NSC LP3999ITLX-2.6NOPB Low noise 150ma voltage regulator for rf/analog application Datasheet

LP3999
Low Noise 150mA Voltage Regulator for RF/Analog
Applications
General Description
Key Specifications
The LP3999 regulator is designed to meet the requirements
of portable wireless battery-powered applications and will
provide an accurate output voltage with low noise and low
quiescent current. Ideally suited for powering RF/Analog
devices this device will also be used to meet more general
circuit requirements.
n
n
n
n
n
n
n
n
For battery powered applications the low dropout and low
ground current provided by the device allows the lifetime of
the battery to be maximized.The inclusion of an Enable(disable) control can be used by the system to further extend the
battery lifetime by reducing the power consumption to virtually zero. Should the application require a device with an
active disable function please refer to device LP3995.
The LP3999 also features internal protection against shortcircuit currents and over-temperature conditions.
The LP3999 is designed to be stable with small 1.0 µF
ceramic capacitors. The small outline of the LP3999 micro
SMD package with the required ceramic capacitors can
realize a system application within minimal board area.
Performance is specified for a −40˚C to +125˚C temperature
range.
The device is available in micro SMD package and LLP
package. For other package options contact your local NSC
sales office.
The device is available in fixed output voltages in the ranges
of 1.5V to 3.3V. For availability, please contact your local
NSC sales office.
2.5V to 6.0V Input Range
Accurate Output Voltage; ± 75mV / 2%
60 mV Typical Dropout with 150 mA Load. Vout > 2.5V
Virtually Zero Quiescent Current when Disabled
10 µVrms output noise over 10Hz to 100kHz
Stable with a 1 µF Output Capacitor
Guaranteed 150 mA Output Current
Fast Turn-on Time; 140 µs (Typ.)
Features
n
n
n
n
n
n
n
5 pin micro SMD Package
6 pin LLP Package
Stable with Ceramic Capacitor
Logic Controlled Enable
Fast Turn-on
Thermal-overload and short-circuit protection
−40 to +125˚C junction temperature range for operation
Applications
n
n
n
n
n
n
GSM Portable Phones
CDMA Cellular Handsets
Wideband CDMA Cellular Handsets
Bluetooth Devices
Portable Information Appliances
Handheld MP3 Devices
Typical Application Circuit
20052001
© 2003 National Semiconductor Corporation
DS200520
www.national.com
LP3999 Low Noise 150mA Voltage Regulator for RF/Analog Applications
December 2003
LP3999
Block Diagram
20052002
Pin Description
Package 5 pin micro SMD
Pin No.
Symbol
micro
SMD
LLP
A1
3
VEN
Name and Function
Enable Input; Disables the Regulator when ≤ 0.4V.
Enables the regulator when ≥ 0.9V
B2
2
GND
Common Ground
C1
6
VOUT
Voltage output. Connect this output to the load circuit.
C3
1
VIN
A3
4
CBYPASS
www.national.com
Voltage Supply Input
Bypass Capacitor connection.
Connect a 0.01 µF capacitor for noise reduction.
5
N/C
No internal connection. There should not be any board connection to this pin.
Pad
GND
Ground connection.
Connect to ground plane for best thermal conduction.
2
LP3999
Connection Diagrams
micro SMD, 5 Bump Package
20052003
See NS Package Number TLA05
LLP-6 Package (SOT23 footprint)
20052004
See NS Package Number LDE06A
3
www.national.com
LP3999
Ordering Information
For micro SMD Package
Output Voltage
(V)
Grade
LP3999 Supplied as 250
Units, Tape and Reel
LP3999 Supplied as
3000 Units, Tape and
Reel
1.5
STD
LP3999ITL-1.5
LP3999ITLX-1.5
1.6 (Note 2)
STD
LP3999ITL-1.6
LP3999ITLX-1.6
1.7(Note 2)
STD
LP3999ITL-1.7
LP3999ITLX-1.7
1.8
STD
LP3999ITL-1.8
LP3999ITLX-1.8
1.875
STD
LP3999ITL-1.875
LP3999ITLX-1.875
1.9 (Note 2)
STD
LP3999ITL-1.9
LP3999ITLX-1.9
2.0(Note 2)
STD
LP3999ITL-2.0
LP3999ITLX-2.0
2.1 (Note 2)
STD
LP3999ITL-2.1
LP3999ITLX-2.1
2.2(Note 2)
STD
LP3999ITL-2.2
LP3999ITLX-2.2
2.4
STD
LP3999ITL-2.4
LP3999ITLX-2.4
2.5
STD
LP3999ITL-2.5
LP3999ITLX-2.5
2.6(Note 2)
STD
LP3999ITL-2.6
LP3999ITLX-2.6
2.8
STD
LP3999ITL-2.8
LP3999ITLX-2.8
3.0(Note 2)
STD
LP3999ITL-3.0
LP3999ITLX-3.0
3.3
STD
LP3999ITL-3.3
LP3999ITLX-3.3
Package
Marking
For micro SMD Package UNLEADED
Output Voltage
(V)
Grade
LP3999 Supplied as 250
Units, Tape and Reel
LP3999 Supplied as
3000 Units, Tape and
Reel
1.5 (Note 2)
STD
LP3999ITL-1.5 NOPB
LP3999ITLX-1.5 NOPB
1.6 (Note 2)
STD
LP3999ITL-1.6 NOPB
LP3999ITLX-1.6 NOPB
1.7 (Note 2)
STD
LP3999ITL-1.7 NOPB
LP3999ITLX-1.7 NOPB
1.8 (Note 2)
STD
LP3999ITL-1.8 NOPB
LP3999ITLX-1.8 NOPB
1.875 (Note 2)
STD
LP3999ITL-1.875 NOPB
LP3999ITLX-1.875 NOPB
1.9 (Note 2)
STD
LP3999ITL-1.9 NOPB
LP3999ITLX-1.9 NOPB
2.0(Note 2)
STD
LP3999ITL-2.0 NOPB
LP3999ITLX-2.0 NOPB
2.1 (Note 2)
STD
LP3999ITL-2.1 NOPB
LP3999ITLX-2.1 NOPB
2.2(Note 2)
STD
LP3999ITL-2.2 NOPB
LP3999ITLX-2.2 NOPB
2.4 (Note 2)
STD
LP3999ITL-2.4 NOPB
LP3999ITLX-2.4 NOPB
2.5 (Note 2)
STD
LP3999ITL-2.5 NOPB
LP3999ITLX-2.5 NOPB
2.6(Note 2)
STD
LP3999ITL-2.6 NOPB
LP3999ITLX-2.6 NOPB
2.8 (Note 2)
STD
LP3999ITL-2.8 NOPB
LP3999ITLX-2.8 NOPB
3.0(Note 2)
STD
LP3999ITL-3.0 NOPB
LP3999ITLX-3.0 NOPB
3.3(Note 2)
STD
LP3999ITL-3.3 NOPB
LP3999ITLX-3.3 NOPB
www.national.com
4
Package
Marking
LP3999
Ordering Information
(Continued)
For LLP-6 Package
Output Voltage
(V)
Grade
LP3999 Supplied as 1000
Units, Tape and Reel
LP3999 Supplied as
4500 Units, Tape and
Reel
Package
Marking
1.5 (Note 2)
STD
LP3999ILD-1.5
LP3999ILDX-1.5
L032B
1.6(Note 2)
STD
LP3999ILD-1.6
LP3999ILDX-1.6
L033B
L034B
1.8 (Note 2)
STD
LP3999ILD-1.8
LP3999ILDX-1.8
1.875(Note 2)
STD
LP3999ILD-1.875
LP3999ILDX-1.875
1.9 (Note 2)
STD
LP3999ILD-1.9
LP3999ILDX-1.9
2..0 (Note 2)
STD
LP3999ILD-2.0
LP3999ILDX-2.0
L035B
2.1 (Note 2)
STD
LP3999ILD-2.1
LP3999ILDX-2.1
2.2 (Note 2)
STD
LP3999ILD-2.2
LP3999ILDX-2.2
2.4 (Note 2)
STD
LP3999ILD-2.4
LP3999ILDX-2.4
2.5 (Note 2)
STD
LP3999ILD-2.5
LP3999ILDX-2.5
2.6 (Note 2)
STD
LP3999ILD-2.6
LP3999ILDX-2.6
2.8 (Note 2)
STD
LP3999ILD-2.8
LP3999ILDX-2.8
L038B
3.0 (Note 2)
STD
LP3999ILD-3.0
LP3999ILDX-3.0
L039B
3.3 (Note 2)
STD
LP3999ILD-3.3
LP3999ILDX-3.3
L040B
L036B
L037B
Note 1: Available in sample quantities only
Note 2: For availability contact your local sales office
5
www.national.com
LP3999
Absolute Maximum Ratings
ESD (Note 9)
(Notes 3, 4)
Human Body Model
2 kV
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Machine Model
200V
Input Voltage (VIN)
Operating Ratings (Note 3)
−0.3 to 6.5V
Output Voltage
Input Voltage (VIN)
−0.3 to (VIN + 0.3V)
to 6.5V (max)
Enable Input Voltage
2.5 to 6.0V
Enable Input Voltage
0 to 6.0V
Junction Temperature
−0.3 to 6.5V
−40 to +125˚C
150˚C
Ambient Temperature Range
(Note 7)
LLP
235˚C
Thermal Properties(Note 8)
microSMD
260˚C
Junction Temperature
Lead/Pad Temperature
(Note 5)
Storage Temperature
Junction to Ambient Thermal
Resistance
−65 to +150˚C
Continuous Power Dissipation
(Note 6)
-40 to 85˚C
θJA (LLP pkg.)
Internally limited
88˚C/W
θJA (micro SMD pkg.)
255˚C/W
Electrical Characteristics
Unless otherwise noted, VEN = 1.5, VIN = VOUT(NOM) + 1.0V, CIN = 1 µF, IOUT = 1 mA, COUT = 1 µF, cBP = 0.01 µF. Typical
values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the full temperature range for operation, −40 to +125˚C. (Note 13)
Symbol
VIN
Parameter
Conditions
Typical
Input Voltage
Limit
Min
Max
2.5
6.0
Units
V
DEVICE OUTPUT: 1.5 ≤ VOUT < 1.8V
∆VOUT
PSRR
Output Voltage Tolerance
IOUT = 1 mA
Line Regulation Error
VIN = (VOUT(NOM)+1.0V) to 6.0V,
IOUT = 1 mA
micro SMD
Load Regulation Error
IOUT = 1 mA to 150 mA
LLP
Load Regulation Error
IOUT = 1 mA to 150 mA
Power Supply Rejection Ratio
(Note 11)
−50
50
-75
75
−3.5
3.5
mV/V
10
75
µV/mA
70
125
µV/mA
f = 1 kHz, IOUT = 1 mA
58
f = 10 kHz, IOUT = 1 mA
58
mV
dB
DEVICE OUTPUT: 1.8 ≤ VOUT < 2.5V
∆VOUT
PSRR
www.national.com
Output Voltage Tolerance
IOUT = 1 mA
-50
50
−75
75
mV
microSMD
Line Regulation Error
VIN = (VOUT(NOM)+1.0V) to 6.0V,
IOUT = 1 mA
−2.5
2.5
mV/V
LLP
Line Regulation Error
VIN = (VOUT(NOM)+1.0V) to 6.0V,
IOUT = 1 mA
−3.5
3.5
mV/V
micro SMD
Load Regulation Error
IOUT = 1 mA to 150 mA
10
75
µV/mA
LLP
Load Regulation Error
IOUT = 1 mA to 150 mA
80
125
µV/mA
Power Supply Rejection Ratio
(Note 11)
f = 1 kHz, IOUT = 1 mA
60
f = 10 kHz, IOUT = 1 mA
60
6
dB
(Continued)
Unless otherwise noted, VEN = 1.5, VIN = VOUT(NOM) + 1.0V, CIN = 1 µF, IOUT = 1 mA, COUT = 1 µF, cBP = 0.01 µF. Typical
values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the full temperature range for operation, −40 to +125˚C. (Note 13)
Symbol
Parameter
Conditions
Typical
Limit
Min
Max
Units
DEVICE OUTPUT: 2.5 ≤ VOUT ≤ 3.3V
∆VOUT
PSRR
Output Voltage Tolerance
IOUT = 1 mA
-2
2
−3
3
% of
VOUT(NOM)
−0.1
0.1
%/V
0.002
%/mA
Line Regulation Error
VIN = (VOUT(NOM)+1.0V) to 6.0V,
IOUT = 1 mA
micro SMD
Load Regulation Error
IOUT = 1 mA to 150 mA
LLP
Load Regulation Error
IOUT = 1 mA to 150 mA
Dropout Voltage
IOUT = 1 mA
0.4
2
IOUT = 150 mA
60
100
f = 1 kHz, IOUT = 1 mA
60
f = 10 kHz, IOUT = 1 mA
50
Power Supply Rejection Ratio
(Note 11)
0.0004
0.003
%/mA
mV
dB
FULL VOUT RANGE
ILOAD
Load Current
(Notes 10, 11)
IQ
Quiescent Current
VEN = 1.5V, IOUT = 0 mA
85
150
VEN = 1.5V, IOUT = 150 mA
140
200
0.003
1.5
0
VEN = 0.4V
ISC
Short Circuit Current Limit
450
EN
Output Noise Voltage ((Note 11)) BW = 10 Hz to 100 kHz,
VIN = 4.2V, No Load
10
TSHUTDOWN
Thermal Shutdown
BW = 10 Hz to 100 kHz,
VIN = 4.2V, 1mA Load
30
Temperature
160
Hysteresis
20
µA
µA
mA
µVrms
˚C
ENABLE CONTROL CHARACTERISTICS
IEN
Maximum Input Current at
VEN Input
VIL
Low Input Threshold
VIH
High Input Threshold
VEN = 0.0V and VIN = 6.0V
0.001
µA
0.4
0.9
V
V
TIMING CHARACTERISTICS
TON
Turn On Time (Note 11)
To 95% Level (Note 12)
140
µs
Note 3: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device
is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical
Characteristics tables.
Note 4: All voltages are with respect to the potential at the GND pin.
Note 5: For further information on these packages please refer to the following application notes;
AN-1112 Micro SMD Package Wafer Level Chip Scale Package,
AN-1187. Leadless Leadframe Package.
Note 6: Internal Thermal shutdown circuitry protects the device from permanent damage.
Note 7: In applications where high power dissipation and/or poor thermal resistance is present, the maximum ambient temperature may have to be derated.
Maximum ambient temperature (TA(max)) is dependant on the maximum operating junction temperature (TJ(max-op)), the maximum power dissipation (PD(max)), and
the junction to ambient thermal resistance in the application (θJA). This relationship is given by :-
TA(max) = TJ(max-op) − (PD(max) x θJA)
Note 8: Junction to ambient thermal resistance is highly dependant on the application and board layout. In applications where high thermal dissipation is possible,
special care must be paid to thermal issues in the board design.
Note 9: The human body is 100 pF discharge through 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin.
Note 10: The device maintains the regulated output voltage without load.
Note 11: This electrical specification is guaranteed by design.
Note 12: Time from VEN = 0.9V to VOUT = 95% (VOUT(NOM))
7
www.national.com
LP3999
Electrical Characteristics
LP3999
Electrical Characteristics
(Continued)
Note 13: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production at TJ = 25˚C or correlated using
Statistical Quality Control methods. Operation over the temperature specification is guaranteed by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Note 14: VOUT(NOM) is the stated output voltage option for the device.
Recommended Output Capacitor
Symbol
COUT
Parameter
Output Capacitor
Conditions
Capacitance (Note 15)
Typical
1.0
ESR
Limit
Min
Max
0.75
5
Units
µF
500
mΩ
Note 15: The capacitor tolerance should be 30% or better over temperature. Recommended capacitor type is X7R however dependant on application X5R,Y5V and
Z5U can also be used.
Input Test Signals
20052006
FIGURE 1. Line Transient Response Input Test Signal
20052007
FIGURE 2. PSRR Input Test Signal
www.national.com
8
Unless otherwise specified, CIN = COUT = 1.0 µF Ceramic,
Ground Current vs Load Current (1.8V VOUT)
Output Voltage Change vs Temperature
20052011
20052010
Ground Current vs VIN @ 25˚C
Ground Current vs VIN @125˚C
20052014
20052015
Ground Current vs VIN @ -40˚C
Short Circuit Current
20052016
20052013
9
www.national.com
LP3999
Typical Performance Characteristics
VIN = VOUT + 1.0V, TA = 25˚C, Enable pin is tied to VIN.
LP3999
Typical Performance Characteristics Unless otherwise specified, CIN = COUT = 1.0 µF Ceramic, VIN
= VOUT + 1.0V, TA = 25˚C, Enable pin is tied to VIN. (Continued)
Line Transient Response (1.8V VOUT)
Line Transient Response (1.5V VOUT)
20052018
20052017
Ripple Rejection (1.8V VOUT)
Ripple Rejection (1.5V VOUT)
20052019
www.national.com
20052020
Enable Start-Up Time (VOUT = 1.8V)
Enable Start-Up Time (VOUT = 1.8V)
20052030
20052031
10
= VOUT + 1.0V, TA = 25˚C, Enable pin is tied to VIN. (Continued)
Enable Start-Up Time (VOUT = 1.5V)
Enable Start-Up Time (VOUT = 1.5V)
20052032
20052033
Load Transient Response (VOUT = 1.8V)
Load Transient Response (VOUT = 1.5V)
20052022
20052021
Output Noise Density VIN = 4.2V VOUT = 2.5V)
20052034
11
www.national.com
LP3999
Typical Performance Characteristics Unless otherwise specified, CIN = COUT = 1.0 µF Ceramic, VIN
LP3999
OUTPUT CAPACITOR
Application Hints
The LP3999 is designed specifically to work with very small
ceramic output capacitors. A ceramic capacitor (dielectric
types Z5U, Y5V or X7R) in the 1.0 [to 10 µF] range, and with
ESR between 5 mΩ to 500 mΩ, is suitable in the LP3999
application circuit.
For this device the output capacitor should be connected
between the VOUT pin and ground.
POWER DISSIPATION AND DEVICE OPERATION
The permissible power dissipation for any package is a
measure of the capability of the device to pass heat from the
power source, the junctions of the IC, to the ultimate heat
sink, the ambient environment. Thus the power dissipation is
dependent on the ambient temperature and the thermal
resistance across the various interfaces between the die and
ambient air.
As stated in (Note 7) in the electrical specification section,
the allowable power dissipation for the device in a given
package can be calculated using the equation:
It may also be possible to use tantalum or film capacitors at
the device output, VOUT, but these are not as attractive for
reasons of size and cost (see the section Capacitor Characteristics).
The output capacitor must meet the requirement for the
minimum value of capacitance and also have an ESR value
that is within the range 5 mΩ to 500 mΩ for stability.
NO-LOAD STABILITY
The LP3999 will remain stable and in regulation with no
external load. This is an important consideration in some
circuits, for example CMOS RAM keep-alive applications.
With a θJA = 255˚C/W, the device in the micro SMD package
returns a value of 392 mW with a maximum junction temperature of 125˚C.
The actual power dissipation across the device can be represented by the following equation:
PD = (VIN − VOUT) x IOUT.
This establishes the relationship between the power dissipation allowed due to thermal consideration, the voltage drop
across the device, and the continuous current capability of
the device. These two equations should be used to determine the optimum operating conditions for the device in the
application.
CAPACITOR CHARACTERISTICS
The LP3999 is designed to work with ceramic capacitors on
the output to take advantage of the benefits they offer. For
capacitance values in the range of 1 µF to 4.7 µF, ceramic
capacitors are the smallest, least expensive and have the
lowest ESR values, thus making them best for eliminating
high frequency noise. The ESR of a typical 1 µF ceramic
capacitor is in the range of 20 mΩ to 40 mΩ, which easily
meets the ESR requirement for stability for the LP3999.
The temperature performance of ceramic capacitors varies
by type. Most large value ceramic capacitors ( ≥ 2.2 µF) are
manufactured with Z5U or Y5V temperature characteristics,
which results in the capacitance dropping by more than 50%
as the temperature goes from 25˚C to 85˚C.
EXTERNAL CAPACITORS
In common with most regulators, the LP3999 requires external capacitors to ensure stable operation. The LP3999 is
specifically designed for portable applications requiring minimum board space and smallest components. These capacitors must be correctly selected for good performance.
A better choice for temperature coefficient in a ceramic
capacitor is X7R. This type of capacitor is the most stable
and holds the capacitance within ± 15% over the temperature range. Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 1 µF to 4.7 µF range.
Another important consideration is that tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum
capacitor with an ESR value within the stable range, it would
have to be larger in capacitance (which means bigger and
more costly) than a ceramic capacitor with the same ESR
value. It should also be noted that the ESR of a typical
tantalum will increase about 2:1 as the temperature goes
from 25˚C down to −40˚C, so some guard band must be
allowed.
INPUT CAPACITOR
An input capacitor is required for stability. It is recommended
that a 1.0 µF capacitor be connected between the LP3999
input pin and ground (this capacitance value may be increased without limit).
This capacitor must be located a distance of not more than
1 cm from the input pin and returned to a clean analogue
ground. Any good quality ceramic, tantalum, or film capacitor
may be used at the input.
Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must
be guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
There are no requirements for the ESR (Equivalent Series
Resistance) on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the
capacitor to ensure the capacitance will remain ≅ 1.0 µF over
the entire operating temperature range.
www.national.com
NOISE BYPASS CAPACITOR
A bypass capacitor should be connected between the CBYPASS pin and ground to significantly reduce the noise at the
regulator output. This device pin connects directly to a high
impedance node within the bandgap reference circuitry. Any
significant loading on this node will cause a change on the
regulated output voltage. For this reason, DC leakage current through this pin must be kept as low as possible for best
output voltage accuracy.
The use of a 0.01µF bypass capacitor is strongly recommended to prevent overshoot on the output during start-up.
12
micro SMD MOUNTING
The micro SMD package requires specific mounting techniques which are detailed in National Semiconductor Application Note AN-1112.
(Continued)
The types of capacitors best suited for the noise bypass
capacitor are ceramic and film. High quality ceramic capacitors with NPO or COG dielectric typically have very low
leakage. Polypropolene and polycarbonate film capacitors
are available in small surface-mount packages and typically
have extremely low leakage current.
Referring to the section Surface Mount Technology (SMT)
Assembly Considerations, it should be noted that the pad
style which must be used with the 5 pin package is NSMD
(non-solder mask defined) type.
Unlike many other LDO’s, the addition of a noise reduction
capacitor does not effect the transient response of the device.
For best results during assembly, alignment ordinals on the
PC board may be used to facilitate placement of the micro
SMD device.
ENABLE OPERATION
The LP3999 may be switched ON or OFF by a logic input at
the ENABLE pin, VEN. A high voltage at this pin will turn the
device on. When the enable pin is low, the regulator output is
off and the device typically consumes 3 nA. If the application
does not require the shutdown feature, the VEN pin should
be tied to VIN to keep the regulator output permanently on.
To ensure proper operation, the signal source used to drive
the VEN input must be able to swing above and below the
specified turn-on/off voltage thresholds listed in the Electrical
Characteristics section under VIL and VIH.
micro SMD LIGHT SENSITIVITY
Exposing the micro SMD device to direct sunlight will cause
incorrect operation of the device. Light sources such as
halogen lamps can affect electrical performance if they are
situated in proximity to the device.
Light with wavelengths in the red and infra-red part of the
spectrum have the most detrimental effect thus the fluorescent lighting used inside most buildings has very little effect
on performance. Tests carried out on a micro SMD test
board showed a negligible effect on the regulated output
voltage when brought within 1 cm of a fluorescent lamp. A
deviation of less than 0.1% from nominal output voltage was
observed.
FAST TURN ON
Fast turn-on is guaranteed by control circuitry within the
reference block allowing a very fast ramp of the output
voltage to reach the target voltage. There is no active turn-off
on this device. Refer to LP3995 for a similar device with
active turn-off.
13
www.national.com
LP3999
Application Hints
LP3999
Physical Dimensions
inches (millimeters) unless otherwise noted
micro SMD, 5 Bump, Package (TLA05)
NS Package Number TLA05ADA
The dimensions for X1, X2 and X3 are given as:
X1 = 1.006 +/− 0.03mm
X2 = 1.438 +/− 0.03mm
X3 = 0.600 +/− 0.075mm
www.national.com
14
inches (millimeters) unless otherwise noted (Continued)
LLP, 6 Lead, Package (SOT23 Land)
NS Package Number LDE06A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
LP3999 Low Noise 150mA Voltage Regulator for RF/Analog Applications
Physical Dimensions
Similar pages