Catalyst CAT24C64WI-GT2 64-kb i2c cmos serial eeprom Datasheet

CAT24C64
64-Kb I2C CMOS Serial EEPROM
FEATURES
DEVICE DESCRIPTION
■ Supports Standard and Fast I2C Protocol
The CAT24C64 is a 64-Kb CMOS Serial EEPROM
devices, internally organized as 128 pages of 64 bytes
each.
■ 1.8 V to 5.5 V Supply Voltage Range
■ 32-Byte Page Write Buffer(1)
It features a 32-byte page write buffer and supports
both the Standard (100 kHz) as well as Fast (400 kHz)
I2C protocol.
■ Hardware Write Protection for entire memory
■ Schmitt Triggers and Noise Suppression Filters
on I2C Bus Inputs (SCL and SDA).
External address pins make it possible to address up to
eight CAT24C64 devices on the same bus.
■ Low power CMOS technology
■ 1,000,000 program/erase cycles
■ 100 year data retention
■ Industrial temperature range
■ RoHS-compliant 8-pin PDIP, SOIC, TSSOP and
TDFN packages
Note:
(1) CAT24C64 Rev. D (Not Recommended for New Designs) has
64-Byte Page Write Buffer.
For Ordering Information details, see page 15.
PIN CONFIGURATION
FUNCTIONAL SYMBOL
PDIP (L)
SOIC (W)
TSSOP (Y)
TDFN (ZD2, VP2)
A0
1
8
VCC
A1
A2
2
7
WP
3
6
SCL
VSS
4
5
SDA
VCC
SCL
A2, A1, A0
For the location of Pin 1, please consult the
corresponding package drawing.
Device Address
SDA
Serial Data
SCL
Serial Clock
WP
Write Protect
VCC
Power Supply
VSS
Ground
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
SDA
WP
PIN FUNCTIONS
A0, A1, A2
CAT24C64
VSS
* The Green & Gold seal identifies RoHS-compliant packaging, using NiPdAu
pre-plated lead frames.
1
Doc. No. 1102, Rev. H
CAT24C64
ABSOLUTE MAXIMUM RATINGS(1)
Storage Temperature
-65°C to +150°C
Voltage on Any Pin with Respect to Ground(2)
-0.5 V to +6.5 V
RELIABILITY CHARACTERISTICS(3)
Symbol
Parameter
Min
Units
NEND(4)
Endurance
1,000,000
Program/ Erase Cycles
100
Years
TDR
Data Retention
D.C. OPERATING CHARACTERISTICS
VCC = 1.8 V to 5.5 V, TA = -40°C to 85°C, unless otherwise specified.
Symbol
Parameter
Test Conditions
ICCR
Read Current
ICCW
Min
Max
Units
Read, fSCL = 400 kHz
1
mA
Write Current
Write, fSCL = 400 kHz
1
mA
ISB
Standby Current
All I/O Pins at GND or VCC
1
μA
IL
I/O Pin Leakage
Pin at GND or VCC
1
μA
VIL
Input Low Voltage
VCC x 0.3
V
VIH
Input High Voltage
VCC x 0.7 VCC + 0.5
V
VOL1
Output Low Voltage
VCC ≥ 2.5 V, IOL = 3.0 mA
0.4
V
VOL2
Output Low Voltage
VCC < 2.5 V, IOL = 1.0 mA
0.2
V
Max
Units
-0.5
PIN IMPEDANCE CHARACTERISTICS
VCC = 1.8 V to 5.5 V, TA = -40°C to 85°C, unless otherwise specified.
Symbol
Parameter
Conditions
CIN(3)
SDA I/O Pin Capacitance
VIN = 0 V
8
pF
CIN(3)
Input Capacitance (other pins)
VIN = 0 V
6
pF
IWP(5)
WP Input Current
VIN < VIH
100
VIN > VIH
1
μA
Note:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification
is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The DC input voltage on any pin should not be lower than -0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than -1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns.
(3) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Page Mode, VCC = 5 V, 25°C
(5) When not driven, the WP pin is pulled down to GND internally. For improved noise immunity, the internal pull-down is relatively strong;
therefore the external driver must be able to supply the pull-down current when attempting to drive the input HIGH. To conserve power, as
the input level exceeds the trip point of the CMOS input buffer (~ 0.5 x VCC), the strong pull-down reverts to a weak current source.
Doc. No. 1102, Rev. H
2
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
A.C. CHARACTERISTICS(1)
VCC = 1.8 V to 5.5 V, TA = -40°C to 85°C.
Standard
Symbol
FSCL
tHD:STA
Min
Parameter
Max
Clock Frequency
Fast
Min
100
START Condition Hold Time
Max
Units
400
kHz
4
0.6
μs
tLOW
Low Period of SCL Clock
4.7
1.3
μs
tHIGH
High Period of SCL Clock
4
0.6
μs
4.7
0.6
μs
tSU:STA
START Condition Setup Time
tHD:DAT
Data In Hold Time
0
0
μs
tSU:DAT
Data In Setup Time
250
100
ns
tR
SDA and SCL Rise Time
1000
300
ns
tF(2)
SDA and SCL Fall Time
300
300
ns
tSU:STO
STOP Condition Setup Time
tBUF
Bus Free Time Between STOP and START
tAA
SCL Low to Data Out Valid
tDH
Data Out Hold Time
Ti(2)
Noise Pulse Filtered at SCL and SDA Inputs
4
0.6
μs
4.7
1.3
μs
3.5
100
0.9
100
100
μs
ns
100
ns
tSU:WP
WP Setup Time
0
0
μs
tHD:WP
WP Hold Time
2.5
2.5
μs
tWR
tPU(2, 3)
Write Cycle Time
5
5
ms
Power-up to Ready Mode
1
1
ms
Note:
(1) Test conditions according to “A.C. Test Conditions” table.
(2) Tested initially and after a design or process change that affects this parameter.
(3) tPU is the delay between the time VCC is stable and the device is ready to accept commands.
A.C. TEST CONDITIONS
Input Levels
0.2 x VCC to 0.8 x VCC
Input Rise and Fall Times
≤ 50 ns
Input Reference Levels
0.3 x VCC, 0.7 x VCC
Output Reference Levels
0.5 x VCC
Output Load
Current Source: IOL = 3 mA (VCC ≥ 2.5 V); IOL = 1 mA (VCC < 2.5 V); CL = 100 pF
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
3
Doc No. 1102, Rev. H
CAT24C64
POWER-ON RESET (POR)
FUNCTIONAL DESCRIPTION
Each CAT24C64 incorporates Power-On Reset (POR)
circuitry which protects the internal logic against powering
up in the wrong state. The device will power up into
Standby mode after VCC exceeds the POR trigger level
and will power down into Reset mode when VCC drops
below the POR trigger level. This bi-directional POR
behavior protects the device against ‘brown-out’ failure
following a temporary loss of power.
The CAT24C64 supports the Inter-Integrated Circuit
(I2C) Bus protocol. The protocol relies on the use of a
Master device, which provides the clock and directs bus
traffic, and Slave devices which execute requests. The
CAT24C64 operates as a Slave device. Both Master
and Slave can transmit or receive, but only the Master
can assign those roles.
I2C BUS PROTOCOL
The 2-wire I2C bus consists of two lines, SCL and SDA,
connected to the VCC supply via pull-up resistors. The
Master provides the clock to the SCL line, and either the
Master or the Slaves drive the SDA line. A ‘0’ is transmitted
by pulling a line LOW and a ‘1’ by letting it stay HIGH.
Data transfer may be initiated only when the bus is not
busy (see A.C. Characteristics). During data transfer,
SDA must remain stable while SCL is HIGH.
START/STOP Condition
An SDA transition while SCL is HIGH creates a START
or STOP condition (Figure 1). The START consists of a
HIGH to LOW SDA transition, while SCL is HIGH. Absent
the START, a Slave will not respond to the Master. The
STOP completes all commands, and consists of a LOW
to HIGH SDA transition, while SCL is HIGH.
PIN DESCRIPTION
SCL: The Serial Clock input pin accepts the clock signal
generated by the Master.
Device Addressing
The Master addresses a Slave by creating a START
condition and then broadcasting an 8-bit Slave address.
For the CAT24C64, the first four bits of the Slave address
are set to 1010 (Ah); the next three bits, A2, A1 and A0,
must match the logic state of the similarly named input
pins. The R/
R/W
W bit tells the Slave whether the Master
intends to read (1) or write (0) data (Figure 2).
SDA: The Serial Data I/O pin accepts input data and
delivers output data. In transmit mode, this pin is open
drain. Data is acquired on the positive edge, and is
delivered on the negative edge of SCL.
A0, A1 and A2: The Address inputs set the device address that must be matched by the corresponding Slave
address bits. The Address inputs are hard-wired HIGH
or LOW allowing for up to eight devices to be used
(cascaded) on the same bus. When left floating, these
pins are pulled LOW internally.
Acknowledge
During the 9th clock cycle following every byte sent to
the bus, the transmitter releases the SDA line, allowing the receiver to respond. The receiver then either
acknowledges (ACK) by pulling SDA LOW, or does not
acknowledge (NoACK) by letting SDA stay HIGH (Figure
3). Bus timing is illustrated in Figure 4.
WP: When pulled HIGH, the Write Protect input pin
inhibits all write operations. When left floating, this pin
is pulled LOW internally.
Doc. No. 1102, Rev. H
4
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
Figure 1. Start/Stop Timing
SCL
SDA
START
CONDITION
STOP
CONDITION
Figure 2. Slave Address Bits
1
0
1
0
A2
A1
A0
R/W
DEVICE ADDRESS
Figure 3. Acknowledge Timing
BUS RELEASE DELAY (TRANSMITTER)
SCL FROM
MASTER
1
BUS RELEASE DELAY (RECEIVER)
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACK SETUP (≥ tSU:DAT)
ACK DELAY (≤ tAA)
Figure 4. Bus Timing
tF
tHIGH
tLOW
tR
tLOW
SCL
tSU:STA
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
SDA IN
tAA
tDH
tBUF
SDA OUT
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc No. 1102, Rev. H
CAT24C64
WRITE OPERATIONS
Byte Write
To write data to memory, the Master creates a START
condition on the bus and then broadcasts a Slave address with the R/
R/W
W bit set to ‘0’. The Master then sends
two address bytes and a data byte and concludes the
session by creating a STOP condition on the bus. The
Slave responds with ACK after every byte sent by the
Master (Figure 5). The STOP starts the internal Write
cycle, and while this operation is in progress (tWR), the
SDA output is tri-stated and the Slave does not acknowledge the Master (Figure 6).
Page Write
The Byte Write operation can be expanded to Page
Write, by sending more than one data byte to the Slave
before issuing the STOP condition (Figure 7). Up to
32(1) distinct data bytes can be loaded into the internal
Page Write Buffer starting at the address provided by
the Master. The page address is latched, and as long
as the Master keeps sending data, the internal byte address is incremented up to the end of page, where it then
wraps around (within the page). New data can therefore
replace data loaded earlier. Following the STOP, data
loaded during the Page Write session will be written to
memory in a single internal Write cycle (tWR).
Acknowledge Polling
As soon (and as long) as internal Write is in progress,
the Slave will not acknowledge the Master. This feature
enables the Master to immediately follow-up with a new
Read or Write request, rather than wait for the maximum
specified Write time (tWR) to elapse. Upon receiving a
NoACK response from the Slave, the Master simply repeats the request until the Slave responds with ACK.
Hardware Write Protection
With the WP pin held HIGH, the entire memory is protected
against Write operations. If the WP pin is left floating or
is grounded, it has no impact on the Write operation. The
state of the WP pin is strobed on the last falling edge
of SCL immediately preceding the 1st data byte (Figure
8). If the WP pin is HIGH during the strobe interval, the
Slave will not acknowledge the data byte and the Write
request will be rejected.
Delivery State
The CAT24C64 is shipped erased, i.e., all bytes are
FFh.
Note:
(1) CAT24C64 Rev. D (Not Recommended for New Designs) has
64-Byte Page Write Buffer.
Doc. No. 1102, Rev. H
6
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
Figure 5. Byte Write Sequence
BUS ACTIVITY:
MASTER
S
T
A
R
T
SLAVE
ADDRESS
S
ADDRESS
BYTE
DATA
BYTE
DATA
BYTE
a15 ÷ a8
a7 ÷ a 0
d7 ÷ d 0
S
T
O
P
P
** *
A
C
K
SLAVE
A
C
K
A
C
K
A
C
K
* a15 ÷ a13 are don't care bits.
Figure 6. Write Cycle Timing
SCL
8th Bit
Byte n
SDA
ACK
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
Figure 7. Page Write Sequence
BUS ACTIVITY:
MASTER
S
T
A
R
T
ADDRESS
BYTE
SLAVE
ADDRESS
DATA
BYTE
n
ADDRESS
BYTE
DATA
BYTE
n+1
S
T
O
P
DATA
BYTE
n+P
S
P
A
C
K
SLAVE
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
Figure 8. WP Timing
ADDRESS
BYTE
DATA
BYTE
1
8
a7
a0
9
1
8
d7
d0
SCL
SDA
tSU:WP
WP
tHD:WP
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc No. 1102, Rev. H
CAT24C64
READ OPERATIONS
Immediate Read
To read data from memory, the Master creates a START
condition on the bus and then broadcasts a Slave address with the R/
R/W
W bit set to ‘1’. The Slave responds with
ACK and starts shifting out data residing at the current
address. After receiving the data, the Master responds
with NoACK and terminates the session by creating a
STOP condition on the bus (Figure 9). The Slave then
returns to Standby mode.
Selective Read
To read data residing at a specific address, the selected
address must first be loaded into the internal address
register. This is done by starting a Byte Write sequence,
whereby the Master creates a START condition, then
broadcasts a Slave address with the R/W bit set to ‘0’
and then sends two address bytes to the Slave. Rather
than completing the Byte Write sequence by sending
data, the Master then creates a START condition and
broadcasts a Slave address with the R/
R/W
W bit set to ‘1’.
The Slave responds with ACK after every byte sent by the
Master and then sends out data residing at the selected
address. After receiving the data, the Master responds
with NoACK and then terminates the session by creating
a STOP condition on the bus (Figure 10).
Sequential Read
If, after receiving data sent by the Slave, the Master
responds with ACK, then the Slave will continue transmitting until the Master responds with NoACK followed by
STOP (Figure 11). During Sequential Read the internal
byte address is automatically incremented up to the end
of memory, where it then wraps around to the beginning
of memory.
Doc. No. 1102, Rev. H
8
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
Figure 9. Immediate Read Sequence and Timing
BUS ACTIVITY:
MASTER
S
T
A
R
T
N
O
S
AT
CO
KP
SLAVE
ADDRESS
S
P
A
C
K
SLAVE
SCL
8
DATA
BYTE
9
8th Bit
SDA
DATA OUT
NO ACK
STOP
Figure 10. Selective Read Sequence
BUS ACTIVITY:
MASTER
S
T
A
R
T
ADDRESS
BYTE
SLAVE
ADDRESS
S
T
A
R
T
ADDRESS
BYTE
S
N
O
S
AT
CO
KP
SLAVE
ADDRESS
S
A
C
K
SLAVE
A
C
K
P
A
C
K
A
C
K
DATA
BYTE
Figure 11. Sequential Read Sequence
N
O
BUS ACTIVITY:
MASTER
A
C
K
SLAVE
ADDRESS
A
C
K
S
AT
CO
KP
A
C
K
P
SLAVE
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
A
C
K
DATA
BYTE
n
DATA
BYTE
n+1
9
DATA
BYTE
n+2
DATA
BYTE
n+x
Doc No. 1102, Rev. H
CAT24C64
8-LEAD 300 MIL WIDE PLASTIC DIP (L)
E1
E
D
A2
A
A1
L
e
eB
b2
b
SYMBOL
A
A1
A2
b
b2
D
E
E1
e
eB
L
MIN
NOM
MAX
4.57
0.38
3.05
0.36
1.14
9.02
7.62
6.09
7.87
0.115
0.46
7.87
6.35
2.54 BSC
0.130
3.81
0.56
1.77
10.16
8.25
7.11
9.65
0.150
24C32_64_8-LEAD_DIP_(300P).eps
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters.
2. Complies with JEDEC Standard MS001.
3. Dimensioning and tolerancing per ANSI Y14.5M-1982
Doc. No. 1102, Rev. H
10
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
8-LEAD 150 MIL WIDE SOIC (W)
E1
E
h x 45
D
C
A
θ1
e
A1
L
b
SYMBOL
MIN
A1
A
b
C
D
E
E1
e
h
L
θ1
0.10
1.35
0.33
0.19
4.80
5.80
3.80
NOM
MAX
0.25
1.75
0.51
0.25
5.00
6.20
4.00
1.27 BSC
0.25
0.40
0°
0.50
1.27
8°
24C32_64_8-LEAD_SOIC.eps
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters.
2. Complies with JEDEC specification MS-012 dimensions.
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc No. 1102, Rev. H
CAT24C64
8-LEAD TSSOP (Y)
D
5
8
SEE DETAIL A
c
E
E1
E/2
GAGE PLANE
4
1
PIN #1 IDENT.
0.25
θ1
L
A2
SEATING PLANE
SEE DETAIL A
A
e
A1
b
SYMBOL
A
A1
A2
b
c
D
E
E1
e
L
θ1
MIN
0.05
0.80
0.19
0.09
2.90
6.30
4.30
0.50
0.00
NOM
0.90
3.00
6.4
4.40
0.65 BSC
0.60
MAX
1.20
0.15
1.05
0.30
0.20
3.10
6.50
4.50
0.75
8.00
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters.
2. Complies with JEDEC specification MO-153.
Doc. No. 1102, Rev. H
12
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
8-LEAD TDFN 3X4.9 PACKAGE (ZD2)
SYMBOL
MIN
NOM
MAX
A
0.70
0.75
0.80
A1
0.00
0.02
0.05
A2
0.45
0.55
0.65
A3
0.20 R E F
b
0.25
0.30
0.35
D
2.90
3.00
3.10
D2
0.90
1.00
1.10
E
4.80
4.90
5.00
E2
0.90
1.00
1.10
e
L
0.65 T Y P
0.50
0.60
0.70
Notes:
(1) All dimensions are in millimeters.
Angles inTape
degree.
For current
and
(2) Complies with JEDEC MO-229.
Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters. Angles in degree.
2. Complies with JEDEC MO-229.
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
13
Doc No. 1102, Rev. H
CAT24C64
CAT4004
8-LEAD
TDFN 2x3
(VP2)
PACKAGE
OUTLINES
8 LEAD TDFN (VP2) 2mm x 3mm
A
E
PIN 1 INDEX AREA
A1
D
D2
A2
A3
SYMBOL
MIN
NOM
MAX
A
A1
A2
A3
b
D
D2
E
E2
e
L
0.70
0.00
0.45
0.75
0.02
0.55
0.20 REF
0.25
2.00
1.40
3.00
1.30
0.50 TYP
0.30
0.80
0.05
0.65
0.20
1.90
1.30
2.90
1.20
0.20
E2
0.30
2.10
1.50
3.10
1.40
PIN 1 ID
L
0.40
b
e
3xe
For current Tape & Reel information, download the pdf file from:
http://www.catsemi.com/documents/tapeandreel.pdf
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters, angles in degrees.
Notes: (2) Complies with JEDEC Standard
1. All dimensions are in millimeters, angles in degrees.
2. Complies with JEDEC Standard MO-229.
© 2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc. No. 1102, Rev. H
9
14
Doc. No. 5024 Rev. A
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
EXAMPLE OF ORDERING INFORMATION
Prefix
Device #
CAT
Company ID
Suffix
24C64
Y
Product Number
24C64
L:
W:
Y:
ZD2:
VP2:
I
–
G
Temperature Range
I = Industrial (-40°C to +85°C)
Package
PDIP
SOIC, JEDEC
TSSOP
TDFN (3x4.9)(5)
TDFN (2x3)
T3
T: Tape & Reel
2: 2000/Reel
3: 3000/Reel
Lead Finish
G: NiPdAu
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The standard lead finish is NiPdAu on pre-plated (PPF) lead frames.
(3) The device used in the above example is a CAT24C64YI-GT3 (TSSOP, Industrial Temperature, NiPdAu, Tape & Reel).
(4) For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office.
(5) TDFN, ZD2 is only available in 2000 pcs/reel, i.e., CAT24C64ZD2I-T2. The TDFN (3x4.9) package is not recommended for new designs.
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
15
Doc No. 1102, Rev. H
CAT24C64
REVISION HISTORY
Date
Revision Comments
10/07/05
A
Initial Issue
11/16/05
B
Update Ordering Information
Add Tape and Reel Specifications
02/02/06
C
Update Ordering Information
08/23/06
D
Updated device description, supporting text and figures, package outlines, package
marking and ordering information.
Updated and re-formatted D.C. Characteristics presentation.
Updated and re-formatted A.C. Characteristics presentation to reflect
Standard (100 kHz) and Fast (400 kHz) operation over the full voltage range.
09/08/06
E
Remove Package Marking
02/13/07
F
Update TDFN 8 Lead (3x4.9mm) package
03/20/07
G
Add TDFN 8 Lead (2x3mm) package
03/29/07
H
Update Page Write Buffer to 32-Bytes (for CAT24C64 Rev. E)
Doc. No. 1102, Rev. H
16
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C64
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
Beyond Memory ™, DPP ™, EZDim ™, MiniPot™, and Quad-Mode™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation
where personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets
labeled “Advance Information” or “Preliminary” and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical
semiconductor applications and may not be complete.
© 2007 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
17
Doc No. 1102, Rev. H
Catalyst Semiconductor, Inc.
Corporate Headquarters
2975 Stender Way
Santa Clara, CA 95054
Phone: 408.542.1000
Fax: 408.542.1200
www.catsemi.com
Publication #:
Revison:
Issue date:
1102
H
03/29/07
Similar pages