AD ADL5391ACPZ-WP Dc to 2.0 ghz multiplier Datasheet

DC to 2.0 GHz
Multiplier
ADL5391
Ultrafast symmetric multiplier
Function: VW = α × (VX × VY)/1 V + VZ
Unique design ensures absolute XY-symmetry
Identical X and Y amplitude/timing responses
Adjustable gain scaling, α
DC-coupled throughout, 3 dB bandwidth of 2 GHz
Fully differential inputs, may be used single ended
Low noise, high linearity
Accurate, temperature stable gain scaling
Single-supply operation (4.5 V to 5.5 V @ 130 mA)
Low current power-down mode
16-lead LFCSP
FUNCTIONAL BLOCK DIAGRAM
YMNS YPLS
GADJ
XPLS
ZMNS
XMNS
ZPLS
WPLS
ENBL
WMNS
ADL5391
VMID
W = αXY/1V+Z
COMM VPOS
06059-001
FEATURES
Figure 1.
APPLICATIONS
Wideband multiplication and summing
High frequency analog modulation
Adaptive antennas (diversity/phased array)
Square-law detectors and true rms detectors
Accurate polynomial function synthesis
DC capable VGA with very fast control
GENERAL DESCRIPTION
The ADL5391 draws on three decades of experience in
advanced analog multiplier products. It provides the same
general mathematical function that has been field proven to
provide an exceptional degree of versatility in function synthesis.
VW = α × (VX × VY)/ 1 V + VZ
The most significant advance in the ADL5391 is the use of a
new multiplier core architecture, which differs markedly from
the conventional form that has been in use since 1970. The
conventional structure that employs a current mode, translinear
core is fundamentally asymmetric with respect to the X and Y
inputs, leading to relative amplitude and timing misalignments
that are problematic at high frequencies. The new multiplier
core eliminates these misalignments by offering symmetric
signal paths for both X and Y inputs. The Z input allows a signal
to be added directly to the output. This can be used to cancel a
carrier or to apply a static offset voltage.
The fully differential X, Y, and Z input interfaces are operational
over a ±2 V range, and they can be used in single-ended fashion.
The user can apply a common mode at these inputs to vary
from the internally set VPOS/2 down to ground. If these inputs
are ac-coupled, their nominal voltage will be VPOS/2. These input
interfaces each present a differential 500 Ω input impedance up to
approximately 700 MHz, decreasing to 50 Ω at 2 GHz. The gain
scaling input, GADJ, can be used for fine adjustment of the gain
scaling constant (α) about unity.
The differential output can swing ±2 V about the VPOS/2
common-mode and can be taken in a single-ended fashion as
well. The output common mode is designed to interface directly
to the inputs of another ADL5391. Light dc loads can be ground
referenced; however, ac-coupling of the outputs is recommended
for heavy loads.
The ENBL pin allows the ADL5391 to be disabled quickly to a
standby mode. It operates off supply voltages from 4.5 V to
5.5 V while consuming approximately 130 mA.
The ADL5391 is fabricated on Analog Devices proprietary, high
performance, 65 GHz, SOI complementary, SiGe bipolar IC
process. It is available in a 16-lead, Pb-free, LFCSP and operates
over a −40°C to +85°C temperature range. Evaluation boards
are available.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADL5391
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Applications....................................................................................... 1
General Description....................................................................... 10
Functional Block Diagram .............................................................. 1
Basic Theory ............................................................................... 10
General Description ......................................................................... 1
Basic Connections...................................................................... 10
Revision History ............................................................................... 2
Evaluation Board ............................................................................ 13
Specifications..................................................................................... 3
Outline Dimensions ....................................................................... 15
Absolute Maximum Ratings............................................................ 5
Ordering Guide .......................................................................... 15
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
REVISION HISTORY
7/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADL5391
SPECIFICATIONS
VPOS = 5 V, TA = 25°C, ZL = 50 Ω differential, ZPLS = ZMNS = open, GADJ = open, unless otherwise noted. Transfer function: W =
XY/1 V + Z, common mode internally set to 2.5 V nominal.
Table 1.
Parameter
MULTIPLICAND INPUTS (X, Y)
Differential Voltage Range
Common-Mode Range
Input Offset Voltage
vs. Temperature
Differential Input Impedance
Fundamental Feedthrough, X or Y
Gain
DC Linearity
Scale Factor
CMRR
SUMMING INPUT (Z)
Differential Voltage Range
Common-Mode Range
Gain
Differential Input Impedance
OUTPUTS (W)
Differential Voltage Range
Common-Mode Output
Output Noise Floor
Output Noise Voltage Spectral Density
Output Offset Voltage
vs. Temperature
Differential Output Impedance
DYNAMIC CHARACTERISTICS
Frequency Range
Slew Rate
Settling Time
Second Harmonic Distortion
Third Harmonic Distortion
Conditions
XPLS, XMNS, YPLS, YMNS
Differential, common mode = 2.5 V
For full differential range
DC
−40°C to +85°C
f = dc
f = 2 GHz
f = 50 MHz, X (Y) = 0 V, Y (X) = 0 dBm, relative to
condition where X (Y) = 1 V
f = 1 GHz
X = 50 MHz and 0 dBm, Y = 1 V
X = 1 GHz and 0 dBm, Y = 1 V
X to output, Y = 1 V
X=Y=1V
±1 V p-p, Y = 1 V, f = 50 MHz
ZPLS, ZMNS
Common mode from 2.5 V down to COMM
For full differential range
From Z to W, f ≤ 10 MHz, 0 dBm, X = Y = 1 V
f = dc
f = 2 GHz
WPLS, WMNS
No external common mode
Min
Unit
20
±20
500
150
−42
V p-p
V
mV
mV
Ω
Ω
dB
−35
0.5
−1.33
1
1
42.1
dB
dB
dB
% FS
V/V
dB
2.5
2
0.1
500
150
V p-p
V
dB
Ω
Ω
±2
VPOS − 2.5
V
V
−133
−133
dBm/Hz
dBm/Hz
−138
−138
26.7
19
±19
0
75
500
dBm/Hz
dBm/Hz
nV/√Hz
mV
mV
Ω
Ω
Ω
0
f = dc
f = 200 MHz
f = 2 GHz
Rev. 0 | Page 3 of 16
Max
2
0
X = Y = 1 V dc
f = 1 MHz
f = 1 GHz
X=Y=0
f = 1 MHz
f = 1 GHz
X = Y = 0, f = 1 MHz
Z = 0 V differential
X, Y, Z to W
W from −2.0 V to +2.0 V, 150 Ω
X stepped from −1 V to +1 V, Z = 0 V, 150 Ω
X (Y) = 0 dBm, Y (X) = 1 V, fund = 10 MHz
Fund = 200 MHz
X (Y) = 0 dBm, Y (X) = 1 V, fund = 10 MHz
Fund = 200 MHz
Typ
2.5
0
2
8800
2.1
−60
−51
−61.5
−51.6
GHz
V/μs
ns
dBc
dBc
dBc
dBc
ADL5391
Parameter
OIP3
OIP2
Output 1 dB Compression Point
Group Delay
Differential Gain Error, X/Y
Differential Phase Error, X/Y
GAIN TRIMMING (α)
Nominal Bias
Input Range
Gain Adjust Range
REFERENCE VOLTAGE
Source Current
POWER AND ENABLE
Supply Voltage Range
Total Supply Current
Disable Current
Disable Threshold
Enable Response Time
Disable Response Time
Conditions
Two-tone IP3 test; X (Y) = 100 mV p-p/tone
(−10 dBm into 50 Ω), Y (X) = 1
f1= 49 MHz, f = 50 MHz
f1 = 999 MHz, f2 = 1 GHz
f1 = 49 MHz, f = 50 MHz
f1 = 999 MHz, f2 = 1 GHz
X (Y) to W, Y (X) = 1 V, 50 MHz
1 GHz
200 MHz
1 GHz
f = 3.58 MHz
f = 3.58 MHz
GADJ
Unconnected
Min
Typ
26.5
14
45.5
28
15.1
13.2
0.5
0.7
2.7
0.23
Input 0 V to 2 V
VMID
Common-mode for X, Y, Z = 2.5 V
VPOS, COMM, ENBL
2
9.5
VPOS/2
50
4.5
Rev. 0 | Page 4 of 16
Unit
dBm
dBm
dBm
dBm
dBm
dBm
ns
ns
%
Degrees
1.12
0
Common-mode for X, Y, Z = 2.5 V
ENBL = 0 V
High to Low
Delay following high-to-low transition until device
meets full specifications
Delay following low-to-high transition until device
produces full attenuation
Max
5.5
V
V
dB
V
mA
135
7.5
1.5
150
V
mA
mA
V
ns
50
ns
ADL5391
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltage VPOS
ENBL
XPLS, XMNS, YPLS, YMNS, ZPLS, ZMNS
GADJ
Internal Power Dissipation
θJA (With Pad Soldered to Board)
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering 60 sec)
Rating
5.5 V
5.5 V
VPOS
VPOS
800 mW
73°C/W
150°C
−40°C to +85°C
−65°C to +150°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 16
ADL5391
13 XPLS
ADL5391
VPOS 4
12 YMNS
11 YPLS
10 ZPLS
GADJ 8
COMM 7
WPLS 5
WMNS 6
9 ZMNS
06059-002
VPOS 3
14 XMNS
16 VMID
PIN 1
INDICATOR
COMM 1
VPOS 2
15 ENBL
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1, 7
2 to 4
5, 6
8
9, 10
11, 12
13, 14
15
16
Mnemonic
COMM
VPOS
WPLS, WMNS
GADJ
ZMNS, ZPLS
YPLS, YMNS
XPLS, XMNS
ENBL
VMID
Description
Device Common. Connect via lowest possible impedance to external circuit common.
Positive Supply Voltage. 4.5 V to 5.5 V.
Differential Outputs.
Denominator Scaling Input.
Differential Intercept Inputs. Must be ac-coupled. Differential impedance 50 Ω nominal.
Differential X-Multiplicand Inputs.
Differential Y-Multiplicand Inputs.
Chip Enable. High to enable.
VPOS/2 Reference Output. Connect decoupling capacitor to circuit common.
Rev. 0 | Page 6 of 16
ADL5391
TYPICAL PERFORMANCE CHARACTERISTICS
GADJ = open.
14
Y = –2
Y = –1
Y=0
Y = +1
Y = +2
2.5
2.0
1.5
8
4
0.5
GAIN (dB)
0
–0.5
50
2
–0
0
–2
–50
–4
–6
–1.5
–100
–8
–2.0
–10
–2.5
–150
–12
0
0.5
1.0
1.5
2.0
2.5
XDIFF (VDC)
–14
–200
06059-010
–0.5
FREQUENCY (MHz)
Figure 3. Full Range DC Cross Plots
Figure 6. Gain and Phase vs. Frequency of X Swept and Y = 1 V, Z = 0 V,
PIN = 0 dBm
0
–0
–1
–50
–2
–100
–3
–150
–4
–200
–0.05
–0.20
–0.20
–0.15
–0.10
–0.05
0
0.05
0.10
0.15
0.20
XDIFF (VDC)
1
–0.15
06059-008
Y = –2
Y = –1
Y=0
Y = +1
Y = +2
–0.10
06059-011
0
1300
50
1200
1
1100
0.05
990
100
880
2
700
0.10
660
150
550
3
440
0.15
330
200
220
4
GAIN (dB)
0.20
PHASE (Degrees)
–1.0
5
100
195
290
385
480
575
670
765
860
955
1050
1150
1240
1340
1430
1530
1620
1720
1810
1910
2000
–1.5
06059-007
–2.0
110
WDIFF (VDC)
100
6
–1.0
WDIFF (VDC)
150
10
1.0
–3.0
–2.5
200
12
PHASE (Degrees)
3.0
FREQUENCY (MHz)
Figure 7. Gain and Phase vs. Frequency of Z Inputs, X = 0 V, Y = 0 V,
PIN = 0 dBm
Figure 4. Magnified DC Cross Plots
2.0
2.5
X ± INPUT = 1.0V p-p, @ 200MHz
Y ± INPUT = 1.0V DC DIFFERENTIAL
1.5
2.0
WOUTPUT (V)
1.5
1.0
0.5
0
–0.5
–1.0
0.5
0
–1.0
–0.5
0
0.5
1.0
GADJ (VDC)
1.5
2.0
Figure 5. Gain vs. GADJ (X = Y = 1)
–2.0
24.5
25.5
26.5
27.5
28.5
29.5
30.5
31.5
TIME (ns)
Figure 8. Large Signal Pulse Response
Rev. 0 | Page 7 of 16
32.5
33.5
06059-013
–1.5
06059-009
GAIN (V/V)
1.0
ADL5391
0.20
30
X ± INPUT = ±100mV p-p, @ 200MHz
Y ± INPUT = 1.0V DC DIFFERENTIAL
0.15
25
20
0.05
OIP3 (dBm)
WOUTPUT (V)
0.10
0
–0.05
Y=1
15
Y = 0.5
10
–0.10
25.5
26.5
27.5
28.5
29.5
30.5
31.5
0
06059-014
–0.20
24.5
32.5
TIME (ns)
0
500
1000
1500
2000
FREQUENCY (MHz)
Figure 9. Small Signal Pulse Response
06059-016
5
–0.15
Figure 12. OIP3 vs. Frequency
Pin 0 dBm, Y = 1 V dc, 0.5 V dc
0.05
0.04
0.03
+85°C, X = +1
+85°C, X = –1
–40°C, X = –1
–40°C, X = +1
+25°C, X = –1
+25°C, X = +1
WDIFF (VDC)
0.02
10MHz
10dBm/DIV
10dBm/DIV
200MHz
400MHz
0.01
0
–0.01
600MHz
–0.02
–0.03
30MHz
06059-094
–0.05
–0.05 –0.04 –0.03 –0.02 –0.01
0
0.01
0.02
0.03
0.04
0.05
YDIFF (VDC)
Figure 10. Harmonic Distortion at 10 MHz and 200 MHz;
0 dBm Input to X (Y) Channels
06059-021
–0.04
20MHz
Figure 13. Z (W) Offset Over Temperature
28
45
X = 0V, Y = 1V
26
40
X = Y = 1V
22
SND (nV/ Hz)
35
20
18
16
X = Y = 0V
30
25
14
20
10
–40
–15
10
35
60
TEMPERATURE (°C)
85
15
200
400
600
800
1000 1200 1400 1600 1800 2000
FREQUENCY (MHz)
Figure 11. X ( Y) Offset Drift vs. Temperature
Figure 14. Noise vs. Frequency
Rev. 0 | Page 8 of 16
06059-019
12
06059-015
AVERAGE VOFFSET (VDC)
24
ADL5391
S22 SE
S11 SE
1.00UFS
1.00UFS
S11 DIFF
S22 DIFF
3001.000
0.654 U
0.594 U
0.531 U
–36.340 DEG
–92.533 DEG
–94.448 DEG
201.000
2001.000
0.800 U
0.564 U
–17.218 DEG
–58.167 DEG
06059-017
201.000
1001.000
1901.000
1.000
Figure 15. Input S11
3001.000
201.000
1001.000
1901.000
0.947 U
0.569 U
0.597 U
+170.736 DEG
+58.257 DEG
–69.673 DEG
201.000
2001.000
0.905 U
0.663 U
+157.308 DEG
–39.468 DEG
Figure 16. Output S22
Rev. 0 | Page 9 of 16
06059-018
1.000
ADL5391
GENERAL DESCRIPTION
BASIC THEORY
The multiplication of two analog variables is a fundamental
signal processing function that has been around for decades.
By convention, the desired transfer function is given by
W = αXY/U + Z
(1)
where:
X and Y are the multiplicands.
U is the multiplier scaling factor.
α is the multiplier gain.
W is the product output.
Z is a summing input.
All the variables and the scaling factor have the dimension of volts.
In the past, analog multipliers, such as the AD835, were
implemented almost exclusively with a Gilbert Cell topology
or a close derivative. The inherently asymmetric signal paths
for X and Y inevitably create amplitude and delay imbalances
between X and Y. In the ADL5391, the novel multiplier core
provides absolute symmetry between X and Y, minimizing
scaling and phasing differences inherent in the Gilbert Cell.
All input ports, X, Y, and Z, are differential and internally
biased to midsupply, VPOS/2. The differential input impedance is
500 Ω up to 100 MHz, rolling off to 50 Ω at 2 GHz. All inputs
can be driven in single-ended fashion and can be ac-coupled. In
dc-coupled operation, the inputs can be biased to a common
mode that is lower than VPOS/2. The bias current flowing out of
the input pins to accommodate the lower common mode is
subtracted from the 50 mA total available from the internal
reference VPOS/2 at the VREF pin. Each input pin presents an
equivalent 250 Ω dc resistance to VPOS/2. If all six input pins sit
1 V below VPOS/2, a total of 6 × 1 V/250 Ω = 24 mA must flow
internally from VREF to the input pins.
Calibration
The simplified block diagram of the ADL5391 shows a main
multiplier cell that receives inputs X and Y and a second
multiplier cell in the feedback path around an integrating
buffer. The inputs to this feedback multiplier are the difference
of the output signal and the summing input, W − Z, and the
internal scaling reference, U. At dc, the integrating buffer
ensures that the output of both multipliers is exactly 0, therefore
(W − Z)xU = XY, or W = XY/U + Z
The small-signal bandwidth from the inputs X, Y, and Z to
the output W is a single-pole response. The pole is inversely
proportional to α. For α = 1 (GADJ floating), the bandwidth is
about 2 GHz; for α > 1, the bandwidth is reduced; and for α < 1,
the bandwidth is increased.
(2)
By using a feedback multiplier that is identical to the main
multiplier, the scaling is traced back solely to U, which is
an accurate reference generated on-chip. As is apparent in
Equation 2, noise, drift, or distortion that is common to both
multipliers is rejected to first-order because the feedback
multiplier essentially compensates the impairments generated
in the main multiplier.
The scaling factor, U, is fixed by design to 1.12 V. However, the
multiplier gain, α, can be adjusted by driving the GADJ pin with
a voltage ranging from 0 V to 2 V. If left floating, then α = 1 or
0 dB, and the overall scaling is simply U = 1 V. For VGADJ = 0 V,
the gain is lowered by approximately 4 dB; for VGADJ = 2 V,
the gain is raised by approximately 6 dB. Figure 5 shows the
relationship between α(V/V) and VGADJ.
The dc offset of the ADL5391 is approximately 20 mV but
changes over temperature and has variation from part to part
(see Figure 4). It is generally not of concern unless the ADL5391
is operated down to dc (close to the point X = 0 V or Y = 0 V),
where 0 V is expected on the output (W = 0 V). For example,
when the ADL5391 is used as a VGA and a large amount of
attenuation is needed, the maximum attenuation is determined
by the input dc offset.
Applying the proper voltage on the Z input removes the W
offset. Calibration can be accomplished by making the appropriate
cross plots and adjusting the Z input to remove the offset.
Additionally, gain scaling can be adjusted by applying a dc
voltage to the GADJ pin, as shown in Figure 5.
BASIC CONNECTIONS
Multiplier Connections
The best ADL5391 performance is achieved when the X, Y, and
Z inputs and W output are driven differentially; however, they
can be driven single-ended. Single-ended-to-differential
transformations (or differential-to-single-ended transformations)
can be done using a balun or active components, such as the
AD8313, the AD8132 (both with operation down to dc), or the
AD8352 (for higher drive capability). If using the ADL5391
single-ended without ac coupling capacitors, the reference
voltage of 2.5 V needs to be taken into account. Voltages above
2.5 V are positive voltages and voltages below 2.5 V are negative
voltages. Care needs to be taken not to load the ADL5391 too
heavily, the maximum reference current available is 50 mA.
Rev. 0 | Page 10 of 16
ADL5391
The input and output impedance’s of the ADL5391 change over
frequency, making it difficult to match over a broad frequency
range (see Figure 15 and Figure 16). The evaluation board is
matched for lower frequency operation, and the impedance
change at higher frequencies causes the change in gain seen in
Figure 6. If desired, the user of the ADL5391 can design a
matching network to fit their application.
Wideband Voltage-Controlled Amplifier/Amplitude
Modulator
Most of the data for the ADL5391 was collected by using it as a
fast reacting analog VGA. Either X or Y inputs can be used for
the RF input (and the other as the very fast analog control),
because either input can be used from dc to 2 GHz. There is a
linear relationship between the analog control and the output of
the multiplier in the VGA mode. Figure 6 and Figure 7 show the
dynamic range available in VGA mode (without optimizing the
dc offsets).
The speed of the ADL5391 in VGA mode allows it to be used as
an amplitude modulator. Either or both inputs can have
modulation or CW applied. AM modulation is achieved by
feeding CW into X (or Y) and adding AM modulation to the Y
(or X) input.
Squaring and Frequency Doubling
Amplitude domain squaring of an input signal, E, is achieved
simply by connecting the X and Y inputs in parallel to produce
an output of E2. The input can be single-ended, differential, or
through a balun (frequency range and dynamic range can be
limited if used single ended).
The dc component of the output is related to the square of both
the offset (OFST) and the signal input amplitude (E). The offset
can be found in Figure 4 and is approximately 20 mV. The
second harmonic output grows with the square of the input
amplitude, and the signal bleedthrough grows proportionally
with the input signal. For smaller signal amplitudes, the signal
bleedthrough can be higher than the second harmonic
component. As the input amplitude increases, the second
harmonic component grows much faster than the signal
bleedthrough and becomes the dominant signal at the output.
If the X and Y inputs are driven too hard, third harmonic
components will also increase.
For best performance creating harmonics, the ADL5391 should
be driven differentially. Figure 17 shows the performance of the
ADL5391 when used as a harmonic generator (the evaluation
board was used with R9 and R10 removed and R2 = 56.2 Ω). If
dc operation is necessary, the ADL5391 can be driven single
ended (without the dc blocks). The flatness of the response over
a broad frequency range depends on the input/output match.
The fundamental bleed through not only depends on the
amount of power put into the device but also depends on
matching the unused differential input/output to the same
impedance as the used input/output. Figure 18 shows the
performance of the ADL5391 when driven single ended
(without ac coupling capacitors), and Figure 19 shows the
schematic of the setup. A resistive input/output match were
used to match the input from dc to 1 GHz and the output from
dc to 2 GHz. Reactive matching can be used for more narrow
frequency ranges. When matching the input/output of the
ADL5391, care needs to be taken not to load the ADL5391 too
heavily; the maximum reference current available is 50 mA.
–15
When the input is a sine wave Esin(ωt), a signal squarer behaves
as a frequency doubler, because
–20
(3)
–30
GAIN (dBm)
Ideally, when used for squaring and frequency doubling, there is
no component of the original signals on the output. Because of
internal offsets, this is not the case. If Equation 3 were rewritten
to include theses offsets, it could separate into three output
terms (Equation 4).
[Esin(ωt ) + OFST ]× [Esin(ωt ) + OFST ] =
2
E2
[cos(2ωt )] + 2Esin(ωt )OFST + ⎛⎜⎜ OFST 2 + E
2
2
⎝
SECOND HARMONIC GAIN
–25
2
[Esin(ωt )] = E (1 − cos(2ωt ))
2
2
–35
BLEEDTHRU GAIN
–40
–45
–50
–55
THIRD HARMONIC GAIN
–60
⎞
⎟⎟
⎠
(4)
–65
10
100
200
300
400
500
600
700
800
900 1000
FREQUENCY (MHz)
Figure 17. ADL5391 Used as a Harmonic Generator
where:
The dc component is OFST2 + E2/2.
The input signal bleedthrough is 2Esin(ωt)OFST.
The input squared is E2/2[cos(2ωt)].
Rev. 0 | Page 11 of 16
06059-026
Matching the Input/Output
ADL5391
0
be removed through calibration. Figure 20 shows the response
of the ADL5391 as a square law detector, Figure 21 shows the
error vs. the input power, and Figure 22 shows the
configuration used.
BLEEDTHRU GAIN
–5
–10
SECOND HARMONIC GAIN
–15
GAIN (dBm)
–20
–25
0.7
–30
0.6
–35
–40
–45
0.5
THIRD HARMONIC GAIN
VOUT (V)
–50
–55
–65
200
300
400
500
600
700
800
900 1000
FREQUENCY (MHz)
0.2
Figure 18. Single-Ended (DC) ADL5391 Used as a Harmonic Generator
53Ω
XM
74Ω
53Ω
YIN
21Ω
74Ω
XP
WP
YM
WM
YP
150Ω
0.1
10dB PAD
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
VIN (V rms)2
62Ω
Figure 20. ADL5391 Used as Square Law Detector DC Output vs. Square of Input
200Ω
1.6
06059-028
XIN
5dB PAD
21Ω
0.3
06059-091
100
5dB PAD
1.4
Figure 19. Setup for Single-Ended Data
1.2
1.0
ERROR (dB)
Use as a Detector
The ADL5391 can be used as a square law detector. When
amplitude squaring is performed, there are components of the
multiplier output that correlate to the signal bleedthrough and
second harmonic, as seen in Equation 4. However, as noted in
the Squaring and Frequency Doubling section, there is also a dc
component that is directly related to the offset and the squared
input magnitude. If a signal is split and feed into the X and Y
inputs and a low-pass filter were place on the output, the resulting
dc signal would be directly related to the square of the input
magnitude. The intercept of the response will shift slightly from
part to part (and over temperature) with the offset, but this can
0.8
0.6
0.4
0.2
0
–0.2
–30
–25
–20
–15
–10
–5
0
PIN X (dBm)
T3
TC1-1-13M
R2
56.2Ω
C18
0.1µF
11
XM
12
XP
C4
0.1µF
WM 5
T2
C20
0.1µF
WP
TC1-1-13M
R1
56.2Ω
13
YM
14
YP
R4
100Ω
T1
R12
OPEN
R5
24.9Ω
40µH
74µH
45nF
40µH
40nF
74µH
J2
WM
J1
WP
06059-093
J8
XP
R6
24.9Ω
6
10
Figure 21. ADL5391Used as a Square Law Detector Error vs. Power Input
C7
0.1µF
J6
YP
5
06059-092
10
06059-027
–60
0.4
Figure 22. Schematic for ADL5391 Used as Square Law Detector
Rev. 0 | Page 12 of 16
ADL5391
EVALUATION BOARD
C16
OPEN
C7
0.1µF
YP
J6
C6
OPEN
YM
J7
C19
OPEN
XP_DC
TP8
C4
0.1µF
C1
T2
OPEN
XM
J9
C20
0.1µF
TC1-1-13M
XM_DC
TP9
R8
OPEN
ENBL
J10
R20
0Ω
R9
0Ω
R16
OPEN
YMNS
2
3
1
11
10
YPLS
ZPLS
9
GADJ
8
R17
OPEN
14 XMNS
COMM
7
WMNS
6
ADL5391
15 ENBL
R13
OPEN
R6
24.9Ω
R4
100Ω
VMID
TP11
16 VMID
WPLS
COMM
1
VPOS
VPOS
VPOS
2
3
4
R18
0Ω
R19
0Ω
R11
OPEN
ZP
J5
ZM
J4
C17
0.1µF
ZM_DC
TP4
ZMNS
13 XPLS
C9
OPEN
T4
TC1-1-13M
R15
0Ω
R1
56.2Ω
C3
0.1µF
ENBL_DC
TP10
12
C15
OPEN
C8
0.1µF
ZP_DC
TP5
R12
OPEN
GADJ_DC
TP3
GADJ
J3
C14
0.1µF
C5
OPEN
WM_DC
TP2
TC1-1-13M
T1
WM
J2
C2
0.1µF
WP
J1
5
R5
24.9Ω
R7
OPEN
WP_DC
TP1
C13
OPEN
SW1
C10
100pF
C12
0.1µF
TP
TP
COMM
TP14
COMM
TP12
C11
4.7µF
06059-025
XP
J8
YM_DC
TP7
R3
OPEN
R2
OPEN
T3
TC1-1-13M
C18
0.1µF
R14
0Ω
R10
0Ω
YP_DC
TP6
VPOS
TP13
06059-030
06059-031
Figure 23. ADL5391-EVALZ Evaluation Board Schematic
Figure 25. Component Side Silkscreen of Evaluation Board
Figure 24. Component Side Metal of Evaluation Board
Rev. 0 | Page 13 of 16
ADL5391
Table 4. Evaluation Board Configuration Options
Component
J1, J5, J6, J8
J2, J4, J7, J9
J3
T1, T2, T3, T4
C2, C4, C7, C8, C14,
C17, C18, C20
C1, C5, C6, C9, C13,
C15, C16, C19
R9, R10, R14, R15, R18
R19, R20
R7, R13, R16, R17
C10
C12
C3
C11
R1
R2, R3, R12
R5, R6
R4
R8, R11
SW1
TP1, TP2, TP4, TP5,
TP6, TP7, TP8, TP9
TP13
TP12, TP14
TP3, TP10, TP11
DUT
Function
SMA connectors for single-ended, high frequency operation. If J5
and J6 are used, R9, R10, R14, and R15 should be removed. R2 and
R3 should also be populated to match the inputs. If used in broadband
operation, C4, C7, C8, and C2 need to be replaced with 0 Ω resistors.
SMA connectors for broadband differential operation. If these are
used, baluns should be removed and jumped over using 0 Ω
resistors, and C14, C15, C18, and C20 should be removed.
SMA connector for connection to GADJ.
Single-ended-to-differential transformation for high frequency ac
operation. If dc operation is necessary, the baluns can be removed
and jumped over using 0 Ω resistors.
DC block capacitors.
Part Number
Default Value
WP, ZP, YP, XP
WM, ZM, YM, XM
TC1-1-13M+
Mini-Circuits
GADJ
T3 and T4 are populated,
but the Y and Z inputs
are set up for dc operation.
0.1 μF, 0402 capacitors
Not installed, dc block capacitors.
Open, 0402 capacitors
Snubbing resistors.
Snubbing resistors.
Snubbing resistors.
Filter capacitor.
Filter capacitor.
Filter capacitor.
Filter capacitor.
Matching resistor.
Matching resistors. Input impedance to X, Y, and Z inputs are the
same. For the same frequency, R1, R2, and R3 should be the same.
Matching resistor.s
Matching resistor.
Can be used for voltage divider or filtering.
Enable switch: enable = 5 V, disable = 0 V.
Green test loop.
0 Ω, 0402 resistors
0 Ω, 0603 resistors
Open, 0402 resistors
100 pF, 0402 capacitor
0.1 μF, 0402 capacitor
0.1 μF, 0603 capacitor
4.7 μF, 3216 capacitor
56.2 Ω, 0603 resistor
Open, 0603 resistors
Red test loop.
Black test loops.
Yellow test loops.
ADL5391.
24.9 Ω, 0402 resistors
100 Ω, 0603 resistor
Open, 0603 resistors
SW1 installed
WP_DC, WM_DC,
ZM_DC, ZP_DC, YP_DC,
YM_DC, XP_DC, XM_DC
VPOS
COMM
GADJ_DC, ENBL_DC, VMID
ADL5391ACPZ
Rev. 0 | Page 14 of 16
ADL5391
OUTLINE DIMENSIONS
3.00
BSC SQ
0.60 MAX
0.45
PIN 1
INDICATOR
TOP
VIEW
13
12
2.75
BSC SQ
0.80 MAX
0.65 TYP
12° MAX
SEATING
PLANE
16
PIN 1
INDICATOR
*1.65
1.50 SQ
1.35
1
EXPOSED
PAD
0.50
BSC
0.90
0.85
0.80
0.50
0.40
0.30
9 (BOTTOM VIEW) 4
8
5
0.25 MIN
1.50 REF
0.05 MAX
0.02 NOM
0.30
0.23
0.18
0.20 REF
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2
EXCEPT FOR EXPOSED PAD DIMENSION.
Figure 26. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
3 mm × 3 mm Body, Very Thin Quad
(CP-16-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADL5391ACPZ-R2 1
ADL5391ACPZ-R71
ADL5391ACPZ-WP1
ADL5391-EVALZ1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
Evaluation Board
Z = Pb-free part.
Rev. 0 | Page 15 of 16
Package Option
CP-16-3
CP-16-3
CP-16-3
Ordering Quantity
250
1,500
50
1
ADL5391
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06059-0-7/06(0)
T
T
Rev. 0 | Page 16 of 16
Similar pages