Coilcraft DO1605T-474ML Smt power inductor Datasheet

Document 253-1
SMT Power Inductors – DO1605T Series
• Only 1.8 mm high
• Handles current up to 2.3 Amps rms
Designer’s Kit C353 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 101 – 110 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.25 mm thick, 8 mm pocket spacing, 2.3 mm pocket depth
PCB washing Only pure water or alcohol recommended
1
Part number1
DO1605T-102ML_
DO1605T-152ML_
DO1605T-222ML_
DO1605T-332ML_
DO1605T-472ML_
DO1605T-682ML_
DO1605T-822ML_
DO1605T-103ML_
DO1605T-153ML_
DO1605T-223ML_
DO1605T-333ML_
DO1605T-473ML_
DO1605T-683ML_
DO1605T-104ML_
DO1605T-154ML_
DO1605T-224ML_
DO1605T-334ML_
DO1605T-474ML_
DO1605T-684ML_
DO1605T-105ML_
1 2
L
±20%
(µH)
DCR
max
(Ohms)
SRF3
ref
(MHz)
1.0
1.5
2.2
3.3
4.7
6.8
8.2
10
15
22
33
47
68
100
150
220
330
470
680
1000
0.04
0.06
0.07
0.12
0.15
0.20
0.23
0.27
0.35
0.54
0.74
1.1
1.6
2.3
3.5
5.7
8.2
10.8
17.2
22.6
230
180
140
110
100
80
70
60
45
35
30
22
20
15
10
9
8
7
5
4
1. When ordering, please specify termination and packaging codes:
Isat4
(A)
Irms5
(A)
2.5
2.2
1.8
1.4
1.2
1.1
1.0
1.0
0.8
0.6
0.5
0.45
0.35
0.30
0.25
0.20
0.16
0.14
0.12
0.08
2.3
2.1
1.7
1.3
1.1
1.0
0.95
0.90
0.70
0.50
0.45
0.40
0.35
0.30
0.25
0.18
0.16
0.12
0.10
0.08
DO1605T-105MLC
Termination: L = RoHS compliant silver-palladium-platinum-glass frit
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B= Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D= 13″ machine-ready reel. EIA-481 embossed plastic
tape (3500 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms.
3. SRF >13 MHz measured using Agilent/HP 8753D network analyzer;
<13 MHz using Agilent/HP 4192A.
4. DC current at which the inductance drops 10% (typ) from its value
without current.
5. Current that causes a 40°C temperature rise from 25°C ambient.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 253-1
Revised 10/08/08
Document 253-2
SMT Power Inductors – DO1605T Series
Typical L vs Frequency
Typical L vs Current
10000
10000
1000 µH
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
100 µH
100
10 µH
10
10 µH
10
1 µH
1 µH
1
100 µH
100
1
0.1
0.1
0.01
1
0.1
10
0.01
10
Current (A)
XXXX
Irms Derating
120
110
100
Internal
code
Dash
number
90
0.216 max
5,5
80
70
0.071max
1,8
60
Recommended
Land Pattern
50
0.039
1,0
40
25°C
Percent of rated Irms
1
0.1
Frequency (MHz)
30
20
0.165 max
4,2
10
0.173
4,4
0
-40
-20
0
20
40
60
80
Ambient temperature (°C)
100
120 140
0.148
3,76
Dimensions are
in
0.029
0,74
inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
0.187
4,76
Document 253-2
Revised 10/08/08
Similar pages