Kingbright AA3528SYC 3.5x2.8 mm smd chip led lamp Datasheet

3.5x2.8 mm SMD CHIP LED LAMP
AA3528SYC
SUPER BRIGHT YELLOW
Description
Features
The Super Bright Yellow device is made with DH InGaAlP
SINGLE COLOR.
SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER
(on GaAs substrate) light emitting diode chip.
PROCESS.
AVAILABLE ON TAPE AND REEL.
IDEAL FOR BACKLIGHTING.
PACKAGE : 1500PCS / REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Specifications are subject to change without notice.
SPEC NO: DSAD1231
REV NO: V.4
DATE:MAR/09/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN:Y.CHENG
ERP:1201000411
Selection Guide
Part No.
Dice
SUPER BRIGHT YELLOW (InGaAIP)
AA3528SYC
Iv (mcd)
@ 20mA
Lens Type
WATER CLEAR
Viewing
Angle
Min.
Typ.
2θ
θ1/2
36
120
120°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Yellow
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Super Bright Yellow
588
nm
IF=20mA
Spectral Line Half-width
Super Bright Yellow
28
nm
IF=20mA
C
Capacitance
Super Bright Yellow
25
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Yellow
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Yellow
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
DC Forward Current
50
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1231
REV NO: V.4
DATE:MAR/09/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN:Y.CHENG
ERP:1201000411
Super Bright Yellow
AA3528SYC
SPEC NO: DSAD1231
REV NO: V.4
DATE:MAR/09/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN:Y.CHENG
ERP:1201000411
AA3528SYC
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
D
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength), the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD1231
REV NO: V.4
DATE:MAR/09/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN:Y.CHENG
ERP:1201000411
Similar pages