Murata LQW15AN1N3D10D Chip inductor (chip coil) for high frequency horizontal wire wound Datasheet

Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Horizontal Wire Wound
Data Sheet
Chip Inductor (Chip Coil)
1
for High Frequency Horizontal Wire Wound
LQW15A_10 Series (High Q/Low DC Resistance Type) (0402 Size)
■ Packaging
0.5±0.1
1.0±0.1
0.6±0.1
0.2±0.1
Code
Packaging
Minimum Quantity
D
180mm Paper Tape
10000
B
Bulk(Bag)
500
0.10±0.05
0.5±0.1
■ Dimensions
0.2±0.1
(in mm)
■ Rated Value (p: packaging code)
Part Number
Inductance
Test Frequency
Rated Current
Max. of DC resistance Q (min.) Test Frequency
Self Resonance Frequency (min.)
LQW15AN1N3C10p
1.3nH±0.2nH
100MHz
1200mA
0.017ohm
20
250MHz
16.0GHz
LQW15AN1N3D10p
1.3nH±0.5nH
100MHz
1200mA
0.017ohm
20
250MHz
16.0GHz
LQW15AN2N2C10p
2.2nH±0.2nH
100MHz
1000mA
0.027ohm
25
250MHz
14.0GHz
LQW15AN2N2D10p
2.2nH±0.5nH
100MHz
1000mA
0.027ohm
25
250MHz
14.0GHz
LQW15AN2N4D10p
2.4nH±0.5nH
100MHz
1000mA
0.027ohm
25
250MHz
14.0GHz
LQW15AN3N3D10p
3.3nH±0.5nH
100MHz
900mA
0.040ohm
30
250MHz
12.0GHz
LQW15AN3N4C10p
3.4nH±0.2nH
100MHz
900mA
0.040ohm
30
250MHz
12.0GHz
LQW15AN3N4D10p
3.4nH±0.5nH
100MHz
900mA
0.040ohm
30
250MHz
12.0GHz
LQW15AN3N6C10p
3.6nH±0.2nH
100MHz
900mA
0.040ohm
30
250MHz
9.5GHz
LQW15AN3N6D10p
3.6nH±0.5nH
100MHz
900mA
0.040ohm
30
250MHz
9.5GHz
LQW15AN3N9D10p
3.9nH±0.5nH
100MHz
900mA
0.040ohm
30
250MHz
7.0GHz
LQW15AN4N7D10p
4.7nH±0.5nH
100MHz
800mA
0.051ohm
30
250MHz
8.0GHz
LQW15AN5N1C10p
5.1nH±0.2nH
100MHz
800mA
0.051ohm
30
250MHz
8.0GHz
LQW15AN5N1D10p
5.1nH±0.5nH
100MHz
800mA
0.051ohm
30
250MHz
8.0GHz
LQW15AN5N6C10p
5.6nH±0.2nH
100MHz
800mA
0.051ohm
30
250MHz
8.0GHz
LQW15AN5N6D10p
5.6nH±0.5nH
100MHz
800mA
0.051ohm
30
250MHz
8.0GHz
Operating Temperature Range: -55°C to +125°C
Only for reflow soldering.
Continued on the following page.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.9.9
http://www.murata.com/
Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Horizontal Wire Wound
Data Sheet
2
Continued from the preceding page.
■ Q-Frequency Characteristics (Typ.)
■ Inductance-Frequency Characteristics (Typ.)
250
10
1.3nH
5.6nH
Inductance (nH)
200
150
Q
3.6nH
5.6nH
100
3.6nH
50
1.3nH
0
10
1
100
1000
10
10000
100
1000
10000
Frequency (MHz)
Frequency (MHz)
■ !Caution/Notice
!Caution (Rating)
Do not use products beyond the rated current as
this may create excessive heat.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profile
where peak solder temperature is below the Tin melting
point is used. Please confirm the solderability of Tin
plating termination chip before use.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.9.9
http://www.murata.com/
Similar pages