Abracon ABPX1101-XXXMC Advanced programmable clock Datasheet

ABPX1101
Advanced Programmable Clock
FEATURES
•
•
•
XIN/FIN
1
GND
2
CLK0
3
CLK1
4
8
XOUT
7
CLK2,OE,PDB,FSEL
6
NC
5
VDD
SOP-8
MSOP-8
CLK0
1
GND
2
XIN/FIN
3
ABPX1101
•
•
Advanced programmable PLL design
Very low Jitter and Phase Noise (30-70ps Pk-Pk typical)
Up to 3 programmable outputs
Two registers banks for 2-time programming.
Output frequency up to 200MHz CMOS.
Accepts Crystal or reference clock inputs
o Fundamental crystal: 10MHz-30MHz
o 3 RD overtone crystal: Up to 75MHz
o Reference input: Up to 200MHz
Accepts <1.0V reference signal input voltage
One programmable I/O pin can be configured as
Programmable clock, or Frequency Selection input,
or output Enable (OE) or Power Down (PDB) input.
Single 2.5V or 3.3V ± 10% power supply
Operating temperature range from -40°C to 85°C
Available in 8-pin MSOP/SOIC, and 6-pin SOT
ABPX1101
•
•
•
•
•
•
PIN CONFIGURATION
6
VDD
5
CLK2,OE,PDB,FSEL
4
XOUT
SOT-23
DESCRIPTION
The ABPX1101 is a low-cost general purpose frequency synthesizer and a member of Abracons’ Advanced
Programmable Clock family. Abracon’s ABPX1101 product family offers the versatility of using a single Crystal or
Reference Clock input and producing up to three different system clocks. They can generate any output
frequency up to 200 MHz from fundamental crystal input between 10 MHz - 30 MHz, or a 3rd overtone crystal of
up to 75Mhz, or a Reference clock input of up to 200 MHz. Cascading of the ICs to produce additional clock
frequencies is also supported.
BLOCK DIAGRAM
XIN/FIN
Xtal
OSC
XOUT
FRef
R-counter
(8-bit)
Phase
Detector
Charge
Pump
Loop
Filter
M -counter
(10-bit)
FVCO = F Ref. * (2 * M /R)
OE
PDB
CLoad
Programming
Logic
FSEL
VCO
P-counter
(5-bit)
Fout = FVCO / (2 * P)
Selectable
/1,/2,/4,/8
CLOCK[0:2]
Selectable
/1,/2
Programmable Function
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 1
ABPX1101
Advanced Programmable Clock
KEY PROGRAMMING PARAMETERS
CLK[ 0:2 ]
Output Frequency
Output Drive
Strength
Fout = FIN * M / (R * P)
where M=10 bit
R= 8 bit
P= 5 bit
1. CLK[0:2]= Fout/[1,2,4,8]
2. CLK[0:2]= FIN or FIN/2
Std: 10mA (default)
High: 24mA
Crystal
Load
# of
Register
Banks
Programmable
Input/Output
+/- 200ppm One output pin can
tuning.
be configured as
1. CLK2 - output
2. FSEL - input
3. OE - input
4. PDB - input
2
ChargePump
Current
4 levels of
pump
current
settings
PIN DESCRIPTION
Name
Pin #
MSOP-8
SOT-23
SOIC-8
Type
Description
XIN/FIN
1
3
I
Crystal or Reference input pin
GND
2
2
P
GND connection
CLK[0:1]
3,4
1
O
Programmable Clock Output
VDD
5
6
P
VDD connection (2.25~3.63V)
NC
6
No Connect
This programmable I/O pin can be configured as a
programmable clock output (CLK2), or Output Enable
(OE) input, or Power Down input (PDB), or Frequency
Selection (FSEL) input pin. This pin has an internal
60KΩ pull up resistor.
CLK2, OE, PDB, FSEL
7
5
B
State
0
1
(default)
XOUT
8
4
O
OE
PDB
FSEL
Tristate
Power
Down
Mode
Select
Bank ’0’
ROM
Normal
mode
Select
Bank ‘1’
ROM
CLK[0:1]
Normal
mode
Crystal output pin
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 2
ABPX1101
Advanced Programmable Clock
ELECTRICAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
PARAMETERS
SYMBOL
MIN.
MAX.
UNITS
V DD
- 0.5
4.6
V
Input Voltage Range
VI
- 0.5
V DD + 0.5
V
Output Voltage Range
VO
- 0.5
V DD + 0.5
V
260
°C
Supply Voltage Range
Soldering Temperature (Green package)
10
Data Retention @ 85°C
Storage Temperature
TS
Ambient Operating Temperature
Year
-65
150
°C
-40
85
°C
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device
and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above
the operational limits noted in this specification is not implied.
AC SPECIFICATIONS
PARAMETERS
Crystal Input Frequency(XIN)
CONDITIONS
Fundamental Crystal
MIN.
TYP.
10
3 rd Overtone Crystal
Input (FIN) Frequency
Input (FIN) Signal Amplitude
Internally AC coupled
Settling Time
At power-up (after VDD increases over
1.62V)
Output Rise Time
Output Fall Time
0.9
MAX.
UNITS
30
MHz
75
MHz
200
MHz
VDD
Vpp
10
ms
15pF Load, 10/90%VDD, Standard drive
2.5
3.5
ns
15pF Load, 10/90%VDD, High drive
1.0
1.5
ns
15pF Load, 90/10%VDD, Standard drive
2.5
3.5
ns
15pF Load, 90/10%VDD, High drive
1.0
1.5
ns
50
55
%
500
ps
Duty Cycle
At VDD/2
Max. output skew between
same frequency clocks
Equal loading (15 pF). Equal frequency
& drive strength
Period Jitter, peak-to-peak*
(measured from 10,000
samples)
With capacitive decoupling between VDD
and GND. Operating only one output.
45
70
ps
* Note: Jitter performance depends on the programming parameters.
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 3
ABPX1101
Advanced Programmable Clock
DC SPECIFICATIONS
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
At 10MHz, load=15pF
MAX.
UNITS
15
mA
5
µA
3.63
V
0.4
V
Supply Current, Dynamic, with
Loaded Outputs
I DD
Operating Voltage
V DD
Output Low Voltage
V OL
Output High Voltage
V OH
Output Current, Standard drive
I OSD
V OL = 0.4V, V OH = 2.4V
10.7
mA
Output Current, High drive
I OHD
V OL = 0.4V, V OH = 2.4V
24
mA
(PDB=1)
PDB=0
Short-circuit Current
2.25
I OL = +4mA
Standard drive
I OH = -4mA
V DD –
0.4
Standard drive
IS
V
±50
mA
CRYSTAL SPECIFICATIONS
PARAMETERS
SYMBOL
MIN.
Fundamental Crystal Resonator Frequency
F XIN
10
3rd Overtone Crystal Resonator Frequency
F XIN
Crystal Loading Rating
(The IC can be programmed for any value in this range.)
C L (xtal)
TYP.
5
Maximum Sustainable Drive Level
Operating Drive Level
Crystal Shunt Capacitance
MAX.
UNITS
30
MHz
75
MHz
20
pF
500
µW
µW
100
C0
6
pF
Effective Series Resistance, Fundamental, 10-30MHz
ESR
30
Ω
Effective Series Resistance, 3 rd Overtone, 30-50MHz
[CO< 4pF, C L =(5pF)/(8pF)]
ESR
100/70
Ω
Effective Series Resistance, 3 rd Overtone, 50-65MHz,
[CO< 4pF, C L =5pF(5pF)/(8pF)]
ESR
60/40
Ω
Effective Series Resistance, 3 rd Overtone, 65-75MHz
[CO< 4pF, C L =(5pF)/(8pF)]
ESR
45/30
Ω
Note: A detailed crystal specification document is also available for this part
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 4
ABPX1101
Advanced Programmable Clock
PACKAGE DRAWINGS (GREEN PACKAGE COMPLIANT)
MSOP 8L
Symbol
A
A1
A2
B
C
D
E
H
L
e
Dimension in MM
Min.
Max.
--1.10
0.05
0.15
0.81
0.91
0.25
0.40
0.13
0.23
2.90
3.10
2.90
3.10
4.90 BSC
0.445
0.648
0.65 BSC
E
H
D
A2 A
A1
C
L
b
e
SOIC 8L
Symbol
A
A1
A2
B
C
D
E
H
L
e
Dimension in MM
Min.
Max.
1.35
1.75
0.10
0.25
1.25
1.50
0.33
0.53
0.19
0.27
4.80
5.00
3.80
4.00
5.80
6.20
0.40
0.89
1.27 BSC
E
H
D
A2 A
A1
C
L
b
e
SOT-23 6 L
Symbol
A
A1
A2
B
C
D
E
H
L
e
Dimension in MM
Min.
Max.
1.05
1.35
0.05
0.15
1.00
1.20
0.30
0.50
0.08
0.20
2.80
3.00
1.50
1.70
2.60
3.0
0.35
0.55
0.95 BSC
E
H
D
A2 A
A1
C
e
b
L
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 5
ABPX1101
Advanced Programmable Clock
ORDERING INFORMATION
For part ordering, please contact our Sales Department:
30332 Esperanza., Rancho Santa Margarita, Ca 92688
Ph: 949-546-8000 Fax: 949-546-8001
PART NUMBER
The order number for this device is a combination of the following:
Device number, Package type and Operating temperature range
ABPX1101-XXX
X X-X
PART NUMBER
3 DIGIT ID Code *
NONE= TUBE
T=TAPE and REEL
PACKAGE TYPE
S=SOIC
M=MSOP
T=SOT
TEMPERATURE
C=COMMERCIAL
I = INDUSTRIAL
* Abracon will assign a unique 3-digit ID code for each approved programmed part number.
* Abracon offers Green Package Only for this product family.
Part / Order Number*
Marking
Package Option
ABPX1101-XXXSC
A1XXX
8-Pin SOIC (Tube)
ABPX1101-XXXSC-T
A1XXX
8-Pin SOIC (Tape and Reel)
ABPX1101-XXXMC
A1XXX
8-Pin MSOP (Tube)
ABPX1101-XXXMC-T
A1XXX
8-Pin MSOP (Tape and Reel)
ABPX1101-XXXTC-T
A1XXX
6-Pin SOT-23 (Tape and Reel)
* Ordering will include Programming ID number that will be supplied at the time
the samples are provided.
Abracon Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information
furnished by Abracon is believed to be accurate and reliable. However, Abracon makes no guarantee or warranty concerning the accuracy of said
information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product.
LIFE SUPPORT POLICY: Abracon’s products are not authorized for use as critical components in life support devices or systems without the express
written approval of the President of Abracon Corporation.
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 6
Similar pages