Cypress CY62157EV30LL-45BVXA 8-mbit (512 k x 16) static ram automatic power down when deselected Datasheet

CY62157EV30 MoBL®
8-Mbit (512 K × 16) Static RAM
8-Mbit (512 K × 16) Static RAM
Features
Functional Description
■
Thin small outline package (TSOP) I package configurable as
512 K × 16 or 1 M × 8 static RAM (SRAM)
■
High speed: 45 ns
■
Temperature ranges
❐ Industrial: –40 °C to +85 °C
❐ Automotive-A: –40 °C to +85 °C
❐ Automotive-E: –40 °C to +125 °C
■
Wide voltage range: 2.20 V to 3.60 V
■
Pin compatible with CY62157DV30
■
Ultra low standby power
❐ Typical standby current: 2 A
❐ Maximum standby current: 8 A (Industrial)
■
Ultra low active power
❐ Typical active current: 1.8 mA at f = 1 MHz
■
Easy memory expansion with CE1, CE2, and OE features
■
Automatic power down when deselected
■
Complementary Metal Oxide Semiconductor (CMOS) for
optimum speed and power
■
Available in Pb-free and non Pb-free 48-ball very fine-pitch ball
grid array (VFBGA), Pb-free 44-pin TSOP II and 48-pin TSOP I
packages
The CY62157EV30 is a high performance CMOS static RAM
organized as 512K words by 16 bits. This device features
advanced circuit design to provide ultra low active current. This
is ideal for providing More Battery Life (MoBL®) in portable
applications such as cellular telephones. The device also has an
automatic power down feature that significantly reduces power
consumption when addresses are not toggling. Place the device
into standby mode when deselected (CE1 HIGH or CE2 LOW or
both BHE and BLE are HIGH). The input or output pins (I/O0
through I/O15) are placed in a high impedance state when the
device is deselected (CE1HIGH or CE2 LOW), the outputs are
disabled (OE HIGH), Byte High Enable and Byte Low Enable are
disabled (BHE, BLE HIGH), or a write operation is active (CE1
LOW, CE2 HIGH and WE LOW).
To write to the device, take Chip Enable (CE1 LOW and CE2
HIGH) and Write Enable (WE) inputs LOW. If Byte Low Enable
(BLE) is LOW, then data from I/O pins (I/O0 through I/O7) is
written into the location specified on the address pins (A0 through
A18). If Byte High Enable (BHE) is LOW, then data from I/O pins
(I/O8 through I/O15) is written into the location specified on the
address pins (A0 through A18).
To read from the device, take Chip Enable (CE1 LOW and CE2
HIGH) and Output Enable (OE) LOW while forcing the Write
Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data
from the memory location specified by the address pins appear
on I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from
memory appears on I/O8 to I/O15. See Truth Table on page 13
for a complete description of read and write modes.
Logic Block Diagram
512 K × 16/1 M x 8
RAM Array
SENSE AMPS
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
ROW DECODER
DATA IN DRIVERS
I/O0–I/O7
I/O8–I/O15
COLUMN DECODER
BYTE
BHE
WE
CE2
CE1
BHE
A11
A12
A13
A14
A15
A16
A17
A18
Power Down
Circuit
OE
BLE
CE2
CE1
BLE
Cypress Semiconductor Corporation
Document #: 38-05445 Rev. *I
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 30, 2011
[+] Feedback
CY62157EV30 MoBL®
Contents
Pin Configuration .............................................................3
Product Portfolio ..............................................................3
Maximum Ratings .............................................................4
Operating Range ...............................................................4
Electrical Characteristics .................................................4
Capacitance ......................................................................5
Thermal Resistance ..........................................................5
Data Retention Characteristics .......................................6
Data Retention Waveform ................................................6
Switching Characteristics ................................................7
Switching Waveforms ......................................................8
Read Cycle No. 1 (Address Transition Controlled) .....8
Read Cycle No. 2 (OE Controlled) ..............................8
Write Cycle No. 1 (WE Controlled) ..............................9
Write Cycle No. 2 (CE1 or CE2 Controlled) ..............10
Document #: 38-05445 Rev. *I
Write Cycle No. 4
(BHE/BLE Controlled, OE LOW) ......................................12
Truth Table ......................................................................13
Ordering Information ......................................................14
Ordering Code Definitions .........................................14
Package Diagrams ..........................................................15
Acronyms ........................................................................18
Document Conventions .................................................18
Units of Measure .......................................................18
Document History Page .................................................19
Sales, Solutions, and Legal Information ......................21
Worldwide Sales and Design Support .......................21
Products ....................................................................21
PSoC Solutions .........................................................21
Page 2 of 21
[+] Feedback
CY62157EV30 MoBL®
Pin Configuration
Figure 1. 48-ball VFBGA (Top View) [1]
1
2
3
4
5
6
BLE
OE
A0
A1
A2
CE 2
A
I/O8
BHE
A3
A4
CE 1
I/O0
B
I/O9
I/O10
A5
A6
I/O1
I/O2
C
A17
A7
I/O3
VCC
D
NC
A16
I/O4
VSS
E
I/O14 I/O13 A14
A15
I/O5
I/O6
F
VSS I/O11
VCC
I/O12
I/O15
NC
A12
A13
WE
I/O7
G
A18
A8
A9
A10
A11
NC
H
Figure 2. 44-pin TSOP II (Top View) [2]
A4
A3
A2
A1
A0
CE
I/O0
I/O1
I/O2
I/O3
VCC
VSS
I/O4
I/O5
I/O6
I/O7
WE
A18
A17
A16
A15
A14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
A5
A6
A7
OE
BHE
BLE
I/O15
I/O14
I/O13
I/O12
VSS
VCC
I/O11
I/O10
I/O9
I/O8
A8
A9
A10
A11
A12
A13
Figure 3. 48-pin TSOP I (512 K × 16/1 M × 8) (Top View) [1, 3]
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
WE
CE2
NC
BHE
BLE
A18
A17
A7
A6
A5
A4
A3
A2
A1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
A16
BYTE
Vss
I/O15/A19
I/O7
I/O14
I/O6
I/O13
I/O5
I/O12
I/O4
Vcc
I/O11
I/O3
I/O10
I/O2
I/O9
I/O1
I/O8
I/O0
OE
Vss
CE1
A0
Product Portfolio
Power Dissipation
Product
CY62157EV30LL
Range
VCC Range (V)
Speed
(ns)
Operating ICC, (mA)
f = 1 MHz
Min
Typ [4]
Max
Industrial/Auto-A
2.2
3.0
3.6
Auto-E
2.2
3.0
3.6
f = fmax
Standby, ISB2
(A)
Typ [4]
Max
Typ [4]
Max
Typ [4]
45
1.8
3
18
25
2
8
55
1.8
4
18
35
2
30
Max
Notes
1. NC pins are not connected on the die.
2. The 44-pin TSOP II package has only one chip enable (CE) pin.
3. The BYTE pin in the 48-pin TSOP I package must be tied HIGH to use the device as a 512 K × 16 SRAM. The 48-pin TSOP I package can also be used as a 1 M × 8
SRAM by tying the BYTE signal LOW. In the 1 M x 8 configuration, Pin 45 is A19, while BHE, BLE and I/O8 to I/O14 pins are not used (NC).
4. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C.
Document #: 38-05445 Rev. *I
Page 3 of 21
[+] Feedback
CY62157EV30 MoBL®
Maximum Ratings
Output Current into Outputs (LOW) ............................20 mA
Exceeding the maximum ratings may impair the useful life of the
device. User guidelines are not tested.
Storage Temperature ............................. –65 °C to + 150 °C
Ambient Temperature with
Power Applied ........................................ –55 °C to + 125 °C
Supply Voltage to Ground
Potential .............................–0.3 V to 3.9 V (VCCmax + 0.3 V)
DC Voltage Applied to Outputs
in High Z State [5, 6] ............–0.3 V to 3.9 V (VCCmax + 0.3 V)
Static Discharge Voltage ........................................> 2001 V
(MIL-STD-883, Method 3015)
Latch Up Current ...................................................> 200 mA
Operating Range
Device
Range
Ambient
Temperature
VCC [7]
CY62157EV30LL Industrial/ –40 °C to +85 °C 2.2 V to 3.6 V
Auto-A
Auto-E
DC Input Voltage [5, 6] ........ –0.3 V to 3.9 V (VCC max + 0.3 V)
–40 °C to +125 °C
Electrical Characteristics
Over the Operating Range
Parameter
VOH
VOL
VIH
VIL
Description
Output HIGH voltage
Output LOW voltage
Input HIGH voltage
Input LOW voltage
Test Conditions
45 ns (Industrial/
Auto-A)
55 ns (Auto-E)
Unit
Min
Typ [8]
Max
Min
Typ [8]
Max
IOH = –0.1 mA
2.0
–
–
2.0
–
–
V
IOH = –1.0 mA, VCC > 2.70 V
2.4
–
–
2.4
–
–
V
IOL = 0.1 mA
–
–
0.4
–
–
0.4
V
IOL = 2.1 mA, VCC > 2.70 V
–
–
0.4
–
–
0.4
V
VCC = 2.2 V to 2.7 V
1.8
–
VCC + 0.3
1.8
–
VCC + 0.3
V
VCC = 2.7 V to 3.6 V
2.2
–
VCC + 0.3
2.2
–
VCC + 0.3
V
VCC = 2.2 V to 2.7 V
–0.3
–
0.6
–0.3
–
0.6
V
VCC = 2.7 V to 3.6 V
–0.3
–
0.8
–0.3
–
0.8
V
–1
–
+1
–4
–
+4
A
–
+1
–4
–
+4
A
IIX
Input leakage current
GND < VI < VCC
IOZ
Output leakage current GND < VO < VCC, Output Disabled
–1
ICC
VCC operating supply
current
–
18
25
–
18
35
–
1.8
3
–
1.8
4
mA
f = fmax = 1/tRC
f = 1 MHz
VCC = VCCmax
IOUT = 0 mA
CMOS levels
ISB1 [9]
Automatic CE power CE1 > VCC 0.2 V or CE2 < 0.2 V
down current — CMOS or (BHE and BLE) > VCC – 0.2 V,
inputs
VIN > VCC – 0.2 V, VIN < 0.2 V
f = fmax (Address and Data Only),
f = 0 (OE and WE), VCC = 3.60 V
–
2
8
–
2
30
A
ISB2 [9]
Automatic CE power CE1 > VCC – 0.2 V or CE2 < 0.2 V
down current — CMOS or (BHE and BLE) > VCC – 0.2 V,
inputs
VIN > VCC – 0.2 V or VIN < 0.2 V,
f = 0, VCC = 3.60 V
–
2
8
–
2
30
A
Notes
5. VIL(min) = –2.0 V for pulse durations less than 20 ns.
6. VIH(max) = VCC + 0.75 V for pulse durations less than 20 ns.
7. Full device AC operation assumes a 100 s ramp time from 0 to Vcc(min) and 200 s wait time after VCC stabilization.
8. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C.
9. Chip enables (CE1 and CE2), byte enables (BHE and BLE) and BYTE (48-pin TSOP I only) need to be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other
inputs can be left floating.
Document #: 38-05445 Rev. *I
Page 4 of 21
[+] Feedback
CY62157EV30 MoBL®
Capacitance
Parameter [10]
Description
CIN
Input capacitance
COUT
Output capacitance
Test Conditions
TA = 25 °C, f = 1 MHz, VCC = VCC(typ)
Max
Unit
10
pF
10
pF
Thermal Resistance
Parameter [10]
Description
JA
Thermal resistance
(Junction to Ambient)
JC
Thermal resistance
(Junction to Case)
Test Conditions
48-ball BGA
Still air, soldered on a 3 × 4.5
inch, two-layer printed circuit
board
72
44-pin TSOP I 44-pin TSOP II Unit
74.88
76.88
C/W
8.86
8.6
13.52
C/W
Figure 4. AC Test Loads and Waveforms
R1
VCC
OUTPUT
30 pF
INCLUDING
JIG AND
SCOPE
Parameters
R1
R2
RTH
VTH
VCC
10%
GND
R2 Rise Time = 1 V/ns
ALL INPUT PULSES
90%
90%
10%
Fall Time = 1 V/ns
Equivalent to:
THÉVENIN EQUIVALENT
RTH
OUTPUT
V TH
2.5 V
16667
15385
8000
1.20
3.0 V
1103
1554
645
1.75
Unit



V
Note
10. Tested initially and after any design or process changes that may affect these parameters.
Document #: 38-05445 Rev. *I
Page 5 of 21
[+] Feedback
CY62157EV30 MoBL®
Data Retention Characteristics
Over the Operating Range
Parameter
Description
Min
Typ [11]
Max
Unit
1.5
–
–
V
Industrial/Auto-A
–
2
5
A
Auto-E
–
–
30
0
–
CY62157EV30LL-45
45
–
–
CY62157EV30LL-55
55
–
–
Conditions
VCC for data retention
VDR
ICCDR
[12]
Data retention current
tCDR [13]
Chip deselect to data
retention time
tR [14]
Operation recovery time
VCC = 1.5 V, CE1 > VCC – 0.2 V,
CE2 < 0.2 V,
(BHE and BLE) > VCC – 0.2 V,
VIN > VCC – 0.2 V or VIN < 0.2 V
ns
ns
Data Retention Waveform
Figure 5. Data Retention Waveform [15]
DATA RETENTION MODE
VCC
VCC(min)
tCDR
VDR > 1.5V
VCC(min)
tR
CE1 or
BHE.BLE
or
CE2
Notes
11. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C.
12. Chip enables (CE1 and CE2), byte enables (BHE and BLE) and BYTE (48-pin TSOP I only) need to be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec.
Other inputs can be left floating.
13. Tested initially and after any design or process changes that may affect these parameters.
14. Full device operation requires linear VCC ramp from VDR to VCC(min) > 100 s or stable at VCC(min) > 100 s.
15. BHE.BLE is the AND of both BHE and BLE. Deselect the chip by either disabling chip enable signals or by disabling both BHE and BLE.
Document #: 38-05445 Rev. *I
Page 6 of 21
[+] Feedback
CY62157EV30 MoBL®
Switching Characteristics
Over the Operating Range
Parameter [16, 17]
45 ns (Industrial/
Auto-A)
Description
55 ns (Auto-E)
Min
Max
Min
Max
Unit
Read Cycle
tRC
Read cycle time
45
–
55
–
ns
tAA
Address to data valid
–
45
–
55
ns
tOHA
Data hold from address change
10
–
10
–
ns
tACE
CE1 LOW and CE2 HIGH to data valid
–
45
–
55
ns
tDOE
OE LOW to data valid
–
22
–
25
ns
tLZOE
OE LOW to Low Z[18]
5
–
5
–
ns
Z[18, 19]
–
18
–
20
ns
CE1 LOW and CE2 HIGH to Low
Z[18]
10
–
10
–
ns
tHZCE
CE1 HIGH and CE2 LOW to High
Z[18, 19]
–
18
–
20
ns
tPU
CE1 LOW and CE2 HIGH to power up
0
–
0
–
ns
tPD
CE1 HIGH and CE2 LOW to power down
–
45
–
55
ns
tDBE
BLE/BHE LOW to data valid
–
45
–
55
ns
ns
tHZOE
tLZCE
OE HIGH to High
Z[18, 20]
tLZBE
BLE/BHE LOW to Low
5
–
10
–
tHZBE
BLE/BHE HIGH to High Z[18, 19]
–
18
–
20
ns
Write cycle time
45
–
55
–
ns
ns
Write Cycle[21]
tWC
tSCE
CE1 LOW and CE2 HIGH to write end
35
–
40
–
tAW
Address setup to write end
35
–
40
–
ns
tHA
Address hold from write end
0
–
0
–
ns
tSA
Address setup to write start
0
–
0
–
ns
ns
tPWE
WE pulse width
35
–
40
–
tBW
BLE/BHE LOW to write end
35
–
40
–
ns
tSD
Data setup to write end
25
–
25
–
ns
tHD
Data hold from write end
0
–
0
–
ns
Z[18, 19]
–
18
–
20
ns
10
–
10
–
ns
tHZWE
WE LOW to High
tLZWE
WE HIGH to Low Z[18]
Notes
16. Test conditions for all parameters other than tri-state parameters assume signal transition time of 3 ns or less, timing reference levels of VCC(typ)/2, input pulse levels
of 0 to VCC(typ), and output loading of the specified IOL/IOH as shown in the Figure 4 on page 5.
17. AC timing parameters are subject to byte enable signals (BHE or BLE) not switching when chip is disabled. See application note AN13842 for further clarification.
18. At any temperature and voltage condition, tHZCE is less than tLZCE, tHZBE is less than tLZBE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any device.
19. tHZOE, tHZCE, tHZBE, and tHZWE transitions are measured when the outputs enter a high-impedance state.
20. If both byte enables are toggled together, this value is 10 ns.
21. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE or both = VIL, and CE2 = VIH. All signals must be active to initiate a write
and any of these signals can terminate a write by going inactive. The data input setup and hold timing must be referenced to the edge of the signal that terminates
the write.
Document #: 38-05445 Rev. *I
Page 7 of 21
[+] Feedback
CY62157EV30 MoBL®
Switching Waveforms
Read Cycle No. 1 (Address Transition Controlled) [22, 23]
tRC
RC
ADDRESS
tOHA
DATA OUT
tAA
PREVIOUS DATA VALID
DATA VALID
Read Cycle No. 2 (OE Controlled) [23, 24]
ADDRESS
tRC
CE1
tPD
tHZCE
CE2
tACE
BHE/BLE
tDBE
tHZBE
tLZBE
OE
tHZOE
tDOE
DATA OUT
tLZOE
HIGH IMPEDANCE
HIGH
IMPEDANCE
DATA VALID
tLZCE
VCC
SUPPLY
CURRENT
tPU
50%
50%
ICC
ISB
Notes
22. The device is continuously selected. OE, CE1 = VIL, BHE, BLE, or both = VIL, and CE2 = VIH.
23. WE is HIGH for read cycle.
24. Address valid before or similar to CE1, BHE, BLE transition LOW and CE2 transition HIGH.
Document #: 38-05445 Rev. *I
Page 8 of 21
[+] Feedback
CY62157EV30 MoBL®
Switching Waveforms (continued)
Write Cycle No. 1 (WE Controlled) [25, 26, 27]
tWC
ADDRESS
tSCE
CE1
CE2
tAW
tHA
tSA
WE
tPWE
tBW
BHE/BLE
OE
tHD
tSD
DATA I/O
NOTE 28
VALID DATA
tHZOE
Notes
25. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE or both = VIL, and CE2 = VIH. All signals must be active to initiate
a write and any of these signals can terminate a write by going inactive. The data input setup and hold timing must be referenced to the edge of the signal that
terminates the write.
26. Data I/O is high impedance if OE = VIH.
27. If CE1 goes HIGH and CE2 goes LOW simultaneously with WE = VIH, the output remains in a high impedance state.
28. During this period, the I/Os are in output state. Do not apply input signals.
Document #: 38-05445 Rev. *I
Page 9 of 21
[+] Feedback
CY62157EV30 MoBL®
Switching Waveforms (continued)
Write Cycle No. 2 (CE1 or CE2 Controlled) [29, 30, 31]
tWC
ADDRESS
tSCE
CE1
CE2
tSA
tAW
tHA
tPWE
WE
tBW
BHE/BLE
OE
DATA I/O
tSD
NOTE 32
tHD
VALID DATA
tHZOE
Notes
29. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE or both = VIL, and CE2 = VIH. All signals must be active to initiate
a write and any of these signals can terminate a write by going inactive. The data input setup and hold timing must be referenced to the edge of the signal that
terminates the write.
30. Data I/O is high impedance if OE = VIH.
31. If CE1 goes HIGH and CE2 goes LOW simultaneously with WE = VIH, the output remains in a high impedance state.
32. During this period, the I/Os are in output state. Do not apply input signals.
Document #: 38-05445 Rev. *I
Page 10 of 21
[+] Feedback
CY62157EV30 MoBL®
Switching Waveforms (continued)
Write Cycle No. 3 (WE Controlled, OE LOW) [33]
tWC
ADDRESS
tSCE
CE1
CE2
tBW
BHE/BLE
tAW
tSA
tHA
tPWE
WE
tSD
DATA I/O
NOTE 34
tHD
VALID DATA
tHZWE
tLZWE
Notes
33. If CE1 goes HIGH and CE2 goes LOW simultaneously with WE = VIH, the output remains in a high impedance state.
34. During this period, the I/Os are in output state. Do not apply input signals.
Document #: 38-05445 Rev. *I
Page 11 of 21
[+] Feedback
CY62157EV30 MoBL®
Switching Waveforms (continued)
Write Cycle No. 4 (BHE/BLE Controlled, OE LOW) [35]
tWC
ADDRESS
CE1
CE2
tSCE
tAW
tHA
tBW
BHE/BLE
tSA
tPWE
WE
tSD
DATA I/O
NOTE 36
tHD
VALID DATA
Notes
35. If CE1 goes HIGH and CE2 goes LOW simultaneously with WE = VIH, the output remains in a high impedance state.
36. During this period, the I/Os are in output state. Do not apply input signals.
Document #: 38-05445 Rev. *I
Page 12 of 21
[+] Feedback
CY62157EV30 MoBL®
Truth Table
CE1
WE
OE
BHE
BLE
X
[37]
Mode
Power
X
X
X
X
X
[37]
High Z
Deselect/power down
Standby (ISB)
L
X
X
X
X
[37]
X
[37]
X
High Z
Deselect/power down
Standby (ISB)
X
X
H
H
High Z
Deselect/power down
Standby (ISB)
L
H
H
L
L
L
Data Out (I/O0–I/O15)
Read
Active (ICC)
L
H
H
L
H
L
Data Out (I/O0 –I/O7 );
High Z (I/O8–I/O15)
Read
Active (ICC)
L
H
H
L
L
H
High Z (I/O0–I/O7);
Data Out (I/O8–I/O15)
Read
Active (ICC)
L
H
H
H
L
H
High Z
Output disabled
Active (ICC)
L
H
H
H
H
L
High Z
Output disabled
Active (ICC)
L
H
H
H
L
L
High Z
Output disabled
Active (ICC)
L
H
L
X
L
L
Data In (I/O0–I/O15)
Write
Active (ICC)
L
H
L
X
H
L
Data In (I/O0–I/O7);
High Z (I/O8–I/O15)
Write
Active (ICC)
L
H
L
X
L
H
High Z (I/O0–I/O7);
Data In (I/O8–I/O15)
Write
Active (ICC)
H
CE2
Inputs/Outputs
Note
37. The ‘X’ (Don’t care) state for the Chip enables in the truth table refer to the logic state (either HIGH or LOW). Intermediate voltage levels on these pins is not permitted
Document #: 38-05445 Rev. *I
Page 13 of 21
[+] Feedback
CY62157EV30 MoBL®
Ordering Information
Speed
(ns)
45
55
Ordering Code
Package
Diagram
CY62157EV30LL-45BVI
51-85150
48-ball very fine-pitch ball grid array
CY62157EV30LL-45BVXI
51-85150
48-ball very fine-pitch ball grid array (Pb-free)
CY62157EV30LL-45ZSXI
51-85087
44-pin thin small outline package type II (Pb-free)
CY62157EV30LL-45ZXI
51-85183
48-pin thin small outline package type I (Pb-free)
CY62157EV30LL-45BVXA
51-85150
48-ball very fine-pitch ball grid array (Pb-free)
CY62157EV30LL-45ZSXA
51-85087
44-pin thin small outline package type II (Pb-free)
CY62157EV30LL-45ZXA
51-85183
48-pin thin small outline package type I (Pb-free)
CY62157EV30LL-55ZSXE
51-85087
44-pin thin small outline package type II (Pb-free)
CY62157EV30LL-55ZXE
51-85183
48-pin thin small outline package type I (Pb-free)
Package Type
Operating
Range
Industrial
Automotive-A
Automotive-E
Contact your local Cypress sales representative for availability of these parts.
Ordering Code Definitions
CY 621 5
7
E V30 LL -
XX XX
X
X
Temperature Range: X = I or A or E
I = Industrial; A = Automotive-A; E = Automotive-E
Pb-free
Package Type: XX = BV or ZS or Z
BV = 48-ball VFBGA
ZS = 44-pin TSOP II
Z = 48-pin TSOP I
Speed Grade: XX = 45 ns or 55 ns
Low Power
Voltage
E = Process Technology 90 nm
Buswidth = × 16
Density = 8-Mbit
Family Code: MoBL SRAM family
Company ID: CY = Cypress
Document #: 38-05445 Rev. *I
Page 14 of 21
[+] Feedback
CY62157EV30 MoBL®
Package Diagrams
Figure 6. 48-pin VFBGA (6 × 8 × 1 mm) BV48/BZ48, 51-85150
51-85150 *F
Document #: 38-05445 Rev. *I
Page 15 of 21
[+] Feedback
CY62157EV30 MoBL®
Package Diagrams (continued)
Figure 7. 44-pin TSOP Z44-II, 51-85087
51-85087 *C
Document #: 38-05445 Rev. *I
Page 16 of 21
[+] Feedback
CY62157EV30 MoBL®
Package Diagrams (continued)
Figure 8. 48-pin TSOP I (12 × 18.4 × 1.0 mm) Z48A, 51-85183
51-85183 *B
Document #: 38-05445 Rev. *I
Page 17 of 21
[+] Feedback
CY62157EV30 MoBL®
Acronyms
Acronym
Document Conventions
Description
Units of Measure
CE
chip enable
CMOS
complementary metal oxide semiconductor
°C
degree Celcius
I/O
input/output
MHz
Mega Hertz
OE
output enable
μA
micro Amperes
RAM
random access memory
μs
micro seconds
SRAM
static random access memory
mA
milli Amperes
TSOP
thin small outline package
mm
milli meter
VFBGA
very fine-pitch ball grid array
ns
nano seconds
WE
write enable

ohms
%
percent
pF
pico Farad
V
Volts
W
Watts
Document #: 38-05445 Rev. *I
Symbol
Unit of Measure
Page 18 of 21
[+] Feedback
CY62157EV30 MoBL®
Document History Page
Document Title: CY62157EV30 MoBL®, 8-Mbit (512 K × 16) Static RAM
Document Number: 38-05445
Rev.
ECN No.
Orig. of
Change
Submission
Date
**
202940
AJU
See ECN
New Data Sheet
*A
291272
SYT
See ECN
Converted from Advance Information to Preliminary
Removed 48-TSOP I Package and the associated footnote
Added footnote stating 44 TSOP II Package has only one CE on Page # 2
Changed VCC stabilization time in footnote #7 from 100 s to 200 s
Changed ICCDR from 4 to 4.5 A
Changed tOHA from 6 to 10 ns for both 35 and 45 ns Speed Bins
Changed tDOE from 15 to 18 ns for 35 ns Speed Bin
Changed tHZOE, tHZBE and tHZWE from 12 and 15 ns to 15 and 18 ns for 35 and 45
ns Speed Bins respectively
Changed tHZCE from 12 and 15 ns to 18 and 22 ns for 35 and 45 ns Speed Bins
respectively
Changed tSCE, tAW and tBW from 25 and 40 ns to 30 and 35 ns for 35 and 45 ns Speed
Bins respectively
Changed tSD from 15 and 20 ns to 18 and 22 ns for 35 and 45 ns Speed Bins respectively
Added Lead-Free Package Information
*B
444306
NXR
See ECN
Converted from Preliminary to Final.
Changed ball E3 from DNU to NC
Removed redundant footnote on DNU.
Removed 35 ns speed bin
Removed “L” bin
Added 48 pin TSOP I package
Added Automotive product information.
Changed the ICC Typ value from 16 mA to 18 mA and ICC Max value from 28 mA
to 25 mA for test condition f = fax = 1/tRC.
Changed the ICC Max value from 2.3 mA to 3 mA for test condition f = 1MHz.
Changed the ISB1 and ISB2 Max value from 4.5 A to 8 A and Typ value from 0.9
A to 2 A respectively.
Modified ISB1 test condition to include BHE, BLE
Updated Thermal Resistance table.
Changed Test Load Capacitance from 50 pF to 30 pF.
Added Typ value for ICCDR .
Changed the ICCDR Max value from 4.5 A to 5 A
Corrected tR in Data Retention Characteristics from 100 s to tRC ns.
Changed tLZOE from 3 to 5
Changed tLZCE from 6 to 10
Changed tHZCE from 22 to 18
Changed tLZBE from 6 to 5
Changed tPWE from 30 to 35
Changed tSD from 22 to 25
Changed tLZWE from 6 to 10
Added footnote #15
Updated the ordering Information and replaced the Package Name column with
Package Diagram.
*C
467052
NXR
See ECN
Modified Data sheet to include x8 configurability.
Updated the Ordering Information table
*D
925501
VKN
See ECN
Removed Automotive-E information
Added Preliminary Automotive-A information
Added footnote #10 related to ISB2 and ICCDR
Added footnote #15 related AC timing parameters
*E
1045801
VKN
See ECN
Converted Automotive-A specs from preliminary to final
Updated footnote #9
Document #: 38-05445 Rev. *I
Description of Change
Page 19 of 21
[+] Feedback
CY62157EV30 MoBL®
Document History Page (continued)
Document Title: CY62157EV30 MoBL®, 8-Mbit (512 K × 16) Static RAM
Document Number: 38-05445
Rev.
ECN No.
Orig. of
Change
Submission
Date
*F
2724889
NXR/AESA
06/26/09
*G
2927528
VKN
*H
3110053
PRAS
12/14/2010 Changed Table Footnotes to Footnotes.
Added Ordering Code Definitions.
*I
3269771
RAME
05/30/2011 Updated Functional Description (Removed “For best practice recommendations,
refer to the Cypress application note AN1064, SRAM System Guidelines.”).
Updated Electrical Characteristics.
Updated Data Retention Characteristics.
Updated Package Diagrams.
Added Acronyms and Units of Measure.
Updated in new template.
Document #: 38-05445 Rev. *I
Description of Change
Added Automotive-E information
Included -45ZXA/-55ZSXE/-55ZXE parts in the Ordering Information table
05/04/2010 Renamed “DNU” pins as “NC” for 48 TSOP I package
Added footnote #24 related to chip enable
Updated Package Diagrams
Added Contents
Updated links in Sales, Solutions, and Legal Information
Page 20 of 21
[+] Feedback
CY62157EV30 MoBL®
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2004-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 38-05445 Rev. *I
Revised May 30, 2011
Page 21 of 21
MoBL is a registered trademark and More Battery Life is a trademark of Cypress Semiconductor. All products and company names mentioned in this document may be the trademarks of their respective
holders.
[+] Feedback
Similar pages