Rohm MCH038FN103DK Multi-layer ceramic chip capacitor Datasheet

MCH03
Ceramic capacitors
Multi-layer ceramic chip capacitors
MCH03 (0603 (0201) size, chip capacitor)
zFeatures
1) Ultra miniature (0.6mm×0.3mm×0.3mm), Ultra light weight (0.3mg)
2) Suitable for mobile devices
3) Lead-free plating terminal
4) No polarity
zQuick Reference
The design and specifications are subject to change without prior notice. Please check the most recent technical
specifications prior to placing orders or using the product. For more detail information regarding packaging style code,
please check product designation.
Thermal compensation
Part No.
Size code
Temperature characteristics
(ppm/°C)
code
Operating temp. range
(°C)
Rated voltage
(V)
Capacitance (pF)
25
0.5 to 2.7 (E12 Series) ∗
3.0 to 3.9 (E12 Series) ∗
4 to 5 (E12 Series) ∗
5.1 to 10 (E12 Series) ∗
11 to 100 (E12 Series)
0±250(CK)
0±120(CJ)
MCH03
0603
−55 to +125
A (AN)
0±60(CH)
Capacitance
tolerance
Thickness
(mm)
C(±0.25pF)
D(±0.5pF)
J(±5%)
0.3 ± 0.03
∗ : 0.5pF/0.75pF/2pF/3pF/4pF/5pF/6pF/7pF/8pF/9pF available
zHigh dielectric constant
Part No.
Size code
Temperature characteristics
code
Operating temp. range
(°C)
±10%(B)
CN
MCH03
0603
FN
±15%
(R) (X7R)
Capacitance (pF)
Capacitance
tolerance
100 to 2,200 (E6 Series)
4,700 (E3 Series)
100 to 2,200 (E6 Series)
4,700 (E3 Series)
10,000 (E6 Series)
K (±10%)
−55 to +85
25
16
25
16
6.3
−25 to +85
16
10,000 (E1 Series)
−30 to +85
16
10,000 (E1 Series)
−25 to +85
−55 to +125
±15%(X5R)
+30%, −80%
(F)
+22%, −82%
(Y5V)
Rated voltage
(V)
Thickness
(mm)
0.3 ± 0.03
Z (+80%, −20%)
zExternal dimensions (Unit : mm)
0.1Min. 0.17Min.
0.3±0.03
0.3±0.03
0.3±0.03
0.6±0.03
0.3±0.03
Rev.A
1/12
MCH03
Ceramic capacitors
zProduct designation
Code Prduct thickness
K
0.3mm
Packing specification
Reel
Basic ordering unit(pcs.)
Paper tape(width 8mm, pitch 2mm)
φ180mm (7in.)
15,000
Packaging Style
Part No.
M C H
Rated voltage
Code Voltage
8
6.3V
3
16V
2
25V
0 3
3
F N
1 0 3
Temperature characteristic code
:Refer to quick reference table.
Z
K
Nominal
capacitance
Capacitance tolerance
Tolerance
Code
K
±0.25pF(0.5 to 5pF)
±0.5pF(5.1 to 10pF)
±5%(11pF or more)
±10%
Z
+80%, −20%
C
3-digit
designation
accordijg
to IEC
D
J
zProduct No.list
•Thermal compensation capacitors
Capacitance
(pF)
0.5
0.75
1.0
1.2
1.5
1.8
2.0
2.2
2.7
3.0
3.3
3.9
4.0
4.7
5.0
5.6
6
6.8
7
8
8.2
9
10
Temperature
A AN(CG) (COG) (CH) Characteristic
25V
Rated voltage (V)
Product No.
Tolerance Product thickness(mm)
MCH032A (AN) 0R5CK
MCH032A (AN) R75CK
MCH032A (AN) 010CK
MCH032A (AN) 1R2CK
MCH032A (AN) 1R5CK
MCH032A (AN) 1R8CK
MCH032A (AN) 020CK
MCH032A (AN) 2R2CK
C (±0.25pF)
MCH032A (AN) 2R7CK
MCH032A (AN) 030CK
MCH032A (AN) 3R3CK
MCH032A (AN) 3R9CK
0.6 ± 0.03
MCH032A (AN) 040CK
MCH032A (AN) 4R7CK
MCH032A (AN) 050CK
MCH032A (AN) 5R6DK
MCH032A (AN) 060DK
MCH032A (AN) 6R8DK
MCH032A (AN) 070DK
D (±0.5pF)
MCH032A (AN) 080DK
MCH032A (AN) 8R2DK
MCH032A (AN) 090DK
MCH032A (AN) 100DK
Capacitance
(pF)
12
15
18
22
27
33
39
47
56
68
82
100
Temperature
A AN(CG) (COG) (CH) Characteristic
25V
Rated voltage (V)
Product No.
Tolerance Product thickness(mm)
MCH032A (AN) 120JK
MCH032A (AN) 150JK
MCH032A (AN) 180JK
MCH032A (AN) 220JK
MCH032A (AN) 270JK
MCH032A (AN) 330JK
J (±5%)
0.6 ± 0.03
MCH032A (AN) 390JK
MCH032A (AN) 470JK
MCH032A (AN) 560JK
MCH032A (AN) 680JK
MCH032A (AN) 820JK
MCH032A (AN) 101JK
Rev.A
2/12
MCH03
Ceramic capacitors
•High dielectric constant capacitors
Capacitance
(pF)
100
150
220
330
470
680
1,000
1,500
2,200
4,700
10,000
Capacitance
(pF)
10,000
Temperature
Rated voltage (V)
Tolerance Product thickness(mm)
K (±10%)
0.6 ± 0.03
CN (R) (B) (X7R) Characteristic
16V
25V
Product No.
Product No.
MCH032CN101KK
MCH032CN151KK
MCH032CN221KK
MCH032CN331KK
MCH032CN471KK
MCH032CN681KK
MCH032CN102KK
MCH032CN152KK
MCH032CN222KK
MCH033CN472KK
CN (X5R) Characteristic
6.3V
Product No.
MCH038CN103KK
Temperature
FN(F) (Y5V) Characteristic
16V
Rated voltage (V)
Product No.
Tolerance Product thickness(mm)
MCH033FN103ZK
Z (+80%, −20%)
0.6 ± 0.03
Rev.A
3/12
MCH03
Ceramic capacitors
•Performance and test method
No.
Items
Performance
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
1
Appearance and
dimensions
No marked defects shall be allowed As per 4.4 of JIS C 5101-1.
for appearance.
As per 4.5 of JIS C 5101-10
Dimensions shall be as specified the Using a Magnifier.
clause 4.
2
Withstanding voltage
No dielectrical breakdown or other
damage shall be allowed.
As per 4.6 of JIS C 5101-1.
As per 4.6.4 of JIS C 5101-10
Voltage shall be applied as per Table1.
Table 1
CharacVoltage
teristic
A, AN 300% Rated voltage
CN
250% Rated voltage
FN
Voltage shall be applied for 1 to 5s with
50mA charging and discharging curent.
3
Insulation resistance
Not less than 10000MΩ or
500MΩ µF, whichever is less.
(For products with rated voltage less
than 16V, it is not less than 10000MΩ
or 100MΩ µF, whichever is less.)
As per 4.5 of JIS C 5101-1.
As per 4.6.3 of JIS C 5101-10
Measurements shall be made after
60+/−5s period of the rated voltage
applied.
4
Capacitance
Capacitance shall be
within specified tolerance range.
As per 4.7 of JIS C 5101-1.
As per 4.6.1 of JIS C 5101-10
Measurements shall be made under the
conditions specified in Table 2.
Characteristic
A, AN
CN
FN
5 Dielectric loss tangent
A, AN
CN
FN
Capacitance < 30pF
tan δ <
− 100/(400+20C)%
< 30pF
Capacitance −
tan δ <
− 0.1%
Table 2
Frequency Voltage
<
> 1000 pF
− 1000 pF
1+/−0.1MHz
1+/−0.1kHz
1+/−0.1Vrms. 1+/−0.1Vrms.
1+/−0.1kHz
1+/−0.1Vrms.
As per 4.8 of JIS C 5101-1.
As per 4.6.2 of JIS C 5101-10
Measurements shall be made under the
conditions specified in Table 2.
Rated voltage=25V
tan δ <
− 3.0%
Rated voltage=16V
tan δ <
− 5.0%
Rated voltage=6.3V
tan δ <
− 10.0%
Rated voltage=16V
tan δ <
− 10.0%
Rev.A
4/12
MCH03
Ceramic capacitors
No.
Items
6 Temperature
characteristic
Performance
A, AN
CN
FN
Capacitance C <
− 2pF
0+/−250ppm/°C
Capacitance C=3pF
0+/−120ppm/°C
Capacitance C <
− 4pF
0+/−60ppm/°C
(−55°C to +125°C)
X7R
R
+/−15%
(−55°C to +125°C)
B
+/−10%
(−25°C to +85°C)
X5R
+/−15%
(−55°C to +85°C)
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
As per 4.24 of JIS C 5101-1.
As per 4.7 of JIS C 5101-10
Temperature coefficient shall be calculated
at 20°C and 85°C.
As per 4.24 of JIS C 5101-1.
As per 4.7 of JIS C 5101-10
If required, measurements shall be made
at a given temperature.
+30%, −80%
(−25°C to +85°C)
+22%, −82%
(−30°C to +85°C)
7 Solderability
8 Resistance
to solderin
heat
More than 3/4 of each end
termination shall be covered with
new solder.
Appearance Without mechanical damage.
Change
rate from
initial value
A, AN
Within +/−2.5% or
+/−0.25pF whichever
is larger.
CN
Within +/−7.5%
FN
Within +/−20%
Dielectric
loss
tangent
Within specified initial value.
Insulation
resistance
Within specified initial value.
Withstanding No defects shall be allowed.
voltage
9 End termination
adherence
Without peeling or sign of
peeling shall be allowed
on the end terminations.
As per 4.15.2 of JIS C 5101-1.
As per 4.11 of JIS C 5101-10
The solder specified in JIS Z 3282 H63A
shall be used. Ans the flux containing 25%
rosin and ethanol solution shall be used.
The specimens shall be immersed into the
solder at 235+/−5°C for 2+/−0.5s
So that both end terminations are
completely under solder.
As per 4.14 of JIS C 5101-1.
As per 4.10 of JIS C 5101-10
The solder specified in JIS Z 3282. H63A
shall be used.
The specimens shall be immersed into the
solder at 260+/−5°C for 5+/−0.5s so that
both end terminations are completely
under the solder.
Pre-heating at 150+/−10°C for 1 to 2min
Initial measurements prior to test shall be
performed after the thermal
Pre-conditioning specified in Remarks (1).
Final measurements shall be made after the
specimens have been left at room
temperature as per Table3.
Table3
Characteristic
A, AN
CN, FN
Time
24+/−2 h
48+/−4 h
As per 4.13 of JIS C 5101-1.
As per 4.8 ofJIS C 5101-10
A 2N weight for 10+/−1s shall be applied
to the soldered specimens as shown by the
arrow mark in the below sketch.
Applied pressure
Substrate
Capacitor
Rev.A
5/12
MCH03
Ceramic capacitors
No.
Items
Performance
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
10 Bending
strength
Appearance
Without mechanical damage.
As per 4.35 of JIS C 5101-1.
As per 4.9 of JIS C 5101-10
Glass epoxy board with soldered
specimens shall be bent till 1mm by
1.0mm/s.
11 Vibration
Appearance
Without mechanical damage.
As per 4.17 of JIS C 5101-1
The specimens shall be soldered on the
specified test jig.
Initial measurements shall be made after
the thermal pre-conditioning specified in
Remarks(1).
Final measurements shall be made after the
specimens have been left at room
temperature as per Table3.
[Condition]
Directions : 2h each X, Y and Z directions
Total : 6h
Frequency range : 10 to 55 to 10Hz(1min)
Applitude : 1.5mm
(shall not exceed acceleration196m/s2)
Change
rate from
initial value
Dielectric
loss
tangent
A, AN
Capacitance shall be
within specified
tolerance range.
CN
Within +/−7.5%
FN
Within +/−20%
Within specified initial value.
Table3
Characteristic
A, AN
CN, FN
12 Temperature Appearance
cycling
Change
rate from
initial value
Without mechanical damage.
A, AN
CN
Rated
voltage
25V,16V
Rated
voltage
6.3V
FN
Dielectric
loss
tangent
Insulation
resistance
Time
24+/−2 h
48+/−4 h
As per 4.16 of JIS C 5101-1
As per 4.12 of JIS C 5101-10
Within +/−2.5% or
The specimens shall be soldered on the test
+/−0.25pF whichever jig shown in Remarks.
is larger.
Temperature cycle : 5cycles Initial
measurements prior to test shall be
performed after the thermal
Within +/−7.5%
per-conditioning specified in Remarks (1).
Final measurements shall be made after the
Within +/−10.0% specimens have been left at room
temperature as per Table3.
Within +/−20%
Within specified initial value.
Within specified initial value.
Withstanding No defects shall be allowed.
voltage
Test condition
Step
Temp. (°C)
Time (min)
1
Min operating temp.
2
Room temp.
30+/−3
<
−3
3
Max operating temp.
4
Room temp.
30+/−3
<
−3
Table3
Characteristic
A, AN
CN, FN
Time
24+/−2 h
48+/−4 h
Rev.A
6/12
MCH03
Ceramic capacitors
No.
13 Humidity
(Steady)
Items
Performance
Appearance Without mechanical damage.
Change
rate from
initial value
A, AN
Rated
voltage
25V,16V
CN
Rated
voltage
6.3V
FN
Dielectric
tangent
Insulation
resistance
14 Humidity
life test
Within +/−5.0% or
+/−0.5pF whichever
is larger.
Within +/−12.5%
Within +/−25.0%
Within +/−30.0%
tan δ <
− 0.3%
Less than 200% of
CN
initial spec.
Less than 150% of
FN
initial spec.
Not less than 1000MΩ or
50MΩ µF, whichever is less.
(For products with rated
voltage less than 16V, it is not less
than 1000MΩ or 10MΩ µF,
whichever is less.)
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
As per 4.22 of JIS C 5101-1
JIS C 5101-10
Test temperature : 60+/−2°C
Relative humidity : 90 to 95%
Test time
: 500 +24/−0 h
Initial measurements prior to test shall
be made after the voltage
pre-conditioning specified in
Remarks (2).
Final measurements have been left at
room temperature as per Table3.
Table3
A, AN
Characteristic
A, AN
CN, FN
Time
24+/−2 h
48+/−4 h
Appearance Without mechanical damage.
Change
rate from
initial value
Dielectric
loss
tangent
As per 4.22 of JIS C 5101-1
As per 4.14 of JIS C 5101-10
Within +/−7.5% or
A, AN
Test temperature : 60+/−2°C
+/−0.75pF whichever Relative humidity : 90 to 95%
is larger.
Voltage : Rated voltage
Rated
Test time : 500 +24/−0 h
Within +/−12.5%
voltage
Initial measurements prior to test shall
25V,16V
be made after the voltage
CN
Rated
pre-conditioning specified in
Within +/−25.0%
voltage
Remarks (2).
6.3V
Final measurements shall be made after
Within +/−30.0%
FN
the specimens have been left at room
temperature as per Table3.
tan δ <
A, AN
− 0.5%
CN
FN
Insulation
resistance
Less than 200% of
initial spec.
Less than 150% of
initial spec.
Not less than 500MΩ or
25MΩ µF, whichever is less.
(For products with rated voltage less
than 16V, it is not less than 500mΩ
or 5MΩ µF, whichever is less.)
Table3
Characteristic
A, AN
CN, FN
Time
24+/−2 h
48+/−4 h
Rev.A
7/12
MCH03
Ceramic capacitors
No.
Items
15 Heat life
test
Performance
Appearance Without mechanical damage.
Change
rate from
initial value
A, AN
CN
Dielectric
loss
tangent
Insulation
resistance
Rated
voltage
25V,16V
Rated
voltage
6.3V
Within +/−3.0% or
+/−0.3pF whichever
is larger.
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
As per 4.23 of JIS C 5101-1.
As per 4.15 of JIS C 5101-10
Test
Voltage
temperature(°C)
Within +/−15.0%
A, AN
125
CN
85
(B, X5R)
Within +/−25.0%
FN
Within +/−30.0%
A, AN
tan δ <
− 0.3%
CN
Less than 200% of
initial spec.
FN
Less than 150% of
initial spec.
Not less than 1000MΩ or
50MΩ µF, whichever is less.
(For products with rated voltage less
than 16V, it is not less than 1000mΩ
or 10MΩ µF, whichever is less.)
125
(R, X7R)
FN
85
200%
Rated
voltage
200%
Rated
voltage
200%
Rated
voltage
200%
Rated
voltage
Test
time (h)
1000
+48/−0
1000
+48/−0
1000
+48/−0
Initial measurements prior to test shall be
made after the voltage pre-conditioning
specified in Remarks (2).
Final measurements shall be made after
the specimens have been left at room
temperature
Table3
Characteristic
A, AN
CN, FN
Time
24+/−2 h
48+/−4 h
[Remarks]
Pre-conditioning
If specified in test method of as per 3(Performance and test merhod), capacitors of CN, FN
characteristics shall be pre-conditionded as follows.
(1) Thermal pre-conditioning
Prior to initial measurements, specimens shall be conditioned at a temperature of 150 0/−10°C
for a period of 1hr., and shall be allowed to stabilize at room temperature for 48+/−4h
(2) Voltage pre-conditioning
Prior to initial measurements, voltage specified as a test condition shall be applied to specimens
for a period of 1hr., and the specimens shall be allowed to stabilize at room temperature for 48+/−4h
<Test jig>
Soldering
Glass epoxy
substrate
Rev.A
8/12
MCH03
Ceramic capacitors
zPackaging specifications
Taping dimensions
Reel dimensions
t
φJ
d
E
+1.0
9.0 −0
Pulling direction
A
D
G
H
+0
φ180 −1.5
φ13.0 +
− 0.2
t1
F
φ60.0+1.0
−0
C
B
Pulling direction
C
Symbol
D
E
F
G
H
d
J
t
t1
0.37
0.42
0.5
8.0
3.5
1.75
2.0
2.0
4.0
φ1.5
Dimensions +/ −0.2 +/ −0.05 +/ −0.1 +/ −0.05 +/ −0.05 +/ −0.1 +0.1/ −0
+/ −0.02 +/ −0.02 MAX.
Symbol
Style
MCH03
A
B
0.37
+/ −0.03
0.67
+/ −0.03
(Unit : mm)
Label pasting
As per EIAJ ET−7200A
(Unit : mm)
(Unit : mm)
(1) The quantity for one reel is as bellows.
Kind of reel
φ180 reel
Series
Paper tape
Quantity
MCH03 15,000 pcs.
Symbol
K
(2) When the tape is pulled out towards the operator with the cover tape facing
upward, the feeding holes shall be found on the right portion of the tape.
(3) Specification of beginning and ending of the tape are as follows.
Ending(reel's center)
Beginning(reel's round)
: Approx. 300mm (no chips)
: Approx. 270mm (no chips)
: Approx. 30mm (no pasted tape)
: Approx. 260mm (cover tape only)
(4) No juncture of tape shall be allowed.
(5) The share strength of tape shall be more than 5N at the break down strength.
(6) The peel strength of the cover tape shall be 0.1 to 0.7(N) when the cover tape are
peeled 0 to 15° degree from the surface.
(7) The number of missing components shall not exceed 0.1% of the total number
of components (marked number) or one whichever is the larger, and no consecutive
missing exceeding two is allowed.
(8) The reels made from resin shall be used, as per EIAJ ET-7200A.
zMarking
No marking shall be performed on the chip.
Trademark, parts number, quantity, lot No. , and country of origin shall be labeled on each reel, bulk case.
zNumbering system for LOT No.
Example
03
(1)
01
(2)
A0001
(3)
J
(4)
(1) The end of the Christian Era < two digits> of production finish.
(2) Week in completing part of production finish.
(3) Manufacture continuity number.
(4) The symbol of manufacturing plant.
Rev.A
9/12
MCH03
Ceramic capacitors
zLabel expression
The Figure below is label expression
< Label Example > Part Number : MCH032A470JK
④
①
MCH032A470JK
②
③
□ 15,000pcs 0501 00001F
⑤
0123456789ABCDEFGHI J0123456789ABCDEFGHI J
JAPAN
⑦
K.SATO
Excellence in Electronics
ROHM
⑧
⑥
①
②
③
④
⑤
⑥
⑦
⑧
Part Number
Division cord
Quantity
Lot No.
The Country of origin
Inspector
QR code
Trademark
Rev.A
10/12
MCH03
Ceramic capacitors
zPacking method
1) φ180mm Reel
EIAJ cole
B'
2
C'
(reel)
Label
A'
[width of 9mm : 5reel]
1
A
(interior box of R-26)
Packing slip
B
C
(R-26)
< Packaging unit >
Symbol
Dimensions
K
R-26
Quantity of reel in
interior box
Quantity of reel in
box of R-26
5
20
Packaging
interior box of R-26
A (A’)
195
185
B (B’)
255
60
C (C’)
190
185
(Unit : mm)
< Appearance >
Carton
< Accumulation >
You must do accumulation by ten boxes
< Packaging slip >
1.
2.
3.
4.
5.
Customer
Parts number
Quantity
Box quantity
Trade mark
zWeight / Piece
(Unit : mg)
Size
Item
Thickness
0603 (0201)
MCH03
0.3mm
Characteristic
Weight / Piece
A, AN
0.3
CN
0.3
FN
0.3
(Note) The measured values in the table are for reference only.
Actual weight of these chips may very slightly lot by lot.
Rev.A
11/12
MCH03
Ceramic capacitors
zElectrical characteristics
gA (C0G) Characteristics
1000000
RATE OF CAPACITANCE CHANGE : (%)
5
4
100000
3
10000
2
1
1000
IMPEDANCE (Ω)
0
−1
−2
−3
−4
−5
−50
0
50
0.5pF
100
10pF
10
1
0.1
100
1
10
100
1000
10000
TEMPERATURE (°C)
FREQUENCY (MHz)
Fig.1 Capacitance-temperature
characteristics
Fig.2 Impedance-frequency
characteristics
gCN (X7R) Characteristics
1000000
20
100000
10
0
10000
−10
−20
10
5
−80
−40
0
40
80
120
1000
IMPEDANCE (Ω)
−30
Dissipation factor (%)
CAPACITANCE CHANGE : (%)
30
100
10
0.1
160
1000pF
1
1
10
100
1000
10000
FREQUENCY (MHz)
TEMPERATURE : (°C)
Fig.4 Impedance-frequency
characteristics
Fig.3 Capacitance-temperature
characteristics
20
10
0
−10
−20
−30
−40
−50
−60
−70
−80
60
50
40
30
20
10
−80
−40
0
40
80
120
Dissipation factor (%)
CAPACITANCE CHANGE : (%)
gFN (Y5V) Characteristics
160
TEMPERATURE : (°C)
Fig.5 Capacitance-temperature
characteristics
Rev.A
12/12
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
Similar pages