FET BIAS CONTROLLER ZNBG3000 ZNBG3001 ISSUE 1- AUGUST 1998 DEVICE DESCRIPTION It is possible to use less than the devices full complement of FET bias controls, unused drain and gate connections can be left open circuit without affecting operation of the remaining bias circuits. The ZNBG series of devices are designed to meet the bias requirements of GaAs and HEMT FETs commonly used in satellite receiver LNBs, PMR, cellular telephones etc. with a minimum of external components. In order to protect the external FETs the circuits have been designed to ensure that, under any conditions including power up/down transients, the gate drive from the bias circuits cannot exceed the range -3.5V to 0.7V. Furthermore if the negative rail experiences a fault condition, such as overload or short circuit, the drain supply to the FETs will shut down avoiding excessive current flow. With the addition of two capacitors and a resistor the devices provide drain voltage and current control for 3 external grounded source FETs, generating the regulated negative rail required for FET gate biasing whilst operating from a single supply. This negative bias, at -3 volts, can also be used to supply other external circuits. The ZNBG3000/1 contains three bias stages. A single resistor allows FET drain current to be set to the desired level. The series also offers the choice of drain voltage to be set for the FETs, the ZNBG3000 gives 2.2 volts drain whilst the ZNBG3001 gives 2 volts. The ZNBG3000/1 are available in QSOP16 packages for the minimum in devices size. Device operating temperature is -40 to 70°C to suit a wide range of environmental conditions. These devices are unconditionally stable over the full working temperature with the FETs in place, subject to the inclusion of the recommended gate and drain capacitors. These ensure RF stability and minimal injected noise. FEATURES APPLICATIONS • • • • • • • • • • • • Provides bias for GaAs and HEMT FETs Drives up to three FETs Dynamic FET protection Drain current set by external resistor Regulated negative rail generator requires only 2 external capacitors Choice in drain voltage Wide supply voltage range QSOP surface mount package 4-137 Satellite receiver LNBs Private mobile radio (PMR) Cellular telephones Single in single out C Band LNB ZNBG3000 ZNBG3001 ABSOLUTE MAXIMUM RATINGS Supply Voltage Supply Current Drain Current (per FET) (set by RCAL1 and RCAL2) Output Current Operating Temperature Storage Temperature Power Dissipation (Tamb= 25°C) QSOP16 500mW -0.6V to 15V 100mA 0 to 15mA 100mA -30 to 70°C -40 to 85°C ELECTRICAL CHARACTERISTICS TEST CONDITIONS (Unless otherwise stated): Tamb= 25°C,VCC=5V,ID=10mA (RCAL1 =33kΩ) Ω) SYMBOL PARAMETER LIMITS CONDITIONS Min VCC Supply Voltage ICC Supply Current ID1 to ID3=0 ID1 to ID3=10mA VSUB Substrate Voltage (Internally generated) ISUB= 0 ISUB= -200µA END ENG Output Noise Drain Voltage Gate Voltage CG=4.7nF, CD=10nF CG=4.7nF, CD=10nF fO Oscillator Freq. Typ 5 -3.5 200 UNITS Max 12 V 10 40 mA mA -2 -2 V V 0.02 0.005 Vpkpk Vpkpk 330 800 kHz 15 mA 10 12 mA -2.8 DRAIN CHARACTERISTICS IDO Output Current Range ID Current Set by RCAL1 0 8 Current Change ∆IDV with VCC VCC=5 to 12V 0.5 %/V ∆IDT with Tj Tj=-30 to +70°C 0.05 %/°C VD Voltage ZNBG3000 ID1 to ID3=10mA ZNBG3001 2 1.8 2.2 2 2.4 2.2 V V Voltage Change ∆VDV with VCC VCC= 5 to 12V 0.5 %/V ∆VDT with Tj Tj = -30 to +70°C 50 ppm 4-138 ZNBG3000 ZNBG3001 SYMBOL PARAMETER LIMITS CONDITIONS Min Typ UNITS Max GATE CHARACTERISTICS IGO -30 2000 µA ID1 to ID3=12mA IG1 to IG3=0 -3.5 -2 V ID1 to ID3=12mA IG1 to IG3= -10µA -3.5 -2 V ID1 to ID3= 8mA IG1 to IG3= 0 0.4 1 V Output Current Range Output Voltage VOL VOH Output Low Output High Notes: 1. The negative bias voltages specified are generated on-chip using an internal oscillator. Two external capacitors, CNB and CSUB, of 47nF are required for this purpose. 2. The characteristics are measured using an external reference resistors RCAL1 of value 33kΩ wired from pin RCAL1 to ground. 3. Noise voltage is not measured in production. 4. Noise voltage measurement is made with FETs and gate and drain capacitors in place on all outputs. CG, 4.7nF, are connected between gate outputs and ground, CD, 10nF, are connected between drain outputs and ground. 4-139 ZNBG3000 ZNBG3001 TYPICAL CHARACTERISTICS 16 Note:- Operation with loads > 200µA is not guaranteed. Vcc = 5V 14 0.0 12 -0.5 10 -1.0 8 -1.5 6 -2.0 4 -2.5 2 -3.0 Vcc = 5V 6V 8V 10V 0 0 10 20 30 40 50 0 0.2 Rcal (k) 0.4 0.6 0.8 1.0 External Vsub Load (mA) JFET Drain Current v Rcal Vsub v External Load 2.4 2.2 ZNBG3000 ZNBG3001 2.3 2.1 2.2 2.0 Vcc = 5V 6V 8V 10V 2.1 Vcc = 5V 6V 8V 10V 1.9 2.0 1.8 2 4 6 8 10 12 14 16 2 Drain Current (mA) 4 6 8 10 12 14 Drain Current (mA) JFET Drain Voltage v Drain Current JFET Drain Voltage v Drain Current 4-140 16 ZNBG3000 ZNBG3001 FUNCTIONAL DIAGRAM FUNCTIONAL DESCRIPTION The ZNBG devices provide all the bias requirements for external FETs, including the generation of the negative supply required for gate biasing, from the single supply voltage. The diagram above shows a single stage from the ZNBG series. The ZNBG3000/1 contains 3 such stages. The drain voltage of the external FET QN is set by the ZNBG device to its normal operating voltage. This is determined by the on board VD Set reference, for the ZNBG3000 this is nominally 2.2 volts whilst the ZNBG3001 provides nominally 2 volts. The drain current taken by the FET is monitored by the low value resistor ID Sense. The amplifier driving the gate of the FET adjusts the gate voltage of QN so that the drain current taken matches the current called for by an external resistor RCAL. Both ZNBG devices have the facility to program different drain currents into selected FETs. Since the FET is a depletion mode transistor, it is usually necessary to drive its gate negative with respect to ground to obtain the required drain current. To provide this capability powered from a single positive supply, the device includes a low current negative supply generator. This generator uses an internal oscillator and two external capacitors, CNB and CSUB. 4-141 ZNBG3000 ZNBG3001 TYPICAL APPLICATION CIRCUIT APPLICATIONS INFORMATION The above is a partial application circuit for the ZNBG series showing all external components required for appropriate biasing. The bias circuits are unconditionally stable over the full temperature range with the associated FETs and gate and drain capacitors in circuit. Capacitors CD and CG ensure that residual power supply and substrate generator noise is not allowed to affect other external circuits which may be sensitive to RF interference. They also serve to suppress any potential RF feedthrough between stages via the ZNBG device. These capacitors are required for all stages used. Values of 10nF and 4.7nF respectively are recommended however this is design dependent and any value between 1nF and 100nF could be used. The capacitors CNB and CSUB are an integral part of the ZNBGs negative supply generator. The negative bias voltage is generated on-chip using an internal oscillator. The required value of capacitors CNB and CSUB is 47nF. This generator produces a low current supply of approximately -3 volts. Although this generator is intended purely to bias the external FETs, it can be used to power other external circuits via the CSUB pin. Resistor RCAL1 sets the drain current at which all external FETs are operated. If any bias control circuit is not required, its related drain and gate connections may be left open circuit without affecting the operation of the remaining bias circuits. If all FETs associated with a current setting resistor are omitted, the particular RCAL should still be included. The supply current can be reduced, if required, by using a high value RCAL resistor (e.g. 470k). 4-142 ZNBG3000 ZNBG3001 APPLICATIONS INFORMATION (Continued) The ZNBG devices have been designed to protect the external FETs from adverse operating conditions. With a JFET connected to any bias circuit, the gate output voltage of the bias circuit can not exceed the range -3.5V to 0.7V, under any conditions including powerup and powerdown transients. Should the negative bias generator be shorted or overloaded so that the drain current of the external FETs can no longer be controlled, the drain supply to FETs is shut down to avoid damage to the FETs by excessive drain current. The following diagram show the ZNBG3000/1 in typical LNB applications. Single in/Single out C band LNB block diagram 4-143 ZNBG3000 ZNBG3001 CONNECTION DIAGRAMS ORDERING INFORMATION Part Number Package Part Mark ZNBG3000Q16 QSOP16 ZNBG3000 ZNBG3001Q16 QSOP16 ZNBG3001 PACKAGE DIMENSIONS A IDENTIFICATION RECESS FOR PIN 1 C B D PIN No.1 K PIN Millimetres Inches E 3.81 MIN MAX MIN A 4.80 4.90 0.033 B 0.635 C 0.177 D 0.20 3.99 0.15 0.157 MAX F 1.35 1.75 0.053 0.069 0.039 G 0.10 0.25 0.004 0.01 0.025 NOM J 5.79 6.20 0.228 0.244 0.267 0.007 0.011 K 0° 8° 0° 8° 0.30 0.008 0.012 Zetex plc. Fields New Road, Chadderton, Oldham, OL9-8NP, United Kingdom. Telephone: (44)161 622 4422 (Sales), (44)161 622 4444 (General Enquiries) Fax: (44)161 622 4420 Zetex GmbH Streitfeldstraße 19 D-81673 München Germany Telefon: (49) 89 45 49 49 0 Fax: (49) 89 45 49 49 49 Zetex Inc. 47 Mall Drive, Unit 4 Commack NY 11725 USA Telephone: (516) 543-7100 Fax: (516) 864-7630 Zetex (Asia) Ltd. 3510 Metroplaza, Tower 2 Hing Fong Road, Kwai Fong, Hong Kong Telephone:(852) 26100 611 Fax: (852) 24250 494 These are supported by agents and distributors in major countries world-wide Zetex plc 1998 Internet:http://www.zetex.com This publication is issued to provide outline information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose or form part of any order or contract or be regarded as a representation relating to the products or services concerned. The Company reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service. 4-145 ZNBG4000 ZNBG4001 ZNBG6000 ZNBG6001 ZNBG3000 ZNBG3001 PACKAGE DIMENSIONS A IDENTIFICATION RECESS FOR PIN 1 C B D PIN No.1 K PIN Millimetres Inches E 3.81 3.99 0.15 0.157 MIN MAX MIN MAX F 1.35 1.75 0.053 0.069 A 4.80 4.90 0.033 0.039 G 0.10 0.25 0.004 0.01 B 0.635 0.025 NOM J 5.79 6.20 0.228 0.244 C 0.177 0.267 0.007 0.011 K 0° 8° 0° 8° D 0.20 0.30 0.008 0.012 Page Number