Source C-15-2500C-TDFB-SSC2 2.5 gbps single mode transceiver Datasheet

2.5 Gbps Single Mode Transceiver
C-1X-2500(C)-TDFB(3)-SSCX
Features
• SC Duplex Single Mode Transceiver
• Industry Standard 1x9 Footprint
• Complies with SONET OC-48 STM-16
• Single +3.3V / +5V Power Supply
• Operating Temperature Range 0℃ ~ +70℃
• CML Differential Data Inputs and Outputs
• PECL/LVPECL Signal Detection Output
[C-1X-2500-TDFB(3)-SSCX]
• TTL/LVTTL Signal Detection Output
[C-1X-2500C-TDFB(3)-SSCX]
• Wave Solderable and Aqueous Washable
• Uncooled laser diode with MQW structure
• Complies with Telcordia (Bellcore) GR-468-CORE
Applications
• STM 16/ OC-48, 2.5 Gigabit
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Unit
Note
Power Supply Voltage
Vcc
0
3.6
V
C-1X-2500(C)-TDFB3-SSCX
Power Supply Voltage
Vcc
0
6
V
C-1X-2500(C)-TDFB-SSCX
Output Current
Iout
0
30
mA
Soldering Temperature
-
-
260
ºC
Operating Temperature
Topr
0
70
ºC
Storage Temperature
Tstg
-40
85
ºC
Symbol
Min.
Typ.
Max.
Unit
Vcc
3.1
3.3
3.5
V
10 seconds on leads only
Recommended Operating Condition
Parameter
Power Supply Voltage 1
Power Supply Voltage
1
Operating Temperature (Case)
Vcc
4.75
5
5.25
V
Topr
0
-
70
ºC
-
-
2488.32
-
Mbit/s
Data Rate
Note1: Please refer to ordering information
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS797-Dec0904
rev. A.0
2.5 Gbps Single Mode Transceiver
C-1X-2500(C)-TDFB(3)-SSCX
Transmitter Specifications (Optical)
Parameter
Symbol
Min
Typical
Max
Unit
Optical Transmit Power
Po
-5
-
0
dBm
C-1X-2500(C)-TDFB(3)-SSC2
Optical Transmit Power
Po
0
-
+5
dBm
C-1X-2500(C)-TDFB(3)-SSC4
Output center Wavelength
λ
1280
1310
1355
nm
C-13-2500(C)-TDFB(3)-SSCX
λ
1500
1550
1580
nm
C-15-2500(C)-TDFB(3)-SSCX
∆λ
-
-
1
nm
-20 dB width
SMSR
30
35
-
dB
CW, Po=5mW
ER
8.2
-
-
dB
Output center Wavelength
Output Spectrum Width
Side Mode Suppression Ratio
Extinction Ratio
Output Eye
Notes
Compliant with ITU recommendation G.957
Relative Intensity Noise
RIN
-
-
-120
dB/Hz
TJ
-
-
0.18
ns
Symbol
Min
Typical
Max
Unit
ICC
-
-
260
mA
Data Input Current-Low
IIL
-350
-
-
µA
Data Input Current-High
IIH
-
-
350
µA
VIH-VIL
300
-
-
mV
Symbol
Min
Typical
Max
Unit
Total Jitter
Measured with 223-1 PRBS with 72 ones and
72 zeros
Transmitter Specifications (Electrical)
Parameter
Power Supply Current
Data Input Voltage
Notes
Maximum current is specified at
Vcc= Maximum @ maximum temperature
Peak-peak, single ended, AC coupled
Receiver Specifications (Optical)
Parameter
Sensitivity2
Notes
-
-
-
-20
dBm
Maximum Input Power
Pin
0
-
-
dBm
Signal Detect-Asserted
Pa
-
-
-20
dBm
Measured on transition: low to high
Signal Detect-Deasserted
Pd
-38
-
-
dBm
Measured on transition: high to low
1
-
-
dB
1100
-
1600
nm
-27
dB
Signal Detect-Hysteresis
Wavelength of Operation
Reflectance
Note 2: Measured with 223-1 PRBS, BER= 10-10
Receiver Specifications (Electrical)
Parameter
Power Supply Current
Data output Voltage
Symbol
Min
Typical
Max
Unit
Note
ICC
-
-
100
mA
The current excludes the output load current
VOH -VOL
300
-
900
mV
Peak-peak, single-ended, AC-coupled
Signal Detect Output Voltage-Low
VSDL
-
-
0.5
V
Signal Detect Output Voltage-High
VSDH
2.0
-
-
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-2.0
-
-1.58
V
Signal Detect Output Voltage-High
VSDH- Vcc
-1.1
-
-0.74
V
LUMINENTOIC.COM
C-1X-2500C-TDFB(3)-SSCX
C-1X-2500-TDFB(3)-SSCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS797-Dec0904
rev. A.0
2.5 Gbps Single Mode Transceiver
C-1X-2500(C)-TDFB(3)-SSCX
Connection Diagram
1. (Rx GND)
2. (Rx +)
3. (Rx-)
4. (SD)
5. (Rx Vcc)
6. (Tx Vcc)
7. (TX-)
8. (TX+)
9. (Tx GND)
NC
Top View
NC
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data in
Transmitter Signal Ground
PIN
Symbol
Notes
1
RxGND
Directly connect this pin to the receiver ground plane
2
RD+
See recommended circuit schematic
3
RD-
See recommended circuit schematic
4
SD
Active high on this indicates a received optical signal
5
RxVcc
DC power for the receiver section
6
TxVcc
DC power for the transmitter section
7
TD-
See recommended circuit schematic
TD+
See recommended circuit schematic
8
Warnings
9
LUMINENTOIC.COM
TxGND
Directly connect this pin to the transmitter ground plane
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS797-Dec0904
rev. A.0
2.5 Gbps Single Mode Transceiver
C-1X-2500(C)-TDFB(3)-SSCX
Recommended Circuit Schematic
C-1X-2500-TDFB(3)-SSCX
Rx Vcc
9
8
7
6
5
4 3
2
1
C5
R1
TD +
Z=50!
TD -
Z=50!
Z=50!
RD +
Z=50!
RD SD
Tx Vcc
Rx Vcc
No internal
connection
Notes +3.3V:
C1=C2=C5=0.1"F
C3=C4=10"F
L1=L2=1"H
R1=130!
R2=82!
Transceiver
Top view
R2
No internal
connection
L1
C3
Vcc
Notes +5V:
C1=C2=C5=0.1"F
C3=C4=10"F
L1=L2=1"H
R1=82!
R2=130!
Rx Vcc
C1
L2
Tx Vcc
C2
C4
C-1X-2500C-TDFB(3)-SSCX
7 6 5
9 8
TD +
Z=50!
TD -
Z=50!
4 3 2
1
Z=50!
RD +
Z=50!
RD SD
Tx Vcc
Rx Vcc
No internal
connection
Transceiver
Top view
No internal
connection
L1
Notes:
C1=C2=0.1"F
C3=C4=10"F
L1=L2=1"H
Vcc
C3
Rx Vcc
C1
L2
C4
Tx Vcc
C2
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS797-Dec0904
rev. A.0
2.5 Gbps Single Mode Transceiver
C-1X-2500(C)-TDFB(3)-SSCX
Package Diagram
Units in mm
SC Transceiver Assembly 9.8mm
Front View
Top View
Rear View
Side View
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS797-Dec0904
rev. A.0
2.5 Gbps Single Mode Transceiver
C-1X-2500(C)-TDFB(3)-SSCX
Ordering Information
Available Options:
C-13-2500-TDFB-SSC2
C-13-2500C-TDFB-SSC2
C-13-2500-TDFB3-SSC2
C-13-2500C-TDFB3-SSC2
C-15-2500-TDFB-SSC2
C-15-2500C-TDFB-SSC2
C-15-2500-TDFB3-SSC2
C-15-2500C-TDFB3-SSC2
C-13-2500-TDFB-SSC4
C-13-2500C-TDFB-SSC4
C-13-2500-TDFB3-SSC4
C-13-2500C-TDFB3-SSC4
C-15-2500-TDFB-SSC4
C-15-2500C-TDFB-SSC4
C-15-2500-TDFB3-SSC4
C-15-2500C-TDFB3-SSC4
Part numbering Definition:
C - 1X - 2500(C) - TDFB(3) - S SC TxPower
• 13 = Wavelength 1310nm
15 = Wavelength 1550nm
• Communication protocol
(2.5 Gbps)
2500 = PECL Signal Detection Output
2500C = TTL Signal Detection Output
• TDFB = +5V Transceiver, DFB
TDFB3= +3.3V Transceier, DFB
• Single mode fiber
• Connector options
• Tx Power range
2 = -5 to 0 dBm
4 = 0 to +5 dBm
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS797-Dec0904
rev. A.0
Similar pages