NSC LM3410XMYX 525khz/1.6mhz, constant current boost and sepic led driver with internal compensation Datasheet

October 2007
LM3410
525kHz/1.6MHz, Constant Current Boost and SEPIC LED
Driver with Internal Compensation
General Description
Features
The LM3410 constant current LED driver is a monolithic, high
frequency, PWM step-up DC/DC converter in 5-pin SOT23,
6-pin LLP, & 8-pin eMSOP packages. With a minimum of external components the LM3410 is easy to use. It can drive
2.5A typical peak currents with an internal 160mΩ NMOS
switch. Switching frequency is internally set to either 525kHz
or 1.60MHz, allowing the use of extremely small surface
mount inductors and chip capacitors. Even though the operating frequency is high, efficiencies up to 88% are easy to
achieve. External shutdown is included, featuring an ultra-low
stand-by current of 80nA. The LM3410 utilizes current-mode
control and internal compensation to provide high-performance over a wide range of operating conditions. Additional
features include dimming, pulse-by-pulse current limit, and
thermal shutdown.
■
■
■
■
■
■
■
■
■
Space Saving SOT23-5 & 6-LLP Package
Wide Input voltage range of 2.7V to 5.5V
Wide Output voltage range of 3V to 24V
2.1A switch current over full temperature range
Two High Switching Frequencies Available:
— 525 kHz (LM3410-Y)
— 1.6 MHz (LM3410-X)
160 mΩ NMOS Switch
190 mV Internal Voltage Reference
Internal Soft-Start
Current-Mode, PWM Operation
Applications
■
■
■
■
Portable Illumination
LED Backlight Current Source
LiIon Backlight OLED Driver
Handheld Devices
Typical Boost Application Circuit
30038501
© 2007 National Semiconductor Corporation
300385
www.national.com
LM3410 525kHz/1.6MHz, Constant Current Boost and SEPIC LED Driver
ADVANCE INFORMATION
LM3410
Connection Diagrams
Top View
Top View
Top View
30038503
5-Pin SOT23
30038505
8-Pin eMSOP
30038504
6-Pin LLP
Ordering Information
Frequency
Order Number
LM3410YMF
LM3410YMFX
525 kHz
LM3410YSD
LM3410YSDX
LM3410YMY
LM3410YMYX
LM3410XMF
LM3410XMFX
1.6 MHz
LM3410XSD
LM3410XSDX
LM3410XMY
LM3410XMYX
www.national.com
Package Type
Package Drawing
SOT23-5
MF05A
LLP-6
SDE06A
eMSOP-8
MUY08A
SOT23-5
MF05A
LLP-6
SDE06A
eMSOP-8
MUY08A
2
Supplied As
1000 units tape & reel
3000 units tape & reel
1000 units tape & reel
4500 units tape & reel
1000 units tape & reel
3500 units tape & reel
1000 units tape & reel
3000 units tape & reel
1000 units tape & reel
4500 units tape & reel
1000 units tape & reel
3500 units tape & reel
LM3410
Pin Description - 5-Pin SOT23
Pin
Name
1
SW
Function
2
GND
3
FB
Feedback pin. Connect FB to external resistor divider to set output voltage.
4
DIM
Dimming & shutdown control input. Logic high enables operation. Duty Cycle from 0 to 100%. Do not allow
this pin to float or be greater than VIN + 0.3V.
5
VIN
Supply voltage for power stage, and input supply voltage.
Output switch. Connect to the inductor, output diode.
Signal and power ground pin. Place the bottom resistor of the feedback network as close as possible to this
pin.
Pin Description - 6 Pin LLP
Pin
Name
Function
1
PGND
Power ground pin. Place PGND and output capacitor GND close together.
2
VIN
Supply voltage for power stage, and input supply voltage.
3
DIM
Dimming & shutdown control input. Logic high enables operation. Duty Cycle from 0 to 100%. Do not allow
this pin to float or be greater than VIN + 0.3V.
4
FB
Feedback pin. Connect FB to external resistor divider to set output voltage.
5
AGND
6
SW
DAP
GND
Signal ground pin. Place the bottom resistor of the feedback network as close as possible to this pin & pin
4.
Output switch. Connect to the inductor, output diode.
Signal & Power ground. Connect to pin 1 & pin 5 on top layer. Place 4-6 vias from DAP to bottom layer GND
plane.
Pin Description - 8 Pin eMSOP
Pin
Name
1
-
Function
2
PGND
3
VIN
Supply voltage for power stage, and input supply voltage.
4
DIM
Dimming & shutdown control input. Logic high enables operation. Duty Cycle from 0 to 100%. Do not allow
this pin to float or be greater than VIN + 0.3V.
5
FB
Feedback pin. Connect FB to external resistor divider to set output voltage.
6
AGND
7
SW
8
-
DAP
GND
No Connect
Power ground pin. Place PGND and output capacitor GND close together.
Signal ground pin. Place the bottom resistor of the feedback network as close as possible to this pin & pin 5
Output switch. Connect to the inductor, output diode.
No Connect
Signal & Power ground. Connect to pin 2 & pin 6 on top layer. Place 4-6 vias from DAP to bottom layer GND
plane.
3
www.national.com
LM3410
Physical Dimensions inches (millimeters) unless otherwise noted
6-Lead LLP Package
NS Package Number SDE06A
5-Lead SOT23-5 Package
NS Package Number MF05A
www.national.com
4
LM3410
8-Lead eMSOP Package
NS Package Number MUY08A
5
www.national.com
LM3410 525kHz/1.6MHz, Constant Current Boost and SEPIC LED Driver
Notes
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2007 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Customer
Support Center
Email:
[email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Customer Support Center
Fax: +49 (0) 180-530-85-86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +49 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor Asia
Pacific Customer Support Center
Email: [email protected]
National Semiconductor Japan
Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
Similar pages