TT OPL811-OC Photologic hermetic sensor Datasheet

OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC,
OPL813-OC, OPL820, OPL820-OC, OPL821-OC
Features:





Four output options available
High noise immunity
Direct TTL/LSTTL interface
TO-18 hermetically sealed package
Sensors mechanically and spectrally matched to other Optek devices (see device
descriptions detailed below)
Description:
All OPL800, OPL801, OPL820 and OPL821 sensors consist of a photodiode, a linear amplifier and a Schmitt trigger on a single
silicon chip (monolithic chip for OPL820 and OPL821). OPL810, OPL811, OPL812 and OPL813 sensors also have a voltage
regulator added to their photologic chips. Each device’s photologic chip is mounted onto a standard TO-18 header and
hermetically sealed in a lensed metal can.
All devices in the series feature TTL/LSTTL compatible logic level output, which can drive up to 8 TTL loads (OPL800, OPL801)
or up to 10 TTL loads (OPL810, OPL811, OPL812, OPL813, OPL820 and OPL821) without additional circuitry. On all these
devices, the Schmitt trigger’s hysteresis characteristics provide high immunity to noise on input and V CC.
OPL800 series devices feature medium-speed data rates to 250 kBaud, with typical rise and fall times of 25 nanoseconds.
OPL800 and OPL801 devices are mechanically and spectrally matched to OP130 and OP231 series LEDs. OPL810, OPL811,
OPL812 and OPL813 devices are mechanically and spectrally matched to OP130 and OP230 series devices. OPL820 and
OPL821 devices are mechanically and spectrally matched to OP130 and OP231 series LEDs.
Applications:






Non-contact reflective object sensor
Assembly line automation
Machine automation
Machine safety
End of travel sensor
Door sensor
Pin #
OPL80_ or
OPL81_
OPL82_
Transistor
1
Ground
Ground
Collector
2
VCC
Output
Base
3
Output
VCC
Emitter
TO-18 Base
Mounted to TO-18 Base
DIMENSIONS ARE IN:
[ MILLIMETERS]
INCHES
RoHS
Pin #
OPL80_ or OPL81_
1
General Note
TT Electronics reserves the right to make changes in product specification without
2
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
3
© TT electronics plc
Ground
Vcc
Output
OPL82_
Transistor
Ground
Collector
TT Electronics | OPTEK Technology, Inc.
Output1645 Wallace Drive,
Base Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Vcc
Emitter
Issue A 08/2016 Page 1
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Ordering Information
Part Number
Photologic®
OPL800
Totem-Pole
OPL800-OC
Open-Collector
OPL801
Inv-Totem-Pole
OPL801-OC
Inv-Open-Collector
OPL810
Totem-Pole
OPL810-OC
Open-Collector
OPL811
Inv-Totem-Pole
OPL811-OC
Inv-Open-Collector
OPL812-OC
Open-Collector
OPL813-OC
Inv-Open-Collector
OPL820
10K Pull-Up
OPL820-OC
Open Collector
OPL821-OC
Inv. Open Collector
Input Power EE
(µW/cm2) Min / Max
VCC (V)
Min / Max
50 / 600
5 / 100
IOH / IOL
Lead Length
0.10 / 12.8
4.5 / 16.0
0.50"
0.10 / 16.0
2 / 35
OPL800, OPL800OC, OPL801, OPL801-OC, OPL810, OPL810-OC,
OPL811, OPL811-OC, OPL812-OC, OPL813-OC, OPL820-OC, OPL821-OC
OPL800/800B/810 Buffered Totem-Pole
OPL800-OC/810-OC/812-OC/820/OC Open-Collector
VCC
VCC
OUT
OUT
GND
OPL801/811 Inverted Totem-Pole
GND
OPL801-OC/811-OC/813-OC/821-OC Inverted Open-Collector
VCC
VCC
OUT
OUT
GND
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
GND
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 2
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
OPL820
OPL820 10K Pull-Up
OPL821 Inverted 10K Pull-Up
VCC
VCC
OUT
OUT
GND
GND
VCC
VCC
OUT
OUT
GND
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
GND
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 3
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Electrical Specifications
Absolute Maximum Ratings (TA = 25° C unless otherwise noted)
OPB800/801/810/811 and OPB800-OC Series
Input Diode
Operating Temperature Range
OPL800, OPL801
OPL810, OPL811
OPL820
-55° C to +110° C
-55° C to +105° C
-40° C to +100° C
Storage Temperature Range
OPL800, OPL801
OPL810, OPL811
OPL820
-65° C to +150° C
-65° C to +125° C
-55° C to +125° C
260°C(1)
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
Input Infrared LED
Supply Voltage, VCC (not to exceed 3 seconds)
OPL800, OPL801
OPL810, OPL811, OPL820
10 V
18 V
Sourcing Current
OPL810, OPL811
10 mA
Output Voltage (high state)
OPL800, OPL801, OPL810, OPL811
OPL810, OPL811
OPL820
35 V
50 mA
30 V
Output Current Sink (low state)
OPL810, OPL811
OPL820
50 mA
16 mA
Irradiance
OPL800, OPL801
OPL810, OPL810-OC, OPL811, OPL811-OC
OPL812, OPL812-OC, OPL813, OPL813-OC
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
3 mW/cm2
2 mW/cm2
1 mW/cm2
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 4
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Electrical Specifications
Absolute Maximum Ratings (TA = 25° C unless otherwise noted)
OPB800/801/810/811/812/813 and OPB800-OC Series
Output Photologic®
Voltage at Output Lead
OPL800, OPL801, OPL810, OPL811
OPL820
35 V
30 V
Duration of Output Short to VCC
1 second
Power Dissipation
OPL800, OPL801
OPL810, OPL811
OPL820
120 mW(2)
250 mW(2)
200 mW(2)
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPB820, a maximum of 20
grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.5 mW/°C above 25° C for OPL800, OPL801, OPL810, OPL811. Derate linearly 5.7 mW/°C above 90° C for
OPL820.
(3) For OPL800, OPL801, OPL810, OPL811, light measurements are made with λi = 935 nm. For OPB820, light measurements
are made with an LED source having a wavelength of 935 nm.
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 5
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Electrical Specifications
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
4.5
4.5
4.5
-
5.5
16
16
V
V
V
-
Peak-to-Peak VCC Ripple Necessary to
Cause False Triggering of Output
OPL800/801
OPL810/811
-
2
-
1
V
V
Supply Current
-
-
15
mA
Operating Supply Voltage
OPL800/801
OPL810/811
OP820
VCC
ICC
EeT(+)
Positive-Going Threshold Irradiance(3)
OPL800/801
OPL810/811
OPL820
f = DC to 50 MHz
f = DC to 50 MHz
Ee = 0 or 1 mW/cm2
0.050 0.180 0.600 mW/cm2 TA = 25°C
0.015 0.060 0.200 mW/cm2 TA = 25°C
0.002 0.015 0.035 mW/cm2 See below(3)
EeT(+)/EeT(-)
Hysteresis Ratio
OPL800/801
OPL810/811
1.5
1.2
2.0
1.5
2.5
2.0
-
Ee(+)/Ee(-)
Hysteresis Ratio
OPL820
1.05
1.20
1.90
-
See below(3)
-
ICCH
High State Supply Current
OPL820
-
5
12
mA
See below(4)
ICCL
Low State Supply Current
OPL820
-
4
12
mA
See below(5)
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 6
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Electrical Specifications
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
VOH
PARAMETER
High Level Output Voltage
OPL800
OPL801
OPL810
OPL811
OPL820-OC/821-OC
MIN
TYP
MAX
UNITS
2.4
2.4
VCC-2.1
VCC-2.1
VCC-1.5
-
VCC
V
V
V
V
V
TEST CONDITIONS
IOH = -800 µA, Ee = 1 mW/cm2
IOH = -800 µA, Ee = 0
IOH = -1mA, Ee = 0.4 mW/cm2
IOH = -1mA, Ee = 0
IOH = -100 µA(4)
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPB820, a maximum of 20
grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.5 mW/°C above 25° C for OPL800, OPL801, OPL810, OPL811. Derate linearly 5.7 mW/°C above 90° C for
OPL820.
(3) For OPL800, OPL801, OPL810, OPL811, light measurements are made with λi = 935 nm. For OPB820, light measurements
are made with an LED source having a wavelength of 935 nm.
(4) High output state limits are valid for 4.5 V < VCC < 16 V and Ee > 0.035 mW/cm2 (OPL820, OPL820-OC), Ee < 0.001 mW/cm2
(OPL821-OC).
(5) Low output state limits are valid for 4.5 V < VCC < 16 V and Ee > 0.035 mW/cm2 (OPL821-OC), Ee < 0.001 mW/cm2 (OPL820,
OPL820-OC).
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 7
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Electrical Specifications
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
VOH
High Level Output Voltage
OPL800
OPL801
OPL810
OPL811
OPL820-OC/821-OC
2.4
2.4
VCC-2.1
VCC-2.1
VCC-1.5
-
VCC
V
V
V
V
V
IOH = -800 µA, Ee = 1 mW/cm2
IOH = -800 µA, Ee = 0
IOH = -1mA, Ee = 0.4 mW/cm2
IOH = -1mA, Ee = 0
IOH = -100 µA(4)
VOL
Low Level Output Voltage
OPL800/800-OC
OPL801/801-OC
OPL810/810-OC
OPL811/811-OC
OPL812-OC
OPL813-OC
OPL820
-
-
0.4
0.4
0.4
0.4
0.4
0.4
0.4
V
V
V
V
V
V
V
IOL = 12.8 mA, Ee = 0
IOL = 12.8 mA, Ee = 1 mW/cm2
IOL = 16 mA, Ee = 0
IOL = 16 mA, Ee = 0.4 mW/cm2
IOL = 16 mA, Ee = 0
IOL = 16 mA, Ee = 0.2 mW/cm2
IOL = 16 mA(5)
IOH
High Level Output Current
OPL800-OC
OPL801-OC
OPL810-OC
OPL811-OC
OPL812-OC
OPL813-OC
-
-
100
100
100
100
100
100
µA
µA
µA
µA
µA
µA
VOH = 30 V, Ee = 2 mW/cm2
VOH = 30 V, Ee = 0
VOH = 30 V, Ee = 0.4 mW/cm2
VOH = 30 V, Ee = 0
VOH = 30 V, Ee = 0.2 mW/cm2
VOH = 30 V, Ee = 0
IOS
Short Circuit Output Current
OPL800
OPL801
-100
mA
mA
Ee = 1 mW/cm2, Output = GND
Ee = 0, Output = GND
-20
-
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TEST CONDITIONS
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 8
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Electrical Specifications
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Output Rise Time, Fall Time
OPL800/801
-
70
-
ns
OPL800-OC/801-OC
-
70
-
ns
OPL810/811
-
70
-
ns
OPL810-OC/811-OC/812-OC/
813-OC
-
100
-
ns
TA = 25°C, Ee = 0 or 1 mW/cm2, RL = 8
TTL loads, f = 10 kHz, D.C. = 50%
TA = 25°C, Ee = 0 or 1 mW/cm2, RL =
360 Ω, f = 10 kHz, D.C. = 50%
TA = 25°C, Ee = 0 or 0.4 mW/cm2, RL =
10 TTL loads, f = 10 kHz, D.C. = 50%
TA = 25°C, Ee = 0 or 1 mW/cm2, RL =
300 Ω, f = 10 kHz, D.C. = 50%
OPL820
-
60
-
ns
RL = 390Ω
-
5
-
µs
-
5
-
µs
-
5
-
µs
-
5
-
µs
-
1
2.1
-
µs
µs
TA = 25°C, Ee = 0 or 1 mW/cm2, RL = 8
TTL loads, f = 10 kHz, D.C. = 50%
TA = 25°C, Ee = 0 or 1 mW/cm2, RL = 8
TTL loads, f = 10 kHz, D.C. = 50%
TA = 25°C, Ee = 0 or 0.4 mW/cm2, RL =
10 TTL loads, f = 10 kHz, D.C. = 50%
TA = 25°C, Ee = 0 or 1 mW/cm2, RL =
300 Ω, f = 10 kHz, D.C. = 50%
EE = 0.1 mW/cm2, RL = 390 Ω
EE = 01 mW/cm2, RL = 390 Ω
-
100
-
kHz
EE = 01 mW/cm2, RL = 390 Ω
t r, tf
Propagation Delay
Low/High - High/Low
OPL800/801
OPL800-OC/801-OC
tPLH, tPHL
OPL810/811
OPL810-OC/811-OC/812-OC/
813-OC
OPL820 (to high state)
OPL820 (to low state)
Data Rate Data Rate Using NRZ Format
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPB820, a maximum of 20
grams force may be applied to leads while at soldering temperatures.
(2) Derate linearly 2.5 mW/°C above 25° C for OPL800, OPL801, OPL810, OPL811. Derate linearly 5.7 mW/°C above 90° C for
OPL820.
(3) For OPL800, OPL801, OPL810, OPL811, light measurements are made with λi = 935 nm. For OPB820, light measurements
are made with an LED source having a wavelength of 935 nm.
(4) High output state limits are valid for 4.5 V < VCC < 16 V and Ee > 0.035 mW/cm2 (OPL820, OPL820-OC), Ee < 0.001 mW/cm2
(OPL821-OC).
(5) Low output state limits are valid for 4.5 V < VCC < 16 V and Ee > 0.035 mW/cm2 (OPL821-OC), Ee < 0.001 mW/cm2 (OPL820,
OPL820-OC).
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 9
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Performance
OPL800, OPL801
OPL800-OC, OPL801-OC
OPL800, OPL800-OC
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
OPL801, OPL801-OC
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 10
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Performance
OPL800, OPL801 Series
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 11
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Performance
OPL810, OPL811 Series
OPL812, OPL813 Series
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 12
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Performance
OPL812, OPL813 Series
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 13
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Performance
OPL820, OPL821 Series
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 14
OPL800, OPL800-OC, OPL801, OPL801-OC, OPL810,
OPL810-OC, OPL811, OPL811-OC, OPL812-OC, OPL813OC, OPL820, OPL820-OC, OPL821-OC
Performance
OPL820, OPL821 Series
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
TT Electronics | OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
[email protected] | www.ttelectronics.com
Issue A
08/2016
Page 15
Similar pages