NKK FP0115CAC1FF-C2 Contactless pushbutton Datasheet

Contactless Pushbuttons
Series FP01
Distinctive Characteristics
Brilliant illumination for highly visible status indication
with LEDs and caps in red, green, or amber; subdued
illumination for low light requirements with white cap
over red, green, or amber LEDs.
Photo interrupter, rather than contacts, ensures
high reliability and long life of 3 million
operations minimum.
Rugged construction and smooth actuation allow
repeated, rapid actuation force anywhere on cap
surface.
Snap-in mounting for easy installation.
Connector socket with 6 pins for simple connection.
Well suited for gaming and vending machines, as
well as equipment exposed to corrosive gases used in
environments such as chemical or steel manufacturing plants.
Actual Size
FP01-15
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Contactless Pushbuttons
Series FP01
TYPICAL SWITCH ORDERING EXAMPLE
FP01
1
5
C
PHOTO TRANSISTOR
1
5
C
Unshaded
(Shaded)
C1
A
C1
Round
HOUSING
Black
(Momentary
Operating Function)
F
F
RECEPTACLE
SHAPE
Single
PHOTO INTERRUPTER
A
LEDS
6-pin Socket
C
Red
See Plug Options.
D
Amber
F
Green
ACTUATOR COLORS
B
White
C
Red
D
Amber
F
Green
PLUG OPTIONS
C2
Assembled Connector Plug
with Wire Leads
C3
Unassembled Connector
Plug and Pins
No
Code
No Connector Plug
Contact factory for custom options.
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
FP0115CAC1FF
Green Actuator with Green LED
Single Photo Transistor with
Normally Unshaded
Photo Interrupter
Round, Black Housing
No Connector Plug
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Contactless Pushbuttons
Series FP01
ACTUATOR & INTERRUPTER
Actuator Position
Normal
Model
FP0115
Down
1
Single
Photo
Transistor
Photo Interrupter
Unshaded
5
Schematics
Shaded
Normally Unshaded with
Momentary Shaded status
LED connector pins are 5 & 6;
interrupter connector pins are
3-4 & 1-2.
When shaded, the photo transistor momentarily activates
electrical function which signals the external device to
change its state.
6
5
4
3
2
1
HOUSING SHAPE & COLOR
C
A
Round Shape
Black Housing
INTERNAL RECEPTACLE
C1
Receptacle
Internal male connector socket
6 5 4 3 2 1
SWITCH SPECIFICATIONS
Status of Photo Interrupter:
Collector Current IC:
Status of Photo Transistor:
Output Condition of Photo Transistor:
Actuator Up
Actuator Down
Unshaded
Shaded
0.8mA minimum
10µA maximum
On
Off
IF = 20mA & VCE = 5V
MECHANICAL SPECIFICATIONS
Total Travel:
Operating Force:
Mechanical Life:
Operating Temperature Range:
.079” (2.0mm)
0.75 N (.169 lbf)
3,000,000 operations minimum
–25°C through +50°C (–13°F through +122°F)
MATERIALS
Actuator:
Polyacetal
Housing:
Polyamide
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series FP01
Contactless Pushbuttons
PHOTO INTERRUPTER SPECIFICATIONS
Electrical & Optical Characteristics
(Temperature @ 25°C)
Typical
Maximum
Condition
1.3V
1.6V
IF = 50mA
Reverse Current IR:
10µA
FR = 5V
Collector-Emitter Saturation Voltage VCE sat:
0.4V
IF = 20mA & IC = 0.1mA
Input
Forward Voltage VF:
Transmission
Absolute Maximum Ratings
Input LED
Output Photo Transistor
Forward Current IF:
Reverse Voltage VR:
Power Dissipation PD:
50mA
Collector-Emitter Voltage VCEO:
30V
5V
Emitter-Collector Voltage VECO:
4.5V
Collector Current IC:
80mW
30mA
Collector Dissipation PC:
80mW
Circuit Design Considerations
VCC = 5V
Output of the infrared LED in the photo
interrupter decreases approximately
50% after 100,000 hours.
180Ω
RL
VOUT
Threshold Voltage
VHI : 3.8V
VLO : 1.0V
Recommended load resistance (RL) is
40k ~ 120kΩ for the illustrated circuit.
GND
ACTUATOR COLORS
B
C
White
Red
D
F
Amber
Green
LED COLORS & SPECIFICATIONS
LEDs are an integral
part of the switch and
not available separately. The electrical
specifications shown
are determined at a
basic temperature of
25°C.
If the source voltage
exceeds the rated voltage, a ballast resistor
is required.
R
+
IF
Anode
C
D
F
Color
Red
Amber
Green
Forward Peak Current
IFM
30mA
25mA
25mA
Continuous Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.85V
2.0V
2.25V
Reverse Peak Voltage
VRM
5V
5V
5V
Current Reduction
Rate Above 25°C
∆IF
0.38mA
/°C
0.28mA
/°C
0.40mA
/°C
Single Element LED
VF
E
Cathode
–
R =
Where: R =
E =
VF =
IF =
E – VF
IF
Resistor Value (Ohms)
Source Voltage (V)
Forward Voltage (V)
Forward Current (A)
Ambient Temperature Range
–25° ~ +50°C
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series FP01
Contactless Pushbuttons
EXTERNAL PLUG OPTIONS
C2
AT021
Assembled Connector Plug
with Wire Leads
AT022
Unassembled Connector Plug
and Pins
C3
Connector plug body: JST model ZHR-6
Crimp connector pins: JST model SZH-002T-P0.5
Wire leads: 28-26AWG; 12-inch, unstripped;
Blue for Pin 1
No Code
No Connector Plug
1 connector plug and 8 crimp connector
pins only (no wire leads provided).
Recommended connector
plug for assembly:
JST model number ZHR-6
Matching wire leads: 28-26AWG
Recommended crimp
connector pins:
JST model SZH-002T-P0.5
for 28-26AWG wire leads
or SZH-003T-P0.5 for
32-28AWG wire leads.
TYPICAL SWITCH DIMENSIONS
NKK P/N
This Side
(5.0)
.197
Pin 1
(1.1)R Typ
.043
(25.1)
.988
(19.6) Dia
.772
(26.0) Dia
1.024
(22.9) Dia
.902
(1.5)
.059
(5.3)
.209
(21.4)
.843
(2.3)
.091
(22.8) Dia
.898
Recommended Panel
Thickness Range:
.098” ~ .197”
(2.5mm ~ 5.0mm)
6 5 4 3 2 1
Terminal Connector Detail
FP0115CAC1FF
LEGENDS
Easily create and submit your own legends using our new on-line Legend Maker.
LM
Visit www.nkkswitches.com
For other legend support options, customers may either contact the factory
or utilize the general information and basic specifications presented below.
Suggested Printable Area for FP01 Cap
T
ER
AL
Recommended Methods:
Pad Print or Laser Etch on cap.
Epoxy based ink is recommended.
(16.56) Dia
.475
(19.6) Dia
.772
(1.52) Typ
.060
Shaded area is printable area.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Similar pages