TSC FRA805G 8.0 amps. glass passivated fast recovery rectifier Datasheet

FRA801G THRU FRA807G
8.0 AMPS. Glass Passivated Fast Recovery Rectifiers
Voltage Range
50 to 1000 Volts
Current
8.0 Amperes
TO-220A
Features
.185(4.70)
.175(4.44)
Low forward voltage drop
High current capability
High reliability
High surge current capability
.412(10.5)
MAX
.113(2.87)
.103(2.62)
.27(6.86)
.23(5.84)
.594(15.1)
.587(14.9)
Mechanical Data
.055(1.40)
.045(1.14)
DIA
.154(3.91)
.148(3.74)
PIN1
2
.16(4.06)
.14(3.56)
Cases: Molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: Leads solderable per
MIL-STD-202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260℃/10 seconds .16”,(4.06mm) from
case.
Mounting position: Any
Weight: 2.24 grams
.56(14.22)
.53(13.46)
.11(2.79)
.10(2.54)
.037(0.94)
.027(0.68)
.025(0.64)
.014(0.35)
.205(5.20)
.195(4.95)
PIN 1
PIN 2
CASE
Case Positive
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol FRA FRA FRA
Type Number
FRA FRA FRA FRA
801G 802G 803G 804G 805G 806G 807G
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
@TC = 55℃
Peak Forward Surge Current, 8.3 ms Single Half
Sine-wave Superimposed on Rated Load (JEDEC
method )
VRRM
VRMS
VDC
50
35
50
100
70
100
200
140
200
400
280
400
600
420
600
800
560
800
1000
700
1000
Units
V
V
V
I(AV)
8.0
A
IFSM
150
A
Maximum Instantaneous Forward Voltage @ 8.0A
VF
Maximum DC Reverse Current @ TC=25℃
at Rated DC Blocking Voltage @ TC=125℃
IR
1.3
5.0
100
V
uA
uA
nS
pF
℃/W
℃
Maximum Reverse Recovery Time ( Note 2 )
Typical Junction Capacitance ( Note 1 ) TJ=25℃
Typical Thermal Resistance (Note 3)
Operating and Storage Temperature Range
Trr
Cj
RθJC
TJ ,TSTG
150
250
60
3.0
-65 to +150
Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4..0 Volts D.C.
2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
3. Thermal Resistance from Junction to Case, with Heatsink size 2” x 3” x 0.25” Al-Plate
- 452 -
500
RATINGS AND CHARACTERISTIC CURVES (FRA801G THRU FRA807G)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
10W
NONINDUCTIVE
50W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
0
-0.25A
(+)
-1.0A
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
1cm
FIG.5- TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
400
10
200
6
4
2
0
0
50
100
150
o
PEAK FORWARD SURGE CURRENT. (A)
CASE TEMPERATURE. ( C)
150
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
100
40
Tj=25oC
Pulse Width=300 s
1% Duty Cycle
20
10
4
2
1
0.4
0.2
125
0.1
0.6
TJ=125 0C
100
0.8
1.0
1.2
1.4
1.6
1.8
2.0
INSTANTANEOUS FORWARD VOLTAGE. (V)
8.3ms Single Half Sine Wave
JEDEC Method
75
FIG.6- TYPICAL REVERSE CHARACTERISTICS
50
100
25
0
1
2
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE
120
CAPACITANCE.(pF)
INSTANTANEOUS FORWARD CURRENT. (A)
8
100
80
60
40
Tj=25 0C
f=1.0MHz
Vsig=50mVp-p
20
40
INSTANTANEOUS REVERSE CURRENT. ( A)
AVERAGE FORWARD CURRENT. (A)
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
SET TIME BASE FOR
5/ 10ns/ cm
Tj=125 0C
10
2
1
0.4
0.1
0.5
1
5
10
50
100
500 1000
REVERSE VOLTAGE. (V)
- 453 -
Tj=25 0C
0.2
0.1
0
Tj=75 0C
4
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
Similar pages