−40
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
40
50
f − Frequency − MHz
0
10
20
30
40
50
f − Frequency − MHz
G019
G020
Figure 24.
Figure 25.
FFT for 190 MHz INPUT SIGNAL
INTERMODULATION DISTORTION (IMD) vs FREQUENCY
0
0
SFDR = 82.51 dBc
SINAD = 69.71 dBFS
SNR = 70.04 dBFS
THD = 80.13 dBc
−20
fIN1 = 190.1 MHz, –7 dBFS
fIN2 = 185.3 MHz, –7 dBFS
2-Tone IMD = –87 dBFS
SFDR = –90 dBFS
−20
−40
Amplitude − dB
−40
Amplitude − dB
SFDR = 84.17 dBc
SINAD = 70.8 dBFS
SNR = 71.01 dBFS
THD = 83 dBc
−20
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
40
50
f − Frequency − MHz
0
10
20
30
40
50
f − Frequency − MHz
G021
Figure 26.
G022
Figure 27.
SFDR vs INPUT FREQUENCY
SNR vs INPUT FREQUENCY
74
98
96
Gain = 3.5 dB
73
94
SNR − dBFS
SFDR − dBc
92
90
88
86
84
72
Gain = 0 dB
71
70
Gain = 3.5 dB
82
80
69
Gain = 0 dB
78
68
76
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
Figure 28.
Copyright © 2007–2008, Texas Instruments Incorporated
175
200
G023
0
25
50
75
100
125
150
175
fIN − Input Frequency − MHz
200
G024
Figure 29.
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
29
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P24 (FS= 105 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
SFDR vs INPUT FREQUENCY (LVDS interface)
SFDR vs INPUT FREQUENCY ACROSS GAIN
96
96
94
94
Gain = 3.5 dB
92
92
88
86
2 dB
5 dB
88
86
84
84
80
80
78
78
0
25
50
75
100
4 dB
82
Gain = 0 dB
125
150
175
200
fIN − Input Frequency − MHz
6 dB
0
25
50
G025
SINAD vs INPUT FREQUENCY ACROSS GAIN
150
175
200
G027
PERFORMANCE vs AVDD
Input adjusted to get −1dBFS input
0 dB
87
1 dB
2 dB
3 dB
70
69
68
67
4 dB
66
5 dB
25
50
75
SFDR
74
85
73
84
72
SNR
83
71
82
70
81
69
6 dB
80
3.0
65
0
76
fIN = 70.1 MHz
DRVDD = 3.31 V
86
SFDR − dBc
71
75
100
125
150
fIN − Input Frequency − MHz
175
200
3.1
3.2
3.3
3.4
68
3.6
3.5
AVDD − Supply Voltage − V
G028
Figure 32.
G029
Figure 33.
PERFORMANCE vs DRVDD
90
PERFORMANCE vs TEMPERATURE
77
fIN = 70.1 MHz
AVDD = 3.31 V
76
75
88
74
87
74
SFDR
86
73
85
72
SNR
84
71
83
70
3.1
3.2
3.3
3.4
DRVDD − Supply Voltage − V
Figure 34.
Submit Documentation Feedback
3.5
SNR − dBFS
75
SFDR − dBc
88
89
87
73
SFDR
86
72
SNR
85
71
84
SNR − dBFS
SINAD − dBFS
125
88
72
SFDR − dBc
100
Figure 31.
73
30
75
fIN − Input Frequency − MHz
Figure 30.
82
3.0
1 dB
0 dB
SNR − dBFS
82
89
3 dB
90
SFDR − dBc
90
SFDR − dBc
Input adjusted to get −1dBFS input
70
fIN = 70.1 MHz
69
3.6
83
−40
G030
69
−20
0
20
40
T − Temperature − °C
60
80
G031
Figure 35.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P24 (FS= 105 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
PERFORMANCE vs INPUT AMPLITUDE
PERFORMANCE vs CLOCK AMPLITUDE
90
94
77
92
90
80
90
80
75
70
70
SNR (dBFS)
60
65
50
SFDR (dBc)
40
30
−60
fIN = 20.1 MHz
−50
−40
−30
−20
−10
75
SFDR
74
86
73
84
72
SNR
82
71
55
80
70
50
78
0.0
0.5
1.0
1.5
2.0
2.5
Figure 37.
PERFORMANCE vs INPUT CLOCK DUTY CYCLE
OUTPUT NOISE HISTOGRAM WITH
INPUTS TIED TO COMMON-MODE
79
60
50
SFDR
76
86
75
84
74
82
73
80
72
SNR
78
40
30
20
10
71
76
Occurence − %
77
88
70
40
G033
78
90
35
69
3.0
Input Clock Amplitude − VPP
G032
Figure 36.
fIN = 20.1 MHz
30
76
88
0
94
92
fIN = 20.1 MHz
60
Input Amplitude − dBFS
SFDR − dBc
SFDR − dBc
85
SNR − dBFS
100
SNR − dBFS
SFDR − dBc, dBFS
SFDR (dBFS)
SNR − dBFS
110
45
50
55
60
65
0
70
Input Clock Duty Cycle − %
2040 2041 2042 2043 2044 2045 2046 2047 2048
Output Code
G034
Figure 38.
G035
Figure 39.
PERFORMANCE IN EXTERNAL REFERENCE MODE
95
79
fIN = 20.1 MHz
External Reference Mode
77
SFDR − dBc
SFDR
91
75
89
73
SNR − dBFS
93
SNR
87
85
1.35
71
1.40
1.45
1.50
1.55
VVCM − VCM Voltage − V
1.60
69
1.65
G036
Figure 40.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
31
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P23 (FS= 80 MSPS)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
FFT for 20 MHz INPUT SIGNAL
FFT for 70 MHz INPUT SIGNAL
0
0
SFDR = 89.61 dBc
SINAD = 71.22 dBFS
SNR = 71.44 dBFS
THD = 83.3 dBc
−20
−40
Amplitude − dB
Amplitude − dB
−40
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
40
f − Frequency − MHz
0
10
20
30
40
f − Frequency − MHz
G037
G038
Figure 41.
Figure 42.
FFT for 190 MHz INPUT SIGNAL
INTERMODULATION DISTORTION (IMD) vs FREQUENCY
0
0
SFDR = 84.12 dBc
SINAD = 70.22 dBFS
SNR = 70.45 dBFS
THD = 82.11 dBc
−20
fIN1 = 190.1 MHz, –7 dBFS
fIN2 = 185.3 MHz, –7 dBFS
2-Tone IMD = –93 dBFS
SFDR = –98 dBFS
−20
−40
Amplitude − dB
−40
Amplitude − dB
SFDR = 90.05 dBc
SINAD = 71.19 dBFS
SNR = 71.25 dBFS
THD = 89.09 dBc
−20
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
40
f − Frequency − MHz
0
10
20
30
40
f − Frequency − MHz
G039
Figure 43.
G040
Figure 44.
SFDR vs INPUT FREQUENCY
SNR vs INPUT FREQUENCY
98
74
96
73
Gain = 3.5 dB
92
SNR − dBFS
SFDR − dBc
94
90
88
86
72
Gain = 0 dB
71
70
Gain = 3.5 dB
Gain = 0 dB
84
69
82
80
68
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
Figure 45.
32
Submit Documentation Feedback
175
200
G041
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
175
200
G042
Figure 46.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P23 (FS= 80 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
SFDR vs INPUT FREQUENCY (LVDS interface)
SFDR vs INPUT FREQUENCY ACROSS GAIN
98
98
96
96
94
88
90
88
86
86
6 dB
Gain = 0 dB
84
84
82
82
80
80
1 dB
2 dB
0 dB
50
75
100
125
150
175
200
fIN − Input Frequency − MHz
0
25
50
75
G043
Figure 47.
SINAD vs INPUT FREQUENCY ACROSS GAIN
94
0 dB
1 dB
2 dB
200
G045
69
68
67
66
5 dB
6 dB
25
50
75
100
125
75
150
fIN − Input Frequency − MHz
175
90
74
88
73
86
200
72
SNR
84
71
82
70
80
3.0
65
0
76
SFDR
70
4 dB
77
fIN = 70.1 MHz
DRVDD = 3.31 V
92
3 dB
71
SFDR − dBc
SINAD − dBFS
175
PERFORMANCE vs AVDD
Input adjusted to get −1dBFS input
72
3.1
3.2
3.3
3.4
69
3.6
3.5
AVDD − Supply Voltage − V
G046
Figure 49.
G047
Figure 50.
PERFORMANCE vs DRVDD
96
PERFORMANCE vs TEMPERATURE
77
fIN = 70.1 MHz
AVDD = 3.31 V
92
76
76
fIN = 70.1 MHz
SFDR
90
75
90
74
SFDR
88
73
86
72
SNR
84
71
82
70
3.1
3.2
3.3
3.4
DRVDD − Supply Voltage − V
Figure 51.
Copyright © 2007–2008, Texas Instruments Incorporated
3.5
SNR − dBFS
75
SFDR − dBc
92
SFDR − dBc
150
96
73
80
3.0
125
Figure 48.
74
94
100
fIN − Input Frequency − MHz
SNR − dBFS
25
88
74
86
73
84
72
SNR − dBFS
0
3 dB
92
SFDR − dBc
90
5 dB
4 dB
94
Gain = 3.5 dB
92
SFDR − dBc
Input adjusted to get −1dBFS input
SNR
82
69
3.6
80
−40
G048
71
70
−20
0
20
40
60
80
T − Temperature − °C
G049
Figure 52.
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
33
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P23 (FS= 80 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
PERFORMANCE vs INPUT AMPLITUDE
PERFORMANCE vs CLOCK AMPLITUDE
90
80
92
80
90
75
SNR (dBFS)
76
75
SFDR
88
74
70
70
60
65
50
60
82
71
55
80
70
50
78
0.0
SFDR (dBc)
40
fIN = 20.1 MHz
30
−60
−50
−40
−30
−20
−10
73
SNR
84
1.0
1.5
2.0
2.5
Figure 54.
PERFORMANCE vs INPUT CLOCK DUTY CYCLE
OUTPUT NOISE HISTOGRAM WITH
INPUTS TIED TO COMMON-MODE
SFDR
90
78
90
77
80
76
70
75
88
74
86
73
84
72
SNR
Occurence − %
92
50
40
30
71
20
80
70
10
78
69
0
35
40
45
50
55
60
65
70
75
Input Clock Duty Cycle − %
G051
60
82
30
69
3.0
Input Clock Amplitude − VPP
G050
fIN = 20.1 MHz
25
0.5
72
Figure 53.
96
94
86
0
Input Amplitude − dBFS
SFDR − dBc
77
fIN = 20.1 MHz
SNR − dBFS
90
85
SNR − dBFS
SFDR − dBc, dBFS
100
SFDR − dBc
SFDR (dBFS)
94
SNR − dBFS
110
2040 2041 2042 2043 2044 2045 2046 2047 2048
Output Code
G052
Figure 55.
G053
Figure 56.
PERFORMANCE IN EXTERNAL REFERENCE MODE
92
80
fIN = 20.1 MHz
External Reference Mode
78
SFDR
88
76
86
74
84
82
1.35
72
SNR
1.40
1.45
SNR − dBFS
SFDR − dBc
90
1.50
1.55
VVCM − VCM Voltage − V
1.60
70
1.65
G054
Figure 57.
34
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P22 (FS= 65 MSPS)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
FFT for 20 MHz INPUT SIGNAL
FFT for 70 MHz INPUT SIGNAL
0
0
SFDR = 87.17 dBc
SINAD = 71.33 dBFS
SNR = 71.43 dBFS
THD = 86.73 dBc
−20
−40
Amplitude − dB
Amplitude − dB
−40
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
f − Frequency − MHz
0
10
20
30
f − Frequency − MHz
G055
G056
Figure 58.
Figure 59.
FFT for 190 MHz INPUT SIGNAL
INTERMODULATION DISTORTION (IMD) vs FREQUENCY
0
0
SFDR = 81.79 dBc
SINAD = 69.64 dBFS
SNR = 69.89 dBFS
THD = 81.28 dBc
−20
fIN1 = 190.1 MHz, –7 dBFS
fIN2 = 185.3 MHz, –7 dBFS
2-Tone IMD = –92 dBFS
SFDR = –94.5 dBFS
−20
−40
Amplitude − dB
−40
Amplitude − dB
SFDR = 87.71 dBc
SINAD = 71.21 dBFS
SNR = 71.29 dBFS
THD = 87.42 dBc
−20
−60
−80
−100
−60
−80
−100
−120
−120
−140
−140
−160
−160
0
10
20
30
f − Frequency − MHz
0
10
20
30
f − Frequency − MHz
G057
Figure 60.
G058
Figure 61.
SFDR vs INPUT FREQUENCY
SNR vs INPUT FREQUENCY
98
74
96
73
Gain = 3.5 dB
92
SNR − dBFS
SFDR − dBc
94
90
88
86
72
Gain = 0 dB
71
70
84
Gain = 0 dB
Gain = 3.5 dB
69
82
80
68
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
Figure 62.
Copyright © 2007–2008, Texas Instruments Incorporated
175
200
G059
0
25
50
75
100
125
150
175
fIN − Input Frequency − MHz
200
G060
Figure 63.
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
35
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P22 (FS= 65 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
SFDR vs INPUT FREQUENCY (LVDS interface)
SFDR vs INPUT FREQUENCY ACROSS GAIN
98
98
96
96
94
Gain = 3.5 dB
92
90
88
4 dB
5 dB
92
SFDR − dBc
SFDR − dBc
94
Input adjusted to get −1dBFS input
3 dB
90
88
86
86
6 dB
84
Gain = 0 dB
82
82
80
80
25
50
75
100
125
150
175
200
fIN − Input Frequency − MHz
0
25
50
G061
SINAD vs INPUT FREQUENCY ACROSS GAIN
Input adjusted to get −1dBFS input
0 dB
94
1 dB
175
200
G063
SFDR − dBc
70
69
4 dB
5 dB
6 dB
25
50
75
100
125
150
fIN − Input Frequency − MHz
75
175
90
74
88
73
86
200
71
82
70
3.1
3.2
PERFORMANCE vs DRVDD
fIN = 70.1 MHz
AVDD = 3.31 V
76
fIN = 70.1 MHz
91
75
SFDR
74
89
73
72
SNR
87
71
86
70
3.4
DRVDD − Supply Voltage − V
Figure 68.
Submit Documentation Feedback
3.5
SNR − dBFS
90
SFDR − dBc
75
SFDR
3.3
G065
92
76
3.2
69
3.6
3.5
PERFORMANCE vs TEMPERATURE
77
3.1
3.4
Figure 67.
93
88
3.3
AVDD − Supply Voltage − V
G064
Figure 66.
91
72
SNR
84
80
3.0
66
0
76
SFDR
3 dB
67
77
fIN = 70.1 MHz
DRVDD = 3.31 V
92
2 dB
71
SINAD − dBFS
150
PERFORMANCE vs AVDD
68
SFDR − dBc
125
96
72
36
100
Figure 65.
73
85
3.0
75
fIN − Input Frequency − MHz
Figure 64.
92
2 dB
1 dB
SNR − dBFS
0
0 dB
90
74
89
73
88
72
SNR
87
69
3.6
86
−40
G066
SNR − dBFS
84
71
70
−20
0
20
40
T − Temperature − °C
60
80
G067
Figure 69.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - ADS62P22 (FS= 65 MSPS) (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, maximum rated sampling frequency, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output
interface (unless otherwise noted)
PERFORMANCE vs INPUT AMPLITUDE
PERFORMANCE vs CLOCK AMPLITUDE
SFDR (dBFS)
85
92
80
75
70
70
60
65
50
SFDR (dBc)
40
−50
−40
−30
−20
−10
73
SNR
86
72
60
82
70
55
80
69
50
78
0.0
0.5
1.0
1.5
2.0
2.5
Figure 71.
PERFORMANCE vs INPUT CLOCK DUTY CYCLE
OUTPUT NOISE HISTOGRAM WITH
INPUTS TIED TO COMMON-MODE
fIN = 20.1 MHz
78
80
77
70
76
75
92
74
90
73
88
72
SNR
50
40
30
86
71
20
84
70
10
69
0
82
30
35
40
45
50
55
60
65
70
75
Input Clock Duty Cycle − %
G069
60
Occurence − %
SFDR
94
68
3.0
Input Clock Amplitude − VPP
G068
Figure 70.
96
SFDR − dBc
88
71
0
100
25
74
84
Input Amplitude − dBFS
98
75
SFDR
fIN = 20.1 MHz
fIN = 20.1 MHz
30
−60
76
90
SFDR − dBc
80
SNR (dBFS)
SNR − dBFS
90
94
SNR − dBFS
SFDR − dBc, dBFS
100
90
SNR − dBFS
110
2040 2041 2042 2043 2044 2045 2046 2047 2048 2049
Output Code
G070
Figure 72.
G071
Figure 73.
PERFORMANCE IN EXTERNAL REFERENCE MODE
95
80
fIN = 20.1 MHz
External Reference Mode
93
78
91
76
89
74
SNR
87
85
1.35
1.40
1.45
1.50
SNR − dBFS
SFDR − dBc
SFDR
72
1.55
VVCM − VCM Voltage − V
1.60
70
1.65
G072
Figure 74.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
37
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
TYPICAL CHARACTERISTICS - LOW SAMPLING FREQUENCIES
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sine wave input clock, 1.5 VPP differential clock amplitude, 50% clock duty
cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output interface (unless otherwise noted)
FS = 25 MSPS
SFDR vs INPUT FREQUENCY
SNR vs INPUT FREQUENCY
78
110
76
74
Gain = 3.5 dB
SNR − dBFS
SFDR − dBc
100
90
80
Gain = 0 dB
Gain = 0 dB
72
70
Gain = 3.5 dB
68
70
66
60
64
0
25
50
75
100
125
150
175
fIN − Input Frequency − MHz
200
0
25
50
75
100
125
150
fIN − Input Frequency − MHz
G075
Figure 75.
175
200
G076
Figure 76.
COMMON PLOTS
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sine wave input clock, 1.5 VPP differential clock amplitude, 50% clock duty
cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output interface (unless otherwise noted)
POWER DISSIPATION vs
SAMPLING FREQUENCY (DDR LVDS and CMOS)
COMMON-MODE REJECTION RATIO vs FREQUENCY
0.8
0.7
PD − Power Dissipation − W
0
−10
−20
CMRR − dBc
−30
−40
−50
−60
−70
−80
0.6
0.5
LVDS
0.4
0.3
CMOS
0.2
0.1
−90
0.0
−100
0
50
100
150
200
f − Frequency − MHz
Figure 77.
38
fIN = 2.5 MHz
CL = 5 pF
Submit Documentation Feedback
250
300
G077
0
25
50
75
100
fS − Sampling Frequency − MSPS
125
G078
Figure 78.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
COMMON PLOTS (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sine wave input clock, 1.5 VPP differential clock amplitude, 50% clock duty
cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, CMOS output interface (unless otherwise noted)
DRVDD current (CMOS interface) vs
SAMPLING FREQUENCY across load capacitance
30
1.8 V, No Load
DRVDD Current − mA
25
1.8 V, 5 pF
20
3.3 V, No Load
3.3 V, 5 pF
15
3.3 V, 10 pF
10
5
0
0
25
50
75
100
fS − Sampling Frequency − MSPS
125
G079
Figure 79.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
39
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
APPLICATION INFORMATION
THEORY OF OPERATION
ADS62P2X is a low power 12-bit dual channel pipeline ADC family fabricated in a CMOS process using switched
capacitor techniques.
The conversion process is initiated by a rising edge of the external input clock. Once the signal is captured by
the input sample and hold, the input sample is sequentially converted by a series of small resolution stages, with
the outputs combined in a digital correction logic block. At every clock edge the sample propagates through the
pipeline resulting in a data latency of 14 clock cycles. The output is available as 12-bit data, in DDR LVDS or
CMOS and coded in either straight offset binary or binary 2s complement format.
ANALOG INPUT
The analog input consists of a switched-capacitor based differential sample and hold architecture.
This differential topology results in very good AC performance even for high input frequencies at high sampling
rates. The INP and INM pins have to be externally biased around a common-mode voltage of 1.5 V, available on
VCM pin 13. For a full-scale differential input, each input pin INP, INM has to swing symmetrically between VCM
+ 0.5 V and VCM – 0.5 V, resulting in a 2 VPP differential input swing. The maximum swing is determined by the
internal reference voltages REFP (2.5 V nominal) and REFM (0.5 V, nominal).
Sampling
Switch
Lpkg
» 2 nH
Sampling
Capacitor
RCR Filter
INP
25 W
Cbond
» 1 pF
Resr
100 W
Cpar2
1 pF
50 W
3.2 pF
Ron
15 W
Cpar1
0.8 pF
Csamp
4 pF
Ron
10 W
50 W
Lpkg
» 2 nH
Ron
15 W
25 W
Csamp
4 pF
INM
Cbond
» 1 pF
Resr
100 W
Sampling
Capacitor
Cpar2
1 pF
Sampling
Switch
S0322-01
Figure 80. Analog Input Equivalent Circuit
The input sampling circuit has a high 3-dB bandwidth that extends up to 450 MHz (measured from the input pins
to the sampled voltage).
40
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
1
0
Magnitude − dB
−1
−2
−3
−4
−5
−6
−7
0
100
200
300
400
500
fI − Input Frequency − MHz
600
G080
Figure 81. ADC Analog Bandwidth
Drive Circuit Requirements
For optimum performance, the analog inputs must be driven differentially. This improves the common-mode
noise immunity and even order harmonic rejection. A < 5 Ω resistor in series with each input pin is recommended
to damp out ringing caused by the package parasitics.
It is also necessary to present low impedance (50 Ω) for the common mode switching currents. This can be
achieved by using two resistors from each input terminated to the common mode voltage (VCM).
In addition, the drive circuit may have to be designed to provide a low insertion loss over the desired frequency
range and matched impedance to the source. While doing this, the ADC input impedance must be considered.
Figure 82 and Figure 83 show the impedance (Zin = Rin || Cin) looking into the ADC input pins.
R − Resistance − kΩ
100
10
1
0.1
0.01
0
100
200
300
400
f − Frequency − MHz
500
600
G081
Figure 82. ADC Analog Input Resistance (Rin) Across Frequency
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
41
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
9
C − Capacitance − pF
8
7
6
5
4
3
2
1
0
0
100
200
300
400
500
f − Frequency − MHz
600
G082
Figure 83. ADC Analog Input Capacitance (Cin) Across Frequency
Using RF-Transformer Based Drive Circuits
Figure 84 shows a configuration using a single 1:1 turns ratio transformer (for example, Coilcraft WBC1-1) that
can be used for low input frequencies (about 100 MHz). The single-ended signal is fed to the primary winding of
the RF transformer. The transformer is terminated on the secondary side. Putting the termination on the
secondary side helps to shield the kickbacks caused by the sampling circuit from the RF transformer’s leakage
inductances. The termination is accomplished by two resistors connected in series, with the center point
connected to the 1.5 V common mode (VCM pin). The value of the termination resistors (connected to common
mode) has to be low ( < 100 Ω) to provide a low-impedance path for the ADC common-mode switching currents.
ADS62P2x
0.1 mF
INP
0.1 mF
25 W
25 W
INM
1:1
VCM
S0163-04
Figure 84. Drive Circuit at Low Input Frequencies
At high input frequencies, the mismatch in the transformer parasitic capacitance (between the windings) results
in degraded even-order harmonic performance. Connecting two identical RF transformers back-to-back helps
minimize this mismatch, and good performance is obtained for high frequency input signals. Figure 85 shows an
example using two transformers (Coilcraft WBC1-1). An additional termination resistor pair (enclosed within the
shaded box) may be required between the two transformers to improve the balance between the P and M sides.
The center point of this termination must be connected to ground.
42
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
ADS62P2x
0.1 mF
INP
50 W
0.1 mF
50 W
50 W
50 W
INM
1:1
1:1
VCM
S0164-07
Figure 85. Drive Circuit at High Input Frequencies
Using Differential Amplifier Drive Circuits
Figure 86 shows a drive circuit using a differential amplifier (TI's THS4509) to convert a single-ended input to
differential output that can be interface to the ADC analog input pins. In addition to the single-ended to differential
conversion, the amplifier also provides gain (10 dB). RFIL helps to isolate the amplifier outputs from the switching
input of the ADC. Together with CFIL it also forms a low-pass filter that band-limits the noise (and signal) at the
ADC input. As the amplifier output is ac-coupled, the common-mode voltage of the ADC input pins is set using
two 200 Ω resistors connected to VCM.
The amplifier output can also be dc-coupled. Using the output common-mode control of the THS4509, the ADC
input pins can be biased to 1.5 V. In this case, use +4 V and –1 V supplies for the THS4509 so that its output
common-mode voltage (1.5 V) is at mid-supply.
RF
+VS
500 W
0.1 mF
RS
0.1 mF 10 mF
RFIL
ADS62P2x
0.1 mF
5W
INP
RG
0.1 mF
RT
CFIL
200 W
CFIL
200 W
CM THS4509
RG
RFIL
INM
RS || RT
5W
0.1 mF
500 W
VCM
0.1 mF
–VS
0.1 mF 10 mF
0.1 mF
RF
S0259-04
Figure 86. Drive Circuit Using the THS4509
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
43
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Input Common-Mode
To ensure a low-noise common-mode reference, the VCM pin is filtered with a 0.1 µF low-inductance capacitor
connected to ground. The VCM pin is designed to directly drive the ADC inputs. The input stage of the ADC
sinks a common-mode current in the order of 165 µA (at 125 MSPS). Equation 1 describes the dependency of
the common-mode current and the sampling frequency.
165 mA Fs
125 MSPS
(1)
This equation helps to design the output capability and impedance of the CM driving circuit accordingly.
REFERENCE
ADS62P2X has built-in internal references REFP and REFM, requiring no external components. Design schemes
are used to linearize the converter load seen by the references; this and the on-chip integration of the requisite
reference capacitors eliminates the need for external decoupling. The full-scale input range of the converter can
be controlled in the external reference mode as explained below. The internal or external reference modes can
be selected by programming the serial interface register bit (REF).
INTREF
Internal
Reference
VCM
1 kW
INTREF
4 kW
EXTREF
REFM
REFP
ADS62P2x
S0165-07
Figure 87. Reference Section
Internal Reference
When the device is in internal reference mode, the REFP and REFM voltages are generated internally.
Common-mode voltage (1.5 V nominal) is output on VCM pin, which can be used to externally bias the analog
input pins.
External Reference
When the device is in external reference mode, the VCM acts as a reference input pin. The voltage forced on the
VCM pin is buffered and gained by 1.33 internally, generating the REFP and REFM voltages. The differential
input voltage corresponding to full-scale is given in Equation 2.
Full-scale differential input pp = (Voltage forced on VCM) × 1.33
44
Submit Documentation Feedback
(2)
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
In this mode, the 1.5 V common-mode voltage to bias the input pins has to be generated externally.
COARSE GAIN AND PROGRAMMABLE FINE GAIN
ADS62P2X includes gain settings that can be used to get improved SFDR performance (over 0 dB gain mode).
For each gain setting, the analog input full-scale range scales proportionally, as shown in Table 18.
The coarse gain is a fixed setting of 3.5 dB and is designed to improve SFDR with little degradation in SNR. The
fine gain is programmable in 0.5 dB steps from 0 to 6 dB; however the SFDR improvement is achieved at the
expense of SNR. So, the programmable fine gain makes it possible to trade-off between SFDR and SNR. The
coarse gain makes it possible to get best SFDR but without losing SNR significantly.
The gains can be programmed using the serial interface (bits COARSE GAIN and FINE GAIN). Note that the
default gain after reset is 0 dB.
Table 18. Full-Scale Range Across Gains
GAIN, dB
TYPE
0
Default after reset
FULL-SCALE, VPP
2V
3.5
Coarse (fixed)
1.34
0.5
1.89
1.0
1.78
1.5
1.68
2.0
1.59
2.5
1.50
3.0
3.5
Fine (programmable)
1.42
1.34
4.0
1.26
4.5
1.19
5.0
1.12
5.5
1.06
6.0
1.00
CLOCK INPUT
The clock inputs can be driven differentially (sine, LVPECL or LVDS) or single-ended (LVCMOS), with little or no
difference in performance between them. The common-mode voltage of the clock inputs is set to VCM using
internal 5 kΩ resistors as shown in Figure 88. This allows using transformer-coupled drive circuits for sine wave
clock or ac-coupling for LVPECL, LVDS clock sources (Figure 90 and Figure 91).
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
45
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Clock Buffer
Lpkg
» 2 nH
10 W
CLKP
Cbond
» 1 pF
Ceq
Ceq
5 kW
Resr
» 100 W
VCM
6 pF
5 kW
Lpkg
» 2 nH
10 W
CLKM
Cbond
» 1 pF
Resr
» 100 W
Ceq » 1 to 3 pF, equivalent input capacitance of clock buffer
S0275-02
Figure 88. Internal Clock Buffer
100k
Impedance − Ω
10k
1k
100
10
5
25
45
65
85
105
fS − Sampling Frequency − MSPS
125
G083
Figure 89. Clock Input Impedance
46
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
0.1 mF
CLKP
Differential Sine-Wave
or PECL or LVDS Clock Input
0.1 mF
CLKM
ADS62P2x
S0167-07
Figure 90. Differential Clock Driving Circuit
Single-ended CMOS clock can be ac-coupled to the CLKP input, with CLKM connected to ground with a 0.1-µF
capacitor, as shown in Figure 91.
0.1 mF
CMOS Clock Input
CLKP
0.1 mF
CLKM
ADS62P2x
S0168-11
Figure 91. Single-Ended Clock Driving Circuit
For best performance, the clock inputs have to be driven differentially, reducing susceptibility to common-mode
noise. For high input frequency sampling, it is recommended to use a clock source with very low jitter. Band-pass
filtering of the clock source can help reduce the effect of jitter. There is no change in performance with a
non-50% duty cycle clock input.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
47
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
POWER DOWN
ADS62P2X has three powerdown modes – powerdown global, individual channel standby and individual channel
output buffer disable. These can be set using either the serial register bits or using the control pins CTRL1 to
CTRL3.
Table 19. Power Down Modes
CONFIGURE USING
POWERDOWN MODES
SERIAL INTERFACE
<POWER DOWN MODES>
PARALLEL CONTROL PINS
CTRL1
CTRL2
WAKE-UP
TIME
CTRL3
Normal operation
000
low
low
low
—
Channel A output buffer disabled
001
low
low
high
Fast (100 ns)
Channel B output buffer disabled
010
low
high
low
Fast (100 ns)
Channel A and B output buffer disabled
011
low
high
high
Fast (100 ns)
Channel A and B powered down
100
high
low
low
Slow (15 µS)
Channel A standby
101
high
low
high
Fast (100 ns)
Channel B standby
110
high
high
low
Fast (100 ns)
Multiplexed (MUX) mode – Output data of
channel A and B is multiplexed and available
on DA13 to DA0 pins.
111
high
high
high
—
PowerDown Global
In this mode, the entire chip including both the A/D converters, internal reference and the output buffers are
powered down resulting in reduced total power dissipation of about 50 mW. The output buffers are in high
impedance state. The wake-up time from the global power down to data becoming valid in normal mode is
typically 15 µs.
Channel Standby (Individual or Both Channels)
This mode allows the individual ADCs to be powered down. The internal references are active and this results in
fast wake-up time, about 100 ns. The total power dissipation in standby is about 482 mW.
Output Buffer Disable (Individual or Both Channels)
Each channel’s output buffer can be disabled and put in high impedance state -- wakeup time from this mode is
fast, about 100 ns.
Input Clock Stop
In addition to the above, the converter enters a low-power mode when the input clock frequency falls below 1
MSPS. The power dissipation is about 140 mW.
POWER SUPPLY SEQUENCE
During power-up, the AVDD and DRVDD supplies can come up in any sequence. The two supplies are
separated in the device. Externally, they can be driven from separate supplies or derived from a single supply.
48
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DIGITAL OUTPUT INFORMATION
ADS62P2X provides 12 bit data per channel and a common output clock synchronized with the data. The output
interface can be either parallel CMOS or DDR LVDS voltage levels and can be selected using serial register bit
<OUTPUT INTERFACE> or parallel pin SEN.
Parallel CMOS Interface
In the CMOS mode, the output buffer supply (DRVDD) can be operated over a wide range from 1.8 V to 3.3 V
(typical). Each data bit is output on separate pin as CMOS voltage level, every clock cycle (see Figure 92).
For DRVDD > 2.2 V, it is recommended to use the CMOS output clock (CLKOUT) to latch data in the receiving
chip. The rising edge of CLKOUT can be used to latch data in the receiver, even at the highest sampling speed.
It is recommended to minimize the load capacitance seen by data and clock output pins by using short traces to
the receiver. Also, match the output data and clock traces to minimize the skew between them.
For DRVDD < 2.2 V, it is recommended to use external clock (for example, input clock delayed to get desired
setup/hold times).
CMOS
Output Buffers
DA0
DA1
DA2
12-Bit Channel-A
Data
DA3
·
·
·
DA10
DA11
CLKOUT
DB0
DB1
DB2
12-Bit Channel-B
Data
DB3
·
·
·
DB10
DB11
B0287-02
Figure 92. CMOS Output Interface
Output Buffer Strength Programmability
Switching noise (caused by CMOS output data transitions) can couple into the analog inputs during the instant of
sampling and degrade the SNR. The coupling and SNR degradation increases as the output buffer drive is made
stronger. To minimize this, ADS62P2X CMOS output buffers are designed with controlled drive strength to get
best SNR. The default drive strength also ensures wide data stable window for load capacitances up to 5 pF and
DRVDD supply voltage > 2.2 V.
To ensure wide data stable window for load capacitance > 5 pF, there exists option to increase the output data
and clock drive strengths using the serial interface ( DATAOUT STRENGTH and CLKOUT STRENGTH). Note
that for DRVDD supply voltage < 2.2 V, it is recommended to use maximum drive strength (for any value of load
capacitance).
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
49
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
CMOS Mode Power Dissipation
With CMOS outputs, the DRVDD current scales with the sampling frequency and the load capacitance on every
output pin. The maximum DRVDD current occurs when each output bit toggles between 0 and 1 every clock
cycle. In actual applications, this condition is unlikely to occur. The actual DRVDD current would be determined
by the average number of output bits switching, which is a function of the sampling frequency and the nature of
the analog input signal.
Digital current due to CMOS output switching = CL × DRVDD × (N × FAVG),
where CL = load capacitance, N × FAVG = average number of output bits switching.
Figure 79 shows the current with various load capacitances across sampling frequencies at 2 MHz analog input
frequency.
DDR LVDS Interface
The LVDS interface works only with 3.3 V DRVDD supply. In this mode, the 12 data bits of each channel and a
common output clock are available as LVDS (Low Voltage Differential Signal) levels. Two successive data bits
are multiplexed and output on each LVDS differential pair every clock cycle (DDR – Double Data Rate,
Figure 94).
LVDS Buffers
12-Bit Channel-A
Data
Pins
DA0P
DA0M
Data Bits D0, D1
DA2P
DA2M
Data Bits D2, D3
·
·
·
·
·
·
DA10P
DA10M
12-Bit Channel-B
Data
Data Bits D10, D11
CLKOUTP
CLKOUTM
Output Clock
DB0P
DB0M
Data Bits D0, D1
DB2P
DB2M
Data Bits D2, D3
·
·
·
·
·
·
DB10P
DB10M
Data Bits D10, D11
B0288-02
Figure 93. DDR LVDS Outputs
Even data bits D0, D2, D4, D6, D8, D10 are output at the rising edge of CLKOUTP and odd data bits D1, D3,
D5, D7, D9, D11 are output at the falling edge of CLKOUTP. Both the rising and falling edges of CLKOUTP have
to be used to capture all the data bits.
50
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
CLKOUTM
CLKOUTP
DA0 (DB0)
D0
D1
D0
D1
DA2 (DB2)
D2
D3
D2
D3
DA4 (DB4)
D4
D5
D4
D5
DA6 (DB6)
D6
D7
D6
D7
DA8 (DB8)
D8
D9
D8
D9
DA10 (DB10)
D10
D11
D10
D11
Sample N
Sample N+1
T0110-03
Figure 94. DDR LVDS Interface
LVDS Buffer Current Programmability
The default LVDS buffer output current is 3.5 mA. When terminated by 100 Ω, this results in a 350-mV
single-ended voltage swing (700-mVPP differential swing). The LVDS buffer currents can also be programmed to
2.5 mA, 4.5 mA, and 1.75 mA (LVDS CURRENT). In addition, there exists a current double mode, where this
current is doubled for the data and output clock buffers (register bits CURRENT DOUBLE).
LVDS Buffer Internal Termination
An internal termination option is available (using the serial interface), by which the LVDS buffers are differentially
terminated inside the device. The termination resistances available are – 300 Ω, 185 Ω, and 150 Ω (nominal with
±20% variation). Any combination of these three terminations can be programmed; the effective termination is
the parallel combination of the selected resistances. This results in eight effective terminations from open (no
termination) to 60 Ω.
The internal termination helps to absorb any reflections coming from the receiver end, improving the signal
integrity. With 100 Ω internal and 100 Ω external termination, the voltage swing at the receiver end is halved
(compared to no internal termination). The voltage swing can be restored by using the LVDS current double
mode. Figure 95 and Figure 96 compare the LVDS eye diagrams without and with 100 Ω internal termination.
With internal termination, the eye looks clean even with 10 pF load capacitance (from each output pin to ground).
The terminations can be programmed using register bits (LVDS TERMINATION).
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
51
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Figure 95. LVDS Eye Diagram – No Internal Termination, External Termination = 100 Ω
Figure 96. LVDS Eye Diagram – With 100 Ω Internal Termination, External termination = 100 Ω and LVDS
current Double Mode Enabled
52
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Output Data Format
Two output data formats are supported – 2s complement and straight binary. They can be selected using the
serial interface register bit <DATA FORMAT> or controlling the SEN pin in parallel configuration mode.
In the event of an input voltage overdrive, the digital outputs go to the appropriate full scale level. For a positive
overdrive, the output code is 0x7FF in offset binary output format, and 0x3FF in 2s complement output format.
For a negative input overdrive, the output code is 0x000 in offset binary output format and 0x400 in 2s
complement output format.
Multiplexed Output mode
This mode is available only with CMOS interface. In this mode, the digital outputs of both the channels are
multiplexed and output on a single bus (DB0 - DB11 pins), as per the timing diagram shown in Figure 97. The
channel A output pins (DA0 - DA11) are three-stated. Since the output data rate on the DB bus is effectively
doubled, this mode is recommended only for low sampling frequencies (< 65 MSPS).
This mode can be enabled using register bits <POWERDOWN MODES> or using the parallel pins CTRL1,
CTRL2, and CTRL3.
CLKOUT
DB0
DA0
DB0
DA0
DB0
DB1
DA1
DB1
DA1
DB1
DB2
DA2
DB2
DA2
DB2
DB11
DA11
DB11
DA11
DB11
Sample N
Sample N+1
T0297-02
Figure 97. Multiplexed Mode – Output Timing
Low Latency Mode
The default latency of ADS62P2X is 14 clock cycles. For applications, which cannot tolerate large latency,
ADS62P2X includes a special mode with 10 clock cycles latency. In the low latency condition, the Digital
Processing block is bypassed and its features (offset correction, fine gain, decimation filters) are not available.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
53
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DETAILS OF DIGITAL PROCESSING BLOCK
CLIPPER
From
ADC
Output
12 Bits
12 Bits
12 Bits
12 Bits
12 Bits
To output buffers
LVDS or CMOS
Fine Gain
(0 to 6 dB
0.05 dB Steps)
24 TAP FILTER
- LOW PASS
- HIGH PASS
- BAND PASS
Gain Correction
(0.05 dB Steps)
DECIMATION
BY 2/4/8
12 Bits
0
OFFSET
ESTIMATION
BLOCK
Filter Select
Disable
Offset
Correction
Freeze Offset
Correction
OFFSET
CORRECTION
Bypass
Filter
Bypass
Decimation
FINE GAIN
DIGITAL
FILTER and DECIMATION
GAIN
CORRECTION
DIGITAL PROCESSING BLOCK
B0289-02
Figure 98. Digital Processing Block Diagram
Offset Correction
ADS62P2X has an internal offset correction algorithm that estimates and corrects dc offset up to ±10 mV. The
correction can be enabled using the serial register bit (OFFSET LOOP EN). Once enabled, the algorithm
estimates the channel offset and applies the correction every clock cycle. The time constant of the correction
loop is a function of the sampling clock frequency. The time constant can be controlled using register bits
(OFFSET LOOP TC) as described in Table 20.
Table 20. Time Constant of Offset Correction Algorithm
(1)
<OFFSET LOOP TC>
D6-D5-D4
TIME CONSTANT (TCCLK),
Number of clock cycles
TIME CONSTANT, sec
(= TCCLK × 1/Fs) (1)
000
227
1.1
001
26
2
0.55
010
225
0.27
011
224
0.13
100
228
2.15
101
29
2
4.3
110
227
1.1
111
227
1.1
Sampling frequency, Fs = 125 MSPS
It is also possible to freeze the offset correction using the serial interface (<OFFSET LOOP FREEZE>). Once
frozen, the offset estimation becomes inactive and the last estimated value is used for correction every clock
cycle. Note that the offset correction is disabled by default after reset.
Figure 99 shows the time response of the offset correction algorithm, after it is enabled (for clarity, an example
with no applied input signal is shown). A few time constants after the correction is enabled, the offset gets
cancelled and the output code approaches the ideal value of 2048.
54
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
2065
2060
Device With
Offset Cancelled
Code − LSB
2055
2050
2045
Offset Loop
Enabled Here
2040
Device With
Initial Offset
2035
2030
0
2
4
6
8
10
12
t − Time − s
14
G084
Figure 99. Time Response of Offset Correction
Gain Correction
ADS62P2X has ability to make fine corrections to the ADC channel gain. The corrections can be done in steps of
0.05 dB, up to a maximum of 0.5 dB, using the register bits (GAIN CORRECTION). Only positive corrections are
supported and the same correction applies to both the channels.
Table 21. Gain Correction Values
<GAIN CORRECTION>
D3-D2-D1-D0
AMOUNT OF CORRECTION,
dB
0000
0
0001
+0.05
0010
+0.1
0011
+0.15
0100
+0.20
0101
+0.25
0110
+0.30
0111
+0.35
1000
+0.40
1001
+0.45
1010
+0.5
Other combinations
Unused
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
55
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Decimation Filters
ADS62P2X includes option to decimate the ADC output data with in-built low-pass, high-pass, or band-pass
filters.
The decimation rate and type of filter can be selected using register bits (DECIMATION RATE) and
(DECIMATION FILTER TYPE). Decimation rates of 2, 4, or 8 are available and either low-pass, high-pass, or
band-pass filters can be selected (see Table 22). By default, the decimation filter is disabled – use register bit
<FILTER ENABLE> to enable it.
Table 22. Decimation Filter Modes
COMBINATION OF DECIMATION RATES AND FILTER TYPES
DECIMATION
<DECIMATION
RATE>
TYPE OF FILTER
Decimate by 2
<DECIMATIO
N FILTER
FREQ
BAND>
<FILTER
COEFF
SELECT
>
<FILTER
ENABLE>
In-built low-pass filter (pass band = 0 to Fs/4)
0
0
0
0
0
0
1
In-built high-pass filter (pass band = Fs/4 to Fs/2)
0
0
0
0
1
0
1
In-built low-pass filter (pass band = 0 to Fs/8)
0
0
1
0
0
0
1
In-built 2nd band-pass filter (pass band = Fs/8 to Fs/4)
0
0
1
0
1
0
1
In-built 3 band-pass filter (pass band = Fs/4 to 3Fs/8)
0
0
1
1
0
0
1
In-built last band-pass filter (pass band = 3Fs/8 to Fs/2)
0
0
1
1
1
0
1
Decimate by 2
Custom filter (user programmable coefficients)
0
0
0
X
X
1
1
Decimate by 4
Custom filter (user programmable coefficients)
0
0
1
X
X
1
1
Decimate by 8
Custom filter (user programmable coefficients)
1
0
0
X
X
1
1
NO decimation
Custom filter (user programmable coefficients)
0
1
1
X
X
1
0
Decimate by 4
rd
Decimation Filter Equation
The decimation filter is implemented as 24-tap FIR with symmetrical coefficients (each coefficient is 12-bit
signed). The filter equation is:
y(n) +
ǒ21 Ǔ
[h0
11
x(n) ) h1
x(n * 1) ) h2
x(n * 2) ) AAA ) h11
x(n * 11) ) h11
x(n * 12) ) AAA ) h1
x(n * 22) ) h0
x(n * 23)]
(3)
By setting the register bit <ODD TAP ENABLE> = 1, a 23-tap FIR is implemented:
y(n) +
ǒ21 Ǔx[h0
11
x(n) ) h1
x(n * 1) ) h2
x(n * 2) ) AAA ) h10
x(n * 10) ) h11
x(n * 11) ) h10
x(n * 12) ) AAA ) h1
x(n * 21) ) h0
x(n * 22)]
(4)
In the above equations,
h0, h1 …h11 are 12-bit signed representation of the coefficients,
x(n) is the input data sequence to the filter
y(n) is the filter output sequence
Pre-defined Coefficients
The in-built filter types (low-pass, high-pass, and band-pass) use pre-defined coefficients. The frequency
response of the in-built filters is shown in Figure 100 and Figure 101.
56
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
5
0
Magnitude − dB
−5
−10
Low Pass
High Pass
−15
−20
−25
−30
−35
−40
−45
0.0
0.1
0.2
0.3
0.4
0.5
Normalized Frequency − f/fS
G085
Figure 100. Decimate by 2 Filter Response
5
0
Magnitude − dB
−5
−10
Low Pass
High Pass
−15
−20
−25
−30
−35
−40
−45
0.0
0.1
0.2
0.3
0.4
0.5
Normalized Frequency − f/fS
G086
Figure 101. Decimate by 4 Filter Response
5
0
Magnitude − dB
−5
−10
−15
−20
−25
−30
−35
−40
−45
0.0
1st Bandpass
2nd Bandpass
0.1
0.2
0.3
Normalized Frequency − f/fS
0.4
0.5
G087
Figure 102. Decimate by 4 Band-Pass Response
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
57
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Table 23. Predefined Coefficients for Decimation by 2 Filters
COEFFICIENTS
DECIMATE BY 2
LOW-PASS FILTER
HIGH-PASS FILTER
h0
23
-22
h1
-37
-65
h2
-6
-52
h3
68
30
h4
-36
66
h5
-61
-35
h6
35
-107
h7
118
38
h8
-100
202
h9
-197
-41
h10
273
-644
h11
943
1061
Table 24. Predefined Coefficients for Decimation by 4 Filters
COEFFICIENTS
DECIMATE BY 4
LOW-PASS FILTER
1st BAND-PASS FILTER
2ND BAND-PASS FILTER
h0
-17
-7
-34
HIGH-PASS FILTER
32
h1
-50
19
-34
-15
h2
71
-47
-101
-95
h3
46
127
43
22
h4
24
73
58
-8
h5
-42
0
-28
-81
h6
-100
86
-5
106
h7
-97
117
-179
-62
h8
8
-190
294
-97
h9
202
-464
86
310
h10
414
-113
-563
-501
h11
554
526
352
575
Custom Filter Coefficients with Decimation
The filter coefficients can also be programmed by the user (custom). For custom coefficients, set the register bit
(FILTER COEFF SELECT) and load the coefficients (h0 to h11) in registers 1E to 2F using the serial interface
(Table 25) as:
Register content = 12 bit signed representation of [real coefficient value × 211]
58
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Custom Filter Coefficients without Decimation
The filter with custom coefficients can also be used with the decimation mode disabled. In this mode, the filter
implementation is 12-tap FIR:
y(n) +
ǒ21 Ǔx[h6
11
x(n) ) h7
x(n * 1) ) h8
x(n * 2) ) AAA ) h11
x(n * 5) ) h11
x(n * 6) ) AAA ) h7
x(n * 10) ) h6
x(n * 11)]
(5)
Table 25. Register Map of Custom Coefficients
A7–A0
(hex)
D7
D6
D5
1E
1F
Coefficient h2 <7:0>
Coefficient h2 <11:8>
Coefficient h3 <11:4>
Coefficient h4 <7:0>
Coefficient h5 <3:0>
26
Coefficient h4 <11:8>
Coefficient h5 <11:4>
27
Coefficient h6 <7:0>
Coefficient h7 <3:0>
29
Coefficient h6 <11:8>
Coefficient h7 <11:4>
2A
Coefficient h8 <7:0>
Coefficient h9 <3:0>
2C
Coefficient h8 <11:8>
Coefficient h9 <11:4>
2D
2E
D0
Coefficient h0 <11:8>
Coefficient h3 <3:0>
24
2B
D1
Coefficient h1 <11:4>
23
28
D2
Coefficient h0 <7:0>
21
25
D3
Coefficient h1 <3:0>
20
22
D4
Coefficient h10 <7:0>
Coefficient h11 <3:0>
2F
Coefficient h10 <11:8>
Coefficient h11 <11:4>
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
59
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
BOARD DESIGN CONSIDERATIONS
Grounding
A single ground plane is sufficient to give good performance, provided the analog, digital, and clock sections of
the board are cleanly partitioned. See the EVM User Guide (SLAU237) for details on layout and grounding.
Supply Decoupling
As ADS62P2X already includes internal decoupling, minimal external decoupling can be used without loss in
performance. Note that decoupling capacitors can help filter external power supply noise, so the optimum
number of capacitors would depend on the actual application. The decoupling capacitors should be placed very
close to the converter supply pins.
It is recommended to use separate supplies for the analog and digital supply pins to isolate digital switching
noise from sensitive analog circuitry. In case only a single 3.3-V supply is available, it should be routed first to
AVDD. It can then be tapped and isolated with a ferrite bead (or inductor) with decoupling capacitor, before being
routed to DRVDD.
Exposed Thermal Pad
It is necessary to solder the exposed pad at the bottom of the package to a ground plane for best thermal
performance. For detailed information, see application notes QFN Layout Guidelines (SLOA122) and QFN/SON
PCB Attachment (SLUA271).
60
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
DEFINITION OF SPECIFICATIONS
Analog Bandwidth
The analog input frequency at which the power of the fundamental is reduced by 3 dB with respect to the low
frequency value.
Aperture Delay
The delay in time between the rising edge of the input sampling clock and the actual time at which the sampling
occurs.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Clock Pulse Width/Duty Cycle
The duty cycle of a clock signal is the ratio of the time the clock signal remains at a logic high (clock pulse width)
to the period of the clock signal. Duty cycle is typically expressed as a percentage. A perfect differential
sine-wave clock results in a 50% duty cycle.
Maximum Conversion Rate
The maximum sampling rate at which certified operation is given. All parametric testing is performed at this
sampling rate unless otherwise noted.
Minimum Conversion Rate
The minimum sampling rate at which the ADC functions.
Differential Nonlinearity (DNL)
An ideal ADC exhibits code transitions at analog input values spaced exactly 1 LSB apart. The DNL is the
deviation of any single step from this ideal value, measured in units of LSBs
Integral Nonlinearity (INL)
The INL is the deviation of the ADC’s transfer function from a best fit line determined by a least squares curve fit
of that transfer function, measured in units of LSBs.
Gain Error
Gain error is the deviation of the ADC's actual input full-scale range from its ideal value. The gain error is given
as a percentage of the ideal input full-scale range. Gain error has two components: error due to reference
inaccuracy and error due to the channel. Both these errors are specified independently as EGREF and EGCHAN.
To a first order approximation, the total gain error will be ETOTAL ~ EGREF + EGCHAN
For example, if ETOTAL = ±0.5%, the full-scale input varies from (1-0.5/100) x FSideal to (1+0.5/100) x FSideal.
Offset Error
The offset error is the difference, given in number of LSBs, between the ADC’s actual average idle channel
output code and the ideal average idle channel output code. This quantity is often mapped into mV.
Temperature Drift
The temperature drift coefficient (with respect to gain error and offset error) specifies the change per degree
Celsius of the parameter from TMIN to TMAX. It is calculated by dividing the maximum deviation of the parameter
across the TMIN to TMAX range by the difference TMAX–TMIN.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
61
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
Signal-to-Noise Ratio
SNR is the ratio of the power of the fundamental (PS) to the noise floor power (PN), excluding the power at dc
and the first nine harmonics.
P
SNR + 10Log 10 s
PN
(6)
SNR is either given in units of dBc (dB to carrier) when the absolute power of the fundamental is used as the
reference, or dBFS (dB to full scale) when the power of the fundamental is extrapolated to the converter’s
full-scale range.
Signal-to-Noise and Distortion (SINAD)
SINAD is the ratio of the power of the fundamental (PS) to the power of all the other spectral components
including noise (PN) and distortion (PD), but excluding dc.
Ps
SINAD + 10Log 10
PN ) PD
(7)
SINAD is either given in units of dBc (dB to carrier) when the absolute power of the fundamental is used as the
reference, or dBFS (dB to full scale) when the power of the fundamental is extrapolated to the converter’s
full-scale range.
Effective Number of Bits (ENOB)
The ENOB is a measure of a converter’s performance as compared to the theoretical limit based on quantization
noise.
ENOB + SINAD * 1.76
6.02
(8)
Total Harmonic Distortion (THD)
THD is the ratio of the power of the fundamental (PS) to the power of the first nine harmonics (PD).
P
THD + 10Log 10 s
PN
(9)
THD is typically given in units of dBc (dB to carrier).
Spurious-Free Dynamic Range (SFDR)
The ratio of the power of the fundamental to the highest other spectral component (either spur or harmonic).
SFDR is typically given in units of dBc (dB to carrier).
Two-Tone Intermodulation Distortion
IMD3 is the ratio of the power of the fundamental (at frequencies f1 and f2) to the power of the worst spectral
component at either frequency 2f1–f2 or 2f2–f1. IMD3 is either given in units of dBc (dB to carrier) when the
absolute power of the fundamental is used as the reference, or dBFS (dB to full scale) when the power of the
fundamental is extrapolated to the converter’s full-scale range.
DC Power Supply Rejection Ratio (DC PSRR)
The DC PSSR is the ratio of the change in offset error to a change in analog supply voltage. The DC PSRR is
typically given in units of mV/V.
62
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
ADS62P25, ADS62P24
ADS62P23, ADS62P22
www.ti.com
SLAS576A – OCTOBER 2007 – REVISED FEBRUARY 2008
AC Power Supply Rejection Ratio (AC PSRR)
AC PSRR is the measure of rejection of variations in the supply voltage of the ADC. If ΔVSUP is the change in the
supply voltage and ΔVOUT is the resultant change in the ADC output code (referred to the input), then
DVOUT
(Expressed in dBc)
PSRR = 20Log 10
DVSUP
(10)
Common Mode Rejection Ratio (CMRR)
CMRR is the measure of rejection of variations in the input common-mode voltage of the ADC. If ΔVcm is the
change in the input common-mode voltage and ΔVOUT is the resultant change in the ADC output code (referred
to the input), then
DVOUT
(Expressed in dBc)
CMRR = 20Log10
DVCM
(11)
Voltage Overload Recovery
The number of clock cycles taken to recover to less than 1% error for a 6-dB overload on the analog inputs. A
6-dBFS sine wave at Nyquist frequency is used as the test stimulus.
Copyright © 2007–2008, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ADS62P25, ADS62P24 ADS62P23, ADS62P22
63
PACKAGE OPTION ADDENDUM
www.ti.com
20-Mar-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
ADS62P22IRGCR
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P22IRGCRG4
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P22IRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P22IRGCTG4
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P23IRGCR
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P23IRGCRG4
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P23IRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P23IRGCTG4
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P24IRGCR
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P24IRGCRG4
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P24IRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P24IRGCTG4
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P25IRGCR
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P25IRGCRG4
ACTIVE
VQFN
RGC
64
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P25IRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ADS62P25IRGCTG4
ACTIVE
VQFN
RGC
64
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
20-Mar-2008
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jul-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
ADS62P22IRGCR
VQFN
RGC
64
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P22IRGCT
VQFN
RGC
64
250
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P23IRGCR
VQFN
RGC
64
2500
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P23IRGCT
VQFN
RGC
64
250
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P24IRGCR
VQFN
RGC
64
2500
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P24IRGCT
VQFN
RGC
64
250
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P25IRGCR
VQFN
RGC
64
2500
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS62P25IRGCT
VQFN
RGC
64
250
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jul-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS62P22IRGCR
VQFN
RGC
64
2500
333.2
345.9
28.6
ADS62P22IRGCT
VQFN
RGC
64
250
333.2
345.9
28.6
ADS62P23IRGCR
VQFN
RGC
64
2500
333.2
345.9
28.6
ADS62P23IRGCT
VQFN
RGC
64
250
333.2
345.9
28.6
ADS62P24IRGCR
VQFN
RGC
64
2500
333.2
345.9
28.6
ADS62P24IRGCT
VQFN
RGC
64
250
333.2
345.9
28.6
ADS62P25IRGCR
VQFN
RGC
64
2500
333.2
345.9
28.6
ADS62P25IRGCT
VQFN
RGC
64
250
333.2
345.9
28.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
Similar pages