ETC2 CPMC-TNC-13 Tnc straight crimp type plug - solder or crimp contact - 3 piece Datasheet

INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
TNC Straight Crimp Type Plug Solder or Crimp Contact - 3 Piece
PART NUMBER CABLE TYPE
CPMC-TNC-13 RG-142, 223, 400, 55
“A”
.520 (13.20)
“B”
.595 (15.11)
CONTACT I.D.
.044 (1.12)
BODY I.D.
.126 (3.20)
FERRULE I.D.
.220 (5.59)
1. Identify connector parts. (3 piece parts - except bulkheads)
2. Strip cable to dimensions shown. Do not nick braid or center
conductor. Tin center conductor if contact will be solder attached.
Do not tin center conductor if contact is to be crimp attached. A
wire stripper of correct size is recommended for this step. Slide
heat shrink (as applicable) and crimp sleeve onto jacket of cable.
3. Assemble contact onto cable as shown.
Solder Attachment: Solder contact to center conductor through
hole using a minimum amount of solder for a good joint.
Crimp Attachment (where applicable): Crimp contact to center conductor using recommended crimp hex.
4. Flare braid and slide body assembly over contact and under braid.
Then seat body assembly firmly onto contact. The cable may
have to be held in a clamping fixture. Arrange braid uniformly
around crimp stem. Slide crimp sleeve forward and crimp using
recommended crimp hex. Slide heat shrink forward and shrink
(as applicable).
Strip Dimensions
Part Number
Cable
CPMC-TNC-13
RG-55, 142
“A”
.315 (8.00)
“B”
.118 (3.00)
Crimp
Contact
Recommended
“C”
Sleeve Hex
Crimp Hex
Crimp Tool
.157 (4.00)
.213 (5.41)
.060 (1.52)
24-304P
Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • 1-800-243-8814 • Fax: 507-833-6287 • www.cambridgeproducts.com
TNC Connectors
Specifications
INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
The TNC connector is a threaded version of the BNC mating interface. All contacts
are captivated for ruggedness. The TNC is a commercial quality connector that
provides additional retention for shock and vibration applications. The TNC connector intermates with all standard 50 Ohm TNC connectors.
Specifications*
Electrical Characteristics
Impedance: 50 Ohm nominal (except where noted)
Frequency range: 0-11 GHz
Working voltage: 500 volts RMS at sea level
Dielectric withstanding voltage: 1500 volts RMS at sea level
Corona level: 375 volts minimum at 70,000 feet
Contact resistance: Outer - 0.2 milliohms maximum
Center - 2.1 milliohms maximum
Insulation resistance: 5000 megohms minimum
Environmental Characteristics
Recommended temperature range: -55OC to +85OC
Moisture Resistance: MIL-STD-202
Mechanical Characteristics
Durability: 500 cycles
Cable retention: 20 lbs., RG-58 C/U cable
Materials
Body and coupling nut: Zinc or brass
Contact: Beryllium copper, phosphor bronze or brass
Crimp Sleeve: Brass
Insulator: Teflon®, TPX or Delrin®
Hardware: Brass
Plating: Body - Nickel
Crimp sleeve - Nickel
Hardware - Nickel
Contact - Gold
* These values are typical and may not apply to all connectors.
Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • 1-800-243-8814 • Fax: 507-833-6287 • www.cambridgeproducts.com
Similar pages