TB2132FNG TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic TB2132FNG 3-V AM/FM/TV Single Chip Tuner IC with On-Chip PLL The TB2132FNG is an IC suitable for 3-V headphone radio and radio cassette application. It has FM/TV front end, FM IF, FM stereo decoder, AM function and PLL function on a single chip. The FM/TV front end is designed to lower the oscillation voltage of the FM/TV local oscillator, enabling this IC to meet the new FCC standards. Features • Low supply current (VCC = 3 V, Ta = 25°C) Weight: 0.17 g (typ.) FM: ICC = 18 mA (typ.) AM: ICC = 7.5 mA (typ.) • Operating supply voltage range : VCC = 1.8 to 5.5 V (Ta = 25°C) • Tuner block • Can be used for TV band. • Enable to meet the new FCC standards. • Adjustment-free FM quad detector due to ceramic discriminator • On-chip FM MPX VCO circuit • PLL block • Reference frequency: 1 kHz , 1.5625 kHz, 3 kHz, 3.125 kHz, 5 kHz, 6.25 kHz, 12.5 kHz, 25 kHz • Data transfer is performed with synchronous three-line bus, using pins CE (Chip Enable), CK (Clock) and DATA (DATA). • Crystal oscillation frequency: 75 kHz • IF count method: On-chip 20-bit counter Note: The TB2132FNG is mounted with lead-free soldering alloys. Pin 26 (FM/TV OSC) is sensitive to electrostatic discharge. Take care when handling. 1 2004-05-07 TB2132FNG Block Diagram FM TV RFout RFout 30 29 RF VCC AM FM/TV AM RFin OSC OSC 28 27 26 25 OSC AM OSC AM MIX CK DATA PLL VCC Do 24 23 22 21 20 AM 1/2 TV1/8 1/4 BUFF 1/16 FM1/32 FM/TV1/2 AM FM TV RF IF BUFF FM/TV MIX FM RF OUT2 OUT1 (DO2) (ST) 19 18 PLL GND XI 17 16 AMOSCin Program PC counter FMOSCin Reference IFin PLL divider 1/8 FM/AM/TV SW INV FM MPX FM DET AM DET FM IF AGC 1 CE 2 FM/TV GND RF in 3 4 5 6 7 MIX out AGC FM IFin VCC AM IFin MUTE AF AM IF 8 9 QUAD DET out 2 10 11 12 13 14 15 MPX in LPF1 LPF2 L-ch R-ch XO 2004-05-07 TB2132FNG Pin Description 1. Tuner Block Pin No. Characteristics Pin Voltage (typ.) (V) AM FM Internal Circuit 30 1 29 FM/TV RFin 0 0.8 0 0 3.0 3.0 0 0 3.0 3.0 3.0 3.0 1 kΩ 1 kΩ 1 GND 2 2 ⎯ GND VCC 6 3 FM MIX 3 MIX OUT AM MIX 2 GND RF GND 2 6 4 AGC 2 VCC 6 5 FM IF IN 330 Ω 4 5 GND 2 6 VCC (VCC for FM IF and MPX) ⎯ 3 2004-05-07 TB2132FNG Pin Voltage (typ.) (V) AM FM Internal Circuit 3 kΩ Characteristics 7 3 kΩ Pin No. 7 AM IF IN 2.3 2.5 2.5 2.2 1.0 0.9 0.7 0.7 GND 2 8 VCC 6 8 QUOD GND 2 VCC 6 AM 9 FM DET OUT 750 Ω 9 GND 2 55 kΩ 10 10 MPX IN GND 2 4 2004-05-07 TB2132FNG Pin No. Characteristics Pin Voltage (typ.) (V) AM FM Internal Circuit 11 DC AMP 11 LPF1 • LPF pin for synchronous detector 0.7 2.4 0 2.2 1.2 1.2 3.0 3.0 2 GND 12 12 LPF2 • LPF pin for phase detector 2 GND VCC 6 L-OUT R-OUT 5 kΩ 13 14 13, 14 GND 2 25 VCC 6 25 AM OSC GND 2 5 2004-05-07 TB2132FNG Pin No. Characteristics Internal Circuit Pin Voltage (typ.) (V) AM FM 26 RF VCC 28 26 FM/TV OSC 3.0 3.0 3.0 3.0 3.0 3.0 GND 2 VCC 6 AGC 27 AM RFin 27 GND 2 28 ⎯ RF VCC (VCC for FM RF) 29 TV RF OUT Refer to the internal circuit of pin 1. 3.0 3.0 30 FM RFout Refer to the internal circuit of pin 1. 3.0 3.0 6 2004-05-07 TB2132FNG 2. PLL Block Pin No. 15 Symbol Pin Name Description Equivalent Circuit XOUT Crystal oscillator pin 16 XIN 17 PLL GND These pins are used for a crystal oscillator. XIN 16 A 75-kHz reference crystal oscillator is connected to the pins XIN and XOUT. 15 XOUT Power supply input pin This is a power supply input pin for the PLL block. 17 This port can be switched between general-purpose output port and ST output using STC bit of serial data. 18 OUT1 (ST) General-purpose output port (ST port) Note: Upon power-on or power-on reset, pin 18 is configured as an output (the OUT1 output will be low). Thus, If an LED is connected to pin 18 for stereo display, it is illuminated at these times. VDD 18 VDD 19 OUT2 (DO2) General-purpose output port (DO output) This port can be switched between general-purpose output port and DO output using DO2 bit of serial data. 19 This is a phase comparator output pin for the PLL block with tri-state output. 20 DO Phase comparator output When the divided-down clock from the programmable counter is higher than the reference frequency, it will be in High-level. When it is lower, it will be in Low-level. If it matches the reference frequency, it will be in high-impedance state. VDD 20 The output is held at Low in Standby Mode. 21 PLL VCC Power supply input pin VDD This is a power supply input pin for the PLL block. 21 22 DATA 22, 23, 24 CK Serial data I/O These are serial data I/O pins. CE 23, 24 7 2004-05-07 TB2132FNG Application Note 1. Power Supply Line This IC has two voltage supply pins, VCC (for stages of AM, FM IF and MPX) and RF VCC (for FM RF stage). Please keep the potential difference between these power supply pins at 0.4 V (typ.) or less. Otherwise, it may cause the IC to malfunction. Also, please keep the potential difference between the VCC (tuner power supply) and the VDD (PLL power supply) at 1 V or less. Otherwise, due to improper interaction between analog and digital blocks, a malfunction may occur. 2. Crystal Oscillator External Constant When the constants of external components C1 and C2 are determined, please show the IC with the final layout of the board to a crystal oscillator manufacturer and test it to confirm the constants. If you need an IC to adjust parameter values to compensate for variables in layout, ask Toshiba. Please use a crystal oscillator with lower CI value C2 XI 16 C1 XO 15 Toshiba tested a crystal oscillator from DAISHINKU CORP. (CI value is 30 kΩ max) using a Toshiba evaluation board. 8 2004-05-07 TB2132FNG 3. Miscellaneous 1) 2) We offer information on software programs to control the TB2132FNG on Windows 95/98. For details, contact us. (Also contact us if you are using Windows 2000/NT.) We offer an interface board to run the TB2132FNG under software control on Windows 95/98. <Interface circuit diagram> Interface circuit VDD * * * Not mounted TC74AC125FT TB2132FN PC printer port 1 GND 2 3 11 13 17 1 VDD (22 pin) DATA VDD 9 11 12 7 8 9 14 GND 5 6 5 3 7 GND GND 14 100 µ 0.1 µ GND CK GND 4 (24 pin) CE DATA GND 10 (23 pin) CK DATA 1 CE GND VDD GND GND 18 GND *: 4.7 kΩ to 10 kΩ 4. Resistor in Interface Block • • When tuner power supply > Microcontroller power supply CE, CK and DATA should be connected to the tuner power supply via pull-up resistors. (Depending on a microcontroller specification, these pins should be connected directly to the tuner power supply, or the interface board should be inserted as shown above.) When tuner power supply < = Microcontroller power supply Only DATA should be connected to the microcontroller power supply via a pull-up resistor. 9 2004-05-07 TB2132FNG Configuration of Local Oscillator and Programmable Counter Operate the FM/TV local oscillator at approximately 200 MHz and select the counter input using the following settings of the bits. Then determine reference frequency and minimum step frequency. FM/TV OSC Counter input AM FM 1/32 TV 1/8 To MIX 1/2 To MIX FM/TV 1/2 TV 1/8 Buff 1/4 FM 1/32 1/16 AM OSC IN Programmable counter FM TV 1/2 FM OSC IN AM Mode BAND0 BAND1 Divide by 16 PW AM 1 0 * 0 FM 1/32 0 0 0 0 TV 1/8 0 1 0 0 FM 0 0 1 1 TV 1/2 0 1 1 1 Interna VCO IN AM OSC IN FM OSC IN Input Frequency Range Recommended Reference Frequency Minimum Step Frequency 1 k, 3 k, 5 k 1 k, 3 k, 5 k 0.1 MHz~40 MHz 3.125 k 50 kHz 6.25 k 50 kHz 25 kHz 25 kHz 12.5 kHz 25 kHz 30 MHz~230 MHz How to Set the Divisor A divisor of the programmable counter is set in binary using the bits P0 to P16. 1. FM OSC IN: Pulse swallow mode (set the PW bit) Pulse swallow mode (17 bits: FM and TV 1/2 Modes). Please set as shown below. MSB P16 LSB P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 17 P0 0 2 2 Divisor range n: 528~131072 (210H to 1FFFH) 2. AM OSC IN (clear the PW bit) Direct divide mode (12 bits: AM, FM 1/32, TV 1/8) please set P4 to P16 as shown below. MSB P16 LSB P15 P14 P13 P12 P11 P10 P9 P8 12 P7 P6 P5 P4 0 2 2 P3 P2 P1 P0 [Irrelevant] Divisor range n: 16~8191 (10H to 1FFFH) 10 2004-05-07 TB2132FNG Serial Transfer Format Data input mode (DOUT is in high-impedance state at input.) Completed CE 0.5 µs min 1 µs min 0.5 µs min 0.5 µs min 0.5 µs min CK Can be omitted. 0.5 µs min “ DATA “ “ “ A0 A1 A2 A3 D0 D1 D2 D3 D4 D5 D27 D28 D29 D30 D31 or D15 * 0.1 µs max Input address Can be omitted. “ Internal data * In Input Mode 2, set Low at CE pin after D15 is passed. * Do not enter the first data within 100 ms after the power supply is turned on. * At power on or reset, the reset values are set as shown in the figure below. Address Format A0 A1 A2 A3 1 0 0 0 Mode Input Mode 1 0 1 0 0 Input Mode 2 0 0 0 1 Output Mode (IF count data and data output) A3 = 0 * A2 = 0 * A1 = 0 * 11 0 0 MUTE 1 G1 1 START 0 R2 0 G0 R1 0 R0 1 IFGAIN 0 Divide by 16 0 DL BAND1 0 DO2 OUT2 0 BAND0 P16 OUT1 P15 P14 P13 P12 P11 P9 Undefined P10 P8 P7 P6 P5 P4 P3 P2 P1 Address P0 * A0 = 1 Input Mode 1 0 0 0 Reset values 2004-05-07 TB2132FNG Data in Detail • • P0 to 16: OUT1, 2: • BAND 0, 1 N (divisor data P0: LSB, P16: MSB) When set, a high appears on the OUT pin. When cleared, a low appears on the OUT pin. BAND 0 BAND 1 FM 0 0 AM 1 0 TV 0 1 1 1 Standby Mode The tuner block, the PLL block and the crystal oscillator: OFF DO: Held at Low • • • • • Note: In standby mode, the X’tal I1 and X’tal I2 bits must be cleared. Otherwise, the oscillator does not run after the TB2132FNG exits from the mode. The OUT1 and OUT2 bits can be controlled by serial input data, even in standby mode. DL: When cleared, DO is in normal state. When set, DO is held at low. DO2: When cleared, the OUT2 pin is switched to the general-purpose output port. When set, the OUT2 pin is switched to the DO output. IF GAIN: When cleared, full gain of the FM IF amplifier. When set, 2dB more gain than the full gain of the FM IF amplifier. Divide by 16: When cleared, FMOSC output: 1/32, TV OSC output: 1/8 When set, FMOSC output: 1/1, TV OSC output: 1/2 R0, 1, 2 Reference Frequency • R1 R2 1 kHz 0 0 0 1.5625 kHz 1 0 0 3 kHz 0 1 0 3.125 kHz 1 1 0 5 kHz 0 0 1 6.25 kHz 1 0 1 12.5 kHz 0 1 1 25 kHz 1 1 1 G0 G1 Measuring Time Waiting Time 0 0 1 ms 3.3 to 4.3 ms 1 0 4 ms 3.3 to 4.3 ms 0 1 16 ms 7.3 to 8.3 ms 1 1 64 ms 7.3 to 8.3 ms G0, 1 • START: • R0 MUTE: IF count start bit When cleared, maintain the count value. When set, start measuring and decrease gain by 6dB in the FM/TV IF amplifiers after the count value is reset. MUTE is turned on. When cleared, MUTE is turned off. When set, MUTE is turned on. 12 2004-05-07 TB2132FNG * 0 * 0 * 1 * 0 Input Mode 2 TEST4 TEST5 TEST6 TEST7 TEST8 0 TEST3 0 TEST2 0 PW 0 TEST1 0 Xtal I2 OSC1 0 STC OSC0 0 Xtal I1 LO/DX Reset values MO/ST Address 0 0 0 0 0 0 0 0 0 • MO/ST : When cleared, it is in Auto Mode. When set, it is in Forced Monaural Mode. • Lo DX : When cleared, full gain of the FM/TV RF amplifiers When set, 40dB less gain than the full gain of FM/TV RF amplifiers. • OSC level gain : For FM, the oscillation level of the OSC can be reduced from the viewpoint of FCC. For AM, to the contrary, the oscillation can be intensified so that the oscillator can run even with a low impedance on the SW band. OSC0 OSC1 AM OSC FM OSC 0 0 0dB 0dB 1 0 + + − − 0 1 + + + − − − 1 + + + + − − − − 1 • STC : When cleared, the OUT1 pin is switched to the general-purpose output port. When set, the OUT 1 pin is switched to the ST output (stereo output). For stereo reception, the pin is low. • PW : When the AM, FM 1/32 and TV 1/8 modes are programmed, clear the PW bit. When the TV 1/2 and FM are programmed, set the PW bit. • X’tal I1/X’tal I2 : For FM and TV, set X’tal I1 and X’tal I2 to 0 and 0. For AM, the current of the X’tal block can be reduced from the viewpoint of X’tal harmonics interference. Note: When the standby mode is selected, be sure to reset X’tal I1 and X’tal I2, respectively, to 0 and 0, or the oscillator will fail to run when the standby mode is released. • X’tal I1 X’tal I2 Oscillation Amplitude Recommended Bandwidth 0 0 Large 1 FM/TV 0 1 Large 2 1 0 Small 2 1 1 Small 1 AM TEST1 to TEST8: These bits are used for IC testing and must be always 0. 13 2004-05-07 TB2132FNG * 1 * 0 * 0 * 0 Output Mode ST BUSY OVER C19 C18 C17 C16 C15 C14 C13 C12 C11 C9 C10 C8 C7 C6 C5 C4 C3 C2 C1 C0 Address IF counting data • C0 to 19: General-purpose count data (C0: LSB, C19: MSB) • OVER: Set 1 when the measured value of general-purpose count data exceeds 20 bits. • BUSY: When a 0 is read, general-purpose count measurement completes. When a 1 is read, general-purpose count measurement is in progress. • ST: When a 0 is read, it is for monaural reception. When a 1 is read, it is for stereo reception. 14 2004-05-07 TB2132FNG Coil Data Coil No. Test Frequency L (µH) Co (pF) Qo L1 FM RF 100 MHz ⎯ ⎯ L2: TV RF 100 MHz ⎯ L3: OSC 100 MHz T1 AM OSC T2 AM IFT Turns 1-3 1-4 4-6 Wire (mmφ) Remarks 3 4 ⎯ ⎯ 0.12UEW Toko Co., Ltd. 666SNF-419Z 1 ⎯ ⎯ 0.12UEW Toko Co., Ltd. 666SNF-413IB 1 2 ⎯ ⎯ 0.16UEW Toko Co., Ltd. P666SNF-421IB 95 ⎯ ⎯ ⎯ 0.05UEW Toko Co., Ltd. 5PNR-4957Y ⎯ 109 ⎯ 7 0.05UEW Toko Co., Ltd. 5PLG-5147X 1-2 2-3 105 ⎯ ⎯ ⎯ 55 ⎯ ⎯ ⎯ ⎯ 79 ⎯ ⎯ 1 796 kHz 268 ⎯ 65 19 455 kHz ⎯ 470 60 ⎯ 3 T1: AM OSC L1: FM RF L2: TV RF L3: OSC T2: AM IFT FM C.F. Pin 25 3 4 3 3 4 2 2 1 AM C.F. 1 6 1 VCC Pin 3 6 VCC Maximum Ratings (Unless otherwise specified,Ta = 25°C) Characteristics Symbol Rating VCC, VDD −0.3 to 6.0 Output with standing voltage (NPN open collector) VO −0.3 to 6.0 CMOS input voltage VIN −0.3 to VDD + 0.3 Supply voltage Power dissipation (Note) Unit V PD 500 mW Operating temperature Topr −25 to 75 °C Storage temperature Tstg −55 to 150 °C Note: Power consumption is rated at 25°C. At temperatures higher than 25°C, power consumption is decreased by 4.8 mW per °C. 15 2004-05-07 TB2132FNG Electrical Characteristics 1. Tuner Block (Unless otherwise specified, Ta = 25°C, VCC = 3 V, F/E : f = 98 MHz, fm = 1 kHz FM IF: f = 10.7 MHz, ∆f = ±75 kHz, fm = 1 kHz AM : f = 1 MHz, MOD = 30 %, fm = 1 kHz MPX : fm = 1 kHz, PLL VCC = 3 V) Characteristics Symbol ICC (TV) Test Circuit Test Condition Min Typ. Max ⎯ 18 ⎯ ⎯ 1/2 division In TV Mode, mode incl. PLL Vin = 0 1/8 division mode incl. PLL ⎯ 16 23 ⎯ 18 ⎯ ⎯ 16 23 Supply current ICC (FM) mA ⎯ In AM Mode, Vin = 0 (incl. PLL) ⎯ 7.5 11 ⎯ Vin = 60dBµV EMF, −3dB limiting ⎯ 10 ⎯ dBµV EMF ⎯ Vin = 60dBµV EMF, −3dB limiting ⎯ 11 ⎯ dBµV EMF Vin (lim) IF ⎯ Vin = 80dBµV EMF, −3dB limiting 38 43 48 dBµV EMF Recovered output voltage VOD ⎯ Vin = 80dBµV EMF 210 260 310 mVrms Signal to noise ratio S/N ⎯ Vin = 80dBµV EMF ⎯ 72 ⎯ dB Total harmonic distortion THD ⎯ Vin = 80dBµV EMF ⎯ 0.3 ⎯ % AM rejection ratio AMR ⎯ Vin = 80dBµV EMF ⎯ 60 ⎯ dB IF count sensitivity IF sens (FM) ⎯ 52 57 62 dBµV EMF GV ⎯ Vin = 31dBµV EMF 20 38 70 mVrms VOD ⎯ Vin = 60dBµV EMF 65 90 113 mVrms Signal to noise ratio S/N ⎯ Vin = 60dBµV EMF ⎯ 40 ⎯ dB Total harmonic distortion THD ⎯ Vin = 60dBµV EMF ⎯ 1.0 ⎯ % IF sens (AM) ⎯ 39 44 49 dBµV EMF Vin max (Monaural) ⎯ ⎯ 700 ⎯ mVrms RIN ⎯ ⎯ ⎯ 55 ⎯ kΩ ROUT ⎯ ⎯ kΩ ICC (AM) FM input limiting voltage F/E Vin (lim) TV input limiting voltage Input limiting voltage FM IF Gain Recovered output voltage AM ⎯ OSC divider bypass mode In FM Mode, incl. PLL Vin = 0 1/32 division mode incl. PLL Unit IF count sensitivity Max. signal input voltage Input resistance Output resistance Separation Sep. ⎯ MPX Monaural Total harmonic distortion Stereo Voltage gain Channel balance ⎯ ⎯ fm = 1 kHz, THD = 3% L+R= 180 mVrms, P = 20 mVrms SW3: LPF ON ⎯ 5 ⎯ fm = 100 Hz ⎯ 45 ⎯ fm = 1 kHz 35 45 ⎯ fm = 10 kHz ⎯ 45 ⎯ dB THD (Monaural) ⎯ Vin = 200 mVrms ⎯ 0.2 ⎯ THD (Stereo) ⎯ L+R = 180 mVrms, P = 20 mVrms, SW3: LPF ON ⎯ 0.2 ⎯ GV ⎯ Vin = 200 mVrms −2.5 −1.0 0.5 dB C.B. ⎯ Vin = 200 mVrms −1.5 0 1.5 dB 16 % 2004-05-07 TB2132FNG Symbol Test Circuit ON VL (ON) ⎯ OFF VL (OFF) ⎯ Stereo hysteresis VH ⎯ Capture challenge C.R. Signal noise ratio Muting attenuation Characteristics Stereo sensitivity MPX Test Condition Min Typ. Max ⎯ 10 14 5 8 ⎯ Switched from monaural to stereo operation, and from stereo to monaural operation. ⎯ 2 ⎯ mVrms ⎯ P = 20 mVrms ⎯ ±8 ⎯ % S/N ⎯ Vin = 200 mVrms ⎯ 78 ⎯ dB MUTE ⎯ Vin = 200 mVrms ⎯ 78 ⎯ dB Apply pilot signal (19 kHz) Unit mVrms 2. PLL Block (Unless otherwise specified, Ta = 25°C, VDD = 3.0 V) Symbol Test Circuit Operating supply voltage range VDD ⎯ Memory retention voltage range VHD ⎯ In Standby Mode IDD1 ⎯ IDD2 Memory retention current Crystal oscillation frequency Crystal oscillation start time Characteristics Test Condition Min Typ. Max Unit 1.8 ~ 5.5 1.55 ~ 5.5 PLL operation (in pulse swallow mode) ⎯ 3.6 ⎯ mA ⎯ PLL operation (in direct divide mode) ⎯ 2.2 ⎯ mA IHD ⎯ In Standby Mode ⎯ 0.4 1.0 mA fXT ⎯ ⎯ 75 ⎯ kHz tst ⎯ ⎯ 250 ⎯ ms Min Typ. Max Unit 1.0 2.0 ⎯ mA µA Operating supply current V Crystal oscillation frequency = 75 kHz DATA at Pin 22 and CLOCK at Pin 23, CE at Pin 24 Characteristics Output current Low level Input leak current Symbol Test Circuit IOL1 ⎯ VOL = 0.3 V ILI ⎯ VIH = 3.0 V, VIL = 0 V Test Condition ⎯ ⎯ ±1.0 ~ 5.5 High level VIH1 ⎯ ⎯ VDD × 0.8 Low level VIL1 ⎯ ⎯ 0 ~ VDD × 0.2 Symbol Test Circuit Test Condition Min Typ. Max High level IOH1 ⎯ VOH = VDD − 0.3 V −0.5 −1.0 ⎯ Low level IOL1 ⎯ VOL = 0.3V 1.2 1.7 ⎯ Symbol Test Circuit Min Typ. Max High level IOH1 ⎯ VOH = VDD − 0.3 V −0.3 −0.8 ⎯ Low level IOL1 ⎯ VOL = 0.3V 0.5 1.0 ⎯ Input voltage V OUT1 (ST) at Pin 18 Characteristics Output current Unit mA OUT2 (DO2) at Pin 19 Characteristics Output current Test Condition 17 Unit mA 2004-05-07 TB2132FNG DO at Pin 20 Symbol Test Circuit High level IOH1 ⎯ VOH = Low level IOL1 ⎯ VOL = ITL ⎯ VO = Symbol Test Circuit High level IOH1 ⎯ VOH = Low level IOL1 ⎯ VOL = ITL ⎯ VO = Characteristics Test Condition Output current Output OFF-leak current Min Typ. Max 1 VDD 2 −1.5 −2.5 ⎯ 1 VDD 2 2.0 3.0 ⎯ ⎯ ⎯ ±100 nA Min Typ. Max Unit 1 VDD 2 −1.5 −2.5 ⎯ 1 VDD 2 2.0 3.0 ⎯ ⎯ ⎯ ±100 1 VDD 2 Unit mA DO2 at Pin 19 Characteristics Test Condition Output current Output OFF-leak current 18 1 VDD 2 mA nA 2004-05-07 TB2132FNG TB2132FNG Test Circuit TV/FM OSC GND VCC VtMONI CE CK DATA VtDPS (18 V) 100 µF 0.1 µF 0.01 µF 4.7 µF 390 Ω 10 µF 2SC2458 2SC2458 3.3 kΩ 1 kΩ 0.1 µF D0 OUT2 22 pF 200 Ω 2 kΩ 2 kΩ 2 kΩ 2 kΩ 100 kΩ Toko 4957 TRM 420 pF 1SV149 51 kΩ TRM 0.1 µF Coil blue Coil blue 1500 pF TMR 1000 pF 1SV262 4700 pF 51 kΩ 1000 pF 1SV262 Coil red 1500 pF 1000 pF 1SV262 Vin TMR 51 kΩ 75 Ω 75 Ω 2.7 mH 0.022 µF 2 kΩ AM RFin 0.033 µF 150 µH OUT1 0.1 µF 0.1 µF 29 28 27 26 25 24 23 22 21 20 19 18 17 16 TV RFout RF VCC AM RFin FM/TV OSC AM OSC CE CK DATA PLL VCC Do OUT2 (DO2) OUT1 (ST) PLL GND XI LPF1 11 LPF2 12 L-ch 13 R-ch 14 XO 15 75 kHz X’tal 30 FM RFout TB2132FNG DET out 9 QUAD 8 22 pF 1 µF 0.01 µF 0.01 µF 0.1 µF 0.1 µF 3.3 kΩ 1 µF 10 µF SW2 1 kΩ Vin TV/FM IFin 270 Ω 75 Ω Vin 110 kΩ Vin SW3 2.2 µF 75 Ω 110 kΩ LPF 0.022 µF AGC DET out 19 4.7 kΩ 2.2 kΩ 2.4 kΩ 2SC2458 50 Ω MPX in 10 0.1 µF SW1 IF AM IFin 7 390 Ω SFELA10 M7FA00 FE 330 Ω VCC 6 0.1 µF CDALA10M7GA128 FM IFin 5 AGC 4 SFULA450KU2B 4700 pF MIX out 3 0.47 µF TV/FM RFin GND 2 Toko 5147 FM/TV RF in 1 5V MPX out 2004-05-07 TB2132FNG Application Circuit AM in FM/TV RF in GND 1 2 MIX out 3 AGC 4 26 25 FM/TV AM OSC OSC 3 kΩ GND * 22 pF * 100 µH 5PNR-4957Y 4700 pF 24 VCC *: 4.7 kΩ~10 kΩ 0.022 µF 23 22 CHIP CLOCK DATA ENABLE 21 20 PLL VCC Do 17 16 OUT2 OUT1 (DO2) (ST) 19 18 PLL GND XI LPF2 12 R-ch 14 XO 15 47 µF GND 4.7 µF 0.1 µF 10 µF 22 pF 4.7 µF 0.015 µF L-ch 13 1 µF LPF1 11 3.3 kΩ SFULA450 KU2B MPX in 10 330 Ω ANT 0.022 µF SFELA10M 7FA00 5PRN-5147X 4700 pF 22 µF DET out 9 QUOD 8 0.1 µF AM IFin 7 330 pF VCC 6 CDALA10M7GA128 FM IFin 5 0.015 µF 75 kHz 27 RF VCC D/D CONVERTOR 0.1 µF 100 kΩ 1000 pF 1SV149 10 pF 1SV262 666SNF-421 1500 pF 430 pF 1SV149 30 pF 47 kΩ 100 kΩ 29 0.01 µF 1SV262 666SNF-413 2700 pF 47 kΩ 30 1000 pF 666SNF-419 2700 pF 47 kΩ 1000 pF 28 FM TV RFout RFout 2SC2458 2SC2458 * more than 12 V 0.01 µF 390 Ω 10 µF 2.2 kΩ 200 Ω 1SV262 0.033 µF Vtune Power 1 kΩ 4.7 µF 3.3 kΩ VT range FM 1.5 V ~ 10 V AM 1.5 V ~ 8.0 V L-ch 20 R-ch 2004-05-07 TB2132FNG Application Circuit (for FM module) FM/TV AM in FM/TV RF in GND 1 2 MIX out 3 AGC 4 26 3 kΩ 100 µH * 22 pF * GND 0.022 µF 25 FM/TV AM OSC OSC 24 23 22 CHIP CLOCK DATA ENABLE 21 20 PLL VCC Do 17 16 OUT2 OUT1 (DO2) (ST) 19 18 PLL GND XI LPF2 12 R-ch 14 XO 15 47 µF GND 0.015 µF 22 pF 4.7 µF 0.015 µF 10 µF L-ch 13 4.7 µF LPF1 11 0.1 µF MPX in 10 330 Ω ANT DET out 9 3.3 kΩ SFECS10M 7FA00 0.022 µF QUOD 8 0.022 µF 4700 pF 0.01 µF AM IFin 7 (330 pF) VCC 6 CDSCA10M7GA128 FM IFin 5 0.1 µF 75 kHz 27 RF VCC VCC *: 4.7 kΩ~10 kΩ 666SNF-421 1500 pF 1000 pF 28 FM TV RFout RFout D/D CONVERTOR 0.1 µF 47 kΩ 29 1SV262 666SNF-413 2700 pF 47 kΩ 1SV262 1000 pF 666SNF-419 2700 pF 47 kΩ 1000 pF 30 2SC2458 2SC2458 * more than 12 V 0.01 µF 390 Ω 10 µF 2.2 kΩ 200 Ω 1SV262 0.033 µF (VT = 1.5 V ~ 10 V) Vtune Power 1 kΩ 4.7 µF 3.3 kΩ L-ch 21 R-ch 2004-05-07 TB2132FNG Package Dimensions Weight: 0.17 g (typ.) 22 2004-05-07 TB2132FNG About solderability, following conditions were confirmed • Solderability (1) Use of Sn-63Pb solder Bath · solder bath temperature = 230°C · dipping time = 5 seconds · the number of times = once · use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath · solder bath temperature = 245°C · dipping time = 5 seconds · the number of times = once · use of R-type flux RESTRICTIONS ON PRODUCT USE 030619EBA • The information contained herein is subject to change without notice. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. • The products described in this document are subject to the foreign exchange and foreign trade laws. • TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. 23 2004-05-07